Application of Differential UV Spectroscopy to the Determination of Lignin Substances in Polluted Water

The absorption spectra of Bjorkman lignin, lignin sulfate, lignosulfonates, and humic substances in neutral and alkaline media are considered. It was found that the difference spectra of lignins (an alkaline solution with reference to a neutral solution) exhibited several intense bands, whereas humic substances exhibited equal shifts of the spectra over the entire spectral range. This distinctive property of the difference spectra of lignin substances, as compared to the spectra of humic substances, can be used for determining lignins in polluted water.     

Determination of aromatic sulfonates in the river Elbe by on-line ion-pair extraction and ion-pair chromatography

An automated method based on ion-pair extraction and HPLC has been used to investigate the occurrence of aromatic sulfonates in the river Elbe. Twelve different naphthalene, anthraquinone and stilbene sulfonates have been found. The substances have been detected by UV detection at 220 nm and, if possible, by their fluorescence signal. The aromatic sulfonates have been identified by their retention time and by comparing their UV spectra with the respective spectra of reference substances. The occurrence of these substances in the river Elbe water is caused by a discharge of several waste water effluents. The results showed, that certain naphthalene sulfonates cannot be totally removed by biological treatment and adsorption on activated carbon.     

Influence of the presence of surfactants and humic acid in waters on the indophenol-type reaction method for ammonium determination

This work has evaluated the influence of humic acid and/or surfactants in the quantification of ammonium in waters with the indophenol-type reaction method. Thymol has been employed with the colorimetric method for sample ammonium concentrations between 0.25 and 1 mg L⁻¹. In addition, SPE/diffuse reflectance method has been used for quantification of ammonium at low concentrations (between 0.025 and 0.25 mg L⁻¹). Matrix effect owing to humic substances were observed with the colorimetric method when the concentration was equal or higher than 25 mg L⁻¹. Lower concentrations of humic compounds produced matrix effects with the more sensitive SPE/diffuse reflectance method. Generalized H-point standard addition method (GHPSAM) was employed for evaluating the effect of humic acids and for eliminating the bias error produced by humic acids. Real water samples of different types were analyzed and accurate results for ammonium concentration were obtained with both procedures in presence or absence of humic acids. Cationic and anionic surfactants inhibited the derivatization reaction at percentages up to 0.001% and 0.5%, respectively, and non-ionic surfactants at percentages of 5.5%     

High-performance liquid chromatographic determination of humic acid in environmental samples at the nanogram level using fluorescence detection

A high-performance liquid chromatographic method for the determination of humic acid in environmental samples is presented. The humic acid is chromatographed as its sodium or calcium complex, eluting as a single, sharp peak. Coral skeletal matter, sea water, river water, soils and plant matter were successfully analysed. The detection limit is 15 ng. The relative standard deviation for a coral skeletal sample is 1.9%. Unusual chromatographic properties such as the occurrence of peak broadening with increased concentration appear to be due to a slow change in the equilibrium composition of humic acid. In solution, fulvic acid showed similar properties to humic acid.     

Use of disposable clean-up columns for selective removal of humic substances prior to measurements with a nitrate ion-selective electrode

Measurements of nitrate in natural waters with a nitrate ion-selective electrode are seriously affected by the presence of humic substances. These can be removed quantitatively by a clean-up procedure with cheap disposable adsorption columns packed with chemically-bonded alkylamino silica. The method is applied to natural water samples with high contents of humic substances. The nitrate concentrations found were in good agreement with determination by ion chromatography.     

Spurenanalyse von huminstoffen im trinkwasser: The d.c. polarographic determination of traces of humic substances in potable waters

(The d.c. polarographic determination of traces of humic substances in potable waters) The inhibiting effect of a tri-n-butylphosphate layer adsorbed at the mercury drop on the polarographic wave of copper(II) is reduced by humic substances. This effect can be utilized to determine humic substances in the range 0.05–1 mg l^-1. The standard substance used was isolated from peaty water. Humic and fulvic acids are not differentiated but amino acids, peptides and polyhydroxy compounds do not interfere.     

A modified nitroso-r method for the determination of cobalt in sea water

The existing colorimetric nitroso-R method for the determination of biologically important cobalt in sea water described by Thompson and Laevastu has been studied in detail, modified and improved. A procedure is recommended in which an approximately five-fold increase in sensitivity is achieved in the measurement of the nitroso-R chelate through close control of : pH, development time of complex, conditions for decomposition of excess reagent, and employment of a wavelength of 425 mμ. The size of the water sample required for an analysis is reduced from 10 to 21. For optimum results it was found necessary for a minimum period of 7 days to elapse following precipitation with sodium carbonate prior to filtration and analysis. A previously unreported salt effect in the procedure is described which requires either construction of a calibration curve from sea water spiked with cobalt or a correction in use of standards in distilled water.A precision was obtained with a 1–2% relative standard deviation throughout range of concentrations used, with an accuracy of 3.0% at 0.5 p.p.b.     

