Constrained photophysics of an ESIPT probe within β-cyclodextrin nanocavity and chaotrope-induced perturbation of the binding phenomenon: implication towards hydrophobic interaction mechanism between urea and the molecular probe

Geological sequestration of pure carbon dioxide (CO(2)) in coal is one of the methods to sequester CO(2). In addition, injection of CO(2) or flue gas into coal enhances coal bed methane production (ECBM). The success of this combined process depends strongly on the wetting behavior of the coal, which is function of coal rank, ash content, heterogeneity of the coal surface, pressure, temperature and composition of the gas. The wetting behavior can be evaluated from the contact angle of a gas bubble, CO(2) or flue gas, on a coal surface. In this study, contact angles of a synthetic flue gas, i.e. a 80/20 (mol%) N(2)/CO(2) mixture, and pure CO(2) on a Warndt Luisenthal (WL) coal have been determined using a modified pendant drop cell in a pressure range from atmospheric to 16 MPa and a constant temperature of 318 K. It was found that the contact angles of flue gas on WL coal were generally smaller than those of CO(2). The contact angle of CO(2) changes from water-wet to gas-wet by increasing pressure above 8.5 MPa while the one for the flue gas changes from water-wet to intermediate-wet by increasing pressure above 10 MPa.     

Rapidly Estimating Natural Gas Compressibility Factor

Natural gases containing sour components exhibit different gas compressibility factor(Z) behavior than do sweet gases.Therefore,a new accurate method should be developed to account for these differences.Several methods are available today for calculating the Z-factor from an cquation of state. However,these equations are more complex than the foregoing correlations,involving a large number of parameters,which require more complicated and longer computations.The aim of this study is to develop a simplified calculation method for a rapid estimating Z-factor for sour natural gases containing as much as 90% total acid gas.In this article,two new correlations are first presented for calculating the pseudo- critical pressure and temperature of the gas mixture as a function of the gas specific gravity.Then,a simple correlation on the basis of the standard gas compressibility factor chart is introduced for a quick estimation of sweet gases' compressibility factor as a function of reduced pressure and temperature.Finally,a new corrective term related to the mole fractions of carbon dioxide and hydrogen sulfide is developed.     

污泥水分含量对其空气气化特性的影响(英文)

利用外热式下吸固定床气化实验装置,研究了在一定的空气流量(0.05 m3/h)、气化温度(800℃)下污泥水分含量对3种不同性质污泥空气气化特性的影响。结果表明,气化气中CO2、CH4和H2含量、气化气热值以及水相生成量均随污泥水分含量的增加而增加,而CO含量和焦油生成量呈降低趋势。污泥厌氧消化使气化气中CO、CH4、H2、CmHn含量以及气化气品质降低;而污水处理工艺中的厌氧过程可改善气化气品质,其中来自A2/O工艺消化污泥的气化气品质高于普通活性污泥法消化污泥的气化气品质。随着污泥水分含量的增加,2种不同污水处理工艺产生的消化污泥气化气中CO、CO2和H2含量的差距逐渐加大,来自于同一A2/O工艺的消化与未消化污泥气化气中H2和CO2含量的差距亦逐渐加大,而消化与未消化污泥气化气中CO含量的差距则逐渐接近。     

Removal of high concentration CO2 from natural gas at elevated pressure via absorption process in packed column

Carbon dioxide (CO2) removal is an essential step in natural gas (NG) processing to provide high quality gas stream products and minimize operational difficulties. This preliminary study aims to investigate the removal of CO2 at high concentration level from the mixture of CO2-NG gas stream at elevated pressure via absorption process. This is to explore the possibility of exploring high CO2 content natural gas reserves by treatment at offshore platform. A mixed amine solvent, Stonvent-II, was used for the absorption of approximately 75 vol% CO2 in CO2-NG stream at a pressure of 10 barg. The initial solvent temperature was varied in order to study the impact of initial temperature on the absorption performance. Preliminary study at temperatures of 35°C and 45°C indicates that Stonvent-II was able to perform almost 100% removal of CO2 under both conditions. However, the CO2 absorption effect took place faster when the initial liquid temperature was lower. This is because when the initial liquid temperature is high, the temperature increase in the packing bed caused by the reaction heat is high which impacts the efficiency of absorption negatively.     

