Spectroscopic studies of thermal treatment effect on the composition and size of CdS1−xSex nanocrystals in borosilicate glass

The effect of heat treatment parameters on the chemical composition and average size of CdS_1−xSe_x nanocrystals obtained in borosilicate glass by diffusion-limited growth is studied by optical absorption and Raman scattering spectroscopy. An increase of selenium content from 0.75 to 0.83 in the nanocrystals with the heat treatment temperature and duration is observed. Three lowest-energy optical transitions in CdS_1−xSe_x nanocrystals are assigned to corresponding electronic transitions based on the observed dependence of the confinement-related absorption maxima on the nanocrystal size.     

Photoluminescence studies of Cd1−xZnxS nanocrystals

Cd_1−xZn_xS (0?x?0.5) nanocrystals have been synthesized using a simple chemical precipitation method. Morphological and crystallographic analyses have been done using transmission electron microscope (TEM) and X-ray diffraction (XRD). Room temperature energy and time resolved photoluminescence spectra of these synthesized nanophosphors have been studied using xenon lamp spectroflourometer and high peak power, pulsed N₂-laser excitation, respectively. Photoluminescence spectra are composed of broad peaks ranging from green to red region of the visible spectrum. Important optical parameters: excited state lifetime, trap-depth and decay constant values have been calculated from recorded luminescence decay curves. These nanophosphors show typical lifetime shortening and high quantum yield with increasing concentration of Zn.     

Transmission electron microscopy study of large field induced anisotropy (Co1−xFex)89Zr7B4 nanocomposite ribbons with dilute Fe-contents

Electron microscopy was employed to investigate the structure of magnetic field crystallized (Co_1−xFe_x)₈₉Zr₇B₄ alloys with only dilute Fe-contents (x=0, 0.025, 0.05, and 0.10). The x=0.025 and 0.05 alloys exhibit very large field induced anisotropies and multiple nanocrystalline phases (BCC, FCC, and HCP) surrounded by an intergranular amorphous phase. Correlation between the volume fraction crystallized and the measured value of H_K suggests that the large K_U values are associated with the crystalline phases that form. Multiple crystalline phases are present for the highest K_U alloys and so the presence of FCC and/or HCP-type nanocrystals may be responsible for these observations. High-resolution transmission electron microscopy (HRTEM) illustrates a number of microstructural features including (1) high densities of stacking faults in many of the FCC and, in particular, the HCP-type nanocrystals, (2) infrequent BCC/FCC orientation relationships, and (3) nanocrystals with disordered or long period stacking sequences of close-packed planes. High densities of planar faults are suggested as a potential source of K_U for the FCC and HCP-type nanocrystals, but the origin of the large values of K_U found in dilute Fe-containing, Co-rich “nanocomposite” alloys is an area where further work is needed.     

Intrinsic paramagnetic defects probe superionic phase transition in Ag1−xCuxI (x=0, 0.05, 0.15 and 0.50) nanocrystals

EPR probed the zincblende (γ) to cubic (α) AgI structural phase transition in AgI at 423 K through two intrinsic paramagnetic centers: an Ag²⁺-based hole center (signal ‘A’) and an Ag⁰-based conduction electron center (signal ‘B’) associated with AgI nanocrystallites. Sudden drops in intensity (I_PP), <g>, and ΔH_PP observed at 423 K for pure AgI nanocrystals. Addition of Cu in AgI increases the thermal stability of the cation sublattice as seen from the increase in the transition temperature from 423 K (undoped AgI) to 453 K. Abrupt jumps in the number of spins (N) and reciprocal susceptibility (1/χ) observed at increased phase transition temperatures in Cu-substituted AgI relative to that in undoped AgI reflects progressively strengthened local bonding configuration of γ-AgI structure induced by Cu.     

Ferromagnetic semiconductor Ge1−x−ySnxMnyTe with phase transformation of ferroelectric type

It is expected that joint existence of ferromagnetic properties and ferroelectric structural phase transition in diluted magnetic semiconductors IV-VI leads to new possibilities of these materials. Temperature of ferroelectric transition for such crystals can be tuned by the change of Sn/Ge ratio. Magnetic susceptibility, Hall effect, resistivity and thermoelectric power of Ge_1−x−ySn_xMn_yTe single crystals grown by Bridgeman method (x=0.083-0.115; y=0.025-0.124) were investigated within 4.2-300 K. An existence of FM ordering at T_C∼50 K probably due to indirect exchange interaction between Mn ions via degenerated hole gas was revealed. A divergence of magnetic moment temperature dependences at T?T_C in field-cooled and zero-field-cooled regimes is obliged to magnetic clusters which are responsible for superparamagnetism at T>T_C≈T_f (freezing temperature) and become ferromagnetic at T_C arranging spin glass state at T<T_f≈T_C. Phase transition of ferroelectric type at T≈46 K was revealed. Anomalous Hall effect which allows to determine magnetic moment was observed.     

