The transparence comparison of Ga- and Al-doped ZnO thin films

The Ga-doped ZnO (GZO) and Al-doped ZnO (AZO) thin films were grown on quartz glass substrates by pulsed laser deposition under different oxygen partial pressures (PO₂). The transparent performances of films versus properties of structure and conductivity were discussed. With the increase of PO₂, the transmittance of both GZO films and AZO films increased to maximum and then decreased which were in according with the change of crystallization quality. The transmittance of GZO films was higher than that of AZO films, which were not dominated by the impurity ions induced by doping. AFM images and surface roughness mean square coefficients showed that the surfaces of GZO films were smoother than that of AZO films, which were due to the dopant Ga acting as the surfactant and smoothed the GZO films surface.     

Electrical and optical properties of Ga doped zinc oxide thin films deposited at room temperature by continuous composition spread

Ga doped ZnO (GZO) thin films were deposited on glass substrates at room temperature by continuous composition spread (CCS) method. CCS is thin films growth method of various Ga_xZn_1−xO(GZO) thin film compositions on a substrate, and evaluating critical properties as a function position, which is directly related to material composition. Various compositions of Ga doped ZnO deposited at room temperature were explored to find excellent electrical and optical properties. Optimized GZO thin films with a low resistivity of 1.46 × 10⁻³ Ω cm and an average transmittance above 90% in the 550 nm wavelength region were able to be formed at an Ar pressure of 2.66 Pa and a room temperature. Also, optimized composition of the GZO thin film which had the lowest resistivity and high transmittance was found at 0.8 wt.% Ga₂O₃ doped in ZnO.     

Microstructure and optical properties of nanocrystalline ZnO and ZnO:(Li or Al) thin films

Zinc oxide thin films (ZnO, ZnO:Li, ZnO:Al) were deposited on glass substrates by a sol-gel technique. Zinc acetate, lithium acetate, and aluminum chloride were used as metal ion sources in the precursor solutions. XRD analysis revealed that Li doped and undoped ZnO films formed single phase zincite structure in contrast to Al:ZnO films which did not fully crystallize at the annealing temperature of 550 °C. Crystallized films had a grain size under 50 nm and showed c-axis grain orientation. All films had a very smooth surface with RMS surface roughness values between 0.23 and 0.35 nm. Surface roughness and optical band tail values increased by Al doping. Compared to undoped ZnO films, Li doping slightly increased the optical band gap of the films.     

Effect of dopants on the structural,optical and electrical properties of sol–gel derived ZnO semiconductor thin films

Undoped, Ga-, In-, Zr-, and Sn-doped ZnO transparent semiconductor thin films were deposited on alkali-free glasses by sol–gel method. 2-methoxyethanol (2-ME) and diethanolamine (DEA) were chosen as a solvent and a stabilizer, respectively. The doping concentration was maintained at 2 at.% in the impurity doping precursor solutions. The effects of different dopants on the structural, optical, and electrical properties of ZnO thin films were investigated. XRD results show that all annealed ZnO-based thin films had a hexagonal (wurtzite) structure. ZnO thin films doped with impurity elements obviously improved the surface flatness and enhanced the optical transmittance. All impurity doped ZnO thin films showed high transparency in the visible range (>91%). The Ga- and In- doped ZnO thin films exhibited higher Hall mobility and lower resistivity than did the undoped ZnO thin film.     

Preparation of Ga-doped ZnO films by pulsed dc magnetron sputtering with cylindrical rotating target for thin film solar cell applications

Applicability of Ga-doped ZnO (GZO) films for thin film solar cells (TFSCs) was investigated by preparing GZO films via pulsed dc magnetron sputtering (PDMS) with rotating target. The GZO films showed improved crystallinity and increasing degree of Ga doping with increasing thickness to a limit of 1000 nm. The films also fulfilled requirements for the transparent electrodes of TFSCs in terms of electrical and optical properties. Moreover, the films exhibited good texturing potential based on etching studies with diluted HCl, which yielded an improved light trapping capability without significant degradation in electrical propreties. It is therefore suggested that the surface-textured GZO films prepared via PDMS and etching are promising candidates for indium-free transparent electrodes for TFSCs.     

