Fabrication of textured SnO2:F thin films by spray pyrolysis

Transparent conductive SnO₂:F thin films with textured surfaces were fabricated on soda-lime-silica glass substrates by spray pyrolysis. Structure, morphology, optical and electrical properties of the films were investigated. Results show that the film structure, morphology, haze, transmittance and sheet resistance are dependent on the substrate temperature and film thickness. An optimal 810 nm-thick SnO₂:F film with textured surface deposited at 520 °C exhibits polycrystalline rutile tetragonal structure with a (2 0 0) orientation. The sheet resistance, average transmittance in visible region, and haze of this film were 8 Ω/□, 80.04% and 11.07%, respectively, which are suitable for the electrode used in the hydrogenated amorphous silicon solar cells.     

Gas sensing properties of nanostructured MoO3 thin films prepared by spray pyrolysis

Thin films of molybdenum trioxide (MoO₃) were deposited on common glass using the chemical spray pyrolysis technique. A (NH₄)₆Mo₇O₂₄4H₂0 solution 0.1 M was used as the precursor one. The influence of substrate temperature on the crystallographic structure, surface morphology and electrical behavior of MoO₃ thin films was studied. MoO₃ can exist in two crystalline forms, the thermodynamically stable orthorhombic α-MoO₃ and the metastable monoclinic β-MoO₃ phase. XRD-spectra showed a growth of α-MoO₃ phase percentage as substrate temperature increases from 420 K up to 670 K. Films deposited in the 500–600 K range have a clearly porous surface structure of nanometer order as can be seen in SEM images. Changes up to six magnitude orders were observed in MoO₃ thin films electrical resistance when films temperature varied from 100 K up to 500 K. The sensing property of these MoO₃ films was also studied. The sensitivity was investigated in the temperature range 160 and 360 K for H₂O and CO gases, respectively. Both of them are of reducing nature. In all studied cases sensitivity decreases slowly as film temperature is raised. At room temperature the sensitivity changes from 12 up to 75% depending on substrate temperature. The sensitivity for CO gas was found to be lower than that of H₂O.     

Growth of ultra-thin TiO2 films by spray pyrolysis on different substrates

In the present study TiO₂ films were deposited by spray pyrolysis method onto ITO covered glass and Si (1 0 0) substrates. The spray solution containing titanium(IV) isopropoxide, acetylacetone and ethanol was sprayed at a substrate temperature of 450 °C employing 1-125 spray pulses (1 s spray and 30 s pause). According to AFM, continuous coverage of ITO and Si substrates with TiO₂ layer is formed by 5-10 and below 5 spray pulses, respectively. XPS studies revealed that TiO₂ film growth on Si substrate using up to 4 spray pulses follows 2D or layer-by-layer-growth. Above 4 spray pulses, 3D or island growth becomes dominant irrespective of the substrate. Only 50 spray pulses result in TiO₂ layer with the thickness more than XPS measurement escape depth as any signal from the substrate could not be detected. TiO₂ grain size remains 30 nm on ITO and increases from 10-20 nm to 50-100 nm on Si substrate with the number of spray pulses from 1 to 125.     

Physico-chemical, optical and electrochemical properties of iron oxide thin films prepared by spray pyrolysis

Iron oxide thin films were prepared by spray pyrolysis technique onto glass substrates from iron chloride solution. They were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and (UV-vis) spectroscopy. The films deposited at T_s ≤ 450 °C were amorphous; while those produced at T_sub = 500 °C were polycrystalline α-Fe₂O₃ with a preferential orientation along the (1 0 4) direction. By observing scanning electron microscopy (SEM), it was seen that iron oxide films were relatively homogeneous uniform and had a good adherence to the glass substrates. The grain size was found (by RX) between 19 and 25 nm. The composition of these films was examined by X-ray photoelectron spectroscopy and electron probe microanalysis (EPMA). These films exhibited also a transmittance value about 80% in the visible and infrared range. The cyclic voltammetry study showed that the films of Fe₂O₃ deposited on ITO pre-coated glass substrates were capable of charge insertion/extraction when immersed in an electrolyte of propylene carbonate (PC) with 0.5 M LiCLO₄.     

