(Liquid + liquid) equilibria of three ternary systems: (heptane + benzene + N-formylmorpholine), (heptane + toluene + N-formylmorpholine), (heptane + xylene + N-formylmorpholine) from T = (298.15 to 353.15) K

(Liquid + liquid) equilibrium (LLE) data for ternary systems: (heptane + benzene + N-formylmorpholine), (heptane + toluene + N-formylmorpholine), and (heptane + xylene + N-formylmorpholine) have been determined experimentally at temperatures ranging from 298.15 K to 353.15 K. Complete phase diagrams were obtained by determining solubility and tie-line data. Tie-line compositions were correlated by Othmer–Tobias and Bachman methods. The universal quasichemical activity coefficient (UNIQUAC) and the non-random two liquids equation (NRTL) were used to predict the phase equilibrium in the system using the interaction parameters determined from experimental data. It is found that UNIQUAC and NRTL used for LLE could provide a good correlation. Distribution coefficients, separation factors, and selectivity were evaluated for the immiscibility region.     

(Liquid + liquid) equilibrium for the system {ethyl stearate(1) + ethanol(2) + glycerol(3)}

This paper reports the results of a new experimental study on the (liquid + liquid) equilibrium of the system {ethyl stearate(1) + ethanol(2) + glycerol(3)} at atmospheric pressure and at T = (313.15 and 323.15) K. The equilibrium compositions were measured by gas chromatography. Ternary diagrams were obtained for each temperature and the equilibrium data were compared to the system in the presence of salt (NaCl) at T = 323.15 K. The experimentally determined (liquid + liquid) equilibrium data were satisfactorily correlated with NRTL and UNIQUAC equations. A comparative analysis was performed using the UNIFAC-LLE group contribution method. From the results presented herein good predictions were obtained for this ternary system.     

(Solid + liquid) equilibria of (naphthalene + isomeric dichlorobenzenes)

(Solid + liquid) equilibria (SLE) have been measured for naphthalene + o-dichlorobenzene, + m-dichlorobenzene, and + p-dichlorobenzene using differential scanning calorimetry (DSC) over the whole concentration range. It was found that the phase diagram of (naphthalene + m-dichlorobenzene) is of a simple eutectic type with the eutectic point at 244.85 K and 0.058 mole fraction of naphthalene, the phase diagram of (naphthalene + p-dichlorobenzene) is of a simple eutectic type with the eutectic point at 302.85 K and 0.390 mole fraction of naphthalene and in the system of (naphthalene + o-dichlorobenzene), a 1:1 incongruently melting compound is formed and that the phase diagram show a eutectic and a peritectic, the eutectic point is at 232.55 K and 0.130 mole fraction of naphthalene, the peritectic point at 250.15 K and 0.077 mole fraction of naphthalene. Furthermore, the activity coefficients of components in mixtures of (naphthalene + m-dichlorobenzene) and (naphthalene + p-dichlorobenzene) have been correlated by the Scatchard–Hildebrand solubility parameter expression. This approach offers a useful procedure for estimating with good accuracy.     

High-pressure (vapor + liquid) equilibria in the (nitrogen + n-heptane) system

In this work, new (vapor + liquid) equilibrium data for the (N₂ + n-heptane) system were experimentally measured over a wide temperature range from (313.6 to 523.7) K and pressures up to 50 MPa. A static-analytic apparatus with visual sapphire windows and pneumatic capillary samplers was used in the experimental measurements. Equilibrium phase compositions and (vapor + liquid) equilibrium ratios are reported. The new results were compared with those reported by other authors. The comparison showed that the pressure–composition data reported in this work are less scattered than those determined by others. Hence, the results demonstrate the reliability of the experimental apparatus at high temperatures and pressures. The experimental data were represented with the PR and PC-SAFT equations of state by using one-fluid mixing rules and a single temperature independent interaction parameter. Results of the representation showed that the PC-SAFT equation was superior to the PR equation in correlating the experimental data of the (N₂ + n-heptane) system.     

