双羟基复合金属氧化物的晶面生长选择性及晶粒尺寸控制

采用成核／晶化隔离法合成镁铝双羟基复合金属氧化物（LDH）,考察了晶化温度及晶化时间对晶体结构,晶面生长选择性及晶粒尺寸的影响规律。结果发现晶化温度相同时,随晶化时间延长,LDH的晶体结构趋于完整,晶粒尺寸增大;晶化时间相同时,随晶化温度升高,晶体结构趋于完整,晶粒尺寸显著增大,实验条件下得到的LDH,其沿a轴方向的尺寸均大于沿c轴方向的尺寸,即共沿a轴方向的生长速率比沿c轴方向的生长速度快,亦即[110]晶面的生长速率比[003]晶面的生长速率快。根据LDH晶粒尺寸随晶化时间及晶化温度的变化规律,选择合适的晶化条件,制备得到了粒径分布窄的纳米LDH。     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N_2吸附-脱附和NH_3-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比(n/n)为30~70,钠硅比(n/n)为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

低硅SAPO-34分子筛的复合模板剂法合成及其对甲醇制烯烃的催化性能

系统考察了模板剂比例和晶化条件对复合模板剂(三乙胺+四乙基氢氧化铵)法合成低硅SAPO-34分子筛的影响;评价了合成产物对甲醇制烯烃的催化性能.结果表明,190℃晶化时不易合成低硅SAPO-34分子筛,而170℃晶化、模板剂组成为2Et3N+0.3TEAOH时可合成纯相SAPO-34分子筛.较高温度晶化时,延长晶化时间,SAPO-34有向SAPO-5转晶的趋势,而较低温度晶化时则相反.与晶化3 d的分子筛样品相比,170℃晶化5 d后的分子筛样品的比表面积较大、强酸中心较多、弱酸中心较少、对甲醇制烯烃反应的催化寿命较长.     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N₂吸附-脱附和NH₃-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比（n/n）为30~70,钠硅比（n/n）为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

ZSM-5分子筛结晶度及晶粒大小的影响因素

以硅溶胶为硅源,偏铝酸钠为铝源,用晶种法制备ZSM-5分子筛.考察了物料混合方式、陈化时间、晶化时间、晶化温度、碱度和水量等对ZSM-5分子筛相对结晶度和晶粒大小的影响.用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和激光粒度分析等对所合成样品进行了表征.结果表明:在一定的高碱度条件下形成高浓度的硅铝酸盐凝胶,才能合成出晶化良好的样品,ZSM-5分子筛是按固相机理形成的;合成ZSM-5分子筛的相对结晶度和平均颗粒度均随晶化温度的升高及硅铝酸盐凝胶浓度的增加而增大,在室温陈化24 h、180℃晶化12～24 h时相对结晶度最高,平均颗粒度基本上与陈化时间无关.     

SAPO分子筛的合成及影响因素的研究进展

本文综述了SAPO分子筛的主要合成方法,包括水热合成法、气相晶化法、液相晶化法、微波合成法、变温陈化法、超声合成法、程序升温法等方法.讨论了反应物的组成、模板剂、酸碱度、介质、晶化温度、晶化时间等因素对SAPO分子筛合成的影响.最后对SAPO分子筛合成方法进行了展望.     

含有沸石结构单元体介孔材料的合成及催化性能

采用两步晶化法合成了孔壁含沸石初级结构单元的六方介孔材料,用XRD, N_2吸附－脱附,TEM,IR和NH_3TPD对样品进行了表征,考察了晶化时间、碱度、 温度和NH_4~+离子交换对样品的影响。结果表明合成的介孔材料（AlMB41）在结构 上和AlMCM-41类似,并且没有发现β沸石相的存在。样品具有较高的热稳定性。氢 型AlMB41用有强酸位,在催化异丙苯裂解和2,4－二叔丁基苯酚与叔丁醇的烷基化 反应中,其催化活性明显高于常规法合成的AlMCM-41。     

