Ionic liquids to the rescue? Overcoming the ionic conductivity limitations of polymer electrolytes

Polymer electrolytes – solid polymeric membranes with dissolved salts – are being intensively studied for use in all-solid-state lithium-metal-polymer (LMP) batteries to power consumer electronic devices. The low ionic conductivity at room temperature of existing polymer electrolytes, however, has seriously hindered the development of such batteries for many applications. The incorporation of salts molten at room temperature (room temperature ionic liquids or RTILs) into polymer electrolytes may be the necessary solution to overcoming the inherent ionic conductivity limitations of ‘dry’ polymer electrolytes.     

Investigation of mechanical properties of polyvinyl chloride-polyethylene oxide (PVC-PEO) based polymer electrolytes for lithium polymer cells

Polymer electrolytes composed of a blend of polyvinyl chloride-polyethylene oxide (PVC-PEO) as a host polymer, lithium triflate (LiCF₃SO₃) as a salt, mixture of ethylene carbonate (EC) and dibuthyl phthalate (DBP) as plasticizers and silica (SiO₂) as the nanocomposite filler were studied. Results suggest that PVC-PEO blending exhibits improved mechanical strength compared to that of pure PEO. The introduction of LiCF₃SO₃ changes the mechanical properties of PVC-PEO blends from hard and brittle to soft and tough. In PVC-PEO:LiCF₃SO₃ (70:30) system, the Young’s modulus value decreases from 5.30 × 10⁻¹ MPa to 4.78 × 10⁻⁴ MPa and the elongation at peak value increases from 3.71 mm to 32.09 mm with the incorporation of DBP and EC. The deteriorated mechanical properties with the addition of plasticizers are overcome with the addition of SiO₂ as nanocomposite filler. In PVC-PEO-LiCF₃SO₃-DBP-EC system, the addition of 5% SiO₂ increases the Young’s modulus value from 4.78 × 10⁻⁴ MPa to 1.51 × 10⁻³ MPa. The improvement of the mechanical properties reveals greater dispersion of SiO₂ particles in PVC-PEO blend based polymer electrolytes. In practical lithium polymer cells, inorganic fillers are frequently added to improve the mechanical strength of the electrolyte films.     

Preparation and characterization of pva based solid polymer electrolytes for electrochemical cell applications

Solid polymer electrolyte films containing poly(vinyl alcohol) (PVA) and magnesium nitrate (Mg(NO3)2) were prepared by solution casting technique and characterized by using XRD, FTIR, DSC and AC impedance spectroscopic analysis. The amorphous nature of the polymer electrolyte films has been confirmed by XRD. The complex formation between PVA and Mg salt has been confirmed by FTIR. The glass transition temperature decreases with increasing the Mg salt concentration. The AC impedance studies are performed to evaluate the ionic conductivity of the polymer electrolyte films in the range of 303 383 K, and the temperature dependence seems to obey the Arrhenius behavior. Transport number measurements show that the charge transport is mainly due to ions. Electrochemical cell of configuration Mg/(PVA + Mg(NO3)2) (70:30)/(I2 + C + electrolyte) has been fabricated. The discharge characteristics of the cell were studied for a constant load of 100 kΩ.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and modified montmorillonite

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer, which is superior to poly(ethylene oxide) in mechanical stability due to its cross-linked structure, modified montmorillonite (MMMT) and LiClO₄, and CGPE with good mechanical strength comprises of the CSPE and LiClO₄–PC (propylene carbonate) solution. The ionic conductivity can be enhanced after the addition of MMMT, and CGPE exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature. The temperature dependence of the ionic conductivity of the CSPE follows the Vogel–Tamman–Fulcher (VTF) equation. The effects of MMMT on the interactions in these systems and the possible conduction mechanisms are also discussed.     