Pt/CeO2-ZrO2变换催化剂的制备、表征与性能

 用共沉淀法制备了不同Ce/Zr比的CeO2-ZrO2复合氧化物,用浸渍法制备了Pt/CeO2-ZrO2水煤气变换催化剂,并对该催化剂进行了活性评价. 结果表明,与传统的Cu基低变催化剂相比,该催化剂具有操作温度范围宽和抗氧化冲击等优点,具有应用于车载重整制氢过程的潜力. 考察了温度、空速和汽/气比等条件对催化剂活性的影响,对催化剂的制备参数和工艺参数进行了研究. 结果表明,不同Ce/Zr比的Pt/CeO2-ZrO2催化剂的活性相差很大,其中Pt/Ce0.8Zr0.2O2变换催化剂活性最高. XRD结果表明,制备的Pt/Ce0.8Zr0.2O2形成了固溶体. 通过增加单位质量催化剂表面的Pt原子数可提高催化剂的活性.     

天然铁矿石为氧载体的生物质化学链气化制合成气实验研究

在一个小型鼓泡流化床反应器上以Ar气为流化介质,对以天然铁矿石为氧载体的生物质化学链气化制合成气过程进行了研究。考察了反应温度对合成气组分、气体产率、碳转化率以及气化效率的影响,反应时间对合成气组分的影响;探讨了氧载体存在对生物质气化过程的影响。结果表明,天然铁矿石可以作为生物质化学链气化制合成气反应过程的氧载体,代替富氧空气或高温水蒸气作为生物质气化的气化剂;随着温度的升高,产物气体中CO、H₂的浓度逐渐增加,CO₂、CH₄浓度缓慢降低;随着反应时间的延长,合成气中H₂、CO、CH₄的相对浓度缓慢增加,而CO₂相对浓度逐渐降低;氧载体的存在能显著提高气体产率和碳的转化率及气化效率。扫描电镜-能谱(SEM-EDS)分析表明,当超过850 ℃时,铁矿石氧载体颗粒表面烧结现象明显,但反应前后,颗粒表面的成分及含量基本保持不变。     

镍基整体式催化剂上生物质粗燃气重整调变的特性研究

采用浸渍法制备了Ni基整体式催化剂,考察了不同条件(温度、时间、空速、水蒸气添加等)对催化剂上生物质粗燃气重整反应性能的影响。结果表明,催化剂在较低温度下(≤500 ℃)只具有CO加氢反应活性,随着反应温度的升高粗燃气重整反应逐渐进行,在800 ℃以上,CH₄和C₂转化率均高达95 %以上,CO₂转化率达到92%,但随着反应空速和水蒸气添加量的增加,CH₄和CO₂等转化率呈现缓慢降低的趋势。此外,通过改变水蒸气添加量可对合成气中H₂/CO体积比在0.85~4.00进行较好调节。结合XRD表征发现,Ni基整体式催化剂中Ni°的生成可较好地促进重整反应的进行。     

