复合电沉积CoNiP-BaFe12O19磁性薄膜

采用复合电沉积技术制备了磁性CoNiP-BaFe12O19复合薄膜, 分别用SEM、EDS、XRD、VSM 对复合薄膜进行了表征. SEM、EDS、XRD 测试表明BaFe12O19粒子被成功地掺入CoNiP硬磁薄膜中. 考察了基础电解液和复合电解液的电化学行为, 并探讨了BaFe12O19粒子和表面活性剂CTAB 的加入对薄膜中各成分相对含量的影响. 结果表明, 当表面活性剂CTAB 加入量为0.6 g·L-1时, 复合膜中BaFe12O19相对含量最高达20%. VSM 测试表明BaFe12O19粒子的掺入显著地增加了薄膜的矫顽力和剩磁比.     

Comparison of the Sol-gel Method with the Coprecipitation Technique for Preparation of Hexagonal Barium Ferrite

Hexagonal barium ferrite BaFe12O19 particles were prepared by sol-gel and coprecipitation methods, respectively. The composition of the so-obtained materials was investigated by means of XRD. By the sol-gel method, non-anticipated intermediate crystalline phases, such as γ-Fe2O3, α-Fe2O3, BaCO3, and BaFe2O4 etc., were formed with the delay of the formation of BaFe12O19. The formation of single phase BaFe12O19 required calcination at 850 oC for 4 h. On the other hand, using coprecipitation technique, amorphous hydroxide precursor was directly transferred into BaFe12O19 almost without the formation of intermediate crystalline phases. BaFe12O19 was prepared by calcining at 700 oC for 3 h. The results were confirmed by ESEM and VSM analyses. Based on the already reported results and the observed results in this study, it can be concluded that the coprecipitaion technique is easier to control than the sol-gel method for preparation of BaFe12O19 at a low temperature.     

稳恒磁场下水热法制备钡铁氧体

利用XRD,SEM,TEM和振动样品磁强计(VSM)等检测手段对不同磁场强度下水热法制备的钡铁氧体粉末进行了分析.实验结果表明,无磁场下,150℃时得到的产物为BaFe2O4颗粒,而180℃时产物为片状BaFe12O19施加磁场后,150和180℃下水热反应产物都为棒状BaFe12O19随着磁感应强度的增加,水热反应产...     

Synthesis and Electro-magnetic Properties of Polyaniline-barium Ferrite Nanocomposite

"The polyaniline (PANI)-barium ferrite composite with magnetic behavior was synthesized by in situ poly-merization of aniline in the presence of BaFe12O19 nanoparticles of 60-80 nm in diameters. The structure, morphology and magnetic properties of samples were characterized by powder X-ray diffraction, Fourier transform infrared, scanning electron microscopy, transmission electron microscopy and vibrating sample magnetometer technique. The results of spectroanalysis indicated that there was interaction between PANIchains and ferrite particles. The composite exhibited the hysteresis loops of the ferromagnetic nature. The saturated magnetization of composite was 22.2 emu/g and the conductance was 0.069 S/cm."     

钡铁氧体包覆碳纤维的制备及毫米波衰减性能

通过溶胶凝胶法,在碳纤维表面均匀包覆了一层厚度约为1 μm的钡铁氧体(BaFe₁₂O₁₉)。采用SEM、FTIR、XRD、XPS等技术对碳纤维/钡铁氧体复合材料的组成、结构、性能进行了表征和分析。利用8 mm波雷达装置测试了碳纤维、碳纤维/钡铁氧体复合材料的毫米波衰减性能。实验结果表明：由于碳纤维/钡铁氧体复合材料兼具电损耗和磁损耗吸收,其8 mm波衰减性能明显优于单纯的碳纤维。     

聚苯胺钡铁氧体纳米复合材料的制备、表征及性能

采用原位掺杂聚合法, 将聚苯胺(PANI)对粒径在60~80 nm的M型钡铁氧体颗粒(BaFe12O19)进行了包覆, 得到了具有棒状结构的复合材料. 通过X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等测试手段对材料的形貌和结构进行了表征. 结果表明, PANI链段与BaFe12O19颗粒之间存在作用力. 使用振动磁强计和四探针法测定了复合材料的磁性能与电性能后发现, 饱和磁化强度与矫顽力均随聚苯胺含量的增加呈规律性下降趋势, 而电导率呈上升趋势. 复合材料的吸收特性测试结果表明, 该材料反射率小于-20 dB时, 带宽可以达到15.07 GHz. 同时详细地讨论了纳米复合材料的聚合机理及相互作用.     