(Liquid + liquid) equilibria of the (water + butyric acid + dodecanol) ternary system

(Liquid + liquid) equilibrium (LLE) data for the (water + butyric acid + dodecanol) ternary system have been determined experimentally at T = (298.2, 308.2 and 318.2) K. Complete phase diagrams were obtained by determining binodal curves and tie lines. The reliability of the experimental tie lines was confirmed by using the Othmer–Tobias correlation. The UNIFAC method was used to predict the phase equilibrium in the ternary system using the interaction parameters determined from experimental data of CH₃, CH₂, COOH, OH and H₂O functional groups. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) phase equilibria for (water + 2,3-butanediol + oleyl alcohol) at T = (300.2, 307.2, and 314.2) K

(Liquid + liquid equilibrium) (LLE) data for ternary system: (water + 2,3-butanediol + oleyl alcohol) has been measured at T = (300.2, 307.2, and 314.2) K. Complete phase diagrams were obtained by determining solubility and tie-line data. Tie-line compositions were correlated by Othmer–Tobias and Bachman methods. The nonrandom two liquids equation (NRTL) was used to correlate the phase equilibrium in the system using the interaction parameters determined from experimental data. It is found that NRTL could give a good correlation for the LLE data. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

Thermodynamic study of the system (LiCl + LiNO3 + H2O)

The solubility of the binary system (LiNO₃ + H₂O) from T = 273.15 K to T = 333.15 K and solubility isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were elaborately measured at T = 273.15 K and T = 323.15 K. These solubility data, as well as water activities in the binary systems from the literature, were treated by an empirically modified BET model. The isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were reproduced and a complete phase diagram of the ternary system in the temperature range from 273.15 K to 323.15 K predicted. It is shown that the solubility data for the binary system (LiNO₃ + H₂O) measured in this work are slightly different from the literature data. Simulated results showed that the saturated salt solution of (2.8LiCl + LiNO₃) is in equilibrium with the stable solid phase LiNO₃(s) over the temperature range from 283.15 K to 323.15 K, other than the solid phases LiNO₃ · 3H₂O(s) and LiClH₂O(s) as reported by Iyoki et al. [S. Iwasaki, Y. Kuriyama. T. Uemura, J. Chem. Eng. Data 38 (1993) 396–398].     

(Liquid + liquid) equilibria of (sulfolane + benzene + n-hexane), (N-formylmorpholine + benzene + n-hexane), and (sulfolane + N-formylmorpholine + benzene + n-hexane) at temperatures ranging from (298.15 to 318.15) K: Experimental results and correlation

The experimental (liquid + liquid) equilibrium (LLE) properties for two ternary systems containing (N-formylmorpholine + benzene + n-hexane), (sulfolane + benzene + n-hexane) and a quaternary mixed solvent system (sulfolane + N-formylmorpholine + benzene + n-hexane) were measured at temperature ranging from (298.15 to 318.15) K and at an atmospheric pressure. The experimental distribution coefficients and selectivity factors are presented to evaluate the efficiency of the solvents for extraction of benzene from n-hexane. The LLE results obtained indicate that increasing temperature decreases selectivity for all solvents. The LLE results for the systems studied were used to obtain binary interaction parameters in the UNIQUAC model by minimizing the root mean square deviations (RMSD) between the experimental and calculated results. Using the interaction parameters obtained, the phase equilibria in the systems were calculated and plotted. The calculated compositions based on the UNIQUAC model were found to be in good agreement with the experimental values. The result of the RMSD obtained by comparing the calculated and experimental two-phase compositions is 0.0163 for (N-formylmorpholine + benzene + n-hexane) system and is 0.0120 for (sulfolane + benzene + n-hexane) system.     

(Vapour + liquid) equilibrium data for the azeotropic {1,1-difluoroethane (R152a) + 1,1,2,2-Tetrafluoroethane (R134)} system at various temperatures from (258.150 to 288.150) K

(Vapour + liquid) equilibrium (VLE) data for the {1,1-difluoroethane (R152a) + 1,1,2,2-Tetrafluoroethane (R134)} system were measured at T = (258.150 to 288.150) K. The experiment is based on a static–analytic method. Experimental data were correlated with the Peng–Robinson equation of state (PR EoS) and the Huron–Vidal (HV) mixing rule involving the NRTL activity coefficient model. The results show good agreement with experimental results for the binary system at each temperature. It was found that the system has a negative azeotropic behaviour within the temperature range measured here.     

