Receptivity of the Swept Wing Boundary Layer to a Steady Flow Inhomogeneity

The boundary layer on a plate with an inclined blunt leading edge is investigated for a free-stream flow with a small span-periodic velocity inhomogeneity. This flow simulates the penetration of the outer turbulence into the swept wing boundary layer. It is shown that the boundary layer perturbations generated by the inhomogeneity generally have a streamwise velocity component significantly greater than the initial inhomogeneity amplitude. The dependence of the perturbations on the distance from the leading edge and the spanwise inhomogeneity period is found. It is shown that the swept wing boundary layer is less sensitive to the perturbation type in question than the straight wing boundary layer.     

Experiments on localized disturbances in a flat plate boundary layer. Part 2. Interaction between localized disturbances and TS-waves

Previous studies on boundary layer transition at moderate levels of free stream turbulence (FST) have shown that the transition process can be promoted by the introduction of Tollmien-Schlichting (TS) waves. In the present work the interaction between localized boundary layer disturbances and controlled TS-waves is studied experimentally. The localized disturbances are generated either from a controlled free stream perturbation, or by means of suction or injection through a slot in the flat plate surface. Both methods result in boundary layer disturbances dominated by elongated streamwise streaks of high and low velocity in the streamwise component. A strong interaction is observed preferably for high frequency TS-waves, which are damped when generated separately, and the interaction starts as a local amplification of a wide band of low-frequency oblique waves. The later stages of the transition process can be identified as a non-linear interaction between the oblique structures, leading to regeneration of new and stronger streamwise streaks.     

Receptivity of the Blunt-Leading-Edge Plate Boundary Layer to Unsteady Vortex Perturbations

The response of the boundary layer on a plate with a blunt leading edge to frozen-in vortex perturbations whose vorticity is normal to the plate surface is found. It is shown that these vortices generate an inhomogeneity of the streamwise velocity component in the boundary layer. This inhomogeneity is analogous to the streaky structure developing as the degree of free-stream turbulence increases. The dependence of the amplitude and shape of the boundary layer inhomogeneity on the distance from the leading edge, the streamwise and spanwise scales, and other parameters is found for periodic and local initial perturbations. It is shown that the receptivity of the boundary layer decreases with increase in the frequency and with decrease in the streamwise perturbation scale.     

Effects of free-stream turbulence on a transitional separated–reattached flow over a flat plate with a sharp leading edge

The transitional separated–reattached flow on a flat plate with a blunt leading edge under 2% free-stream turbulence (FST) is numerically simulated using the Large-eddy simulation (LES) approach. The Reynolds number based on the free-stream velocity and the plate thickness is 6500. A dynamic subgrid-scale model is employed and the LES results compare well with the available experimental data.It is well known that FST enhances shear-layer entrainment rates, reduces the mean reattachment distance, and causes early transition to turbulence leading to an early breakdown of the separated boundary layer. Many experimental studies have shown that different vortex shedding frequencies exist, specially the so called low-frequency flapping when there is a separation bubble but its mechanism is still not completely understood. The previous study by us without free-stream turbulence (NFST) did not show the existence of such a low-frequency flapping of the shear layer and it is not clear what the effects of FST will have on these shedding modes. Detailed analysis of the LES data has been presented in the present paper and the low-frequency flapping has not been detected in the current study.     

Extension of an algebraic intermittency model for better prediction of transition in separated layers under strong free-stream turbulence

A constitutive law describing the Reynolds stresses in boundary layers undergoing laminar-to-turbulent transition, constructed in previous work by elastic-net regression on an experimental data base, is used to improve an algebraic intermittency model for cases with transition in a separated layer influenced by a high level of free-stream turbulence. The intermittency model is combined with a k-ω turbulence model and the basic version, developed in previous work, functions well for bypass transition in attached boundary layers and for transition in separated boundary layers under a low free-stream turbulence level. The basic model version is extended by an additional production term in the transport equation for turbulent kinetic energy. A sensor detects the front part of a separated layer and activates the production term. The term expresses the effect of Klebanoff streaks generated upstream of separation on the Kelvin-Helmholtz instability rolls in the separated part of the layer. The Klebanoff streaks cause faster breakdown by the combined effects of a large adverse pressure gradient and an elevated free-stream turbulence level. The extended model does not alter the results of the basic model version for bypass transition in an attached boundary layer and for transition in a separated boundary layer under a low free-stream turbulence level. The extended model significantly improves the predictions of the previous model version for transition in a separated boundary layer under a high free-stream turbulence level.     