Structural and magnetic properties of SmCo7−xMox alloys

Phase structure and magnetic properties of the as-cast and as-milled/annealed SmCo_7−xMo_x (x=0, 0.1, 0.2, 0.3, 0.4) alloys have been systematically studied. It is found that all the as-cast series alloys are composed of the CaCu₅-type and Th₂Zn₁₇-type phases. Saturation magnetization of the samples decreases with the Mo content increasing. Intrinsic coercivities (_iH_c) of no more than 0.06 T are observed in these as-cast samples, due to their rather coarse grain microstructures with an average grain size of 50 μm. The as-milled/annealed SmCo_7−xMo_x powders crystallize in the disordered TbCu₇-type (1:7) structure with very fine nanograins, and a minor Co₃Mo phase appears in the samples with x=0.1-0.4. High _iH_c (?0.95 T) are achieved in these samples, with a maximum of 1.26 T located at x=0.2, which can be primarily attributed to strong pinning of the domain wall motion at the nanograin boundaries. The temperature coefficient (β) of the _iH_c is about −0.22%/°C in the temperature range of 25-400 °C for the as-milled/annealed samples.     

Magnetic properties of half-metallic semi Heusler Co1−xCuxMnSb compounds

A study of the half-metallic character of the semi Heusler alloys Co_1−xCu_xMnSb (0?x?0.9) is presented. We investigated the saturation magnetization M_S at temperatures from 5 K to room temperature and the temperature dependence of the DC magnetic susceptibility χ above Curie temperature T_C. The magnetic moments at 5 K, for most compositions are very close to the quantized value of 4 μ_B for Mn³⁺ ion, the compound with 90% Co substituted by Cu is still ferromagnetic with M_S (5 K)=3.78 μ_B/f.u. These results emphasize the role of Co atoms in maintaining the ferromagnetic order in the material. The Curie temperature is decreased from 476 K to about 300 K as the Cu content increases from 0% to 90%. Above T_C, the χ⁻¹ vs T curves follow very well the Curie–Weiss law. The effective moment μ_eff and paramagnetic Curie temperature θ are derived. A comparison between the values of M_S at 5 K and μ_eff shows a transition from localized to itinerant spin system in these compounds.     

Magnetic behavior of MnAs precipitates in Ga1−xMnxAs diluted magnetic semiconductor

Ferromagnetic Ga_1−xMn_xAs layers (where x≈4.7–5.5%) were grown on (1 0 0) GaAs substrates by molecular beam epitaxy. These p-type (Ga,Mn)As films were revealed to have a ferromagnetic structure and ferromagnetism is observed up to a Curie temperature of 318 K, which is ascribed to the presence of MnAs secondary magnetic phases within the film. It is highly likely that the phase segregation occurs due to the high Mn cell temperature around 890–920 °C, as it is well established that GaMnAs is unstable at such a high temperature. The MnAs precipitate in the samples with x≈4.7–5.5% has a Curie temperature T_c≈318 K, which was characterized from field-cooled and zero-field-cooled magnetization curves.     

Magnetic properties of RNi5−xCux intermetallics

The magnetic properties have been studied for the series of RNi_5−xCu_x intermetallics with R=Y, La, Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, Lu; x  ?2.5. Compositional dependences of magnetic susceptibility for the Pauli paramagnets (R=Y, La, Ce, Lu) and the Curie temperature for ferromagnets (R=Pr, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm) have maximum at x=0.2–0.4$x=0.2–0.4$ and 1, respectively. The substitution of Cu for Ni is accompanied by decreasing spontaneous magnetic moment and increasing coercive force of all ferromagnetic RNi_5−xCu_x but GdNi_5−xCu_x. These results are explained in the frame of band magnetism, random local crystal field, and domain wall pinning theories.     