A solid-phase extraction procedure for the clean-up of thiram from aqueous solutions containing high concentrations of humic substances

A simple solid-phase extraction (SPE) procedure with an octadecyl bonded phase silica (C₁₈) was developed for clean-up of the fungicide thiram from aqueous solutions containing high concentrations of humic substances, for future studies of thiram adsorption onto solid humic substances or soils. Suspensions of humic acids and soil, in aqueous 0.01 M CaCl₂ solution, were prepared and used as samples. These extracts were spiked with thiram and immediately applied to a C₁₈-SPE cartridge. Thiram was eluted with chloroform and its concentration measured by spectrophotometry at 283 nm. Non-spiked aqueous extracts (blanks) and a control sample of thiram in 0.01 M CaCl₂ aqueous solution were also prepared and submitted to the same SPE procedure. The results show that humic substances are extensively retained by the C₁₈ cartridge but are not eluted with CHCl₃. Recoveries of 100-104% were obtained for thiram in the presence of humic substances. The SPE procedure described in this work is an efficient clean-up step to remove the interference of humic substances absorbance and to be coupled to any spectrophotometric or HPLC-UV method, usually used for thiram analysis in food extracts.     

Capillary electrophoretic separation of humic substances using hydroxyethyl cellulose as a buffer additive and its application to characterization of humic substances in a river water sample

We have developed a concise tool for the investigation of the transition of humic substances in environmental water. The separation of water-soluble humic substances was achieved rapidly and effectively by capillary electrophoresis using a polyacrylamide-coated capillary and a phosphate electrophoretic buffer solution (pH 7.0) containing hydroxyethyl cellulose. The separation mechanism was assessed using the ultrafiltration technique. The effect of the complexation of humic substances with metal ions was studied by using the proposed method. When Fe(III) ions or EDTA was added to the sample solution of fulvic acid, a distinct change in the electropherogram pattern based on the conformational change of fulvic acid was observed. The successful application of the proposed method to the characterization of humic substances in a river water sample was also demonstrated. Figure Addition of Fe(III) ions or EDTA to a solution containing fulvic acid (FA) results in a distinct change in the electropherogram pattern, which reflects the conformational change of FA: this forms the basis for the characterization of humic substances in river water samples     

The determination of bromide in natural waters by flow injection analysis

Bromide can occur in well waters as a result of sea water intrusion. The phenol red method is adapted to a flow-injection system and interferences are studied by using a two-channel valve. Standards are injected from one loop of the valve while the possible interferent is injected from the other loop; this provides a fast means of evaluating interferences. Ammonia, cyanide and humic substances interfere. Bromide can be determined down to 2 μM at a rate of 80 samples per hour     

Determination of aromatic sulfonates in coastal water by on-line Ion-pair solid-phase extraction/ion-pair liquid chromatography with UV detection

Summary A method for determining aromatic sulfonates in sea water is presented. Ion-pair solid phase extraction is coupled on-line to ion-pair liquid chromatography with UV detection. In the enrichment step, the recoveries from 100 mL of sea water were higher than 65% for most analytes. Linearity was good and detection limits were between 0.02 and 1 μgL⁻¹. The repeatability of the method, expressed as % of relative standard deviation (n=3) was between 1 and 15%. The method was checked in coastal water near the commercial port of Tarragona, where effluents from the petrochemical industry are discharged. All the samples taken were found to contain 2-naphthalenesulfonate.     

Association of Am with humic substances isolated from river waters with different water quality

The association properties of Am with aquatic humic substances in a 0.01M NaClO₄ solution at pH 6-8 were studied on the basis of molecular size distribution. Ten humic substances isolated from river water with different water quality (pH 3.9-8.0 and dissolved organic carbon (DOC) concentration of 2-40 mg/l) were used for comparing their effects on the association of Am. The molecular size distribution of Am in the presence of humic substances from an uncolored river water (DOC 2 mg/l) was different from that at the experimental systems using humic substances from brownish and high DOC (14-40 mg/l) river waters.     

The determination of rubidium by the method of stable isotope dilution

The rubidium contents of a granite (G-1), a diabase (W-1) and sea-water have been determined by mass spectrometric isotope dilution analysis. The values found are: G-1, 214 p.p.m-; W-1, 21.3 p.p.m.; sea water, 121.4 μg/l. These results show excellent agreement with values obtained at Harwell by neutron activation analysis, and the coefficient of variation for four determinations is usually ±1–2%.Rubidium ions were produced in the mass spectrometer by either a side filament or a centre filament technique. The former method enables rubidium and lithium determinations to be combined; the results obtained by the second method suggest that concentrations of the order of 1 p.p.m. may be determined for a sample of only a few mg with little chemical treatment beyond that required to decompose the sample.     

The conformational dynamics of humic polyanions in model organic and organo-mineral aggregates

Molecular mechanics calculations and simulated annealing were applied to model humic polyanions originating from lignin. The dynamic behavior of such oxidized lignins in model soil organic complexes, such as an oxidized lignin-carbohydrate complex (LCC) and humic (oxidized LCC)-clay aggregates, was analyzed. Neither ionization nor hydrogen bonding bring significant changes in the conformational properties of oxidized lignin and LCC. Oxidized lignin and LCC oligomers (humic substances in soil) bind to the mineral surfaces, a process that was exemplified in computational experiments on complexes with muscovite. Upon ionization, a lignin-derived oligomer develops strong attractive organo-mineral interactions through cation bridges. Without metal cations, electrostatic repulsion between negatively charged anions and the oxygen-mineral surface prevails, and the two parts of the organo-mineral complex drift apart. This tendency is typical of an oxidized lignin oligomer but not of a topological oxidized LCC.     

