定量核磁法测定CL-20标准物质中有机杂质的含量

采用定量核磁共振波谱法(qNMR)测定六硝基六氮杂异伍兹烷(CL-20)标准物质中有机杂质的含量。核磁谱图解析证明,主要有机杂质成分为残余溶剂乙酸乙酯和中间体五硝基-乙酰基六氮杂异伍兹烷(MPIW),以不含四甲基硅烷(TMS)的氘代丙酮为溶剂,将六甲基二硅醚的四氯化碳标准溶液加入待测液中作为内标,以其谱峰(δ=0.06)作为内标峰对两种有机杂质进行定量分析。考察了延迟时间和采样次数对准确定量的影响,结果显示为确保定量结果的准确性,延迟时间D_1应不小于20 s,采样次数为32次。采用优化后的实验参数进行纯度分析,测得CL-20标准物质中有机杂质乙酸乙酯和MPIW的质量分数分别为0.03516%和0.156 2%,相对标准偏差(RSD)分别为0.91%和0.86%。     

气相色谱法测定人体血液中乙醇含量的测量不确定度评定

对气相色谱法测定人体血液中乙醇含量的测量不确定度进行评定。人体血液中乙醇含量测量结果的测量不确定度主要来源于相对定量校正因子、检材量、检材中添加内标物叔丁醇的体积、检材中乙醇峰面积的平均值与添加内标物叔丁醇峰面积的平均值之比、无水乙醇的纯度及密度等参数引起的不确定度。当检材中乙醇的含量为0．915mg／mL时,扩展不确定度为O．030mg/mL(k=2)。     

二醇酯类内给电子体纯度的核磁共振氢谱内标法测定

建立了测定无对照品的新型二醇酯类内给电子体(6#酯、7#酯)纯度的核磁共振氢谱内标测定法。实验以氘代氯仿为溶剂,以苯甲酸甲酯标准物质为内标,设定合适的采样时间和延迟时间,选取适合的内标峰和样品定量峰,方法测定结果的相对标准偏差分别为0.31%和0.37%(n=6),且呈现良好的线性关系。样品经测量后的纯度平均值分别为98.6%和98.4%,与HPLC法测定结果符合。在没有标准对照品的情况下,核磁共振氢谱内标法可用于该二醇酯类内给电子体的纯度测定。     

气相色谱法分析生产过程中的邻甲基苯胺

气相色谱法测定工业生产过程中邻甲基苯胺及其杂质邻硝基甲苯、间甲基苯胺、对甲基苯胺的含量。4种物质的浓度与色谱峰面积呈良好的线性关系,测定结果与标准值基本一致。邻甲基苯胺、邻硝基甲苯、间甲基苯胺、对甲基苯胺的RSD分别为0.0025%、1.4081%、0.9929%、1.1365%,检出限分别为0.065、0.044、0.062、0.056mg/L。     

微柱分离-ICP-MS测定高纯氧化钆中14种稀土杂质

研究了采用自制微柱分离装置分离Gd2O3基体的条件。99．9％以上基体被分离，分离周期为36min。建立了高纯Gd2O3中分离Gd后测定Yb、Lu以及内标补偿法直接测定其它12种稀土杂质的ICP—MS分析方法.定量下限为0．08～0．80μg／g，加标回收率为85％～115％，相对标准偏差为1．1％～8．5％、方法可满足快速测定99．999％ Gd2O3中14种稀土杂质的要求。     

电感耦合等离子体质谱测定高纯金属钐中25种杂质元素

研究建立了电感耦合等离子体质谱(ICP—MS)测定高纯金属钐中14种稀土及11种非稀土杂质的测定方法。考察了钐基体对杂质元素测定的各种干扰影响。对无干扰的杂质元素,采取了直接测量的方式;对有干扰的元素(Nd、Eu、Dy、Ho、Er、Tm),采用标准加入法的方式进行测定。选择内标元素Sc和Cs,有效补偿了由于基体效应带来的测量偏差。方法的检出限为0．012～83μg／L．加标回收率为88．6％～108．0％．测定精密度(RSD)为0．55％～2．53％,方法可满足99．9％纯度的金属钐中朵质元素的分析测定。     

