复合催化剂上CO2加氢合成C2烃类

介绍了由CO₂+H₂合成C2⁺烃的几种复合催化剂体系的研究进展，比较和评价了复合催化剂体系的活性和选择性及对C2⁺烃类生成的影响。着重于复合催化剂体系对C4⁺烃的生成及产物分布的影响并简述反应机理。     

H2O2-鲁米诺-荧光素钠-K2CO3高灵敏化学发光法测定二氧化碳

在碱性介质中, CO₃^2－对H₂O₂氧化鲁米诺化学发光反应具有重要作用, 荧光素钠对该反应具有很强的增敏作用. 据此, 建立了化学发光法测定二氧化碳的新方法. 方法的线性范围为1.0×10^－10～5.0×10^－6 mol•L^－1 CO₃^2－, 检出限为 1.2×10^－11 mol•L^－1 CO₃^2－ (相当于5.3×10^－10 g•L^－1 CO₂). 该方法用于室内外空气中二氧化碳含量的测定, 相对标准偏差1.8%～2.1% (n＝11), 加标实验回收率97.6%～101.4%. 论文还探讨了反应的发光机理, 发光反应很可能是由溶液中的CO₃^2－与H₂O₂作用而产生的活性自由基引发, 荧光素钠对发光的增敏作用为化学能量转移过程.     

Isothermal differential scanning calorimetry on an exothermic phenomenon during thermal decomposition of hydromagnesite 4 MgCO3 · Mg(OH)2 · 4 H2O

An exothermic phenomenon and a simultaneous rapid evolution of a small amount of carbon dioxide at ?500°C during thermal decomposition of hydromagnesite 4 MgCO₃ · Mg(OH)₂ · 4 H₂O was studied by isothermal DSCTG in a carbon dioxide atmosphere. It was quantitatively confirmed that the exothermic phenomenon was due to crystallization of MgCO₃ from the amorphous phase and that the evolution of carbon dioxide was due to decomposition of the MgCO₃ by the heat of crystallization (?3.4 kcal mole^?1.     

Magic cluster ion distributions: (NO)3+ (N2O)n and (NO)3+ (CO2)n

Supersonic jet expansions of mixtures of nitric oxide with either nitrous oxide or carbon dioxide have been investigated over a wide range of relative concentrations. Mixed molecular cluster ions of the form (NO) _m ⁺ (N₂O)_n and (NO) _m ⁺ (CO₂)_n are detected following non-resonant two-photon ionization. Over a wide range of intermediate concentrations, the cluster ion distributions (NO) ₃ ⁺ (N₂O)_n and (NO) ₃ ⁺ (CO₂)_n with n30 are significantly more intense than clusters containing other numbers of nitric oxide molecules. The extra abundance of these species is attributed to their especially stable structures and several possible forms are discussed. An intriguing possibility involves a stable cyclic nitric oxide trimer (or ion) when combined with nitrous oxide or carbon dioxide clusters.     

CO2/H2 separation by facilitated transport membranes immobilized with aqueous single and mixed amine solutions: Experimental and modeling study

An experimental and theoretical analysis to separate CO₂ using facilitated transport membranes immobilized with different aqueous single and mixed amine solutions have been performed. The membranes containing monoethanolamine (MEA), diethanolamine (DEA), monoprotonated ethylenediamine (EDAH⁺) and piperazine (PZ), as well as aqueous blends of PZ with MEA, DEA or EDAH⁺ were considered. The aqueous solution of PZ showed the highest CO₂ permeation rate with respect to other single amine solutions. Therefore blends of PZ with MEA, DEA and EDAH⁺ increased the permeance of carbon dioxide through mixed amine membranes.     