Characterization of poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) electrolytes complexed with different lithium salts

Poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) gel electrolytes comprising a combination of plasticizers, ethylene carbonate (EC) and propylene carbonate (PC) and lithium salt LiX have been prepared using the solution casting technique in an argon atmosphere. The prepared electrolytes were subjected to ionic conductivity, compatibility with lithium metal anode and thermogravimetric (TG)/differential thermal analysis (DTA). The membranes, which possess lithium salt, LiBF₄ exhibited maximum conductivity and on contrary it undergoes severe passivation with lithium metal. All these membranes are found to be stable thermally about 70 °C.     

High ionic conductivity of all-solid polymer electrolytes based on polyorganophosphazenes

A series of all-solid polymer electrolytes were prepared by cross-linking new designed poly(organophosphazene) macromonomers. The ionic conductivities of these all-solid, dimensional steady polymer electrolytes were reported. The temperature dependence of ionic conductivity of the all-solid polymer electrolytes suggested that the ionic transport is correlated with the segmental motion of the polymer. The relationship between lithium salts content and ionic conductivity was discussed and investigated by Infrared spectrum. Furthermore, the polarity of the host materials was thought to be a key to the ionic conductivity of polymer electrolyte. The all-solid polymer electrolytes based on these poly(organophosphazenes) showed ionic conductivity of 10⁻⁴ S cm⁻¹ at room temperature.     

Highly concentrated polycarbonate‐based solid polymer electrolytes having extraordinary electrochemical stability

Solid polymer electrolytes (SPEs) are compounds of great interest as safe and flexible alternative ionics materials, particularly suitable for energy storage devices. We study an unusual dependence on the salt concentration of the ionic conductivity in an SPE system based on poly(ethylene carbonate) (PEC). Dielectric relaxation spectroscopy reveals that the ionic conductivity of PEC/lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) electrolyte continues to increase with increasing salt concentration because the segmental motion of the polymer chains is enhanced by the plasticizing effect of the imide anion. Fourier transfer‐infrared (FTIR) spectroscopy suggests that this unusual phenomenon arises because of a relatively loose coordination structure having moderately aggregated ions, in contrast to polyether‐based systems. Comparative FTIR study against PEC/lithium perchlorate (LiClO₄) electrolytes suggests that weak ionic interaction between Li and TFSI ions is also important. Highly concentrated electrolytes with both reasonable conductivity and high lithium transference number (t₊) can be obtained in the PEC/LiTFSI system as a result of the unusual salt concentration dependence of the conductivity and the ionic solvation structure. The resulting concentrated PEC/LiTFSI electrolytes have extraordinary oxidation stability and prevent any Al corrosion reaction in a cyclic voltammetry. These are inherent effects of the highly concentrated salt. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2442–2447     

Thermal and electrochemical characteristics of plasticized polymer electrolytes based on poly(acrylonitrile-co-methyl methacrylate)

The thermal and electrochemical characteristics of plasticized polymer electrolytes composed of poly(acrylonitrile-co-methyl methacrylate) [P(AN-co-MMA)], a plasticizer [a mixture of ethylene carbonate and propylene carbonate], and LiCF₃SO₃ were investigated. The incorporation of a MMA unit into the matrix polymer was effective for an increase in the compatibility between the matrix polymer and the plasticizer. The comparative investigation of the interfacial resistance of the Li/polymer electrolyte/Li cell for the PAN-based and the P(AN-co-MMA)-based polymer electrolytes showed that the MMA unit could improve the stability of the polymer electrolyte toward the Li electrode, which is probably due to the enhanced adhesion of the polymer electrolyte to the Li electrode. Received: 14 July 1997 / Accepted: 14 May 1998     

Electrochemical characterization of plasticized polymer electrolytes based on ABS/PMMA blends