Experimental studies of biomass gasification with air

In this work,experimental studies of biomass gasification under different operating conditions were carried out in an updraft gasifier combined with a copper slag reformer.The influence of gasification temperature,equivalence ratio(ER) and copper slag catalyst addition on gas production and tar yield were investigated.The experimental results showed that the content of H2 and CO,gas yield and LHV increased,while the tar yield and the content of CO2,CH4 and C2Hx in the gas product decreased with the temperature.At 800C,with the increase of ER,the LHV,the tar yield and the content of H2,CO,CH4 and C2Hx in gas products decreased,while the gas yield and the content of CO2 increased.Copper slag was introduced into the secondary reformer for tar decomposition.The Fe3O4 phase in the fresh copper slag was reduced to FeO(Fe2+) and metallic Fe by the gas product.Fe species(FeO and metallic Fe) acted as the active sites for tar catalytic decomposition.The catalytic temperature had a significant influence on tar conversion and the composition of the gas product.Typically,the tar conversion of about 17%-54% could be achieved when the catalytic temperature was varied from 750 to 950 C.Also,the content of H2 and CO increased with the catalytic temperature,while that of CO2,CH4 and C2Hx in the gas product decreased.It was demonstrated that copper slag was a good catalyst for upgrading the gas product from biomass gasification.     

NiO／TiO_2－SiO_2催化剂上甲烷与二氧化碳转化制合成气

ＮｉＯ／ＴｉＯ_２－ＳｉＯ_２催化剂上甲烷与二氧化碳转化制合成气邓存，路勇，丁雪加（中国科学院兰州化学物理研究所ＯＳＳＯ国家重点实验室，兰州７３００００）关键词甲烷，二氧化碳，合成气，负载型Ｎｉ催化剂己有报道表明［１～４］，Ａｌ２Ｏ３担载的Ｎｉ金属催化...     

Co60 γ-radiation-induced copolymerization of ethylene and carbon monoxide

The γ-radiation-induced free-radical copolymerization of ethylene and CO has been investigated over a wide range of pressure, initial gas composition, radiation intensity, and temperature. At 20°C., concentrations of CO up to 1% retard the polymerization of ethylene. Above this concentration the rate reaches a maximum between 27.5 and 39.2% CO and then decreases. The copolymer composition increases only from 40 to 50% CO when the gas mixture is varied from 5 to 90% CO. A relatively constant reactivity ratio is obtained at 20°C., indicating that CO adds 23.6 times as fast as an ethylene monomer to an ethylene free-radical chain end. For a 50% CO gas mixture, the above value of 23.6 and the copolymerization rate decrease with increasing temperature to 200°C. The kinetic data indicate a temperature-dependent depropagation reaction. Infrared examination of copolymers indicates a polyketone structure containing ? CH₂? CH₂? and ? CO? units. The crystalline melting point increases rapidly from 111 to 242°C., as the CO concentration in the copolymer increases from 27 to 50%. Molecular weight of copolymer formed at 20°C. increased with increasing CO, indicating M?_n values >20,000. Increasing reaction temperature results in decreasing molecular weight. Onset of decomposition for a 50% CO copolymer was measured at ≈250°C.     

Efficient CO2 capture on low-cost silica gel modified by polyethyleneimine

In this work,a series of polyethyleneimine(PEI) functionalized commercial silica gel were prepared by wet impregnation method and used as CO 2 sorbent.The as-prepared sorbents were characterized by N 2 adsorption,FT-IR and SEM techniques.CO 2 capture was tested in a fixed bed reactor using a simulated flue gas containing 15.1% CO 2 in a temperature range of 25-100 C.The effects of sorption temperature and amine content on CO 2 uptake of the adsorbents were investigated.The silica gel with a 30 wt% PEI loading manifested the largest CO 2 uptake of 93.4 mg CO 2 /g adsorbent(equal to 311.3 mg CO 2 /g PEI) among the tested sorbents under the conditions of 15.1%(v/v) CO 2 in N 2 at 75 C and atmospheric pressure.Moreover,it was rather low-cost.In addition,the PEI-impregnated silica gel exhibited stable adsorption-desorption behavior during 5 consecutive test cycles.These results suggest that the PEI-impregnated silica gel is a promising and cost-effective sorbent for CO 2 capture from flue gas and other stationary sources with low CO 2 concentration.     