An experimental investigation of unsteady turbulent-wake/boundary-layer interaction

An experimental investigation of unsteady-wake/boundary-layer interaction, similar to that occurring in turbomachinery, has been conducted in a specially modified wind tunnel. Unsteadiness in a turbomachine is periodic in nature, due to the relative motion of rotor and stator blades, resulting in travelling-wave disturbances that affect the blade boundary layers. In the experimental rig, travelling-wave disturbances were generated by a moving airfoil apparatus installed upstream of a flat plate to provide a two-dimensional model of a turbomachine stage. The boundary layer on the flat plate was tripped near the leading edge to generate a turbulent flow prior to interaction with the wakes, and measurements of velocity throughout the boundary layer were taken with a hot-wire probe. The Reynolds number, based on distance along the plate, ranged from 0.144×10⁵ to 1.44×10⁵, and all data were reduced through a process of ensemble averaging. Due to the nonlinear interactions with the boundary layer, the travelling discrete frequency wakes were found to decrease the shape factor of the velocity profile and to increase the level of turbulent fluctuations. Unlike the phase advance found with stationary-wave external disturbances, velocity profiles subject to the travelling wake fluctuations exhibited increasingly negative phase shifts from the free-stream towards the wall.     

Receptivity of the boundary layer on a flat plate with a blunted leading edge to steady nonuniformity of the free stream

The flow past a flat plate with a blunted leading edge by a flow of a viscous incompressible fluid with a small spanwise-periodic, steady nonuniformity of the velocity profile is considered. Such a flow simulates the interaction of one type of vortex disturbances of a turbulent external flow with the boundary layer. The solution obtained predicts generation of strong disturbances in the boundary layer, which are similar to the streaky structure observed in the case of high free-stream turbulence. It is shown that the boundary-layer flow on blunted bodies is more sensitive to vortex disturbances than on a plate with a sharp leading edge. Central Aerohydrodynamic Institute, Zhukovskii, 140160. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 41, No. 4, pp. 93–100, July–August, 2000.     

Optimal disturbances above and upstream of a flat plate with an elliptic-type leading edge

Adjoint-based iterative methods are employed to compute linear optimal disturbances in a spatially growing boundary layer around an elliptic leading edge. The Lagrangian approach is used where an objective function is chosen and constraints are assigned. The optimisation problem is solved using power iterations combined with a matrix-free formulation, where the state is marched forward in time with a standard direct numerical simulation solver and backward with the adjoint solver until a chosen convergence criterion is fulfilled. We consider the global and, more relevant to receptivity studies, the upstream localised optimal initial condition leading to the largest possible energy amplification at time T. We find that the two-dimensional initial condition with the largest potential for growth is a Tollmien–Schlichting-like wave packet that includes the Orr mechanism and is located inside the boundary layer downstream of the leading edge. Three-dimensional optimal disturbances induce streaks by the lift-up mechanism. Requiring the optimal initial condition to be localised upstream of the plate enables us to better study the effects of the leading edge on the boundary layer receptivity mechanisms. Two-dimensional upstream disturbances are inefficient at triggering unstable eigenmodes, whereas three-dimensional disturbances induce streamwise streaks with significant growth.     

From Streaks to Spots and on to Turbulence: Exploring the Dynamics of Boundary Layer Transition

“...an eerie type of chaos can lurk just behind a facade of order, and yet deep inside the chaos lurks an even eerier type of order.” Douglas Hofstadter Bypass transition to turbulence in boundary layers is examined using linear theory and direct numerical simulations (DNS). First, the penetration of low-frequency free-stream disturbances into the boundary layer is explained using a model problem with two time scales, namely the shear and wall-normal diffusion. The simple model provides a physical understanding of the phenomenon of shear sheltering. The second stage in bypass transition is the amplification of streaks. Streak detection and tracking algorithms were applied to examine the characteristics of the streak population inside the boundary layer, beneath free-stream turbulence. It is demonstrated that simple statistical averaging masks the wealth of streak amplitudes in transitional flows, and in particular the high-amplitude, relatively rare events that precede the onset of turbulence. The third stage of the transition process, namely the secondary instability of streaks, is examined using secondary instability analysis. It is demonstrated that two types of instability are possible: An outer instability arises near the edge of the boundary layer on the lifted, low-speed streaks. An inner instability also exists, and has the appearance of a near-wall wavepacket. The stability theory is robust, and can predict the particular streaks which are likely to undergo secondary instability and break down in transitional boundary layers beneath free-stream turbulence. Beyond the secondary instability, turbulent spots are tracked in DNS in order to examine their characteristics in the subsequent non-linear stages of transition. At every stage, we compare the findings from linear theory to the empirical observations from direct solutions of the Navier-Stokes equations. The complementarity between the theoretical predictions and the computational experiments is highlighted, and it leads to a detailed view of the mechanics of transition.     