The magnetic susceptibility of hydrogen-doped partially crystalline (Zr76Ni24)1−xHx metallic glasses

The magnetizations of Zr₇₆Ni₂₄ metallic glass and hydrogen-doped partially crystalline (Zr₇₆Ni₂₄)_1−xH_x metallic glasses have been measured in the temperature range 10-300 K and magnetic fields up to 2 T for various dopant concentrations (x=0, 0.024, 0.043, 0.054). It is found that the samples are paramagnetic and magnetic susceptibility at room temperature, χ(300 K), shows a nonmonotonic behaviour upon hydrogenation. The values of χ(300 K) of the hydrogen-doped partially crystalline (Zr₇₆Ni₂₄)_1−xH_x metallic glasses are reduced with increase in hydrogen content up to x=0.043, whereas for x=0.054, an enhancement of χ(300 K) has been revealed. The magnetic susceptibility is weakly temperature dependent down to 110 K, below which an increase is observed. A shallow minimum exists between 90 and 120 K. The form and magnitude of the observed temperature dependence of the magnetic susceptibility are well accounted for by the sum of the quantum corrections to the magnetic susceptibility. Hydrogen reduces the electronic diffusion constant and influences strongly the quantum interference at defects, slowing down the spin diffusion and enhancing the magnetic susceptibility in the temperature range from 110 down to 10 K.     

Magnetoresistive properties of Zn1−xCoxFe2O4 ferrites

The magnetic and magnetoresistive properties of spinel-type Zn_1−xCo_xFe₂O₄ (x=0, 0.2 and 0.4) ferrites are extensively investigated in this study. A large negative magnetoresistance (MR) effect is observed in Zn_1−xCo_xFe₂O₄ ferrites of spinel structure. These materials are either ferrimagnetic or paramagnetic at room temperature, and show a spin-(cluster) glass transition at low temperatures, depending on the chemical compositions. The MR curves as a function of magnetic fields, MR(H), are parabolic at all temperatures for paramagnetic polycrystalline ZnFe₂O₄. The MR for ZnFe₂O₄ at 110 K in the presence of 9 T applied magnetic field is 30%. On the other hand, MR(H) are linear for x=0.2 and 0.4 ferrimagnetic Zn_1−xCo_xFe₂O₄ samples up to 9 T. The MR effect is independent of the sintering temperatures, and can be explained with the help of the spin-dependent scattering and the Yafet–Kittel angle of Zn_1−xCo_xFe₂O₄ mixed ferrites.     

Magnetic properties of nanocrystalline Co1−xZnxFe2O4 prepared by forced hydrolysis method

Nanocrystalline zinc-substituted cobalt ferrite powders, Co_1−xZn_xFe₂O₄ (x=0, 0.2, 0.4), were for the first time prepared by forced hydrolysis method. Magnetic and structural properties in these specimens were investigated. The average crystallite size is about 3.0 nm. When the zinc substitution increases from x=0 to x=0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g and the coercive field decreases from 1.22 to 0.71 T. All samples are superparamagnetic at room temperature and ferrimagnetic at temperatures below the blocking temperature. The high value of the saturation magnetization and the very thin thickness of the disorder surface layer of all samples suggests that this forced hydrolysis method is suitable not only for preparing two metal element systems but also for three or more ones.     

Phase transition and extended X-ray absorption fine structure of melt-spun amorphous Fe100−xYx alloys

The phase diagram and local structure of melt-spun amorphous (a-) Fe_100−xY_x (22?x?62) alloys were investigated using AC and DC magnetic and extended X-ray absorption fine structure (EXAFS) measurements. The a-Fe–Y system shows reentrant spin glass (RSG) behavior for 42?x?58 and spin glass (SG) behavior for 60?x. Two SG transition temperatures, T_g and T_f, were obtained in the RSG state. The T_g, T_f and Curie temperature T_C decrease with increasing x, and the T_C and T_g vanish at x=60. A new magnetic phase diagram for the melt-spun a-Fe_100−xY_x alloys was obtained from magnetic measurements for higher Y concentration. The magnetic states of the a-Fe_100−xY_x alloys change remarkably around x=60 and an EXAFS study revealed that the average atomic distance between nearest-neighboring Fe atoms changes at approximately x=60.     

Thermodynamic and kinetic properties of Ho1−xTixCo2-hydrogen system

The hydrogen absorption behavior of Laves phase Ho_1−xTi_xCo₂ (x=0.1-0.6) alloys has been investigated by pressure-concentration (PC) isotherms and cyclic-, temperature- and pressure-dependent absorption kinetics. The PC isotherms and kinetics of hydrogen absorption have been studied in the pressure range 0.01-1 bar and temperature range 50-200 °C using Sievert's-type apparatus. The drastic changes in the induction period and particle size during the activation process have been discussed based on the kinetics of repeated hydrogenation cycles and scanning electron microscopy (SEM) images of the hydrides at different hydriding cycles, respectively. The experimental results of kinetic curves are interpreted using the Johnson-Mehl-Avrami (JMA) model, and the reaction order and reaction rate have been determined. The α-, (α+β)- and β-phase regions in Ho_1−xTi_xCo₂-H have been identified from the different slope regions of the first-order-type kinetic plots. The dependence of the reaction rate parameter on hydriding pressure and temperature in the (α+β)-phase region has been discussed.     