碱性条件下废轮胎真空热裂解研究

研究了废轮胎橡胶粉在450℃～600℃真空热解系统中热解的特性,以及温度和添加Na2CO3、NaOH对热解气液态产物的影响。实验表明,真空下废轮胎热解油收率在550℃时达到最大值,为48%左右。添加3%的NaOH能明显促进废轮胎橡胶热解,480 ℃时油产率达到最大值49.66%,随后随着温度的升高油产率呈现下降趋势。添加3%的Na2CO3对热解的促进作用不明显。热解气体产物主要有H2、CO、CH4、CO2、C2H4、C2H6以及少量其他化合物。NaOH的加入使气体产品中的H2相对体积分数明显增加,而CH4、CO、C2等的体积分数降低。通过GC和GC-MS分析热解石脑油发现,热解油品中含有11%以上的柠檬油精。     

生物质流化床氧气-水蒸气气化实验研究

在小型流化床气化装置上进行了氧气-水蒸气气化实验,考察了原料、当量比、水蒸气配比、温度、二次风和床料对气化特性的影响。结果表明,原料中C和H含量越高,气化气中H₂和CO含量越高,焦油含量越低;当量比为0.27和水蒸气配比为0.6时,H₂含量达到最大值;温度的升高可提高H₂含量,在840 ℃以上,可提高CO含量;二次风从进料口偏上且二次风比率为15%通入,气体组分变化较明显,二次风通入点位置越高,焦油含量降低幅度越大;白云石和石灰石裂解焦油和提高H₂含量的活性高于橄榄石,但同时明显提高了气体中的灰分含量。     

Separation of Bulk Carbon Dioxide-Hydrogen Mixtures by Selective Surface Flow Membrane

The separation performance of carbon dioxide-hydrogen mixtures by a nanoporous carbon membrane called selective surface flow membrane is described. The membrane selectively permeates CO2 from H2 and a H2 enriched gas is produced at the feed gas pressure. Extensive experimental data for the separation using feed gas pressures from 0.24 to 1.13 MPa and CO2 compositions from 5 to 75 (mol%) in H2 are reported. The data can be empirically correlated using a simple equation with a single adjustable-parameter. The adjustable parameter is found to be a linear function of the feed gas CO2 partial pressure.The membrane separates CO2-H2 mixture very efficiently even at a low total feed gas pressure (0.4 MPa). The membrane area required for a given separation decreases drastically with increasing feed gas pressure in the range of 0.24–0.92 MPa and then it becomes insensitive to the feed gas pressure.     

气化介质对生物质多孔床料流化床气化产气特性的影响

在自制小型常压流化床内采用多孔介质为床料,对生物质进行气化实验,分别考察了富氧气氛下温度和氧气浓度、水蒸气气氛下温度和水蒸气流量及不同种类床料对生物质产气特性的影响。结果表明,多孔床料下气化产气中可燃气体积分数随气化温度的提高而增大;随氧气浓度的增加,产气中H2的体积分数从14.52%增加到19.71%,CO的体积分数从43.41%降低到36.41%;气化剂水蒸气流量对生物质气化影响存在最佳范围;多孔床料种类不同对H₂和CO的生成以及对低碳氢化合物（C_xH_y）的催化裂解强度的促进作用也不同。     

两段式固定床富氧－水蒸气气化实验研究

以玉米芯颗粒为原料在两段式固定床气化装置上进行了气化实验,考察了当量比ER、富氧浓度OC和水蒸气配比S/B对气化温度、气化气组分、低位热值、气体产率、气化效率和碳转化率等参数的影响,并比较了两段式固定床与传统下吸式固定床的气化特性。实验结果表明,当量比为0.27时H₂的体积分数、CO的体积分数和气化效率达到最大值;增加富氧浓度能优化气化效果,但富氧浓度大于90%后,燃气质量和气化效率均提高不大;增加S/B能提高H₂的体积分数,但同时会降低CO的体积分数、气体热值、气化效率;当S/B为0.6时,氢气的体积分数达最高值33.3%,H₂/CO比为1.32;相比于传统固定床,两段式固定床气化可明显提高气化温度、氢气的体积分数、碳转化率和气化效率,降低焦油含量。     