Phase equilibrium data for the ternary system (propane + chloroform + oryzanol)

The compound oryzanol available in the rice bran (oriza sativa) is well known for its antioxidant activity. Phase equilibrium data involving oryzanol in compressed fluids, hardly found in the literature, are important to provide the basis for the extraction and fractionation processes. In this sense, the aim of this work is to report phase equilibrium measurements for the system (γ-oryzanol + chloroform) in compressed propane. Phase equilibrium experiments were performed using the static synthetic method (cloud points transition data) in a high-pressure variable-volume view cell in the temperature range of 303 K to 353 K, pressures up to 17 MPa, for oryzanol overall mass fractions of 2 wt%, 5 wt% and 10 wt% in (propane + chloroform) mixtures. A complex phase behaviour comprising vapour–liquid, liquid–liquid, vapour–liquid–liquid, solid–liquid, solid–liquid–liquid, solid–liquid–liquid–vapour transitions were visually observed for the system studied.     

(Liquid + liquid) equilibria of (water + butyric acid + esters) ternary systems

(Liquid + liquid) equilibrium (LLE) data of the solubility (binodal) curves and tie-line end compositions were examined for mixtures of {water (1) + butyric acid (2) + ethyl propionate or dimethyl phthalate or dibutyl phthalate (3)} at T = 298.15 K and (101.3 ± 0.7) kPa. The relative mutual solubility of the butyric acid is higher in the layers of esters than in the aqueous layer. The reliability of the experimental tie-line data was confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems were predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

Study of bromide salts solubility in the (m1NaBr + m2MgBr2)(aq) system at T = 323.15 K. Thermodynamic model of solution behavior and (solid + liquid) equilibria in the (Na + K + Mg + Br + H2O) system to high concentration and temperature

The bromide minerals solubility in the mixed system (m₁NaBr + m₂MgBr₂)(aq) have been investigated at T = 323.15 K by the physico-chemical analysis method. The equilibrium crystallization of NaBr·2H₂O(cr), NaBr(cr), and MgBr₂·6H₂O(cr) has been established. The solubility-measurements results obtained have been combined with all other experimental equilibrium solubility data available in literature at T = (273.15 and 298.15) K to construct a chemical model that calculates (solid + liquid) equilibria in the mixed system (m₁NaBr + m₂MgBr₂)(aq). The solubility modeling approach based on fundamental Pitzer specific interaction equations is employed. The model gives a very good agreement with bromide salts equilibrium solubility data. Temperature extrapolation of the mixed system model provides reasonable mineral solubility at high temperature (up to 100 °C). This model expands the previously published temperature variable sodium–potassium–bromide and potassium–magnesium–bromide models by evaluating sodium–magnesium mixing parameters. The resulting model for quaternary system (Na + K + Mg + Br + H₂O) is validated by comparing solubility predictions with those given in literature, and not used in the parameterization process. Limitations of the mixed solution models due to data insufficiencies at high temperature are discussed.     

(Liquid + liquid) equilibria of (water + butyric acid + dibasic esters) ternary systems

(Liquid + liquid) equilibrium (LLE) data of the solubility (binodal) curves and tie-line end compositions were examined for mixtures of {water (1) + butyric acid (2) + dimethyl succinate or dimethyl glutarate or dimethyl adipate (3)} at T = 298.15 K and p = (101.3 ± 0.7) kPa. The relative mutual solubility of the butyric acid is higher in the dibasic esters layers than in the aqueous layer. The reliability of the experimental tie-line data was confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems were predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

Phase equilibrium measurements of (methane + benzene) and (methane + methylbenzene) at temperatures from (188 to 348) K and pressures to 13 MPa

New isothermal pTxy data are reported for (methane + benzene) and (methane + methylbenzene (toluene)) at pressures up to 13 MPa over the temperature range (188 to 313) K using a custom-built (vapor + liquid) equilibrium (VLE) apparatus. The aim of this work was to investigate literature data inconsistencies and to extend the measurements to lower temperatures. For (methane (1) + benzene (2)), measurements were made along six isotherms from (233 to 348) K at pressures to 9.6 MPa. At temperatures below 279 K there was evidence of a solid phase, and thus only vapor phase samples were analyzed at these temperatures. For the (methane (1) + methylbenzene (3)) system, measurements were made along seven isotherms from T = (188 to 313) K at pressures up to 13 MPa. Along the 198 K isotherm, a significant change in the data’s p,x slope was observed indicating (liquid + liquid) equilibria at higher pressures. The data were compared with literature data and with calculations made using the Peng–Robinson (PR) equation of state (EOS). For both binary systems our data agree with much of the literature data that also deviate from the EOS in a similar manner. However, the data of Elbishlawi and Spencer (1951) for both binary systems, which appear to have received an equal weighting to other data in the EOS development, are inconsistent with the results of our measurements and data from other literature sources.     