石墨炉原子吸收光谱法测定地质样品中的痕量金

用活性炭吸附,于5％盐酸溶液中用甲基异丁基酮(MIBK)萃取金,采用斜坡升温和热解涂层石墨管技术进行地质样品中痕量金的石墨炉原子吸收光谱法测定,检出限为0．1ng/g。用该方法对标准物质进行测定,结果与标准值相符,测定结果的相对标准偏差为2．0％～6、9％(n=6)。     

二氧化钛中杂质元素ICP-MS法测定的研究

本文报道了用电感耦合等离子质谱（ICP-MS）测定二氧化钛中18种杂质元素的方法。样品用浓硫酸及固体硫酸铵溶解至清亮后,加入内标元素45Sc、115In、205Tl,用内标法直接测定。讨论了二氧化钛的基体效应及钛产生的质谱干扰对测定结果的影响。方法的检出限是0．03～12．0ng／mL,相对标准偏差是1．4～12．5％,加标回收率是92．0％～103％。该法具有简便、快速、灵敏、准确等优点。     

碳酸二甲酯与苯酚酯交换法反应精馏合成碳酸二苯酯的定量分析

采用OV-101毛细管色谱柱分别对碳酸二甲酯与苯酚酯交换法反应精馏塔底产物和塔顶馏分进行了定量分析。以苯甲酸乙酯为内标物,一次性同时分析了塔釜产物中各组分含量。碳酸二甲酯、碳酸二苯酯和苯甲醚与内标物的峰面积比与各标准品的质量百分比浓度呈良好的线性关系,回归方程分别为Y=48．92X＋0．69、Y=32．82X-1．75和Y=13．17X＋0．07,相关系数分别为0．9976,0．9972和0．9978;以丙酮为内标,对塔顶馏分进行了定量分析。DMC的回归方程为Y=150．57X＋0．37,相关系数为0．9985;甲醇的回归方程为Y=71.20X-0.07,相关系数为0．9996。精密度实验表明,4次平行测定结果重复性良好,各待测物的相对标准偏差都小于2．00％;准确度结果表明,各待测物真实值与测定值的相对标准偏差在0．33％～1．50％之间,该法准确可靠。     

气相色谱法直接分析生物质水解产物中的乙酰丙酸

建立了气相色谱法直接分析生物质水解产物中乙酰丙酸的新方法。结果表明：以苯甲酸为内标物,在FFAP毛细管柱上生物质水解产物有较好的分离效果,同时乙酰丙酸峰形较好：对同一果糖水解液测定的相对标准偏差为0．45％(n=5);标准加样回收率为94．3％～100．5％。该法具有操作简单、快速,结果准确、重现性好等优点。     

Development of a sensitive surface plasmon resonance immunosensor for detection of 2,4-dinitrotoluene with a novel oligo (ethylene glycol)-based sensor surface

A surface plasmon resonance (SPR) immunosensor for detection of 2,4-dinitrotoluene (2,4-DNT), which is a signature compound of 2,4,6-trinitrotoluene-related explosives, was developed by using a novel oligo (ethylene glycol) (OEG)-based sensor surface. A rabbit polyclonal antibody against 2,4-DNT (anti-DNPh-KLH-400 antibody) was prepared, and the avidity for 2,4-DNT and recognition capability were investigated by indirect competitive ELISA. The sensor surface was fabricated by immobilizing a 2,4-DNT analog onto an OEG-based self-assembled monolayer formed on a gold surface via an OEG linker. The fabricated surface was characterized by Fourier-transform infrared-refractive absorption spectrometry (FTIR-RAS). The immunosensing of 2,4-DNT is based on the indirect competitive principle, in which the immunoreaction between the anti-DNPh-KLH-400 antibody and 2,4-DNT on the sensor surface was inhibited in the presence of free 2,4-DNT in solution. The limit of detection for the immunosensor, calculated as three times the standard deviation of a blank value, was 20 pg mL⁻¹, and the linear dynamic range was found to be between 1 and 100 ng mL⁻¹. Additionally, the fabricated OEG-based surface effectively prevented non-specific adsorption of proteins, and the specific response to anti-DNPh-KLH-400 antibody was maintained for more than 30 measurement cycles.     