Preparation of CuAsF6 and Ni[AsF6]2.2SO2

Arsenic pentafluoride reacts with excess copper in sulphur dioxide to give CuAsF₆. A similar reaction with elemental nickel yields Ni(AsF₆)₂.2SO₂, the structure of which is discussed. The X-ray powder diffraction photograph of CuAsF₆ was indexed on a rhombohedral unit cells a = 5.49±.01Å, α = 55.7±.1°, V = 105.4ų, Z = 1, and is of the same structural type as LiSbF₆ showing that the cuprous ion is octahedrally surrounded by fluorines. Comparison of the unit cell volume of CuAsF₆ with other structurally similar hexafluoroarsenate salts shows that the effective volume of cuprous ion is small indicating substantial anion-cation interaction. Arsenic pentafluoride reacts with Monel in the presence of sulphur dioxide give a mixtures of CuAsF₆ and Ni[AsF₆]₂.2SO₂.     

偏硼酸锶催化剂光催化还原CO2合成CH4

采用溶胶-凝胶法制备出偏硼酸锶(SrB₂O₄)光催化剂. 紫外光催化还原CO₂合成CH₄(在液相水中)的实验证明: SrB₂O₄催化剂的光催化活性略高于TiO₂(P25). 利用X射线电子衍射谱(XRD)、傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、荧光(PL)光谱和紫外-可见(UV-Vis)漫反射吸收光谱等技术, 研究了SrB₂O₄ 催化剂的晶体结构、形貌和能带结构. 结果表明: SrB₂O₄ 的价带为2.07 V (vs normalhydrogen electrode (NHE)), 低于(H₂O/H⁺)的氧化还原电位E_redox^o (0.82 V (vs NHE)); 而导带为-1.47 V (vsNHE), 高于(CO₂/CH₄)的氧化还原电位E_redox^o (-0.24 V (vs NHE)). 因此, SrB₂O₄催化剂可以有效地光催化还原CO₂生成CH₄. 与TiO₂(P25)相比, SrB₂O₄催化剂具有相对较高导带, 光生电子的还原能力强于TiO₂(P25), 更有利于CH₄的生成, 从而决定了SrB₂O₄催化剂光催化还原CO₂合成CH₄具有较高的光催化活性.     

Thermal decomposition of barium oxalate hemihydrate BaC2O4·0.5H2O

The thermal behaviour of BaC₂O₄sd0.5H₂O and BaCO₃ in carbon dioxide and nitrogen atmospheres is investigated as part of a study about the thermal decomposition of barium trioxalatoaluminate. For this purpose thermogravimetry, differential thermal analysis, differential scanning calorimetry and high temperature X-ray diffraction were used. An infrared absorption spectrum of BaC₂O₄·0.5H₂O was scanned at room temperature.At increasing temperature, in dry nitrogen, the hydrate water of BaC₂O₄· 0.5H₂O is split off, followed by the oxalate decomposition. A part of the evolved carbon monoxide disproportionates, leaving carbon behind. At higher temperatures the latter reacts with barium carbonate, previously formed. Finally the residual solid barium carbonate decomposes into barium oxide and carbon dioxide.In dry carbon dioxide atmosphere an analogous dehydration occurs, followed by oxalate decomposition. Under these conditions the carbon formation is fully suppressed, and as a consequence no secondary reaction occurs. The barium carbonate decomposition is shifted to much higher temperatures, at a low rate in the solid phase, a strongly accelerated one at the onset of melting, and a moderated one when the melt is saturated with barium carbonate. The two phase transitions of BaCO₃ are detectable in both atmospheres mentioned.     

Preparation of silane-coated TiO2 nanoparticles in supercritical CO2

Nanometric inorganic pigments are widely used as fillers for hybrid composite materials. However, these nanometric powders are hydrophilic in nature and their surface must be functionalized before use. In this work, titanium dioxide (TiO₂) nanoparticles were coated using silane coupling agents with alkyl functionality. A supercritical carbon dioxide (scCO₂) method was used for surface silanization. Five alkylalkoxysilanes with different alkyl chain length and structure were studied: methyltrimethoxy, isobutyltriethoxy, octyltriethoxy, octyldimethylmethoxy and octadecyltrimethoxysilane. The microstructure and thermal stability of deposited monolayers were characterized using thermogravimetric analysis, ATR–IR spectroscopy, transmission electron microscopy, wettability characterization and low-temperature N₂ adsorption/desorption analysis. The use of scCO₂ as a solvent provided an effective approach to functionalize individual inorganic nanoparticles due to the enhanced diffusivity of the solution molecules in the aggregates interparticle voids. The trifunctional silanes employed here yielded surfaces with better thermal stabilities and greater hydrophobicities than the used monofunctional silane.     

