Operation of thin-film gated SOI lateral PIN photodetectors with gate voltage applied and intrinsic length variation

This paper describes the operation principle of thin-film gated SOI lateral PIN photodetectors, and an analytical model of depletion voltage is presented and validated by two-dimensional Atlas simulations. With gate voltage applied to achieve fully depleted (FD) condition in intrinsic region, the variation of intrinsic length (L_i) on photocurrent and dark current characteristics, sensitivity, and speed is addressed. With L_i between 1 and 10 μm, the simulated results predict internal quantum efficiency (QI) in excess of 95% even near 100% at a 400 nm wavelength. Also, QI can yield over 87% for the long channels. Under FD condition, the total −3 dB frequency value can achieve 16 GHz (19 GHz) for L_i = 1  and 4.1 GHz (6.2 GHz) for L_i = 2 μm with V_K = 1.0 V (2.0 V). And a high ratio of more than 10⁷ between illuminated and dark currents can be yielded for all detectors realized in 0.18 μm SOI CMOS technology.     

Design and performance of a compact superconducting duplexer at VHF-band

This paper presents the design, fabrication, and performance of a compact high temperature superconducting duplexer at VHF-band. The duplexer consists of a T-junction and two four-pole filters with an ultra-narrow bandwidth of 400 kHz at 216 MHz and 220 MHz, respectively. By using gap-coupled feedlines in the filter design procedure, the duplexer is constructed by connecting the two filters using a T-junction with short-length branches. The two filters are fabricated on separate substrates and are carefully packaged to achieve a high isolation between the duplexer channels. The duplexer has a compact size of 41.6 mm × 28 mm. The measured results at 73 K show a high performance. The return loss is −17 dB, the insertion losses of both channels are less than 0.16 dB, and the out-of-band rejections are higher than 60 dB. The isolation between the two channels is better than 76 dB.     

Annoyance and self-reported sleep disturbances due to structurally radiated noise from railway tunnels

In Norway, the requirement for structure borne noise from tunnels is L_pAFmax = 32 dB inside dwellings. According to the Norwegian Standard 8175 it is expected that up to 20% of the exposed population are disturbed by the noise at this level. However, the scientific basis for this noise limit is poor. The aim of this study was to determine the degree of annoyance and self-reported sleep disturbances as a function of L_pAFmax. In the present study, 521 dwellings exposed to structural sound from railway rock-tunnels were identified. A questionnaire was sent to one randomly selected person above 18 years of age from each dwelling. The results showed that both noise induced annoyance and reported sleep disturbances were significantly related to L_pAFmax. Other factors that increased the annoyance were high pass-by frequency of freight trains per day, and degree of sound insulation of the windows. At L_pAFmax = 32 dB, 20% were slightly or more than slightly annoyed, and 4% were moderately or more than moderately annoyed. According to the pre-existing assumption that up to 20% of the exposed population are disturbed by the noise at this level, the present results give support to the Norwegian noise limit L_pAFmax = 32 dB inside dwellings of structure borne noise from railway tunnels.     

Crosstalk in double-pumped fiber optic parametric amplifiers for wavelength division multiplexing systems

We study experimentally inter-channel crosstalk in double-pumped fiber optic parametric amplifiers constructed with conventional dispersion shifted fibers (DSFs) having different lengths (L_A = 13.8, L_B = 6.8, L_C = 4.3, and L_D = 0.8 km). For long fibers (L_A and L_B), eye diagram measurements in a 5-channel (100 GHz spacing) system show that in order to have negligible crosstalk, the output signal power per channel, P_s, should be limited to P_s < 0 dBm. By decreasing the fiber length (to L_C) it is possible to increase the output signal power and/or the number of signals while keeping the crosstalk on negligible levels. This trend was further confirmed by using a very short DSF (L_D = 0.8 km).Finally, we experimentally demonstrate that a general trend in 2P-FOPAs is that spurious FWM increases with the number of signal channels up to a given number of channels when a saturation regime is reached. This saturation of the generation of spurious tones occurs when the bandwidth occupied by the signals exceeds ∼4-5 nm.     

Aperture array Fabry-Perot interference filter

We demonstrate effective implementation of the Fabry-Perot interferometer with subwavelength aperture arrays on its two metal mirrors to achieve polarization-independent narrow band-pass filtering. By superimposing of aperture array fundamental resonance transmission with one of the Fabry-Perot interference peaks, the moderate filter insertion loss of −5 dB, narrow band-pass width of 15 μm, and efficient out-of-band rejection within the ∼0.1-3 THz range are reported. The Siemens-star-shaped apertures in arrays play an important role to achieve such polarization independence and small insertion loss.     