Studies of Solvent Effects on Structure and Low Frequency Vibrational Spectra of 2,4-Dinitrotoluene

Solvent effects on 2,4-dinitrotoluene(2,4-DNT) molecule in different solvents(toluene,ethanol,and water) were studied via DFT PCM method at B3LYP/6-311+G(d,p) level. The influences of these solvents on the molecular structure,vibrational spectra,charge distribution,and dipole moment were studied as well. The results show that PCM computations are successful in describing the vibrational spectra of 2,4-DNT molecules in these solutions and the solvent effects on the low frequency vibrational spectra are weak.     

Development of imprinted materials for the selective extraction of nitroaromatic explosives

Molecularly imprinted sorbents were synthesized and used as selective extraction sorbents for the analysis of nitroaromatic explosives. Their synthesis by radical polymerization using organic monomers and by sol–gel approach using organosilanes was considered to develop a selective sorbent. The sol–gel approach with phenyltrimethoxysilane (PTMS) as monomer and 2,4-dinitrotoluene (2,4-DNT) as template gave the most promising results. An optimized procedure adapted to the selective treatment of aqueous samples was then developed and applied to various target explosives. For the first time four nitroaromatic compounds were retained on the molecularly imprinted silica (MIS) with extraction recoveries between 29% and 81%, while only low recoveries were obtained on the non-imprinted sorbent, thus highlighting the high degree of selectivity. The MIS was then used for the clean-up of a sample containing motor oil spiked with 2,4-DNT and 2,4,6-trinitrotoluene (2,4,6-TNT). The results were compared with those obtained using a conventional sorbent (Oasis HLB). The cleanest chromatogram obtained using the MIS emphasized the high potential of the MIS as selective sorbent.     

Electrochemical degradation of 2,4-Dinitrotoluene (DNT) from aqueous solutions using three-dimensional electrocatalytic reactor (3DER): Degradation pathway,evaluation of toxicity and optimization using RSM-CCD

2,4-Dinitrotoluene (2,4-DNT) has been found to be an important petrochemical compound, which is primarily employed for the synthesis of tolylene diisocyanate and the production of dyes, rubber, and explosives. Since this compound has high toxicity and carcinogenicity, the cautions should be considered when wastewater contaminated with DNTs and their derivatives is released into the environment. Thus, the object of the present study was the investigation of the 2,4-DNT degradation efficiency using the three-dimensional electrocatalytic reactor (3DER) with two different types of particle electrodes (granular activated carbon (GAC) and magnetized clinoptilolite zeolite (MCZ)@Fe₃O₄ nanoparticles)). Preparation of the graphite (G)/β-PbO₂ anode was done by electrochemically depositing PbO₂ layers on graphite sheets. The prepared graphite sheet and a stainless-steel 316 sheet (with the same dimensions) were employed as the anode and the cathode, respectively. Field emission scanning electron microscopy (FESEM), X-ray diffraction analysis (XRD), and energy-dispersive X-ray spectroscopy mapping (EDS-mapping) confirmed the successful preparation of G/β-PbO₂ anode. The surface morphology, chemical composition of MCZ@Fe₃O₄ nanoparticles as a particle electrode were determined by scanning electron microscope (SEM) and XRD pattern. To determine the optimal conditions, we employed the response surface methodology-based central composite design (RSM-CCD) method. According to observed results, higher efficiency of 3DER was obtained by increasing the reaction time and current density and decreasing pH and the pollutant concentration. Studies highlighted the initial 2,4-DNT concentration of 23.5 mg/L, current density 4.8 mA/cm², pH of 4.1, electrolysis time of 50 min, particle electrodes dose = 6 g/250 cc as optimum values of parameters. The 2,4-DNT degradation efficiencies using GAC and MCZ@Fe₃O₄ nanoparticles as particle electrodes under mentioned optimal conditions were 98.6% and 96.5%, respectively. Moreover, the chemical oxygen demand (COD) and total organic carbon (TOC) removal efficiencies were 88.5% and 80.9% at the end of 50 min, respectively. Furthermore, results were indicative of an enhancement in average oxidation state (AOS) (from 1.27 to 2.36) and carbon oxidation state (COS) (from 1.27 to 3.68) in the 3DER process and a reduction in the COD/TOC ratio (from 1.81 to 1.09); these signposts the effectiveness of 3DER system for providing the biodegradability of 2,4-DNT. Considering the results, the 3DER could lead to suitable results for the degradation of wastewater containing DNT and resistant contaminants as pretreatment and has remarkable applicability for enhancing the biodegradability of wastewater.     