Large Eddy Simulations in Turbines: Influence of Roughness and Free-Stream Turbulence

The individual and coupled effects of the incoming free-stream turbulence (FST) and surface roughness on the transition of a separated shear layer over a flat plate is numerically investigated using Large eddy simulation (LES). The upper wall of the test section is inviscid and specifically contoured to impose a streamwise pressure distribution over the flat plate to simulate the suction surface of a low pressure turbine (LPT) blade. The interaction of the streamwise streaks due to FST and roughness with the separated shear layer is captured. The streaks induced by FST are intermittent in nature and the streaks due to roughness are steady for a given topology of the rough surface. Both FST and roughness promoted near-wall mixing. The ‘net effect’ of mixing in the pre-separated region is manifested by a shift the inflection point of the velocity profile towards the wall. This resulted in the upstream shift of the transition point and a significant reduction in the size of the separation bubble. The combined effect of FST and roughness further reduced the size of separation bubble. The streamwise evolution of the boundary layer parameters has been compared for different cases. The potential ‘roughness benefit’ obtained in the case of highly loaded turbine blades in terms of its considerable reduction of profile loss is also shown.     

Velocity statistics and flow structures observed in bypass transition using stereo PTV

It is known from smoke visualizations that in a transitional boundary layer subjected to free-stream turbulence, streaks appear and eventually break down to turbulence after wavy motions. In order to observe the streaky structures directly, a stereo particle-tracking velocimetry system using hydrogen bubbles in a water channel has been developed and validated against laser Doppler velocimetry. Mean flow statistics show good agreement with previous results. With the developed measurement system, the instantaneous spanwise distribution of the streamwise and wall-normal velocities can be measured fast enough to resolve the time development of the streaky structures. Measurements of instantaneous spanwise distributions of the streamwise and wall-normal velocity disturbances show strong negative correlation between the wall-normal and streamwise velocities in the streaks. Published online: 19 November 2002     

DNS of heat transfer in transitional, accelerated boundary layer flow over a flat plate affected by free-stream fluctuations

Direct numerical simulations (DNS) of flow over and heat transfer from a flat plate affected by free-stream fluctuations were performed. A contoured upper wall was employed to generate a favourable streamwise pressure gradient along a large portion of the flat plate. The free-stream fluctuations originated from a separate LES of isotropic turbulence in a box. In the laminar portions of the accelerating boundary layer flow the formation of streaks was observed to induce an increase in heat transfer by the exchange of hot fluid near the surface of the plate and cold fluid from the free-stream. In the regions where the streamwise pressure gradient was only mildly favourable, intermittent turbulent spots were detected which relaminarised downstream as the streamwise pressure gradient became stronger. The relaminarisation of the turbulent spots was reflected by a slight decrease in the friction coefficient, which converged to its laminar value in the region where the streamwise pressure gradient was strongest.     

Large eddy simulations in low-pressure turbines: Effect of wakes at elevated free-stream turbulence

The transition of a separated shear layer over a flat plate, in the presence of periodic wakes and elevated free-stream turbulence (FST), is numerically investigated using Large Eddy Simulation (LES). The upper wall of the test section is inviscid and specifically contoured to impose a streamwise pressure distribution over the flat plate to simulate the suction surface of a low-pressure turbine (LPT) blade. Two different distributions representative of a ‘high-lift’ and an ‘ultra high-lift’ turbine blade are examined. Results obtained from the current LES compare favourably with the extensive experimental data previously obtained for these configurations. The LES results are then used to further investigate the flow physics involved in the transition process.In line with experimental experience, the benefit of wakes and FST obtained by suppressing the separation bubble, is more pronounced in ‘ultra high-lift’ design when compared to the ‘high-lift’ design. Stronger ‘Klebanoff streaks’ are formed in the presence of wakes when compared to the streaks due to FST alone. These streaks promoted much early transition. The weak Klebanoff streaks due to FST continued to trigger transition in between the wake passing cycles.The experimental inference regarding the origin of Klebanoff streaks at the leading edge has been confirmed by the current simulations. While the wake convects at local free-stream velocity, its impression in the boundary layer in the form of streaks convects much slowly. The ‘part-span’ Kelvin–Helmholtz structures, which were observed in the experiments when the wake passes over the separation bubble, are also captured. The non-phase averaged space-time plots manifest that reattachment is a localized process across the span unlike the impression of global reattachment portrayed by phase averaging.     

Direct numerical simulation of the transition to turbulence in a supersonic boundary layer on smooth and rough surfaces

Direct numerical simulations of instability development and transition to turbulence in a supersonic boundary layer on a flat plate are performed. The computations are carried out for moderate supersonic (free-stream Mach number M = 2) and hypersonic (M = 6) velocities. The boundary layer development is simulated, which includes the stages of linear growth of disturbances, their nonlinear interaction, stochastization, and turbulent flow formation. A laminar–turbulent transition initiated by distributed roughness of the plate surface at the Mach number M = 2 is also considered.     