形貌可控纳米SrFe_(12)O_(19)的制备及其磁性能

以FeCl3为原料,NaOH作为沉淀剂,通过化学沉淀法,制备出球状的Fe(OH)3中间体,同时以FeCl2为原料,采用化学沉淀法,分别使用NH3·H2O、Na2CO3和NaOH作为沉淀剂制得了不同形貌的中间体,利用柠檬酸法在中间体表面包裹锶的柠檬酸络合物,煅烧后分别制得了球形、纺锤体及棒状的纳米SrFe12O19.利用X射线衍射(XRD)和透射电镜(TEM)等测试手段对不同形貌的纳米SrFe12O19进行表征,并利用振动样品磁强计(VSM)对磁性能进行研究.结果表明:在用化学沉淀-柠檬酸法制备SrFe12O19的过程中,铁盐的种类以及沉淀剂的碱性对中间体的物相和SrFe12O19的形貌有着至关重要的影响.当原料为Fe3+时,制得了球形的纳米SrFe12O19;当原料为Fe2+时,利用碱性不同的沉淀剂可制得不同形貌的纳米SrFe12O19.随着沉淀剂碱性的增加,所得SrFe12O19的长径比增加,形貌各向异性增加.SrFe12O19的矫顽力(Hc)主要取决于粒子的各向异性,各向异性越大,矫顽力越大,饱和磁化强度(Ms)随着样品的各向异性的增加也有所增加,以FeCl2为原料,NaOH作为沉淀剂时制得的棒状SrFe12O19的矫顽力和饱和磁化强度最大分别为458.2kA·m-1和64.2A·m2·kg-1.     

均匀共沉淀法制备钛酸钡-钡铁氧体核-壳结构粒子

用均匀共沉淀法制备了钛酸钡-钡铁氧体核-壳粒子, 研究了沉淀反应温度、尿素/金属离子摩尔比值(R)和BaTiO₃浓度对核-壳粒子形貌和结构的影响, 探讨了钛酸钡-钡铁氧体核-壳粒子在焙烧时的形成过程及其磁性能. 采用透射电子显微镜(TEM)、X射线衍射(XRD)分析仪对钛酸钡-钡铁氧体前驱物核-壳粒子及钛酸钡-钡铁氧体核-壳粒子的形貌和结构进行了表征, 采用振动样品磁强计(VSM)研究了钛酸钡-钡铁氧体核-壳粒子的磁性能. 结果表明: 当沉淀反应温度为100 °C, R为180, BaTiO₃浓度为2.5 g·L^-1时, 金属离子沉淀完全, 得到的钛酸钡-钡铁氧体前驱物核-壳粒子包覆层均匀、完整、光滑, 厚度约为10 nm. 过高的温度和R值都会导致大量独立颗粒杂质的生成; 随着BaTiO₃浓度的增大, 包覆层厚度有减小的趋势. 当焙烧温度为900 °C时, 壳层中开始形成BaFe₁₂O₁₉相, 其形成过程为晶态的α-Fe₂O₃和BaCO₃首先生成中间相BaFe₂O₄, 然后由BaFe₂O₄和α-Fe₂O₃反应得到最终的BaFe₁₂O₁₉. 当焙烧温度为1000 °C时, 壳层完全转化为BaFe₁₂O₁₉相. 随着焙烧温度从900 °C升高到1000 °C, 所得BaTiO₃-BaFe₁₂O₁₉核-壳粒子的饱和磁化强度从16.5 A·m²·kg^-1增加到39.5 A·m²·kg^-1, 矫顽力从340 kA·m^-1略微降低到316 kA·m^-1.     

A novel microwave absorber — BaAl2Fe10O19/poly(m-toluidine) composite: Preparation and electromagnetic properties

BaFe10Al2O19 /poly(m-toluidine)(BFA/PMT) composites were synthesized by in-situ polymerization of m-toluidine in the presence of BaFe10Al2O19 particles.The structure,composition and morphology of the obtained samples were characterized by using XRD,FT-IR,UV-visible spectroscopy,SEM and TEM techniques.Their electrical conductivity,magnetic property and microwave absorbing property were measured by the four-probe meter,the vibrating sample magnetometer and the vector network analyzer,respectively.The results indicated that BFA particles were coated effectively by PMT polymer and some interactions between PMT and BFA particles existing in the composites.The conductivity of BFA/PMT composite is smaller than that of pure polymers and its saturation magnetization is a little smaller than that of pure BFA.The influence of the constitution and film thickness of absorbent on its microwave absorbing property is evident.The microwave absorbing properties of the BFA/PMT composites are better than those of pure BFA and PMT.When optimizing the mass rate of BFA/PMT to 0.3,the absorbent with 2 mm film thickness has the minimum reflection loss of 28.26 dB at approximate 14.24 GHz,and the maximum available bandwidth of 8.8 GHz,respectively.The results show that these composites can be used as advancing absorption and shielding materials due to their favorable microwave absorbing property.     