Mg和Zn掺杂CuAlS2电子结构的分析

从能带结构和态密度分析了黄铜矿CuAlS₂的电子结构.对比未掺杂CuAlS₂,从晶体结构、电子结构、电荷密度分布讨论了Mg和Zn替位Al掺杂对CuAlS₂的影响.结果表明:Mg和Zn掺杂CuAlS₂都导致晶格常数增大,Mg掺杂晶胞体积增大更多;掺杂在价带顶引入受主态,形成p型电导;Mg掺杂比Zn掺杂的受主能级电离能略小;而Zn掺杂CuAlS₂体系总能更低,晶格结构更稳定. 关键词： 2')" href="#">CuAlS₂ p型掺杂 电子结构 能带结构     

Structural, electrical and optical properties of TiO2 doped WO3 thin films

TiO₂ doped WO₃ thin films were deposited onto glass substrates and fluorine doped tin oxide (FTO) coated conducting glass substrates, maintained at 500 °C by pyrolytic decomposition of adequate precursor solution. Equimolar ammonium tungstate ((NH₄)₂WO₄) and titanyl acetyl acetonate (TiAcAc) solutions were mixed together at pH 9 in volume proportions and used as a precursor solution for the deposition of TiO₂ doped WO₃ thin films. Doping concentrations were varied between 4 and 38%. The effect of TiO₂ doping concentration on structural, electrical and optical properties of TiO₂ doped WO₃ thin films were studied. Values of room temperature electrical resistivity, thermoelectric power and band gap energy (E_g) were estimated. The films with 38% TiO₂ doping in WO₃ exhibited lowest resistivity, n-type electrical conductivity and improved electrochromic performance among all the samples. The values of thermoelectric power (TEP) were in the range of 23-56 μV/K and the direct band gap energy varied between 2.72 and 2.86 eV.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Cathodoluminescence characteristics of particles and film of (Y, Zn)2O3:Eu phosphor prepared by spray pyrolysis

Eu-doped Y₂O₃ particles with spherical shape and fine size were prepared by spray pyrolysis. The cathodoluminescence of Y₂O₃:Eu³⁺ powder was optimized by substituting small amount of zinc atoms in place of yttrium sites. As a result, the optimized (Y, Zn)₂O₃:Eu³⁺ phosphor showed 60% improved cathodoluminescence compared with Y₂O₃:Eu³⁺ particles. The prepared (Y, Zn)₂O₃:Eu³⁺ phosphor had spherical shape and 0.726 μm in mean size. Using these particles, the thickness of the phosphor film was controlled by varying the phosphor loading. The brightness and luminous efficiency of phosphor films prepared were monitored with varying the accelerating voltage ranges from 4 to 14 kV. The dependency of the luminous efficiency on the accelerating voltage was very sensitive to the phosphor loading. As increasing the accelerating voltage from 4 to 14 kV, the brightness of phosphor films prepared was monotonically increased from 200 to 1085 cd/cm²_, but the saturation in the luminous efficiency appeared at 10 kV. The highest efficiency was achieved when the number of phosphor-particles layer was about 3. More details about the luminous efficiency and brightness were discussed with changing the phosphor loading.     

Structural, optical and electrochemical properties of TiO2 thin films grown by APCVD method

Atmospheric pressure chemical vapor deposition (APCVD) of TiO₂ thin films has been achieved onto glass and onto ITO-coated glass substrates, from the reaction of TiCl₄ with ethyl acetate (EtOAc). The effect of the synthesis temperature on the optical, structural and electrochemical properties was studied through spectral transmittance, X-ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS) measurements. It was established that the TiO₂ films deposited onto glass substrate, at temperatures greater than 400 °C grown with rutile type tetragonal structure, whereas the TiO₂ films deposited onto ITO-coated glass substrate grown with anatase type structure. EIS was applied as suitable method to determine the charge transfer resistance in the electrolyte/TiO₂ interface, typically found in dye-sensitized solar cells.     