微波辅助晶化法合成MCM-22分子筛的研究

开展了微波辅助法合成MCM-22分子筛的研究, 经过29 h微波晶化得到了与传统水热法合成5 d相同的100%晶化的样品, 有效地缩短了合成时间. 通过XRD, SEM, FT-IR, ICP和²⁷Al MAS NMR技术表征, 微波辅助合成样品具有高纯度、均一形貌, Al原子有效进入骨架等特征. 对合成中的关键性条件, 如结构导向剂的含量进行了深入研究, 并给出了可能的合成机理. 此外, 通过在合成液中添加少量高介电损失物质, 进一步缩短了合成时间.     

非酸性介质中SAPO-5、SAPO-34型分子筛的合成

以三乙胺为模板剂,用水热晶化法,首次在非酸性介质中合成了SAPO-5、SAPO-34型分子筛.通过X-射线粒未衍射、电子探针微区分析、电子能谱及红外光谱进行了结构研究,确认合成样品为SAPO-5和SAPO—34型分子筛,并对它们的化学组成、热稳定性、表面酸性及吸附性能进行了研究。     

无模板剂预晶化液添加法合成ZSM-5分子筛

研究了旋转烘箱中无模板剂条件下,预晶化液添加对合成ZSM-5分子筛的影响。系统研究了预晶化液加入量对合成分子筛晶化速率及颗粒大小的影响。采用X射线衍射,扫描电镜,N2吸附-脱附,和激光粒度分布等分析方法对合成的ZSM-5分子筛样品的物化性能进行了表征。结果表明,预晶化液的添加可以明显加快分子筛的晶化速率,预晶化液添加量为33.3wt%时达到最大结晶度的合成时间由未添加时的48 h减少到24 h。添加预晶化液的母液在150℃晶化24 h时所得ZSM-5分子筛团聚体的颗粒大小随着预晶化液加入量的增大而增大,由5.5μm增大到26.3μm。团聚体颗粒的比表面积比未添加预晶化液得到的分子筛(292 m2.g-1)有了不同程度的提高,如添加量为33.3wt%时为394 m2.g-1。对预晶化液添加法合成ZSM-5分子筛团聚体颗粒的生长机理进行了讨论。     

水滑石晶体长厚比及晶粒尺寸控制方法研究

层状双金属氢氧化物（LayeredDoubleHydrox－ides，简称LDH）是一类重要的无机晶体材料，因其具有层状结构以及层板元素的可调控性和层间阴离子的可交换性，在催化、离子交换、吸附、医药犤１～８犦等方面具有广泛的用途，已受到人们越来越广泛的关注。近年来，随该类材料应用领域的不断拓展，在许多情况下要求LDH晶体具有小的粒径尺寸，以便最大限度地发挥其功能性。例如将LDH作为阻燃剂犤９犦使用，小粒径粉体可增强与聚合物基材的相容性，提高材料的阻燃、抑烟和力学性能。另一方面，因LDH具有层状结构，在复合材料中其层板能有效…     

Influence of Microwave Synthesis Parameters on the Size and Morphology of the Resulting MgAl2O4 Nanoparticles

In the present study, Nano-sized magnesium aluminate powders were successfully synthesized via microwave process based on the reaction between Mg (NO₃)₂·6H₂O and Al (NO₃)₃·9H₂O in distilled water, at various conditions. The products were characterized by X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy, photoluminescence (PL) spectroscopy, and EDAX analysis. The effects of different parameters such as reaction time and microwave power on the morphology, particle size, and PL properties of the product were studied by SEM images and the PL.     