Electrochemical characteristics of plasticized polymer electrolytes based on poly(acrylonitrile-butadene-styrene) and poly(methyl methacrylate) (abbreviated as ABS/PMMA) blends have been studied. The ionic conductivity of the polymer electrolyte with an ABS/PMMA ratio of 6/4 and a plasticizer content of 60% was highest when the LiClO₄ content was 4.8%. The transference numbers (T ₊) of the polymer electrolytes were measured using the steady-state current method, and the T ₊ values were found to be less than 0.5. The electrolyte system was found to have an electrochemical stability window up to 4.5 V. The properties of the electrode interface in contact with the polymer electrolyte were also investigated by impedance spectroscopy, and the evolution of these spectra as a function of storage time was explained and interpreted using a solid-polymer layer (SPL) model. The time evolution of the impedance parameters indicated that a passivation film grew rapidly on the lithium surface immediately after assembly of the cell. Electronic Publication     

Recent advances in solid-state polymer electrolytes and innovative ionic liquids based polymer electrolyte systems

Solid polymer electrolytes are a promising alternative to widely used liquid carbonate electrolytes to deliver next-generation lithium-ion batteries with improved safety. However, the limited ionic conductivity and high interfacial resistance with electrodes limit their widespread use. This review aims to give an overview of the recent research on performance aspects and strategies of solid polymer electrolytes, including ionic conductivity, lithium transference number, design flexibility, scale-up, and integration of ionic liquids with a focus on safety.     

Novel zinc ion conducting polymer gel electrolytes based on ionic liquids

We report novel zinc ion conducting polymer gel electrolytes (PGEs) based on non-volatile room temperature ionic liquids. The PGEs consist of an ionic liquid, with a zinc salt dissolved in it, blended with a polymer matrix, poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP). The resultant electrolyte membranes are freestanding, translucent, flexible and elastic, with excellent mechanical integrity and strength. They possess exceptional thermal stability, exhibit essentially no weight loss under dynamic vacuum or upon heating to 200 °C, and remain the same gel phase in wide temperature ranges, with ionic conductivities on the order of 10⁻³ S/cm at room temperature, 10⁻⁴ S/cm at −20 °C and 4–5 × 10⁻³ S/cm at 80 °C. Electrochemical tests show that zinc ions are mobile in the membranes and zinc metal is capable of dissolution into and deposition from the membranes. The membranes also exhibit wide electrochemical stability windows. The results of this study demonstrate the promise of developing PGEs based on ionic liquids for potential application in next-generation non-aqueous zinc battery systems.     

Investigations on poly(methyl methacrylate)-poly(ethylene oxide) hybrid polymer electrolytes with dioctyl phthalate, dimethyl phthalate and diethyl phthalate as plasticizers

Plasticizers can be used to change the mechanical and electrical properties of polymer electrolytes by reducing the degree of crystallinity and lowering the glass transition temperature. The transport properties of gel-type ionic conducting membranes consisting of poly(ethylene oxide) (PEO), poly(methyl methacrylate) (PMMA), LiClO₄ and dioctyl phthalate, diethyl phthalate or dimethyl phthalate (DMP) are studied. The polymer films are characterized by X-ray diffraction, Fourier transform infrared and impedance spectroscopic studies. It is found that the addition of DMP as the plasticizer in the PEO-PMMA-LiClO₄ polymer complex favours an enhancement in ionic conductivity. The maximum conductivity value obtained for the solid polymer electrolyte film at 305 K is 3.529×10^{– 4} S cm^–1. Electronic Publication     

Poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) based composite electrolytes for lithium batteries

The composite polymer electrolyte (CPE) membranes, comprising of poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP), aluminum oxyhydroxide, (AlO[OH]_n) of two different particle sizes 7 μm/14 nm and LiN(CF₃SO₂)₂ as lithium salt were prepared using solution casting technique. The prepared membranes were subjected to XRD, impedance spectroscopy, compatibility and transport number studies. The incorporation of nanofiller greatly enhanced the ionic conductivity and the compatibility of the composite polymer electrolyte. Also LiCr_0.01Mn_1.99O₄/CPE/Li cells were assembled and their charge-discharge profiles have been made at 70 °C. The film which possesses nanosized filler offered better electrochemical properties than those with micron sized filler. The results are discussed based on Lewis acid-base theory.     