Kinetics of methane combustion on Fe2O3/TiO2 catalysts

The objective of this work was to study the kinetics of methane combustion for a series of Fe₂O₃/TiO₂ catalysts. An increase in activity is observed as iron loading increases, and can be attributed to an increase of surface coverage by Fe₂O₃ species. Kinetic studies revealed that the reaction orders with respect to methane, oxygen, carbon dioxide and water are 1, 0, 0 and -1 respectively. This revised version was published online in June 2006 with corrections to the Cover Date.     

The absolute cross sections for the quenching of cadmium 5 3P1 and 5 3P0 atoms by carbon monoxide,carbon dioxide and nitric oxide

Absolute cross sections for the quenching of Cd(5 ³P₁ and Cd(5 ³P₀) by carbon monoxide, carbon dioxide and nitric oxide have been determined by a phase-shift method. It was found that carbon monoxide deactivates the Cd³P₁) atoms not only to the ground state, Cd(¹S₀), but also to the metastable state, Cd(³P₀), and that the cross section for the latter process is ten times larger than that for the former one. On the contrary, carbon dioxide quenches Cd(³P₁) atoms to the ¹S₀ state without producing Cd(³P₀) atoms. The quenching efficiency by nitric oxide was considerably large compared with those of carbon mono- and di-oxides. These quenching cross sections were compared with those of other excited metal atom states.     

Study of plasma-polymerization deposition of C2H2/CO2/H2 onto ethylene-co-propylene rubber membranes

Ethylene-co-propylene rubber (ERP) membranes were modified by use of acetylene/carbon dioxide/hydrogen (C₂H₂/CO₂/H₂) plasma-polymerization deposition. The influence of flow rate of gases, glow discharge power and deposition time on the amount of deposition was investigated. Infrared spectroscopy and scanning electron microscopy were employed to study the structure and surface morphology of the deposited EPR membrane. The water contact angle and the permeation property were examined as well. The results showed that deposition comprises oxygen-containing groups including >C=O and –OH, the hydrophilicity of EPR membrane was therefore improved. It was also found that the permeation coefficient of plasma modified EPR membrane decreased with the increase of the amount of deposition.     

Thermogravimetric study on the decomposition of hydromagnesite 4 MgCO3 · Mg(OH)2 · 4 H2O

Isothermal and non-isothermal decomposition of hydromagnesite 4 MgCO₃ · Mg(OH)₂ · 4 H₂O was studied thermogravimetrically. Decarbonation was strongly influenced by the partial pressure of carbon dioxide. Decarbonation in an argon atmosphere proceeded via an amorphous lower carbonate to MgO. Decarbonation in a carbon dioxide atmosphere was interrupted at ～460–480°C. This interruption was explained by the formation of a metastable intermediate and the subsequent crystallization of MgCO₃, both from the amorphous lower carbonate. This explanation was supported by DTA and power X-ray diffraction analysis of the quenched specimens.     

Molecular dynamic simulations of carbon nanotubes in CO2 atmosphere

This work investigates by means of molecular dynamics the filling of carbon nanotubes by carbon dioxide molecules. Nanotubes of various sizes are simulated and the resulting CO₂ density calculated. The effects of various CO₂ models are also investigated. The results show that the carbon dioxide molecules have a natural tendency to fill the nanotubes and the final CO₂ concentration inside the nanotube can be approximately 100 times (depending on diameter and CO₂ model) higher than that of the external atmosphere.     