Birefringence of CuGa2S4 crystals

The interference of optical transmission spectra of thin CuGaS₂ single crystals is measured in E||c and E⊥c polarizations. The spectral dependencies of the refractive indexes n_o, n_e and Δn = n_o − n_e near the absorption edge have been determined from interference spectra. The intersection of refractive indexes at two wavelengths has been revealed at 300 K and 10 K. The characteristics of Band-Pass-Mode Filter and Band-Elimination-Mode Filter have been measured, which possess 7 narrow absorption (transmission) bands and represent a comb filter. The characteristics of these filters have been studied.     

An ultra-narrow band eight-pole dual-mode HTS patch filter

An ultra-narrow band eight-pole dual-mode HTS patch filter was designed and fabricated. The filter is constructed by four corner-cut square patches, each of which has two resonating modes. The influence of the change of the corner-cut position on the filter response was investigated by simulations. Four small rectangle patches were added in the topology of the filter as tuning tools. By employing this unique tuning structure, the simulated filter responses and current density distributions on the patches have been greatly improved. The filter was fabricated using double sided YBCO films on a 3 in. LaAlO₃ substrate. The measured results showed satisfactory performance with center frequency 2.494 GHz, fractional bandwidth 0.2%, return loss in passband better than 16 dB, and out-of-band rejection of the filter better than 90 dB at 15 MHz away from its center frequency.     

Preparation and properties of cobalt oxides coated carbon fibers as microwave-absorbing materials

Cobalt oxides/carbon fibers (CoO_x/CFs) composites were synthesized by thermal oxidation of cobalt coated carbon fibers (Co/CFs). The scanning electron microscopy images and X-ray diffraction pattern indicate that the layers are about 0.7 μm and composed of Co₃O₄ and CoO (CoO_x), the preferred condition for preparation of CoO_x/CFs composites is to anneal Co/CFs precursors at 350 °C for 3 h in air. The coercivity, saturation magnetization and residual magnetization of the CoO_x/CFs composites are 464.8 Oe, 10.62 emu/g and 2.21 emu/g, respectively. The reflectivity of cobalt oxides coated carbon fibers (1.11-5.12 mm in thickness) is less than −10 dB over the working frequency range of 4.04-18.00 GHz and less than −20 dB over 11.54-14.77 GHz. The lowest reflectivity is −45.16 dB at 13.41 GHz when the thickness is 1.50 mm.     

Terahertz wave narrow bandpass filter based on photonic crystal

We designed a narrow bandpass terahertz wave filter using photonic crystals with a line defect. An inserted linear defect in one-dimensional photonic crystal structures for a channeled filtering in the terahertz range are studied and designed theoretically. By using transfer matrix method, we examined the transmittance spectra for the proposed terahertz wave filter has a 3 dB transmission loss bandwidth of 20 MHz ranging from 0.29998 THz to 0.30001 THz. The simulated results show that a very narrow transmission band and high transmission (higher than 99.99%) centered at λ₀, and very sharp edges can be achieved.     

Influence of turbulence on train noise

The subject of this paper is the long distance propagation of train noise. The sound exposure level of train noise L_AE was measured. To describe the results of measurements, a semi-analytical model was used. It takes into account the wave-front divergence, air absorption, ground effect, and the turbulence destroying the coherent nature of the ground effect. The model contains three adjustable parameters that must be estimated at the site. To verify the model, we performed measurements of L_AE at the distance D = 450 m from the train track center. The difference between the calculated and measured mean values of L_AE equals 1.3 dB.     

Analyses of transmission characteristics of Rb, Rb and Rb Faraday optical filters at 532 nm

In this paper, the transmission characteristics for Rb, ⁸⁵Rb and ⁸⁷Rb Faraday optical filters at 532 nm that can be used to detect the practical and important frequency-doubled Nd:YAG laser are analyzed and discussed. The theoretical model of an excited-state Faraday optical filter based on the hyperfine structures of atomic system in the intermediate field, what is to our knowledge, is firstly reported. This model predicts that the peak transmission is approximately 50% with an equivalent bandwidth of less than 3 GHz for filters operating on the 5P_1/2 → 10S_1/2 transition in Rb, ⁸⁵Rb and ⁸⁷Rb vapors, respectively. Moreover, the transmission property of ⁸⁷Rb atomic vapor is superior to that of Rb, ⁸⁵Rb atomic vapors, which makes it more suitable for the operation material of Faraday optical filters by comparison with natural Rb vapor.     