Investigation on the thermal behaviour of Mg(NO3)2·6H2O I. The decomposition behaviour

The decomposition mechanism of Mg(NO₃)₂·6H₂O was studied by means of simultaneous TG, DTG and DTA method combined with EGA technique under conventional and quasi isothermal-quasi isobaric conditions. It has been found that Mg(NO₃)₂·6H₂O melts at 89 °C in a congruent way. The solution formed begins to boil at 147 °C. The water loss process of the salt hydrate and the decomposition process of the Mg(NO₃)₂ always overlap to some extent. Accordingly, Mg(NO₃)₂ of stoichiometric composition cannot be prepared thermally, because the compound always contains some basic salt. The last part of water departs in the vicinity of 270 °C with extreme rapidity. In contrast to expectations the compound decomposes in pure “self-generated” atmosphere at a temperature lower by about 80 °C than in the presence of air which contains a small amount of the gaseous decomposition product.     

Superparamagnetic and ferromagnetic behavior of ZnFe2O4 nanoparticles synthesized by microwave-assisted hydrothermal method

Zinc ferrite (ZnFe₂O₄) nanoparticles were successfully synthesized from Zn(NO₃)₂ · 6H₂O and Fe(NO₃)₃ · 9H₂O by microwave hydrothermal method at 150°C for 1 h. Cubic ZnFe₂O₄ with particle size below 7 nm was formed in the solution at pH ≥ 6. The crystallinity and particle size of ZnFe₂O₄ nanoparticles were increased after calcination. The effects of pH of the precursor solution and calcination on the particle size and crystallinity of the particles were studied. At room temperature the products show superparamagnetic and ferromagnetic properties, determined by their size. The formation mechanism of ZnFe₂O₄ was also discussed according to the experimental results.

     

FTIR-ATR <Emphasis Type="Italic">in situ</Emphasis> observation on the efflorescence and deliquescence processes of Mg(NO<Subscript>3</Subscript>)<Subscript>2</Subscript> aerosols

The efflorescence and deliquescence processes of Mg(NO₃)₂ aerosol particles deposited on ZnSe substrate have been investigated through in situ Fourier transform infrared-attenuated total reflection (FTIR-ATR) technique at the molecular level. At relative humidity (RH) of ∼3%, Mg(NO₃)₂ particles existed as amorphous states. The amorphous Mg(NO₃)₂ particles were transformed into crystalline Mg(NO₃)₂ · nH₂O (n ≤ 5) with slight increasing of RH. Thermodynamically stable Mg(NO₃)₂·6H₂O crystals were gradually formed on the particle surface and started to be dissolved at the saturation point (∼53% RH). At the same time, a continuous phase transition from Mg(NO₃)₂ · nH₂O (n≤5) to Mg(NO₃)₂·6H₂O occurred on the particle surface. This led the solid particles to completely deliquesce at 76% RH, which was much higher than the saturation point of 53% RH. In the efflorescence process, Mg(NO₃)₂ droplets entered into the supersaturated region due to the gradual evaporation of water. Finally, amorphous particles were formed when RH decreased below 5%. In the FTIR-ATR spectra of the supersaturated Mg(NO₃)₂ droplets, the absorbance of the symmetric stretching vibration of NO ₃ ⁻ (v ₁- NO ₃ ⁻ ) clearly became stronger. It resulted from the continuous formation of solvent share ion pairs (SIPs), and even the contact ion pairs (CIPs) between Mg²⁺ and NO ₃ ⁻ . Supported by the Trans-Century Program Foundation for the Talents by the Ministry of Education of China, the National Natural Science Foundation of China (Grant Nos. 20073004, 20473012, and 20673010), the 111 Project (B07012), and the State Key Laboratory of Physical Chemistry for Solid Surface of Xiamen University     

Redox reactions between metal nitrates and polyols with the formation of nanopowders

The reduction of metal nitrates (Cu(NO₃)₂ · 6H₂O, AgNO₃, and Ni(NO₃)₂ · 6H₂O) by polyols under hydrothermal conditions at temperatures of 150–250°C was studied. The possibility of synthesizing copper, silver, and nickel powders with average particle sizes of 10 to 150 nm depending on the concentration of initial reagents, the temperature, and the nature of a reducer was established using X-ray diffraction analysis and atomic force microscopy. Lanthanide and alkali-earth nitrates were shown to form highly dispersed powders of metal carbonates with an average particle size of ～23 nm under similar conditions.     

