Microwave activation of electrochemical processes: enhanced PbO2 electrodeposition, stripping and electrocatalysis

Microwave activation of electrochemical processes has recently been introduced as a new technique for the enhancement and control of processes at electrode|solution (electrolyte) interfaces. This methodology is extended to processes at glassy carbon and boron-doped diamond electrodes. Deposition of both Pb metal and PbO₂ from an aqueous solution of Pb²⁺ (0.1 M HNO₃) are affected by microwave radiation. The formation of PbO₂ on anodically pre-treated boron-doped diamond is demonstrated to change from kinetically sluggish and poorly defined at room temperature to nearly diffusion controlled and well defined in the presence of microwave activation. Calibration of the temperature at the electrode|solution (electrolyte) interface with the Fe^3+/2+ (0.1 M HNO₃) redox system allows the experimentally observed effects to be identified as predominantly thermal in nature and therefore consistent with a localized heating effect at the electrode|solution interface. The microwave-activated deposition of PbO₂ on boron-doped diamond remains facile in the presence of excess oxidizable organic compounds such as ethylene glycol. An increase of the current for the electrocatalytic oxidation of ethylene glycol at PbO₂/boron-doped diamond electrodes in the presence of microwave radiation is observed. Preliminary results suggest that the electrodissolution of solid microparticles of PbO₂ abrasively attached to the surface of a glassy carbon electrode is also enhanced in the presence of microwave radiation. Electronic Publication     

Microwave activation in ionic liquids induces high temperature-high speed electrochemical processes

Self-focusing of intense microwave radiation at the tip of a 25 microm diameter platinum disk microelectrode immersed into the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM(+)PF(6)(-)) containing 1 mM ferrocene causes dramatically (two orders of magnitude) enhanced voltammetric current signals and temperatures in excess of 600 K (at the electrode surface)--extreme conditions sufficient for condensed phase pyrolysis processes to occur.     

Microwave enhanced electroanalysis of formulations: processes in micellar media at glassy carbon and at platinum electrodes

The direct electroanalysis of complex formulations containing alpha-tocopherol (vitamin E) is possible in micellar solution and employing microwave-enhanced voltammetry. In the presence of microwave radiation substantial heating and current enhancement effects have been observed at 330 microm diameter glassy carbon electrodes placed into a micellar aqueous solution and both hydrophilic and highly hydrophobic redox systems are detected. For the water soluble Fe(CN)(6)(3-/4-) redox system in micellar aqueous solutions of 0.1 M NaCl and 0.1 M sodium dodecylsulfate (SDS) at low to intermediate microwave power, thermal effects and convection effects are observed. At higher microwave power, thermal cavitation is induced and dominates the mass transport at the electrode surface. For the micelle-soluble redox systems tert-butylferrocene and 2,5-di-tert-butyl-1,4-benzoquinone, strong and concentration dependent current responses are observed only in the presence of microwave radiation. For the oxidation of micelle-soluble alpha-tocopherol current responses at glassy carbon electrodes are affected by adsorption and desorption processes whereas at platinum electrodes, analytical limiting currents are obtained over a wide range of alpha-tocopherol concentrations. However, for the determination of alpha-tocopherol in a commercial formulation interference from proteins is observed at platinum electrodes and direct measurements are possible only over a limited concentration range and at glassy carbon electrodes.     

Multi-walled carbon nanotubes as electrode materials for electrochemical studies of organometallic compounds in organic solvent media

Abstract  

Films of vertically aligned multi-walled carbon nanotubes (MWCNT) were selectively synthesized on silicon dioxide substrate by catalytic chemical vapor deposition using either benzene or acetonitrile as carbon source and ferrocene (1% w/w) as catalyst. The MWCNT were extensively characterized by using scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, and Raman spectroscopy. In order to examine the prospective application of the fabricated MWCNT films for the detection of electro-active compounds in organic solvent media, electrochemical studies of the oxidation of cobaltocene (CoCp₂) to cobaltocenium cation (CoCp₂⁺) (Cp = cyclopentadienyl anion) in acetonitrile were performed on these films. For this purpose, cyclic voltammetry and electrochemical impedance spectroscopy were employed. The electrochemical parameters for the CoCp₂^+/0 couple in acetonitrile were derived and compared with those obtained using a conventional glassy carbon electrode. The results demonstrate that the synthesized MWCNT films are promising electrode materials for the electrochemical detection of electro-active species in organic solvents. The MWCNT film formed upon decay of benzene has higher capacitance, less Warburg impedance, and less charge transfer resistance, and consequently it provides faster electron transfer kinetics.     