Optimization of long-period grating inscribed in large mode area photonic crystal fiber for design of bandstop filter

By inscribing long period grating (LPG) in a photonic crystal fiber (PCF), optical filters for communication wavelengths can be fabricated. In this paper, by utilizing coupled-mode theory and enhanced improved vectorial effective index method, a design of bandstop filter based on optimal LPG parameters is presented where the optimized full-width half-maximum (FWHM), the number (N) and total length of gratings of LPGs (L) are determined. As a result, by the determination of optimized LPG parameters with an optimum length of L_opt=6.5 mm and optimum number of grating N_opt=27 inscribed in the PCF, a bandstop optical filter with FWHM=1 nm is designed.     

Microwave absorption properties of rod-shaped Co-Ni-P shells prepared by metallizing Bacillus

The rod-shaped Co-Ni-P shells were prepared by metalling Bacillus. The microstructures and composition of the shells were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive analysis (EDS). The electromagnetic parameters were measured by the coaxial line method in the frequency of 2-18 GHz. It was found that the Bacillus were successfully coated with Co-Ni-P, and the inner structure of the shells are hollow in structure. The shells exhibit excellent microwave absorption properties in 5-17 GHz frequency. The microwave reflection loss is above −10 dB in 5.38-16.6 GHz frequency. The maximum microwave reflection loss reaches −35.83 dB at 9.12 GHz for samples thickness 2.4 mm, and the widest bandwidth for microwave reflection loss above −10 dB is about ∼5.32 GHz for samples thickness 2.0 mm. These results confirm the feasibility of applying Bacillus as biotemplates for fabrication of the metallic shells as lightweight microwave absorption materials are very promising for applications.     

Performance analysis of WDM-PON architecture using different receiver filters

In this paper the performance effect of a 40 Gb/s Wavelength-Division-Multiplexed Passive Optical Network (WDM-PON) is analyzed using different receiver filters namely Integrator filter, Bessel filter, Butterworth filter, Chebyshev filter, Inverse Chebyshev filter, Elliptic filter, Gaussian filter and Rectangular filter. The data rate and channel spacing are taken as 10 Gb/s per channel and 100 GHz, respectively. Among all the investigated filters, Bessel filter is considered to be the best one for WDM-PON network by the obtained BER and Q factor values.     

Magnetic and electromagnetic properties of composites of iron oxide and Co-B alloy prepared by chemical reduction

Magnetic and electromagnetic properties were investigated on the composites of iron oxide and Co-B alloy, which were prepared by a modified chemical reduction method. The composites are characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDXA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and vibrating sample magnetometry (VSM). The complex electromagnetic parameters (permittivity ε_r=ε_r′+jε_r″ and permeability μ_r=μ_r′+jμ_r″) of paraffin mixed composite samples (paraffin:composites=1:1 in mass ratio) were measured in the frequency range 2-18 GHz by vector network analyzer. The measured real part (ε_r′) and imaginary part (ε_r″) of the relative permittivity show two resonant peaks in the range of 2-18 GHz. The imaginary parts of relative permeability (μ_r″) of all samples exhibited one broad resonant peak over the 2-8 GHz range. The μ_r″ of samples with higher molar ratio of Co to Fe (C and D) shows negative values within 13-18 GHz, which exhibit resonant and antiresonant permeabilities simultaneously. Calculation results indicated that the reflection loss values of the composites and paraffin wax mixtures are less than −10 dB with frequency width of about 6 GHz at the matching thickness.     

DWDM VSB modulation-format optical transmission: Effects of optical filtering and electrical equalization

The transmission of 40 Gb/s wavelength multiplexed channels under vestigial single side band modulation format is transmitted over long haul optically amplified fiber systems. Bit-error-rate (BER) of 10⁻¹² or better can be achieved across all channels. Optical filters are designed with asymmetric roll-off bands. Simulations of the transmission performance, BER versus receiver sensitivity are demonstrated with wavelength channel spacing of 20–40 GHz. An optical filter, whose passband is 28 GHz and 20 dB cut-off band, performs best for 40 Gb/s bit rate due to optimum filtering and minimum noise contribution. Furthermore the single-sideband property of VSB format can assist linear equalization by electronic processing. The transmission performance is accurately evaluated based on the eye opening using a fast statistical method based on an equivalent Gaussian probability density distribution (pdf) which is derived from multiple peaks pdf of distorted eye diagram.     