Electrochromic properties of spray deposited TiO2-doped WO3 thin films

TiO₂-doped WO₃ thin films were deposited onto fluorine-doped tin oxide coated conducting glass substrates using spray pyrolysis technique at 525 °C. The volume percentage of TiO₂ dopant was varied from 13% to 38%. The thin film samples were transparent, uniform and strongly adherent to the substrates. Electrochromical properties of TiO₂-doped WO₃ thin films were studied with the help of cyclic voltammetry (CV), chronoamperometry (CA) and chronocoulometry (CC) techniques. It has been found that TiO₂ doping in WO₃ enhances its electrochromic performance. Colouration efficiency becomes almost double and samples exhibit increasingly high reversibility with TiO₂ doping concentrations, in the studied range.     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

Structural and optical properties of SrCu2O2 films deposited on sapphire substrates by pulsed laser deposition

We deposited SrCu₂O₂ (SCO) films on sapphire (Al₂O₃) (0 0 0 1) substrates by pulsed laser deposition. The crystallographic orientation of the SCO thin film showed clear dependence on the growth temperature. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis showed that the film deposited at 400 °C was mainly oriented in the SCO [2 0 0] direction, whereas when the growth temperature was increased to 600 °C, the SCO film showed a dominant orientation of SCO [1 1 2]. The SCO film deposited at 500 °C was obvious polycrystalline, showing multi peaks from (2 0 0), (1 1 2), and (2 1 1) diffraction in the XRD spectrum. The SCO film deposited at 600 °C showed a band gap energy of 3.3 eV and transparency up to 80% around 500 nm. The photoluminescence (PL) spectra of the SCO films grown at 500 °C and 600 °C mainly showed blue-green emission, which was attributed to the intra-band transition of the isolated Cu⁺ and Cu⁺–Cu⁺ pairs according to the temperature dependent-PL analysis.     

Luminescence of ZnWO4 and CdWO4 thin films prepared by spray pyrolysis

Thin films of ZnWO₄ and CdWO₄ were prepared by spray pyrolysis and the structural, optical, and luminescence properties were investigated. Both ZnWO₄ and CdWO₄ thin films showed a broad blue-green emission band. The broad band of ZnWO₄ films was centered at 495 nm (2.51 eV) consisted of three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 540 nm (2.30 eV). The broad band of CdWO₄ films at 495 nm (2.51 eV) could be decomposed to three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 545 nm (2.28 eV). These results are consistent with emission from the WO₆⁶⁻ molecular complex. The luminance and efficiency for ZnWO₄ film at 5 kV and 57 μA/cm² were 48 cd/m² and 0.22 lm/w, respectively, and for CdWO₄ film the values were 420 cd/m² and 1.9 lm/w.     

Spray pyrolytic deposition of transparent aluminum oxide (Al2O3) films

Optically transparent Al₂O₃ films has been synthesized, on quartz substrates at 500, 600 and 700 °C, from 0.02 M aluminum acetyl acetonate (Al(acac)₃) in ethanol, by using ultrasonic spray pyrolysis technique. The films synthesized at 500, 600 and 700 °C are amorphous having average particle sizes 27 ± 6, 18 ± 3 and 14 ± 3, respectively. The films are found to be 95% optically transparent in the visible region. The optical transparency of the films in the ultraviolet region is found to increase with increase in deposition temperature. The observed increase in optical band gap and decrease in refractive index is attributed to the decrease in particle size with increase in deposition temperature. The stoichiometry and chemical bonding of the amorphous film studied using XPS and FTIR spectroscopy revealed the presence chemisorbed oxygen.     

Electrochemical characterization of Mn: Co3O4 thin films prepared by spray pyrolysis via aqueous route

Present investigation reports, spray pyrolytic deposition of Mn: Co₃O₄ thin films onto the stainless steel by spray pyrolysis, at the deposition temperature 573 ± 2 K via aqueous route. Prepared electrodes were characterized structurally and morphologically by means of XRD and SEM. Also optical and electrochemical characterizations were carried out in depth. Structural characterization confirms face centered cubic and tetragonal body centered crystal structures for Co₃O₄ and Mn₃O₄ respectively. The rough granular morphology is observed form SEM. Electrochemical study reveals the pseudo capacitive as well as double layer behavior with optimum specific capacitance 485.29 F/g at the scan rate 1 mV/s in 1 M KOH electrolyte. Specific energy, specific power and columbic efficiency were calculated using chronopotentiometric technique. Electrochemical impedance spectroscopy was carried out in the frequency range 1 mHz–1 MHz. Randles equivalent circuit parameters associated with the operative cell are reported.     