Synthesis of Mg–Al–Fe–NO3 layered double hydroxides via a mechano-hydrothermal route

Mg–Al–Fe–NO₃ layered double hydroxides (LDHs) with a constant Mg²⁺/(Al³⁺ + Fe³⁺) molar ratio but varying Al³⁺/Fe³⁺ molar ratios were successfully synthesized by a mechano-hydrothermal (MHT) method from Mg(OH)₂, Al(OH)₃ and Fe(NO₃)₃·9H₂O or Mg(NO₃)₂·6H₂O as starting materials. The resulting LDHs (MHT-LDHs) were characterized by XRD, TEM, SEM, FT-IR, and zeta potential, size distribution and specific surface area analyses. It was found that pre-milling played a key role in the LDH formation during subsequent hydrothermal treatment. The MHT route is advantageous in terms of low reaction temperature compared with the conventional hydrothermal method, and the target products are of high crystallinity and good dispersion compared with the conventional mechanochemical (MC) method. The MHT-LDHs had higher specific surface area and zeta potential, and lower hydrodynamic diameter than LDHs obtained by MC method (MC-LDHs). Furthermore, the removal of Cr(VI) from aqueous solutions using the LDHs was examined, showing that the MHT-LDHs are of higher removal efficiency than MC-LDHs for the heavy metal pollutant.     

Photolysis of alkaline-earth nitrates

Peroxynitrite and nitrite ions are the diamagnetic products of photolysis (with light at a wavelength of 253.7 nm) of alkaline-earth nitrates; the paramagnetic products and hydrogen peroxide were not found. The structural water in alkaline-earth nitrate crystals did not affect the qualitative composition of the photodecomposition products. The quantum yield of nitrite ions was 0.0012, 0.0038, 0.0078, and 0.0091 quanta^?1 and that of peroxynitrite ions was 0.0070, 0.0107, 0.0286, and 0.0407 quanta^?1 for Sr(NO₃)₂, Ba(NO₃)₂, Ca(NO₃)₂ · 4H₂O, and Mg(NO₃)₂ · 6H₂O, respectively.     

Design of one-pot green protocol for the synthesis of novel modified LDHs with diacids based on amino acids: morphology and thermal examinations

In this study, a simple, fast and environmentally friendly protocol has been proposed for the synthesis of layered double hydroxides (LDHs) and organomodified chiral LDHs under ultrasound irradiation as a green and fast tool for the first time. Novel chiral LDHs were synthesized in one step from the co-precipitation reaction of the Al(NO₃)₃·9H₂O, Mg(NO₃)₂·6H₂O and different bioactive N-trimellitylimido-l-amino acids in aqueous state. The obtained materials were studied by several methods such as Fourier transformed infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy and transmission electron microscopy techniques. The results of structural and morphological analyses showed the successful intercalation of chiral diacids within the interlayer of LDH clay. Thermal properties were investigated by thermogravimetry analysis. The results showed that there were four weight loss steps during the thermal decomposition. The amino acid containing N-trimellitylimido diacid created a chiral environment in the modified LDH that could be used in the chiral field.     

纳米复合氧化物CuO·SnO2的制备与结构表征

0引言由于纳米材料在热学、电学、磁学、光学等方面具有的独特性能,使其在新功能材料、催化、光电能转换等许多领域引起了人们浓厚的研究兴趣[1]。近年来,纳米催化剂对固体推进剂的燃烧性能影响研究已成为热点[2～9]。但是由于固体推进剂燃烧的特殊性,要求不仅提高燃速,而且降低压力指数,因此并非所有的纳米催化剂都是有效的。大量实践已证明[10],多种催化剂的复合使用,将可获得远远优于单一催化剂的效果。研究已发现[11],纳米复合氧化物是由多种元素复合而成,使其在结构和性能上得到互补和叠加,加上纳米粒子所具有的各种效应,从而产生独特…