Photocatalytic Synthesis of Hydrocarbon Oxygenates from C2H6 and CO2 over Pd-MoO3/SiO2 Catalyst

Pd-MoO3/SiO2 catalyst has been prepared using the method of incipient wetness impregnation. The photo absorbing behaviors and chemisorbing properties of the catalyst have been characterized by UV-vis spectra and TPD-MS experiments. The results indicated that metal Pd loaded on MoOe/SiO2 has a significant effect on the photo absorbing performance of MoO3/SiO2, and an obvious blue shift of the absorption edge is produced. Under UV irradiation, the chemisorption state of CO2 undergoes decomposing process to form CO at 481 K, and a two-site adsorption state of ethane can be formed at around 496 K. Photo-oxidation of ethane using carbon dioxide can mainly produce propanal, ethanol and acetaldehyde in the temperature range of 353-423 K. The presence of metal Pd improves the catalytic activity remarkably.     

The SO+2 radical-ion

From the complex overall EPR spectrum of ⁶⁰Co gamma-irradiated pure solid sulfur dioxide the spectrum of the SO⁺₂ radical-ion was selected and the following principal values for the g-tensor obtained: g₁ = 1.9620;g₂ = 2.0026;g₃ = 2.0118 (Δg = ± 0.0005).     

Reforming of CH4 with CO2and O2to produce syngas over CaO modified Ni/SiO2 catalysts in a fluidized bed reactor

Methane reforming by carbon dioxide and oxygen was investigated over 5 wt.%Ni/CaO-SiO₂ catalyst in a fluidized-bed reactor. The catalyst exhibited high activity and good stability at stoichiometric methane, carbon oxide and oxygen feed. Effects of calcium loading, space velocities, reaction temperatures and the feed gas compositions for this combined reaction were investigated. These results indicated that Ni/CaO-SiO₂ is more effective and stable. The catalyst performance, stability, structure, dispersion of nickel and carbon deposition of the modified and unmodified catalysts were investigated by a series of characterization techniques. Results showed that catalysts modified with CaO improved their stability better than the pure nickel-based catalysts. This revised version was published online in June 2006 with corrections to the Cover Date.     

Infrared Photodissociation Spectroscopic and Theoretical Study of [Co(CO2)n]+ Clusters

The mass-selected infrared photodissociation (IRPD) spectroscopy was utilized to investigate the interactions of cationic cobalt with carbon dioxide molecules. Quantum chemical calculations were performed on the [Co(CO₂)_n]⁺ clusters to identify the structures of the low-lying isomers and to assign the observed spectral features. All the [Co(CO₂)_n]⁺(n=2-6) clusters studied here show resonances near the CO₂ asymmetric stretch of free CO₂ molecule. Experimental and calculated results indicate that the CO₂ molecules are weakly bound to the Co⁺ cations in an end-on con guration via a charge-quadrupole electrostatic interaction. The present IRPD spectra of [Co(CO₂)_n]⁺ clusters have been compared to those of Ar-tagged species ([Co(CO₂)_n]⁺-Ar), which would provide insights into the tagging effect of rare gas on the weakly-bounded clusters.     

Oxygen species on NiO/Al2O3 and their reactivities

Oxygen species on fresh and treated NiO/Al₂O₃ and their activities for oxidation of ethane and ethylene were investigated using catalytic property measurements, ethane and ethylene pulse experiments and O₂–TPD–MS experiments. The results revealed that there are two kinds of active oxygen species (the more active one and the less active one) on fresh NiO/Al₂O₃ catalyst, but there is only one active oxygen species, the less active one, on treated NiO/Al₂O₃ catalyst. The more active oxygen species can convert ethane or ethylene to carbon dioxide by one step while the less active one can only convert ethane to ethylene, but cannot convert ethane and/or ethylene to carbon dioxide. The more active oxygen species can be removed from the catalyst by heating from 350 to 850 °C. The amounts of desorption oxygen on the catalysts are proportional to their selectivity to carbon dioxide.     

Partial oxidation of ethane in H2/O2 fuel cell under mild conditions

The partial oxidation of ethane to ethanol and acetaldehyde in the H₂/O₂ fuel cell under mild conditions is reported. The reaction proceeds at the carbon gasdiffusion cathode in the presence of transition metal ions (Fe²⁺, Cu²⁺) at ambient pressure and temperature 343 K.