The crystalline structure,conductivity and optical properties of Co-doped ZnO thin films

Transparent conductive Co-doped ZnO thin films were deposited by ultrasonic spray technique. Conditions of preparation have been optimized to get good quality. A set of cobalt (Co)-doped ZnO (between 0 and 3 wt%) thin films were grown on glass substrate at 350 °C. The thin films were annealed at 500 °C for improvement of the physical properties. Nanocrystalline films with hexagonal wurtzite structure and a strong (0 0 2) preferred orientation were obtained. The maximum value of grain size G = 63.99 nm is attained with undoped ZnO film. The optical transmissions spectra showed that both the undoped and doped ZnO films have transparency within the visible wavelength region. The band gap energy decreased after doping from 3.367 to 3.319 eV when Co concentration increased from 0 to 2 wt% with slight increase of electrical conductivity of the films from 7.71 to 8.33 (Ω cm)⁻¹. The best estimated structure, optical and electrical results are achieved in Co-doped ZnO film with 2 wt%.     

Substitution mechanism of Ga for Zn site depending on deposition temperature for transparent conducting oxides

High quality transparent conductive gallium-doped zinc oxide (GZO) thin films were deposited on glass substrates using rf-magnetron sputtering system at the temperature ranging from room temperature (RT) to 500 °C. The temperature-dependence of Ga doping effect on the structural, optical and electrical properties in ZnO has been investigated. For the GZO thin films deposited at over 200 °C, (103) orientation was strongly observed by X-ray diffraction analysis, which is attributed to the substitution of Ga elements into Zn site. X-ray photoelectron spectroscopy measurements have confirmed that oxygen vacancies were generated at the temperature higher than 300 °C. This might be due to the effective substitution of Ga³⁺ for Zn site at higher temperature. It was also found that the optical band gap increases with deposition temperature. The optical transmittance of GZO thin films was above 87% in the visible region. The GZO thin films grown at 500 °C showed a low electrical resistivity of 4.50 × 10^?4 Ω cm, a carrier concentration of 6.38 × 10²⁰ cm^?3 and a carrier mobility of 21.69 cm²/V.     

生长温度对Ga掺杂ZnO薄膜光电性能的影响

在不同衬底温度(室温~750 ℃)条件下,采用脉冲激光沉积(PLD)方法在石英玻璃和单晶硅(111)衬底上制备了Ga掺杂ZnO(GZO)薄膜。结果显示:衬底温度的变化导致衬底表面吸附原子扩散速率和脱附速率的不同,从而导致合成薄膜结晶质量的差异,衬底温度450 ℃时制备的GZO薄膜具有最好的结晶特性;GZO薄膜中载流子浓度随衬底温度升高而单调减小的现象与GZO薄膜中的本征缺陷密切相关,晶界散射强度的变化导致迁移率出现先增大后减小的趋势,衬底温度450 ℃时制备的GZO薄膜具有最小的电阻率~0.02 Ω·cm;随着衬底温度的升高,薄膜载流子浓度的单调减小导致了薄膜光学带隙变窄,所有合成样品的平均可见光透过率均达到85%以上。采用PLD方法制备GZO薄膜,衬底温度的改变可以对薄膜的光电性能起到调制作用。     

Effect of crystallinity of ZnO buffer layer on the properties of epitaxial (ZnO:Al)/(ZnO:Ga) bi-layer films deposited on c-sapphire substrate

Bi-layer ZnO films with 2 wt.% Al (AZO; ZnO:Al) and 4 wt.% Ga-doped (GZO; ZnO:Ga) were deposited on the ZnO buffered and annealed ZnO buffered c(0 0 0 1)-sapphire(Al₂O₃) substrates respectively by Pulsed Laser Deposition (PLD). The effect of crystallinity of ZnO buffer layer on the crystallinity and electrical properties of the AZO/GZO bi-layer thin films was investigated. It was seen that the crystallinity of ZnO buffer layer had a great influence on the orientation and defect density of AZO/GZO bi-layer thin films from X-ray Diffraction (XRD) peaks and High Resolution Transmission Electron Microscopy (HRTEM) images. In a word, it was found in the films that more preferred c-axis orientation texture and reduction of the defects such as stacking faults and dislocations, with increasing of the crystallinity of ZnO buffer layer.     

Blue luminescence from Ce-doped ZnO thin films prepared by magnetron sputtering

The photoluminescence properties of undoped and Ce-doped ZnO thin films that were prepared by DC magnetron sputtering were investigated. It was found that the incorporation of Ce could intensively affect the structural, optical, and photoluminescence properties of the ZnO thin films. The undoped ZnO thin films showed a sharp UV luminescence, whereas the Ce-doped ZnO thin films showed a broad blue luminescence. The effects of excitation wavelength and annealing atmosphere on the photoluminescence properties of Ce-doped ZnO thin films were also studied. After post-annealing in air and oxygen atmospheres, the blue emissions of the prepared films were drastically suppressed. Our results indicate that the blue emissions of Ce-doped ZnO thin films are related to zinc interstitials and the intrinsic transition of Ce³⁺ ions.     