煤炭解耦燃烧过程N迁移与转化Ⅲ:多组分气相化学反应实验

在理想平推流反应器中进行了模拟热解气对模拟烟气中NO、N₂O的还原实验研究,考察了反应温度、过剩空气系数,模拟热解气中CH₄、CO、H₂、NH₃入口浓度与模拟烟气中NO、N₂O入口浓度对NO、N₂O与总氮转化率的影响。结果表明,向NH₃添加可燃气体CO、H₂、CH₄可使NO还原窗口向低温方向移动150~200 K,该温度窗口为1 073~1 223 K;但NH₃-CO-H₂-CH₄-O₂体系对NO、N₂O的还原分解作用依赖于体系的O₂浓度,仅在富燃料情形(过剩空气系数λ为0.6)下可分别达60.6%、100%的NO、N₂O脱除率;在反应温度1 073~1 223 K及过剩空气系数λ为0.6条件下,较高的热解气CH₄、CO、H₂浓度可增加NO排放,但有利于还原N₂O;增加NH₃入口浓度可增加NO分解率。     

FID/TCD并联气相色谱法测定天然气水合物的气体组成

建立了一种氢火焰离子化检测器（FID）与热导检测器（TCD）并联检测的气相色谱分析技术。该方法一次进样,即可实现天然气水合物中C1~C6、CO2、H2S、O2+N2 16种气体成分的同时测定。实验优化了色谱柱、升温程序、柱流速、进样口温度、检测器温度、TCD参考气和尾吹气流速等仪器分析参数。在优化条件下,16种气体分子在实验浓度范围内线性关系良好,r2为0.999 03~0.999 98,方法检出限为0.000 3~0.046 mol/mol,相对标准偏差（n=6）为1.6%~5.0%。对祁连山冻土区、南海神狐海域、人工合成水合物样品的分析表明,该方法简便实用、灵敏可靠,可满足天然气水合物气体组成的分析要求。     

Methanation catalytic reactor

Storing renewable electricity in a natural gas grid is a new approach for seasonal storage. Using the existing natural gas infrastructure, a chemical energy source (methane) is stored efficiently, distributed and made available for use as required. Thus, the main step in the storage process is CO methanation. Modelling of an isothermal methanation catalytic reactor based on a kinetic scheme was carried out with Aspen plus™ software in a temperature range between 520 and 600 K and a H₂/CO molar ratio of 3, in the presence of CO₂ and steam. The model was validated by comparing simulation results with experimental ones. The maximum relative error is 10.87%. The effects of temperature, pressure and CO₂ addition in feed gas (syngas) on CO conversion and the outlet gas composition were carefully investigated.     

Energy-efficient methods for production methane from natural gas hydrates

Gas hydrates now are expected to be one of the most important future unconventional energy resources. In this paper, researches on gas hydrate exploitation in laboratory and field were reviewed and discussed from the aspects of energy efficiency. Different exploiting methods and different types of hydrate reservoir were selected to study their effects on energy efficiencies. Both laboratory studies and field tests have shown that the improved technologies can help to increase efficiency for gas hydrate exploitation. And it also showed the trend that gas hydrate exploitation started to change from permafrost to marine. Energy efficiency ratio(EER) and energy return on energy invested(EROI) were introduced as an indicator of efficiency for natural gas hydrate exploitation. An energy-efficient hydrate production process, called "Hydrate Chain Energy System(HCES)", including treatment of flue gas, replacement of CH4 with CO2, separation of CO2 from CH4, and storage and transportation of CH4 in hydrate form, was proposed for future natural gas hydrate exploitation.In the meanwhile, some problems, such as mechanism of CO2 replacement, mechanism of CO2 separation,CH4 storage and transportation are also needed to be solved for increasing the energy efficiency of gas hydrate exploitation.