固相微萃取-气相色谱法测定工业苯酚中的2-甲基苯并呋喃和2,4-二苯基-4-甲基-1-戊烯

建立了工业苯酚中有机杂质的固相微萃取-气相色谱(SPME-GC)分析方法。实验考察了SPME萃取温度和萃取时间的影响,同时也优化了热解吸时间。优化后的萃取温度为20 ℃,萃取时间为10 min,热解吸时间为30 s。使用此法对工业苯酚样品中的两种主要有机杂质进行了分析检测,结果表明: 2-甲基苯并呋喃和2,4-二苯基-4-甲基-1-戊烯分别在0.05～1.06 mg/L和0.05～0.99 mg/L范围内线性关系良好(r2分别为0.990和0.992),检出限分别为0.5和1.6 μg/L。在0.1 mg/L的添加水平下,2-甲基苯并呋喃和2,4-二苯基-4-甲基-1-戊烯的回收率分别为104%和113%。该方法具有简单、快速、灵敏度高等优点,适合于工业苯酚中这两种主要痕量有机杂质的准确定量分析。     

Metabolism of 2,4-dinitrotoluene and 2,6-dinitrotoluene, and their dinitrobenzyl alcohols and dinitrobenzaldehydes by Wistar and Sprague-Dawley rat liver microsomal and cytosol fractions

The metabolism of 2,4-dinitrotoluene (2,4-DNT), 2,4-dinitrobenzyl alcohol (2,4-DNB), 2,4-dinitrobenzaldehyde (2,4-DNBAl), 2,6-DNT, 2,6-DNB and 2,6-DNBAl in the microsomal and cytosol fractions prepared from unfortified male Wistar and male Sprague-Dawley (S.D.) rat livers was investigated. Data obtained by high-performance liquid chromatography (HPLC) indicated that the products of dinitrotoluenes (2,4-DNT and 2,6-DNT), dinitrobenzyl alcohols (2,4-DNB and 2,6-DNB), and dinitrobenzaldehydes (2,4-DNBAl and 2,6-DNBAl) in the microsomal and cytosol preparations containing nicotinamide adenine dinucleotide phosphate (NAD(P] and reduced NAD(P)(NAD(P)H) were dinitrobenzyl alcohols (2,4-DNB and 2,6-DNB), dinitrobenzaldehydes (2,4-DNBAl and 2,6-DNBAl), and dinitrobenzoic acids (2,4-DNBA and 2,6-DNBA), and dinitrobenzyl alcohols (2,4-DNB and 2,6-DNB), respectively. From these results, it was concluded that the dinitrobenzaldehydes (2,4-DNBAl and 2,6-DNBAl) were intermediates in the oxidations of dinitrobenzyl alchols (2,4-DNB and 2,6-DNB) to dinitrobenzoic acids (2,4-DNBA and 2,6-DNBA), and that the oxidations of dinitrobenzyl alcohols (2,4-DNB and 2,6-DNB) to dinitrobenzaldehydes (2,4-DNBAl and 2,6-DNBAl) and the reductions of dinitrobenzaldehydes to dinitrobenzyl alcohols (2,4-DNB and 2,6-DNB) were reversible.(ABSTRACT TRUNCATED AT 250 WORDS)     