Investigation of structural and optical properties of ZnO films co-doped with fluorine and indium

Undoped ZnO film and ZnO films, which are co-doped with F and In (FIZO) at different concentrations, were synthesized by sol–gel technique and the effects of co-doping of F and In on structural and optical properties of ZnO thin films were investigated. The concentration ratio of [F]/[Zn] was altered from 0.25 to 1.75 with 0.50 step at.% mole and [In]/[Zn] was altered from 0.25 to 1.00 with 0.25 step at.% mole. X-ray diffraction analysis indicates that the films have polycrystalline nature and the (0 0 2) preferred orientation is the stronger peak. No extra phases involving zinc, fluorine and indium compounds were observed even at high F and In content. The grain size of undoped ZnO and FIZO thin films varied between 15 and 20 nm with a small fluctuation. From the SEM images, although the undoped ZnO had a smooth and particle-shaped surface, FIZO films had nanofiber-networks shapes over the surface with average size of 500 nm. The surface morphologies and crystallite sizes for the F and In doped films were slightly different from than those of undoped film. From the optical study, a slight shrinkage of band gap was backwardly observed from 3.36 to 3.25 eV with the increasing of F and In content.     

RF溅射钕掺杂ZnO薄膜的结构与发光特性

通过射频磁控溅射技术在Si(111)衬底上制备了未掺杂ZnO薄膜和Nd掺杂ZnO薄膜。应用XRD分析了ZnO:Nd薄膜的晶格结构,通过AFM观察了ZnO:Nd薄膜的表面形貌。结果表明,Nd掺入了ZnO晶格中,由于Nd原子半径大于Zn原子半径,Nd以替位原子的形式存在于ZnO晶格中。ZnO:Nd薄膜为纳米多晶薄膜,表面形貌粗糙。ZnO:Nd薄膜的室温光致发光谱表明,相同条件下制备的未掺杂ZnO薄膜和Nd掺杂ZnO薄膜都出现了395nm的强紫光带和495nm的弱绿光带。我们认为,紫光发射峰窄而锐且强度远大于绿光峰,源于薄膜中激子复合;绿光峰强度较弱,源于薄膜中的氧空位(VO)及氧反位锌缺陷(OZn)。Nd掺杂没有影响ZnO:Nd薄膜的PL谱的发射峰的峰位。由于Nd3 离子电荷数与Zn2 离子电荷数不相等,为了保持ZnO薄膜的电中性,间隙锌(VZn)可以作为Nd替位补偿性的受主杂质而存在,影响ZnO薄膜的激子浓度。同时,Nd掺入使ZnO的晶格畸变缺陷浓度改变增强,因而发射峰的强度随Nd掺杂浓度不同而变化。     

Influence of strain/stress on the nonlinear-optical properties of sprayed deposited ZnO:Al thin films

Nanocrystalline ZnO:Al thin films were deposited by reactive chemical pulverization spray pyrolysis technique on heated glass substrates at 450 °C to study their crystalline structure, composition, strain, stress, roughness characteristics and nonlinear optical susceptibility as a function of Al concentration (0, 2, 3, 5 at.%). The films were characterized by X-ray diffractometer (XRD), EDAX 9100 analyser, atomic force microscopy (AFM) and third harmonic generation (THG). The Al (3 at.%) doped ZnO thin films exhibited the lower strain/stress than undoped films. The nonlinear properties of the ZnO:Al thin films have been found to be influenced by the films strain/stress.     

Effect of graphene/ZnO hybrid transparent electrode on characteristics of GaN light-emitting diodes

In order to reduce the Schottky barrier height and sheet resistance between graphene(Gr) and the p-GaN layers in GaN-based light-emitting diodes(LEDs), conductive transparent thin films with large work function are required to be inserted between Gr and p-GaN layers. In the present work, three kinds of transparent conductive oxide(TCO) zinc oxide(ZnO) films, Al-, Ga-, and In-doped ZnO(AZO, GZO, and IZO), are introduced as a bridge layer between Gr and p-GaN,respectively. The influence of different combinations of Gr/ZnO hybrid transparent conducting layers(TCLs) on the optical and thermal characteristics of the GaN-LED was investigated by the finite element method through COMSOL software. It is found that both the TCL transmittance and the surface temperature of the LED chip reduce with the increase in Gr and ZnO thickness. In order to get the transmittance of the Gr/ZnO hybrid TCL higher than 80%, the appropriate combination of Gr/ZnO compound electrode should be a single layer of Gr with ZnO no thicker than 400 nm(1 L Gr/400-nm ZnO),2 L Gr/300-nm ZnO, 3 L Gr/200-nm ZnO, or 4 L Gr/100-nm ZnO. The LEDs with hybrid TCLs consisting of 1 L Gr/300-nm AZO, 2 L Gr/300-nm GZO, and 2 L Gr/300-nm IZO have good performance, among which the one with 1 L Gr/300-nm GZO has the best thermal property. Typically, the temperature of LEDs with 1 L Gr/300-nm GZO hybrid TCLs will drop by about 7 K compared with that of the LEDs with a TCL without ZnO film.     