Studies on ionics conduction properties of modification CMC-PVA based polymer blend electrolytes via impedance approach

In this study, the modification of cellulose derivative namely carboxymethyl cellulose (CMC) blended with polyvinyl alcohol (PVA) and doped with different content of NH₄Br based solid polymer electrolytes (SPEs) prepared via solution casting method is investigated. The FTIR analysis demonstrated the interaction between CMC-PVA and NH₄Br via COO⁻. The optimum ionic conductivity at ambient temperature is found to be 3.21 × 10⁻⁴ S/cm for the sample containing 20 wt% NH₄Br with the lowest percentage of crystallinity and total weight loss. The conductivity-temperature relationship for the entire SPEs system obeys Arrhenius behaviour. Besides that, based on the Nyquist fitting analysis, it is shown that the ionic conductivity of the SPEs is primarily influenced by the ionic mobility as well as the ions diffusion coefficient. The H⁺ transference number obtained using non-blocking reversible electrode is 0.31, which further indicates that the conduction species is predominantly due to the cationic conduction.     

Polymer electrolyte for lithium batteries based on photochemically crosslinked poly(ethylene oxide) and ionic liquid

Polymer/ionic liquid composites were investigated as solvent-free electrolytes for lithium batteries. Ternary electrolytes based upon poly(ethylene oxide), an ionic liquid and a conducting salt were UV crosslinked with benzophenone as the photoinitiator. Crosslinking leads to an increase in mechanical stability of the PEO composites. This straight-forward process provides a way to increase the content of ionic liquid and thus to raise ionic conductivity without loss of mechanical stability. Impedance measurements showed that the ionic conductivity of the composites is not affected by the UV curing process. Moreover, the UV curing process causes a decrease in the degree of crystallinity in the PEO composites which contributes to an increase in ionic conductivity. The present work is related to safety issues of lithium batteries.     

Enhancing the ionic conductivity in a composite polymer electrolyte with ceramic nanoparticles anchored to charged polymer brushes

Polymer electrolytes a re essential for next-gene ration lithium batteries because of their excellent safety record.However,low ionic conductivity is the main obstacle restricting their commercial application.Composites with nanoparticles are a promising route to overcome this obstacle.In this work,lithium polystyrene sulfonate brushes(LiPSS)is anchored to silicon dioxide nanoparticles with chemical bonding using atom transfer radial polymerization(SI-ATRP).The composite polymer electrolytes are made by mixing vinylene carbonate and nanoparticles via a facile in situ polymerization process.The ionic conductivity of composite polymer electrolytes is improved to 7.2×10^-4 S/cm at room temperature,which is attributed to the low degree of crystallinity of polymer electrolyte and the fast ion transport on the surfaces of polymer brush layers that act as a conductive network.The composite polymer electrolytes show a wide electrochemical window of approximately 4.5 V vs.Li^+/Li and excellent cycling performance retention of approximately 95%after 100 cycles at ambient temperature.The results also prove that surface groups of ceramic na noparticles are an important way to increase the electrochemical properties of composite polymer electrolytes.     

Amphiphilic polymer gel electrolytes. I. preparation of gels based on poly(ethylene oxide) graft copolymers containing different ionophobic groups