External magnetic field-induced mesoscopic organization of Fe3O4 pyramids and carbon sheets

The current investigation is centered on the thermal decomposition of iron(II) acetyl acetonate, Fe(C5H7O2)2, in a closed cell at 700 degrees C, which is conducted under a magnetic field (MF) of 10 T. The product is compared with a similar reaction that was carried out without a MF. This article shows how the reaction without a MF produces spherical Fe3O4 particles coated with carbon. The same reaction in the presence of a 10 T MF causes the rejection of the carbon from the surface of pyramid-shaped Fe3O4 particles, increases the Fe3O4 particle diameter, forms separate carbon particles, and leads to the formation of an anisotropic (long cigarlike) orientation of Fe3O4 pyramids and C sheets. The macroscopic orientation of Fe3O4 pyramids+C sheets is stable even after the removal of an external MF. The suggested process can be used to fabricate large arrays of uniform wires comprised of some magnetic nanoparticles, and to improve the magnetic properties of nanoscale magnetic materials. The probable mechanism is developed for the growth and assembly behavior of magnetic Fe3O4 pyramids+C sheets under an external MF. The effect of an applied MF to synthesize morphologically different, but structurally the same, products with mesoscopic organization is the key theme of the present paper.     

新颖的电磁波吸收材料:Ba_(1-x)La_xFe_(10)Al_2O_(19)铁氧体的制备和性能

用溶胶-凝胶法合成了Ba1-xLaxFe10Al2O19铁氧体(x=0.00,0.05,0.10,0.15,0.20,0.25).通过粉末X射线衍射仪、扫描电子显微镜、透射电子显微镜、振动样品磁强计和矢量网络分析仪表征了样品的结构、形貌、磁性和电磁波吸收性能.结果表明,La含量显著地影响Ba1-xLaxFe10Al2O19铁氧体的磁性和电磁波吸收性能.Ba1-xLaxFe10Al2O19铁氧体的饱和磁化强度随La含量的增加而减小,而矫顽力则增大.当BaFe10Al2O19吸收剂的涂层厚度为2mm时,在8～18GHz范围内,反射损耗的峰值在13.45GHz处达到-26.3dB,有效带宽为8.9GHz.Ba1-xLaxFe10Al2O19铁氧体对电磁波的反射损耗和有效带宽低于母体BaFe10Al2O19.由于Ba1-xLaxFe10Al2O19样品良好的吸波性能,建议可以作为吸收和屏蔽电磁波的候选材料.     

化学自组装法制备钡铁氧体亚微空心球

描述了一种基于化学自组装制备钡铁氧体亚微空心球的新颖方法, 即以聚(苯乙烯-共-丙烯酸)乳胶粒子为模板, 利用酸醇相互作用, 将在聚乙二醇水溶液中得到的钡铁氧体前驱物包覆在模板粒子上, 形成聚(苯乙烯-共-丙烯酸)/钡铁氧体前驱物核壳纳米复合粒子. 复合粒子经历750 ℃的热处理, 可获得主晶相为BaFe12O19的钡铁氧体亚微空心球. 该空心球有可能在微波吸收、电磁流变等领域得到重要应用.     

Anisotropic magnetoresistance and piezoresistivity in structured Fe3O4-silver particles in PDMS elastomers at room temperature