(Liquid + liquid) equilibria for (benzene + cyclohexane + dimethyl sulfoxide) system at T = (298.15 or 303.15) K: Experimental data and correlation

(Liquid + liquid) equilibrium (LLE) data were measured experimentally at T = (298.15 or 303.15) K and atmospheric pressure for the (benzene + cyclohexane + dimethyl sulfone (DMSO)) system. The Othmer–Tobias equation was applied to verify the reliability of the data. Based on the data, the selectivity of DMSO was estimated and compared with that of ionic liquids. The highest selectivity coefficient of DMSO can reach beyond 14, which means it is able to compete with some ionic liquids and it would be a good extractant to separate benzene from cyclohexane. At the same time, the NRTL model was used to correlate the data and the results show that the model agrees on the experimental data very well.     

(Liquid + liquid) equilibria of (water + propionic acid + dibasic esters) ternary systems

(Liquid + liquid) equilibrium (LLE) data for the solubility curves and tie-line compositions were examined for mixtures of {water (1) + propionic acid (2) + dimethyl succinate or dimethyl glutarate or dimethyl adipate (3)} at T = 298.15 K and atmospheric pressure, (101.3 ± 0.7) kPa. The relative mutual solubility of the propionic acid is higher in the dibasic esters phases than in the aqueous phase. The reliability of the experimental tie-line data were confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems were predicted by UNIFAC and modified UNIFAC methods. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

Isobaric (vapour + liquid + liquid) equilibrium data for (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) systems at 100 kPa

Isobaric (vapour + liquid + liquid) equilibria were measured for the (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) system at 100 kPa.The apparatus used for the determination of (vapour + liquid + liquid) equilibrium data was an all-glass dynamic recirculating still with an ultrasonic homogenizer couple to the boiling flask.The experimental data demonstrated the existence of a heterogeneous ternary azeotrope for both ternary systems. The (vapour + liquid + liquid) equilibria data were found to be thermodynamically consistent for both systems.The experimental data were compared with the estimation using UNIQUAC and NRTL models and the prediction of UNIFAC model.     

(Liquid + liquid) equilibria for (water + 1-propanol + diisopropyl ether + octane,or methylbenzene,or heptane) systems at T = 298.15 K

(Liquid + liquid) equilibria (LLE) data were presented for one ternary system of {water + octane + diisopropyl ether (DIPE)} and three quaternary systems of (water + 1-propanol + DIPE + octane, or methylbenzene, or heptane) at T = 298.15 K and p = 100 kPa. The experimental LLE data were correlated with the modified and extended UNIQUAC models. Distribution coefficients were derived from the experimental LLE data to evaluate the solubility behavior of components in organic and aqueous phases.     

(Liquid + liquid) equilibria of (water + ethanol + dimethyl glutarate) at several temperatures

(Liquid + liquid) equilibrium (LLE) data of (water + ethanol + dimethyl glutarate) have been determined experimentally at T=(298.15,308.15 and 318.15) K. The reliability of the experimental tie-line data was ascertained by using the Othmer and Tobias correlation. The LLE data of the ternary mixture were predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) equilibrium of (water + 2-propanol + 1-butanol + salt) systems at T = 313.15 K and T = 353.15 K: Experimental data and correlation

(Liquid + liquid) equilibrium data for the quaternary systems (water + 2-propanol + 1-butanol + potassium bromide) and (water + 2-propanol + 1-butanol + magnesium chloride) were measured at T = 313.15 K and T = 353.15 K. The overall salt concentrations were 5 and 10 mass percent. Ternary (liquid + liquid) equilibrium data for the salt-free system (water + 2-propanol + 1-butanol) were also determined and found to be in good agreement with data from the literature. The NRTL model for the activity coefficient was used to correlate the data. New interaction parameters were estimated, using the Simplex minimization method and a concentration-based objective function. The results are very satisfactory, with root mean square deviations between experimental and calculated compositions of both phases being less than 0.5%.