Dielectric properties of valence compensated Ca1−xBixTi1−xCrxO3 perovskite prepared using the sol-gel process

Ca_1−xBi_xNb_1−xCr_xO₃ (x=0.01-0.5) ceramic powders were synthesized using the sol-gel process. The single-phase solids can be presented at x=0.01 and 0.03. The coexistence of orthorhombic perovskite and the secondary phase of BiCrO₃ was verified, as presented for x=0.05-0.5. Grains with a micro-cube topography were obtained for x=0.3-0.5. The average grain size is about 0.4 and 1.1 μm for x=0.3 and 0.5, respectively. The highest dielectric constant peak was measured at around 55 °C for x=0.5 and at 75 °C for x=0.3. The high dielectric constant was caused by the formation of barrier layers at the interface of the bi-phase mixed ceramics. Space charge polarization contributed to the observed behavior.     

Transport and magnetic properties of disordered LixVyO2 (x=0.8 and y=0.8)

The magnetic and electron transport properties of rhombohedral Li_xV_yO₂ (x=0.8 and y=0.8) are studied. The dc susceptibility of Li_xV_yO₂ can be well fitted to the modified Curie-Weiss law, which verified the paramagnetic ground state. The magnetic hysteresis and ac susceptibility also confirm this paramagnetism. The Li_xV_yO₂ exhibits semiconducting behavior, which is explained by thermal activated process at high temperature and variable-range hopping mechanism at low temperature. Anderson localization plays an important role in both the electron transport behavior and the magnetic behavior due to the site disorder between the Li⁺ ion and V⁴⁺ ion.     

Magnetic anisotropy of Tb1−xGdxMn6Sn6 compounds

Magnetization curves of Tb_1−xGd_xMn₆Sn₆ compounds (0?x?1) have been measured for aligned powder samples in the temperature range 4.2–300 K in pulsed magnetic fields up to 30 T. Temperature and concentration dependences of the magnetocrystalline anisotropy constants K₁ and K₂ and concentration dependence of the temperature of spontaneous spin-reorientation transition have been determined. Using these data, we estimated the contribution of the manganese and terbium atoms to the magnetic anisotropy of Tb_1−xGd_xMn₆Sn₆ and analyzed the origin of the appearance of field-induced first-order magnetic phase transition in these compounds.     

Hard magnetic properties of ErCo7−xCux [0.3⩽x⩽1] system

We report the observation of excellent hard magnetic properties on purely single phase ErCo_7−xCu_x compounds with x=0.3, 0.5, 0.8 and 1. Cu substitution leads to a decrease in the saturation magnetization, but enhances the uniaxial anisotropy in this system. The large anisotropy field (∼100 kOe) is attributed to the Er and the Co sublattices. Domain wall pinning effect seems to play a crucial role in determining the temperature and field dependences of magnetization in these compounds. The hard magnetic properties obtained at room temperature (RT) are comparable to the best results obtained in other RCo₇ based materials.     

Effect of fabrication parameters on the electrical conductivity of YxSr1−xTiO3 for anode materials

Yttrium-doped strontium titanate (Y_xSr_1−xTiO₃), as probable anode material for SOFC, was prepared by solid-state reaction. The solubility of yttrium in SrTiO₃ at different temperatures was examined and the electrical conductivities of Y_xSr_1−xTiO₃ were measured from 500 to 1000 °C. The effects of doping amount, fabrication atmosphere, and sintering temperature on the electrical conductivity of Y_xSr_1−xTiO₃ were investigated. Y_xSr_1−xTiO₃ with x=0.08 was found to give the maximum electrical conductivity, 71 S/cm at 800 °C in pure hydrogen. Reducing atmospheres and appropriate sintering temperatures play a positive role in improving the electrical conductivity.     

Magnetic properties of the Pr1−xGdxCo4B compounds

In this work, we have investigated the effect of the substitution of Gd for Pr on the crystal structure and magnetic properties of the Pr_1−xGd_xCo₄B compounds for 0?x?1 using X-ray powder diffraction, magnetic measurements, and differential scanning calorimetry (DSC). These compounds have hexagonal CeCo₄B-type structure with the space group P6/mmm. The substitution of Gd for Pr leads to a decrease of the unit-cell parameters a and the unit-cell volume V, while the unit-cell parameter c increases slightly. Magnetic measurements indicate that all samples are ordered magnetically below room temperature. The Curie temperatures determined by DSC technique increase as Pr is substituted by Gd. The saturation magnetization at 5 K decreases upon Gd substitution up to x=0.6, and then increases again.