ZnO：V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO:V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO:V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO:V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

Influence of polarity inversion on the electrical properties of Ga‐doped ZnO thin films

This study investigates how polarity inversion influences the relationship between the electrical properties of heavily Ga‐doped ZnO (GZO) films deposited by RF magnetron sputtering and their thickness. The electrical properties observed in very thin films are correlated with a change of polarity from O‐polar to Zn‐polar face upon increasing the film thickness based on results of valence band spectra measured by X‐ray photoelectron spectroscopy. It is found that the electrical properties of very thin GZO films deposited on Zn‐polar ZnO templates are significantly improved compared to those deposited on O‐polar face. A low resistivity of 2.62 × 10^–4 Ω cm, high Hall mobility of 26.9 cm²/V s, and high carrier concentration of 8.87 × 10²⁰ cm^–3 being achieved with 30 nm‐thick GZO films using Zn‐polar ZnO templates on a glass substrate. In contrast, the resistivity of 30 nm‐thick GZO films on bare glass that shows more likely O‐polar is very poor about 1.44 × 10^–3 Ω cm with mobility and carrier concentration are only 11.9 cm²/V s and 3.64 × 10²⁰ cm^–3, respectively. It is therefore proposed that polarity inversion plays an important role in determining the electrical properties of extremely thin GZO films. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Nanostructure and optical properties of M doped ZnO (M=Ni, Mn) thin films prepared by sol-gel process

The transparent thin films of undoped, Mn-doped, and Ni-doped zinc oxide (ZnO) have been deposited on glass substrates via sol-gel technique using zinc acetate dehydrate, nickel chloride, and manganese chloride as precursors. The structural properties and morphologies of the deposited undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/vis spectroscopy. The analyzed results indicate that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn or Ni related phases. The band gap energy was estimated by Tauc's method and found to be 3.28, 3.26, and 3.34 eV for ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films at room temperature, respectively. Room temperature photoluminescence is observed for the ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films.     

A comparative study on structural and optical properties of ZnO and Al-doped ZnO thin films obtained by ultrasonic spray method using different solvents

Transparent conducting ZnO and Al doped ZnO thin films were deposited on glass substrate by ultrasonic spray method. The thin films with concentration of 0.1 M were deposited at 350 °C with 2 min of deposition time. The effects of ethanol and methanol solution before and after doping on the structural, optical and electrical properties were examined. The DRX analyses indicated that ZnO films have nanocrystalline nature and hexagonal wurtzite structure with (1 0 0) and (0 0 2) preferential orientation corresponding to ZnO films resulting from methanol and ethanol solution, respectively. The crystallinity of the thin films improved with methanol solution after doping to (0 0 2) oriented. All films exhibit an average optical transparency about 90%, in the visible range. The band gaps values of ZnO thin films are increased after doping from 3.10 to 3.26 eV and 3.27 to 3.30 eV upon Al doping obtained by ethanol and methanol solution, respectively. The electrical conductivity increase from 7.5 to 15.2 (Ω cm)⁻¹ of undoped to Al doped ZnO thin films prepared by using ethanol solution. However, for the methanol solution; the electrical conductivity of the film is stabilized after doping.     

Influence of glucose on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method on glass substrates followed by calcinations at 500 °C for an hour. The effect of glucose on the structure and optical properties of the films was studied. The structural characteristics of the samples were analyzed by X-ray diffractometer (XRD) and atomic force microscope (AFM). The optical properties were studied by a UV-visible spectrophotometer. The results show that some of the prepared ZnO thin films have a high preferential oriented c-axis orientation with compact hexagonal wurtzite structure due to a proper amount of glucose introducing. After introducing the glucose additive in ZnO colloids, the intensity of (002) peak, the transmittance, and the optical band gap of the ZnO thin films increases because of the enhanced ZnO crystallization. On the contrary, the absorbance, the film thickness, and the surface root-mean-square (RMS) roughness of the ZnO thin films decreases. The glucose additive could not only improve the surface RMS roughness and microstructure of ZnO thin films, but also enhance the transmittance and the energy band gap more easily.