Investigation of boundary layer stability in a gradient flow with a high degree of free-stream turbulence

The results of an experimental investigation of boundary layer stability in a gradient flow with a high degree of free-stream turbulence are presented. The question of the possible artificial generation, the further development and the effect on laminar-turbulent transition of instability waves (Tollmien-Schlichting waves) in the boundary layer on a wing profile is considered for a level of free-stream turbulence =1.75% of the free-stream velocity; the sensitivity of the flow to the disturbances and their control by means of boundary layer suction are investigated.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 52–58, March–April, 1990.     

Unsteady Couette flow in a rotating system

The unsteady Couette flow between two infinite horizontal plates induced by the non-torsional oscillations of one of the plates in a rotating system under the boundary layer approximations is investigated. An exact solution of the governing equations has been obtained by using Laplace transform technique. It is shown that when the oscillating plate situated at an infinite distance from stationary plate then the problem reduces to the unsteady boundary layer problem in a rotating system with non-torsional oscillations of the free-stream velocity.     

Flat-Plate Boundary Layer Receptivity to a Steady Free-Stream Vortex Disturbance

A single trailing vortex developed behind a micro-wing immersed in a free stream was used to study the vortex receptivity of the boundary layer on a flat plate. As a result of the interaction, in the boundary layer there develop longitudinal-velocity disturbances which grow almost linearly in the longitudinal coordinate. The parameters of the excited steady disturbances agree with the data of previous experiments performed under natural conditions and dealing with an indirect scenario of laminar-turbulent transition at high free-stream turbulence. It is shown that the leading edge of the plate does not play a decisive role in the mechanism of growth of disturbances of this kind and the receptivity is non-local in nature.     

Experiments on localized disturbances in a flat plate boundary layer. Part 1. The receptivity and evolution of a localized free stream disturbance

The receptivity of a laminar boundary layer to free stream disturbances has been experimentally investigated through the introduction of deterministic localized disturbances upstream of a flat plate mounted in a wind tunnel. Hot-wire measurements indicate that the spanwise gradient of the normal velocity component (and hence the streamwise vorticity) plays an essential role in the transfer of disturbance energy into the boundary layer. Inside the laminar boundary layer the disturbances were found to give rise to the formation of longitudinal structures of alternating high and low streamwise velocity. Similar streaky structures exist in laminar boundary layers exposed to free stream turbulence, in which the disturbance amplitude increases in linear proportion to the displacement thickness. In the present study the perturbation amplitude of the streaks was always decaying for the initial amplitudes used, in contrast to the growing fluctuations that are observed in the presence of free stream turbulence. This points out the importance of the continuous influence from the free stream turbulence along the boundary layer edge.     

Optimal disturbances in suction boundary layers

A well-known optimization procedure is used to find the optimal disturbances in two different suction boundary layers within the spatial framework. The maximum algebraic growth in the asymptotic suction boundary layer is presented and compared to previous temporal results. Furthermore, the spatial approach allows a study of a developing boundary layer in which a region at the leading edge is left free from suction. This new flow, which emulates the base flow of a recent wind-tunnel experiment, is herein denoted a semi-suction boundary layer. It is found that the optimal disturbances for these two suction boundary layers consist of streamwise vortices that develop into streamwise streaks, as previously found for a number of shear flows. It is shown that the maximum energy growth in the semi-suction boundary layer is obtained over the upstream region where no suction is applied. The result indicates that the spanwise scale of the streaks is set in this region, which is in agreement with previous experimental findings.     

DNS of a Laminar Separation Bubble in the Presence of Oscillating External Flow

A three-dimensional Direct Numerical Simulation (DNS) of a laminar separation bubble in the presence of oscillating flow is performed. The oscillating flow induces a streamwise pressure gradient varying in time. The special shape of the upper boundary of the computational domain, together with the oscillating pressure gradient causes the boundary layer flow to alternately separate and re-attach. When the inflow decelerates, the shear layer starts to separate and rolls up. Simultaneously the flow becomes 3D. After a transient period, the phase-averaged reverse flow inside the separation bubble reaches speeds ranging from 20 up to 150% of the free-stream velocity. During these phases, the flow is absolutely unstable and self-sustained turbulence can exist. When the inflow starts to accelerate, a spanwise roll of turbulent flow is shed from the shear layer. Shortly after this, the remainder of the separation bubble moves downstream and rejoins with the shed turbulent roll. During the flow-acceleration phase, a patch of laminar boundary layer flow is obtained. Along the flat plate, a series of turbulent patches of flow travelling downstream, separated by laminar flow can be observed, reminiscent of boundary layer flow in a turbine cascade with periodically appearing free-stream disturbances.