Magnetorheological elastomers, MREs, based on elastic organic matrices displaying anisotropic magnetoresistance and piezoresistivity at room temperature were prepared and characterized. These materials are dispersions of superparamagnetic magnetite forming cores of aggregated nanoparticles inside silver microparticles that are dispersed in an elastomeric polymer (poly(dimethylsiloxane), PDMS), curing the polymer in the presence of a uniform magnetic field. In this way, the elastic material becomes structured as the application of the field induces the formation of filaments of silver-covered inorganic material agglomerates (needles) aligned in the direction of the field (parallel to the field). Because the magnetic particles are covered with silver, the MREs are not only magnetic but also electrical conductors. The structuration induces elastic, magnetic, and electrical anisotropic properties. For example, with a low concentration of particles in the elastic matrix (5% w/w) it is possible to obtain resistances of a few ohms when measured parallel to the needles or several megaohms in the perpendicular direction. Magnetite nanoparticles (Fe(3)O(4) NP) were synthesized by the coprecipitation method, and then agglomerations of these NPs were covered with Ag. The average size of the obtained magnetite NPs was about 13 nm, and the magnetite-silver particles, referred to as Fe(3)O(4)@Ag, form micrometric aggregates (1.3 μm). Nanoparticles, microparticles, and the MREs were characterized by XRD, TEM, SEM, EDS, diffuse reflectance, voltammetry, VSM, and SQUID. At room temperature, the synthesized magnetite and Fe(3)O(4)@Ag particles are in a superparamagnetic state (T(B) = 205 and 179 K at 0.01 T as determined by SQUID). The elastic properties and Young's modulus of the MREs were measured as a function of the orientation using a texture analysis device. The magnetic anisotropy in the MRE composite was investigated by FMR. The electrical conductivity of the MRE (σ) increases exponentially when a pressure, P, is applied, and the magnitude of the change strongly depends on what direction P is exerted (anisotropic piezoresistivity). In addition, at a fixed pressure, σ increases exponentially in the presence of an external magnetic field (H) only when the field H is applied in the collinear direction with respect to the electrical flux, J. Excellent fits of the experimental data σ versus H and P were achieved using a model that considers the intergrain electron transport where an H-dependent barrier was considered in addition to the intrinsic intergrain resistance in a percolation process. The H-dependent barrier decreases with the applied field, which is attributed to the increasing match of spin-polarization in the silver covers between grains. The effect is anisotropic (i.e., the sensitivity of the magnetoresistive effect is dependent on the relative orientation between H and the current flow J). In the case of Fe(3)O(4)@ Ag, when H and J are parallel to the needles in the PDMS matrix, we obtain changes in σ up to 50% for fields of 400 mT and with resistances on the order of 1-10 Ω. Magnetoresistive and magnetoelastic properties make these materials very interesting for applications in flexible electronics, electronic skins, anisotropic pressure, and magnetic field sensors.     

局部化学法合成K0.5Bi0.5TiO3片状晶粒及其反应机理研究

以含铋层状Bi4Ti3O12(BIT)晶粒作为反应前驱体, 通过熔盐环境下的局部化学反应法制备了片状钛酸铋钾(K0.5Bi0.5TiO3, KBT)陶瓷粉体晶粒. 分析结果表明, 所制备的KBT陶瓷晶粒平均直径约为15～20 μm, 厚度小于2 μm. 分析了由含铋层状型BIT向钙钛矿型KBT片晶转化的形成机制, 并讨论了反应路径对最终产物形貌的影响规律.     

Synthesis and antibacterial study of 2-amino-4H-pyrans and pyrans annulated heterocycles catalyzed by sulfated polysaccharide-coated BaFe12O19 nanoparticles

Research on Chemical Intermediates - In this procedure, the synthesis of ecofriendly, magnetically retrievable BaFe12O19 was reported using a sulfated polysaccharide of algal origin, Irish...     

均匀共沉淀法制备BaTiO3 -Nix Zn1-x Fe2 O4 核-壳粒子及其性能

以尿素为沉淀剂, 在无后续热处理的情况下, 采用均匀共沉淀法制备了BaTiO3-NixZn1-xFe2O4核-壳粒子. 采用透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 能谱仪(EDS)及振动样品磁强计(VSM)对BaTiO3-NixZn1-xFe2O4核-壳粒子的形貌、 结构、 成分和磁性能进行了表征. 结果表明, 制备的核-壳结构粒子中NixZn1-xFe2O4壳层在BaTiO3颗粒的表面包覆完整. 通过控制共沉淀中NiCl2·6H2O与ZnCl2的摩尔比可以调控BaTiO3-NixZn1-xFe2O4核-壳粒子的磁性; 加入的NiCl2·6H2O与ZnCl2摩尔比为7∶3时制得的核-壳粒子具有较好的磁性能, 其饱和磁化强度和矫顽力分别为26.999 A·m2/kg和902.787 A/m.     

ANALYSIS AND CHARACTERIZATION OF MICROSCOPIC MORPHOLOGY AND ORIENTATION STRUCTURE OF POLYANILINE POLYMERIZED IN A CONSTANT MAGNETIC FIELD

Conductive polyaniline(PAn-_M and PAn-_O) doped with dodecylbenzene sulfonic acid(DBSA) was synthesized by using emulsion polymerization method in the presence of a constant magnetic field(0.4 T) and the absence of magnetic field, respectively.The effects of magnetic field on the microscopic morphology and orientation structure of PAn were generally analyzed and characterized by using transmission electron microscope(TEM),X-ray diffraction(XRD) and through the conductivity anisotropy of unit resistance o...     