Effects of Nitrobenzenes on DNA Damage in Germ Cells of Rats

IntroductionSince nitroaromatic compounds constitute a classof industrial chemicals that are present in China andprobably in many other industrialized countries as well,it is necessary to gain insight into their potential hazardto organisms.In recent year…     

Sorption of nitroaromatic compounds to synthesized organoclays

This project quantifies the ability of seven engineered organoclays to sorb TNT and two of its reduction products: 2-amino-4,6-dinitrotoluene (2-A-4,6-DNT) and 4-amino-2,6-dinitrotoluene (4-A-2,6-DNT). The organoclays used in the TNT sorption studies were synthesized in the laboratory by combining bentonite with benzyltriethylammonium chloride (BTEA) at 50, 75, and 100% of the bentonite's cation exchange capacity and with hexadecyltrimethylammonium bromide (HDTMA) at 25, 50, 75, and 100% of the bentonite's cation exchange capacity. For sorption of 2-A-4,6-DNT and 4-A-2,6-DNT, two organoclays were tested: BTEA at 50% CEC and HDTMA at 75% CEC. Sorption data with HDTMA organoclay and TNT were fit to linear isotherms and demonstrated that the clay's sorptive capacity increased as the amount of total organic carbon exchanged onto the clay increased. Sorption data with BTEA organoclay and TNT were fit to Langmuir isotherms; however, the clay's sorptive capacity increased as the amount of total organic carbon sorbed to the clay's surface was decreased. Sorption behavior for TNT reduction products 2-A-4,6-DNT and 4-A-2,6-DNT to one HDTMA organoclay and one BTEA organoclay demonstrated that HDTMA organoclay at 10.3% total organic carbon was a more effective sorbent than BTEA organoclay at 5.2% total organic carbon.     

Impurity identification and determination for the peptide hormone angiotensin I by liquid chromatography–high-resolution tandem mass spectrometry and the metrological impact on value assignments by amino acid analysis

It is common practice to quantify the mass concentration of a peptide solution through quantitative determination of selected chemically stable amino acids produced following complete hydrolysis of the parent peptide. This is because there is generally an insufficient quantity of material available to allow for the obvious alternative of a direct purity analysis characterization of the parent peptide, and the subsequent constitution of a calibration solution. However, selected accurately characterized pure peptide reference materials are required to establish reference points for the dissemination of metrologically traceable measurements and to develop reference measurement systems for laboratory medicine. In principle, purity assignment of a peptide can be performed by using the so-called mass balance approach, by employing a range of analytical techniques to obtain an estimate of the mass fraction content of all impurities present in the intact peptide, and by utilizing the difference from the theoretical limit value to assign the mass fraction content of the main peptide. Liquid chromatography–high-resolution tandem mass spectrometry (LC-hrMS/MS) is a key technique for the detection, identification, and determination of structurally related impurities present in a peptide material, and experiments characterizing the model peptide hormone angiotensin I (ANG I) are described in the present work. Degradation products that were generated from ANG I after storage at elevated temperatures were screened. The formation of peptide fragments such as ANG II or ANG III was determined by comparison of measured mass values with calculated mass values. The use of a data-dependent acquisition technique enabled the detection and structural characterization of ANG II and other peptide fragments as major impurities in the same LC-hrMS/MS analysis run. Subsequent quantification using external calibration allowed the mass fraction of the major impurities in a candidate reference material to be estimated as 10.4 mg/g. Failure to correct for these impurities would lead to a 1 % error in the determination of the concentration of the peptide in solution by amino acid analysis techniques.