Chemical removal of humic substances interfering with the on-line solid-phase extraction—Liquid chromatographic determination of polar water pollutants

Summary Different methods for removing interference by humic substances in the analysis of polar pollutants have been compared in the analysis of environmental water by solid-phase extraction (SPE) with a chemically modified polymeric resin coupled on-line to liquid chromatography with UV detection. The methods were based on the use of chemical reagents. The best method was found to be addition of sodium sulphite to humic-containing water before SPE. The appropriate amount of sulphite depends on the amount of humic substances dissolved in the sample—for analysis of 50 mL tap and Ebro river water, respectively, 250 μL and 500 μL 10 % Na₂SO₃ solution had to be added. In both cases, the recovery values after chemical treatment were similar to those when a Milli-Q-quality water standard was analysed.     

Analysis of humic acid fouling during microfiltration using a pore blockage–cake filtration model

Fouling by natural organic matter, such as humic substances, is a major factor limiting the use of microfiltration for water purification. The objective of this study was to develop a fundamental understanding of the underlying mechanisms governing humic acid fouling during microfiltration using a combined pore blockage–cake filtration model. Data were obtained over a range of humic acid concentrations, transmembrane pressures, and stirring speeds. The initial flux decline was due to pore blockage caused by the deposition of large humic acid aggregates on the membrane surface, with a humic acid deposit developing over those regions of the membrane that have first been blocked by an aggregate. The rate of cake growth approaches zero at a finite filtrate flux, similar to the critical flux concept developed for colloidal filtration. The data were in good agreement with model calculations, with the parameter values providing important insights into the mechanisms governing humic acid fouling during microfiltration. In addition, the basic approach provides a framework that can be used to analyze humic acid fouling under different conditions.     

Pyrolysis-GC-FTIR for structural elucidation of aquatic humic substances

Substructure components of various aquatic humic substances were investigated by a coupled pyrolysis — gas chromatography — Fourier-transform infrared spectroscopy (Py-GC-FTIR) procedure. The humic substances studied gave similar pyrolysis products, but in varying proportions. Many of the pyrolysis products (e.g. methanol, acetone, alkylbenzenes, cyclopentane, aliphatic and aromatic organic acids, acetamide, pyrrole and phenols) could be identified by their FTIR spectra using a digital library for automatic comparison. Some of the compounds are related to lignin fragments which form a large part of the humic substances investigated. Other products give hints to the involvement of tetrapyrroles, fatty acids, furanoses and amino compounds in the structure of humic macromolecules.Dedicated to Professor Dr. Dieter Klockow on the occasion of his 60th birthday     

Electron microscopy of submicron particles in natural waters—Detection of organic substances

Submicron particles, 0.1–1 m in diameter, in pond water were collected on a 10–20 nm thick carbon film mounted on a carbon coated nylon grid by centrifugation and exposed to osmium(VIII) oxide vapor at room temperature for 2 h. Organic substances reacted with the reagent, while alumino-silicates and hydrated iron(III) oxide as well as the carbon film did not. The X-ray image of osmium revealed that organic substances, presumably humic substances, were associated with most of the particles, especially with hydrated iron (III) oxide, in the pond water.     

Metal-modified silica adsorbents for removal of humic substances in water

As novel adsorbents for humic substances, Fe-, Mg-, and Ca-modified silica gels SiO(2)Fe, SiO(2)Mg, and SiO(2)Ca were prepared, and their adsorbabilities to humic and fulvic acids were evaluated in water at 25 degrees C for 20 h. Among these adsorbents, SiO(2)Fe indicated the highest adsorbability, in which removing humic substances in water was accomplished to 80-97%. By calcination at 600 degrees C and washing with water, adsorbabilities of the silica adsorbents deteriorated except for the case of calcination of SiO(2)Ca. This is due to changing metal modification structures and losing chlorine, judging from elemental analysis, TG-DTA, and XPS. Especially, the modifier Fe was tightly fixed on the silica surface of SiO(2)Fe, since the metal content was almost constant even after the calcination and water washing unlike the other adsorbents. Therefore, we found that SiO(2)Fe is the most useful adsorbent among the silica adsorbents and that its modification structure is composed of SiOFe, FeCl, and FeOH. In addition, the adsorption mechanism is explained by an interaction between Fe and humic substance molecule having carboxylate and phenolate groups, accompanied with anion exchange of chloride ion Cl(-) for the humic substance molecule via the silica pores. SiO(2)Fe may be applied to an adsorbent alternative for charcoal in water purification plants, and the used SiO(2)Fe may be further reused as a fertilizer since humic substances have plant-glowing ability and silica strengthens plant parts.