掺杂对棒状纳米SrFe_(12)O_(19)形貌和性能的影响

以FeCl2为原料,利用化学沉淀法制备了针状纳米α-FeOOH中间体,并通过柠檬酸法在针状纳米α-FeOOH表面包裹锶的柠檬酸配合物,煅烧后形成的棒状纳米SrFe12O19并分别在共沉淀和溶胶-凝胶2个不同过程中对纳米SrFe12O19进行镧掺杂。采用XRD,TEM和振动样品磁强计(VSM)对SrFe12O19及掺杂锶铁氧体的结构、形貌及磁性能进行了表征。结果表明:沉淀法和柠檬酸法相结合后制得的针状前驱体于900℃煅烧后可制得平均直径为40nm,长径比为15～20的棒状纳米SrFe12O19。在沉淀过程中对前驱体进行掺杂后制得的SrLaxFe12-xO19较同温度时在溶胶-凝胶过程中进行掺杂制得样品的长径比有所增加,进而使得SrLaxFe12-xO19的各向异性变大,磁性能增加,且在沉淀过程中掺杂镧后,样品的矫顽力和饱和磁化强度达到最大值时,x值明显大于溶胶-凝胶过程中进行掺杂制得的棒状SrLaxFe12-xO19。利用共沉淀法掺杂后,当x=0.15时制备的样品的矫顽力最大为6179.1Oe,此时样品的饱和磁化强度和剩余磁化强度分别65.7和38.4emu·g-1。当x=0.2时制备的样品的饱和磁化强度达到最大值为67.3emu·g-1,样品的矫顽力为5852.7Oe。     

Assesment of dimethyl phthalate removal from aqueous phase using barium hexaferrite containing magnetic beads

The barium hexaferrite (BaFe(12)O(19)) containing magnetic poly (ethylene glycol dimethacrylate-vinyl pyridine; mag-poly [EGDMA-VP]) beads (average diameter=53-212 μm) were synthesized and characterized. Their use as an adsorbent in the removal of dimethyl phthalate (DMP) from an aqueous solution was investigated. The mag-poly (EGDMA-VP) beads were prepared by copolymerizing of 4-vinyl pyridine (VP) with ethylene glycol dimethacrylate (EGDMA). The mag-poly (EGDMA-VP) beads were characterized by N(2) adsorption/desorption isotherms (BET), vibrating sample magnetometer (VSM), X-ray powder diffraction (XRD), elemental analysis, scanning electron microscope (SEM), and swelling studies. At a fixed solid/solution ratio, the various factors affecting the adsorption of DMP from aqueous solutions such as pH, initial concentration, contact time, and temperature were analyzed. The maximum DMP adsorption capacity of the mag-poly (EGDMA-VP) beads was determined as 96.2 mg/g at pH 3.0, 25 °C. All the isotherm data can be fitted with both the Langmuir and the Dubinin-Radushkevich isotherm models. The pseudo-first-order, pseudo-second-order, Ritch-second-order, and intraparticle diffusion models were used to describe the adsorption kinetics. The thermodynamic parameters obtained indicated the exothermic nature of the adsorption. The DMP adsorption capacity did not change after 10 batch successive reactions, demonstrating the usefulness of the magnetic beads in applications.     

恒定磁场(0.4 T)对聚苯胺微观取向结构的影响

在恒定磁场(0.4 T)条件下, 采用乳液聚合法合成了十二烷基苯磺酸掺杂聚苯胺(PAn), 并通过透射电子显微镜(TEM)、X射线衍射(XRD)、傅立叶红外光谱(FT-IR)、电导率、产物复合膜电阻率的各向异性, 以及产物间甲酚(m-cresol)溶液的电导率在外电场作用下变化的分析与表征, 系统研究了磁场对PAn的微观取向结构及其性能的影响. 实验结果表明, 与无磁场条件下制备的聚苯胺(PAn_-O)相比, 磁场条件下制备的聚苯胺(PAn_-M)具有更高的结晶度和明显的微观取向结构, 其微粒有序排列和堆砌成了许多具有一定长/径比的条状聚集体; PAn_-M/PVA(聚乙烯醇)复合膜经磁化成膜, 可以表现出明显的导电性能的各向异性; PAn_-M/m-cresol溶液的电导率, 在有、无外场(电场)作用下存在明显的突变. 分析认为: 由于磁场条件下制备的PAn粉末存在着微观取向和显著的抗磁磁化率的各向异性, 在外磁场作用下其堆砌方式会进一步演变成宏观的取向, 随之表现出物理性能上的各向异性.