Electrochemically deposited photoactive CdIn2Se4 thin films: Structural and optical studies

Electrochemical synthesis of photoactive cadmium-indium-selenide (CdIn₂Se₄) thin films at ambient temperature was reported. The nanocrystalline nature and 1:2:4 elemental chemical stoichiometric ratio for Cd, In and Se were obtained from the X-ray diffraction and energy dispersive X-ray analysis, respectively. Irregular shaped islands of about 400-500 nm in sizes composed of large number of small (∼30-40 nm) spherical grains were confirmed from the atomic force microscopy and the scanning electron microscopy images. The photoelectrochemical measurement of CdIn₂Se₄ film electrode in presence of 1 M polysulphide electrolyte revealed 0.42% photoelectrochemical device conversion efficiency, under the light illumination intensity of 80 mW/cm².     

Physical properties of ZnO thin films deposited by spray pyrolysis technique

Thin films of ZnO have been prepared on glass substrates at different thicknesses by spray pyrolysis technique using 0.2 M aqueous solution of zinc acetate. X-ray diffraction reveals that the films are polycrystalline in nature having hexagonal wurtzite type crystal structure. The resistivity at room temperature is of the order 10⁻² Ω cm and decreased as the temperature increased. Films are highly transparent in the visible region. The dependence of the refractive index, n, and extinction coefficient, k, on the wavelength for a sprayed film is also reported. Optical bandgap, E_g, has been reported for the films. A shift from E_g = 3.21 eV to 3.31 eV has been observed for deposited films.     

Enhanced optical properties of Al-doped TiO2 thin films in oxygen or nitrogen atmosphere

Al-doped TiO₂ (TiO₂:Al) films were deposited by simultaneous RF magnetron sputtering of TiO₂ and DC magnetron sputtering of Al. The advantage of this method is that the Al content could be independently controlled. By depositing in a mixed Ar-O₂ or a mixed Ar-N₂ atmosphere, the TiO₂:Al film became more stoichiometric and the nanocrystallinity was enhanced. The nonlinear refractive index of TiO₂:Al film deposited in a pure Ar, a mixed Ar-O₂ or a mixed Ar-N₂ atmosphere was measured by Moiré deflectometry, and was of the order of 10⁻⁸ cm² W⁻¹. For the TiO₂:Al film deposited in a pure Ar atmosphere, the porosity was higher corresponding to the lower transmission. However, the porosity of TiO₂:Al film decreased as the oxygen or nitrogen pressure increased. Especially, as the ratio of O₂ to Ar pressure increased to 0.22, TiO₂:Al film exhibited lower porosity, higher visible transmission, higher linear refractive index, lower stress and lower stress-optical coefficient.     

Te/TeO2-SiO2复合薄膜的吸收和非线性光学特性研究

应用分光光度计测量Te/TeO₂-SiO₂复合薄膜的透射光谱和吸收光谱, 在480nm附近观察到Te颗粒引起的等离子体共振吸收峰; 采用Z扫描技术研究了共振(激发波长为532 nm)和非共振情况下(激发波长1064 nm) 不同电位制备薄膜的Te颗粒状态与复合薄膜的三阶非线性极化率的关系. 基于有效介质理论对复合薄膜的三阶非线性效应进行分析, 研究Te颗粒大小对Te/TeO₂-SiO₂复合薄膜的非线性光学性质的影响及其产生机理. 结果表明薄膜制备过电位增大, Te的粒径减小, 颗粒数量多, 颗粒分布趋于均匀, 使得金属颗粒的表面等离子体共振峰红移, 吸收强度增强, 导致三阶非线性光学效应增强, χ⁽³⁾由1064 nm的5.12×10^-7 esu增大为532 nm的8.11×10^-7 esu. 关键词： 碲 二氧化碲 复合薄膜 三阶非线性