Microwave-enhanced electrochemical processes in micellar surfactant media

High intensity microwave radiation effects are demonstrated for electron transfer processes at 25 or 50-μm diameter platinum electrodes immersed in micellar sodium dodecylsulfate (SDS) solutions. First, a solution containing 2 mM Fe(CN)₆³⁻ and 2 mM Fe(CN)₆⁴⁻ in aqueous 0.1 M NaCl with and without SDS is employed to calibrate the electrode temperature and mass transport conditions. Addition of 0.1 M SDS has only a small effect on the microwave enhanced voltammetry for the Fe(CN)₆^3-/4− system. Next, two highly water-insoluble redox systems are studied. A solution of 1 mM tert-butylferrocene in aqueous 0.1 M NaCl containing 0.1 M SDS is shown to give no current response in the absence of microwaves. In the presence of focused microwaves at a platinum disc electrode, a strong current for the one electron oxidation of tert-butylferrocene is detected presumably due to localized disruption of the micellar solution. Concentrations of tert-butylferrocene down to the micromolar level are detected. α-Tocopherol, a lipophilic vitamin and antioxidant, is soluble in aqueous 0.1 M SDS/0.1 M NaCl. In the presence of microwave radiation, a strong and concentration dependent anodic current response consistent with the two-electron oxidation of α-tocopherol is observed. A heptode array of seven individual 50 μm diameter platinum microelectrodes placed in ca. 720 μm distance of each other is shown to allow microwave enhanced currents to be increased sevenfold with each electrode exhibiting the same microwave effect.     

Microwave activation of catalysts and catalytic processes

The results obtained by using microwave activation in catalytic processes such as the conversion of lower alkanes, the removal of volatile organic compounds and sulfur- and nitrogen-containing compounds from air, and the hydrogenation of aromatic compounds and dehydrogenation of naphthenes are discusses.     

Stability of immobilized soybean lipoxygenase in selected organic solvent media

The immobilization and biocatalysis of commercially purified soybean lipoxygenase (LOX) type I-B (EC 1.13.11.12) were investigated in organic solvent media. The results showed that the highest immobilization efficiencies of LOX, 30.6 and 29.3%, were obtained with DEAE-cellulose and modified Eupergit C250L supports, respectively. The biocatalysis of free and immobilized (Eupergit C250L/EDA) LOXs was investigated in different mixtures of hexane and a selected cosolvent (95:5 [v/v]). The results showed a 1.5 and a 1.6 increase in the activity of free and immobilized LOXs, respectively, using a mixture of hexane and 1,4-dioxane compared with that in hexane alone; however, cosolvents, including 2-octanone, 2-heptanone, 2-butanone, and cyclohexanone, displayed an inhibitory effect on LOX activity. In the mixture of 1,4-dioxane and hexane, LOX activity was dependent on the cosolvent concentration, which was increased with 1,4-dioxane up to 5% (v/v). The threshold 1,4-dioxane concentration (C50) and the incubation period (T50) at which 50% of the maximal enzyme activity was obtained for the free and immobilized LOXs were 6.7 and 8.9% (v/v) and 9.1 and 17.0 min, respectively.     

Unique solvent effects on selective electrochemical fluorination of organic compounds

Recent studies on solvent effects on electrochemical partial fluorination are reviewed. At first, the historical background and some problems of electrochemical fluorination in organic solvents like acetonitrile (MeCN) are briefly mentioned. Ethereal solvents like dimethoxyethane (DME) and a mixture of DME and MeCN were found to improve both the yield and current efficiency for electrochemical fluorination since these solvent systems effectively suppress anode passivation and overoxidation of fluorinated products once formed during the electrolysis. It was also found that DME stabilizes radical cationic intermediates of 4-arylthio-1,3-dioxolan-2-ones and 3-phenylthiophthalide leading to α-fluorination while dichloromethane (CH₂Cl₂) destabilizes them leading to fluorodesulfurization. On the other hand, imidazolium ionic liquids and liquid fluoride salts like Et₄NF·4HF and Et₃N·5HF exhibited similar effects to CH₂Cl₂. Selective fluorination of hardly oxidizable phthalide was also achieved using a combination of two kinds of ionic liquids (imidazolium triflate and liquid fluoride salts).     