Magnetic and microwave absorbing properties of magnetite-thermoplastic natural rubber nanocomposites

Magnetic and microwave absorbing properties of thermoplastic natural rubber (TPNR) filled magnetite (Fe₃O₄) nanocomposites were investigated. The TPNR matrix was prepared from polypropylene (PP), natural rubber (NR) and liquid natural rubber (LNR) in the ratio of 70:20:10 with the LNR as the compatibilizer. TPNR-Fe₃O₄ nanocomposites with 4-12 wt% Fe₃O₄ as filler were prepared via a Thermo Haake internal mixer using a melt-blending method. XRD reveals the presence of cubic spinel structure of Fe₃O₄ with the lattice parameter of a=8.395 Å. TEM micrograph shows that the Fe₃O₄ nanoparticles are almost spherical with the size ranging 20-50 nm. The values of saturation magnetization (M_S), remanence (M_R), initial magnetic susceptibility (χ_i) and initial permeability (μ_i) increase, while the coercivity (H_C) decreases with increasing filler content for all compositions. For nanocomposites, the values of the real (ε_r′) and imaginary permittivity (ε_r′′) and imaginary permeability (μ_r′′) increase, while the value of real permeability (μ_r′) decreases as the filler content increases. The absorption or minimum reflection loss (R_L) continuously increases and the dip shifts to a lower frequency region with the increasing of both filler content in nanocomposites and the sample thickness. The R_L is −25.51 dB at 12.65 GHz and the absorbing bandwidth in which the R_L is less than −10 dB is 2.7 GHz when the filler content is 12 wt% at 9 mm sample thickness.     

Influence of laser power on the orientation and microstructure of CeO2 films deposited on Hastelloy C276 tapes by laser chemical vapor deposition

CeO₂ films were prepared on LaMnO₃/MgO/Gd₂Zr₂O₇ multi-coated Hastelloy C276 tapes by laser chemical vapor deposition at different laser power (P_L) from 46 to 101 W. Epitaxial (1 0 0) CeO₂ films were prepared at P_L = 46-93 W (deposition temperature, T_dep = 705-792 K). Epitaxial CeO₂ films had rectangular-shaped grains at P_L = 46-77 W (T_dep = 705-754 K), while square-shaped grains were obtained at P_L = 85-93 W (T_dep = 769-792 K). CeO₂ films showed a columnar microstructure. Epitaxial (1 0 0) CeO₂ films with rectangular grains exhibited full width at half maximum of ω-scan on (2 0 0) reflection and ?-scan on (2 2 0) reflection of 3.4-3.2° and 6.0-7.2°, respectively. The deposition rate of the epitaxial (1 0 0) CeO₂ films had a maximum of 4.6 μm h⁻¹ at P_L = 77 W (T_dep = 754 K).     

Magnetic and microwave absorbing properties of polyaniline/γ-Fe2O3 nanocomposite

The conducting protonated polyaniline (ES)/γ-Fe₂O₃ nanocomposite with the different γ-Fe₂O₃ content were synthesized by in-situ polymerization. Its morphology, microstructure, DC conductivity and magnetic properties of samples were characterized by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), four-wire-technique, and vibrating sample magnetometer (VSM), respectively. The microwave absorbing properties of the nanocomposite powders dispersing in wax coating with the coating thickness of 2 mm were investigated using a vector network analyzers in the frequency range of 7–18 GHz. The pure ES has shown the absorption band with a maximum absorption at approximately 16 GHz and a width (defined as frequency difference between points where the absorption is more than 8 dB) of 3.24 GHz, when 10% γ-Fe₂O₃ by weight is incorporated , the width is broadened to 4.13 GHz and some other absorption bands appear in the range of 7–13 GHz. The parameter dielectric loss tan δ_e (=ε″/ε′) in the 7–18 GHz is found to decrease with increasing γ-Fe₂O₃ contents with 10%, 20%, 30%, respectively, but magnetic loss tan δ_m (=μ″/μ′) increases with increasing γ-Fe₂O₃ contents. The results show that moderate content of γ-Fe₂O₃ nanoparticles embedded in protonated polyaniline matrix may create advanced microwave absorption properties due to simultaneous adjusting of dielectric loss and magnetic loss.     

Design of a RF window for 170 GHz, 1 MW gyrotron for ECRH application

This paper describes the design of a large sized diamond window for 1 MW, 170 GHz gyrotron. The diameter and the thickness of the diamond window are 80 mm and 1.482 mm, respectively, whose edge is directly cooled by water. The CST microwave studio has been used for the S-parameter, and finite element analysis code ANSYS has been used for the thermal and the structural simulation. The return loss (S₁₁) and insertion loss (S₂₁) of the 170 GHz gyrotron window have been found −39.80 dB and −0.011 dB, respectively. The thermal and structural analysis of RF window the 397 K temperature at disk center and maximum displacement 0.01 mm has been found in the window disk during the thermal analysis.