Amphiphilic graft copolymers were prepared via the radical copolymerization of poly(ethylene oxide) (PEO) macromonomers with fluorocarbon or hydrocarbon acrylates in toluene with 2,2′‐azobisisobutyronitrile (AIBN) as an initiator. ¹H NMR spectroscopy confirmed that the composition of the graft copolymers corresponded well to the monomer feed. For gel electrolytes prepared from the amphiphilic copolymers, the nature of the ionophobic parts of the amphiphilic graft copolymers had a great influence on the ion conductivity. Gel electrolytes based on graft copolymers containing fluorocarbon side chains showed significantly higher ion conductivity than electrolytes based on graft copolymers containing hydrocarbon groups. The ambient‐temperature ion conductivity was about 2.6 mS/cm at 20 °C for a gel electrolyte based on an amphiphilic graft copolymer consisting of an acrylate backbone carrying PEO and fluorocarbon side chains. Corresponding gels based on graft copolymers with PEO side chains and hydrocarbon groups showed an ambient‐temperature ion conductivity of about 1.2 mS/cm. The gel electrolytes contained 30 wt % copolymer and 70 wt % 1 M LiPF₆ in an ethylene carbonate/γ‐butyrolactone (2/1 w/w) mixture. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2223–2232, 2001     

Effects of ceramic filler in poly(vinyl chloride)/poly(ethyl methacrylate) based polymer blend electrolytes

Effects of nano-ceramic filler titanium oxide (TiO₂) have been investigated on the ionic conductance of polymeric complexes consisting of poly(vinyl chloride) (PVC)/poly(ethyl methacrylate) (PEMA), and lithium perchlorate (LiClO₄). The composite polymer blend electrolytes were prepared by solvent casting technique. The TiO₂ nanofillers were homogeneously dispersed in the polymer electrolyte matrix and exhibited excellent interconnection with PVC/PEMA/PC/LiClO₄ polymer electrolyte. The addition of TiO₂ nanofillers improved the ionic conductivity of the polymer electrolyte to some extent when the content of TiO₂ is 15 wt%. The addition of TiO₂ also enhanced the thermal stability of the electrolyte. The changes in the structural and complex formation properties of the materials are studied by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. The scanning electronmicroscope image of nano-composite polymer electrolyte membrane confirms that the TiO₂ nanoparticles were distributed uniformly in the polymer matrix.     

Borate ester plasticizer for PEO-based solid polymer electrolytes

Lithium rechargeable batteries featuring solvent-free highly conductive solid polymer electrolytes (SPEs) will make a dramatic impact on the electric and hybrid-electric vehicles (EV/HEV) industry by eliminating hazards related to the use of liquid electrolytes. In this paper, we report the synthesis and characterization of a star-shaped borate ester plasticizer, which was then incorporated into the poly(ethylene oxide) polymer matrix in different proportions. Significant improvement was observed in conductivity, with the best value of 9.1 × 10⁻⁵ S/cm at 30 °C. These borate ester plasticized SPEs also exhibited excellent thermal and electrochemical stabilities.     

Structural and transport characteristics of polyethylene oxide/phenolic resin blend solid polymer electrolytes

Details on the structure and transport characteristics of the solid polymer electrolyte polyethylene oxide (PEO)/lithium salt (LiClO₄) modified by novolac phenolic resin are presented here. From IR spectra it could be concluded that complex formation occurred through multiple interactions between the ether oxygen of PEO–lithium, phenolic lithium, and the phenolic ether oxygen of PEO. The free hydroxyl band in phenolic reflected that phenolic closely interacted with both the PEO polymer and ionic salt. With increasing salt content in PEO, the vibration band corresponding to the ClO anion (～623 cm^?1) displayed growth of a shoulder at ～635 cm^?1, suggesting the formation of Li⁺…ClO₄^? ion pairing. However, in the presence of phenolic, ion‐pairing formation was effectively suppressed, which suggested that the phenolic moiety facilitated a greater degree of LiClO₄ salt dissociation. Activation energy analysis revealed two conducting pathways: one through the amorphous PEO and the other through the PEO/phenolic amorphous matrix. The high ion conductivity originated from effective salt dissociation and the establishment of a new conduction network formed by PEO and phenolic. Furthermore, the structural modification also extended the thermal stability and mechanical strength of the solid polymer electrolyte composite. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3866–3875, 2004