Microwave activation of the electro-oxidation of glucose in alkaline media

The oxidation of glucose is a complex process usually requiring catalytically active electrode surfaces or enzyme-modified electrodes. In this study the effect of high intensity microwave radiation on the oxidation of glucose in alkaline solution at Au, Cu, and Ni electrodes is reported. Calibration experiments with the Fe(CN)(6)(3-/4-) redox system in aqueous 0.1 M NaOH indicate that strong thermal effects occur at both 50 and 500 microm diameter electrodes with temperatures reaching 380 K. Extreme mass transport effects with mass transport coefficients of k(mt) > 0.01 m s(-1)(or k(mt) > 1.0 cm s(-1)) are observed at 50 microm diameter electrodes in the presence of microwaves. The electrocatalytic oxidation of glucose at 500 microm diameter Au, Cu, or Ni electrodes immersed in 0.1 M NaOH and in the presence of microwave radiation is shown to be dominated by kinetic control. The magnitude of glucose oxidation currents at Cu electrodes is shown to depend on the thickness of a pre-formed oxide layer. At 50 microm diameter Au, Cu, or Ni electrodes microwave enhanced current densities are generally higher, but only at Au electrodes is a significantly increased rate for the electrocatalytic oxidation of glucose to gluconolactone observed. This rate enhancement appears to be independent of temperature but microwave intensity dependent, and therefore non-thermal in nature. Voltammetric currents observed at Ni electrodes in the presence of microwaves show the best correlation with glucose concentration and are therefore analytically most useful.     

Dispersion stability in mixed solvent (aqueous/organic) media

The dependence of critical coagulation concentrations and zeta potentials on composition for polystyrene latex particles in n-alkanol/water and urea/water mixtures are compared. Similar data from other authors are also reviewed.     

Direct and indirect electrochemical reduction of organic halides in aprotic media

Cyclic voltammetric reduction of 17 different organic halides including alkyl, allyl, and benzyl chlorides, bromides, and iodides in aprotic media (DMF, DMSO, and acetonitrile, AN), containing 0.1 M Bu₄NClO₄, have been reported at glassy carbon (gc) and graphite as working electrodes. A single two-electron irreversible and diffusion-limited reduction of the carbon-halogen bond is observed, the reduction potentials ranging from –1.20 to –2.70 V (versus silver wire quasireference electrode) depending on the halide, the solvent, and the electrode. Indirect reduction of these 17 halides, however, is effected at much lower potentials (–0.79 to –0.92 V versus SCE) depending on the experimental conditions by in situ electrogenerated superoxide ion (O ₂ ^– ) by CPE. The products have been characterized by TLC, GC, CV, or chemical estimation. The diorganic peroxide and the organic hydroperoxide were the major products. In case of tertiary alkyl halides, however, alkenes predominated, due to basic nature of O ₂ ^– in these reactions. These studies indicate sufficient strength of O ₂ ^– as a nucleophile or base depending on the experimental conditions.From Elektrokhimiya, Vol. 41, No. 3, 2005, pp. 350–355.Original English Text Copyright © 2005 by Vasudevan.This article was submitted by the author in English.     

Lipase-catalyzed esterification of selected phenolic acids with linolenyl alcohols in organic solvent media

Lipase-catalyzed esterification of selected phenolic acids with linolenyl alcohols was investigated in selected organic solvent media. The enzyme activity for the esterification of dihydrocaffeic acid with linolenyl alcohol in solvent mixtures of hexane/2-butanone of 75∶25 (v/v) and 65∶35 (v/v) was 0.88 and 0.47 μmol of esterified dihydrocaffeic acid/(g of solid enzyme·min), respectively, with a corresponding esterification yield of 76 and 58%, respectively. However, the esterification of ferulic acid with linolenyl alcohol in the reaction medium of hexane/2-butanone of 65∶35 (v/v) resulted in a low yield (16%). Using the reaction medium of hexane/2-butanone of 75∶25 (v/v), an increase in linolenyl alcohol concentration with a concomitant use of a constant amount of dihydrocaffeic acid resulted in an increase in esterification yield. The highest esterification yield of 99% was obtained with a ratio of dihydrocaffeic acid to linolenyl alcohol of 1∶8 after 7 d of reaction. Biosynthesis of the end product, linolenyl dihydrocaffeate, was confirmed by electrospray ionization mass spectroscopy structural analysis; the esterproduct demonstrated an antiradical activity close to that of α-tocopherol.     

Micellar enhanced cyanide ion determination in samples from synthetic organic processes

A method was developed for the recovery and determination of cyanide ion in organic sample matrices. To facilitate the solubilization of cyanide ions, cetyltrimethylammonium bromide (CTAB) was added at concentrations above the critical micelle concentration. Sample cyanation reaction products consisted of solvent mixtures of a hydroxynitrile in DMF-toluene or DMF-isopropylacetate (IPAC). Spectrophotometric determination of cyanide ion at 578 nm by the pyridine-barbituric acid method was automated by flow injection analysis. Recovery of cyanide ion from spiked samples was 93.2% in DMF-IPAC solvent matrix and 93.9% in DMF-toluene. Low alkali concentration was observed to favor solubilization of cyanide ion in the micellar solution.     

On the action of organic solvent in the new B-Z oscillator in aqueous-organic mixed media

The author pointed out that hydrolysis of acetonitrile, trace impurity of someorganic solvents, and insolubility of benzene can make great effects on B-Z or B-R oscillators in aqueous-organic mixed media. And surfactant is better than organic solvent in the design of chemical oscillators with insoluble substance as substrate. © 1995 John Wiley & Sons, Inc.     

The electrochemical advanced oxidation processes coupling of oxidants for organic pollutants degradation: A mini-review

The electrochemical advanced oxidation processes(EAOPs) have been extensively applied in the treatment of organic pollutants degradation.Herein,the mini review provides the coupling systems about EAOPs and different oxidants(e.g.,persulfate(PS),peroxymonosulfate(PMS),and ozone(O_3)),including EAOPs-PS systems,EAOPs-PMS systems,EAOPs-peroxone systems,and photoelectro-oxidants systems,for the organic compounds degradation.The coupling system of EAOPs with oxidants is an effective way to improve the generated free radicals(e.g.,HO~·and SO_4~(·-)) concentration and to accelerate pollutant degradation.In this review,we make a summary of the homogeneous and heterogeneous EAOPs-oxidant processes.The reaction mechanisms of EAOPs combined with different oxidants are elucidated in detail,as well as the synergistic effect for improving the degradation and mineralization efficiency.     

Surface plasmon modes of gold nanospheres, nanorods, and nanoplates in an organic solvent: phase-transfer from aqueous to organic media

We present a process for the phase-transfer of gold nanoparticles from an aqueous to an organic medium with normal alkanethiols. This method can be applied not only to large nanospheres (d~100 nm) but also to anisotropic nanoparticles like nanorods and nanoplates. It allows the comparison of the nanoparticle optical properties when they are dispersed in both aqueous and organic media.     

The electrochemical advanced oxidation processes coupling of oxidants for organic pollutants degradation: A mini-review

In this mini-review, the homogeneous and heterogeneous EAOPs-oxidant processes were summarized. The reaction mechanisms of different EAOPs combined with different oxidants are elucidated in detail, as well as the synergistic effect for improving the treatment efficiency.     

Evanescent wave broadband cavity enhanced absorption spectroscopy using supercontinuum radiation: A new probe of electrochemical processes

An evanescent wave variant of broadband cavity enhanced absorption spectroscopy using a supercontinuum light source has been used to detect electrogenerated species at the silica-water interface. In proof-of-concept experiments [IrCl₆]²⁻ was produced by electro-oxidation of [IrCl₆]³⁻ in a thin layer electrochemical cell. Diffusion of the Ir(IV) across the cell to a silica interface was monitored yielding real-time concentrations within an evanescent field region at the interface. The optical response was compared with the electrochemical response during chronoamperometric step and cyclic voltammetric experiments and both were simulated by finite element modeling. The experiment is highly sensitive to interfacial processes and its wide spectral width and fast time resolution make it a potentially powerful tool for in situ spectroscopic monitoring of processes and intermediates in dynamical electrochemistry.     

The electroanalytical detection and determination of copper in heavily passivating media: ultrasonically enhanced solvent extraction by N-benzoyl-N-phenyl-hydroxylamine in ethyl acetate coupled with electrochemical detection by sono-square wave stripping voltammetry analysis.

N-benzoyl-N-phenyl-hydroxylamine dissolved in ethyl acetate was employed as a ligand for the solvent extraction of copper. Ultrasonic emulsification was shown to be effective both in the extraction of copper from an aqueous phase into ethyl acetate and its recovery or "back extraction" into a fresh clean aqueous solution. Experimental determination of thermodynamic parameters governing the extraction process via UV/visible spectroscopy is reported. This permitted theoretical predictions for the amount of copper transferred into the final aqueous solution to be fitted to experimental data. Quantitative analysis of copper removed via double sono-extraction from an aqueous medium hostile to voltammetric analysis proceeded via sono-square wave anodic stripping voltammetry analysis (sono-SWASV). This resulted in very high sensitivity in the relatively clean medium. The technique was then applied to the analysis of copper in the soft drink 'Ribena Light'. In the absence of sample preparation by solvent extraction sono-SWASV yields a measurable peak current for copper. However it is irreproducible and erratic due to passivating effects, possibly attributed to the sugars, natural flavourings and colourings present. Following sono-solvent extraction, the overall copper concentration could be obtained with a detection limit of 2 microg L(-1). Biphasic sono-extraction synergistically coupled with the recognized technique sono-SWASV presents an attractive technique for copper analysis in electrode passivating media. The technique necessarily removes contaminants present in the test solution since these will prefer to remain in the initial aqueous phase, or will transfer to the organic phase but are unlikely to be doubly transferred into the 'clean' final aqueous phase.