Complete leaky mode coupling in dual-core photonic crystal fibre based on the coupled-mode theory

This paper theoretically investigates the dependence of leaky mode coupling between inner core fundamental mode and outer core defect mode on phase and loss matching in pure silica dual-core photonic crystal fibres with the multi-pole method. The complete mode coupling can take place when both the phase and loss matching conditions are satisfied at the avoided anti-crossing wavelength. It shows the influences of cladding structure parameters including the diameters of cladding air holes d₁, diameters of outer core holes d₂ and hole to hole pitch Λ on the characteristics of leaky modes coupling. The coupled-mode theory is used to analyse the mode transition characteristics and the complete coupling can be clearly indicated by comparing the real and imaginary parts of propagation constant of the leaky modes.     

掺杂石英系单模光纤对BSBS频移的影响

报道了对几种掺杂SiO₂石英系单模光纤的背向受激布里渊散射(BSBS)谱的实验结果,结果表明其布里渊散射斯托克斯频移主要取决于纤芯的掺杂材料和浓度,进一步分析证明了光纤掺杂后将主要通过调制杨氏模量的变化,从而导致BSBS频移量减小.     

Single mode optical fiber characterisation by the LP11 mode radiation pattern

We describe a method for determining the V-value from the far-field radiation pattern of dual mode optical fibers (this method is an extension of the work by Gambling et al. for the LP₁₁ modes). The method involves measurements of the maximum radiation angle and the angle of the first minimum. Curves are presented which can be used with dual mode fibers, determining the core diameter, the refractive index difference between core and cladding, as well as the V-value in the single mode regime for longer wavelength operation with the help of dispersion curves of the dopant materials.     

Numerical simulation of turbulent natural convection of oxide heat generating melt in a core catcher at NPP with VVER-1000

The problem statement and simulation results are presented concerning turbulent natural convection in a vertical cylindrical molten pool with internal heat generation and other parameters (inner Rayleigh number Ra _i ∼ 10¹⁶–10¹⁷) corresponding to oxide core melt in a core catcher for NPP with VVER-1000. Commercial code FLUENT 6.3 was used for CFD calculations. The results on heat transfer are approximated by power law correlations for mean Nusselt numbers vs. Rayleigh number and pool height, describing the heat transfer at upper, lateral, and total boundaries of the cylinder. The influence of volumetric heat generation and material properties is studied. Spatial distribution of wall heat transfer is analyzed for different pool heights possible in the real core catcher. Along with serial calculations with isothermal boundary conditions, the cases with heat radiation conditions are considered. The results may be used for estimations of heat transfer and melt overheating in a VVER core catcher and for coefficient identification of simplified models of integrated system severe-accident codes.     

TE-TM Mode Converter Using Optically Active Polymer

A novel TE-TM mode converter using optically active polymer: poly-1-menthylmethacrylate (PMtMA) was studied theoretically and experimentally. In a three-layered slab waveguide consisting of the PMtMA core layer on a fused quartz substrate, a low-loss TE₀-TM₀ mode conversion with an efficiency of 60 to 70% was easily obtained for the first time at a wavelength of 441.6 nm. The method to achieve a phase-matched operation of this polymer TE-TM mode converter was also discussed.     

Very large mode area optical fiber with complex ring cores

A novel kind of single-mode large-mode-area optical fiber is presented in this paper. The proposed fiber core is composed of high-index central rod and the surrounding multilayer rings. The mode characteristics are discussed considering the fiber structure parameters. The calculation results show that the proposed fiber possesses extreme large mode area of 2975 μm² with single mode operation at the wavelength of 1.08 μm. Even larger mode area of the complex ring core fiber with single mode output can be achieved by coiling the fiber, due to the significant difference of bending loss between the fundamental mode and the higher-order transverse modes. Such fibers are expected to find applications in the field of fiber lasers and amplifiers.     

Guided propagation in a step-index, multi-mode fiber: effect of index difference variation on allowable TM propagation constants

The effect of variation of core and cladding index difference, Δn=n_core−n_cladding, on allowable values for the guided mode transverse magnetic propagation constants within a step-index, multi-mode optical fiber is investigated. We use a iterative computational technique to calculate the propagation constants for modes inside and outside the core that satisfy the boundary conditions contained within the characteristic eigen-equation for the TM field components. Evidence of a strong dependence of the allowable propagation constants on changes of Δn is shown.     

Generation of short light pulses under the stimulated Brillouin scattering in fibers with an optimal feedback

The generation of short light pulses (1 ns) in single mode fibers under pumping by wide laser pulses (of a microsecond duration) due to the backward stimulated Brillouin scattering (SBS) is numerically investigated. The influence of the acoustic diffraction is taken into account. The cases of acoustic waveguide and anti-waveguide fibers are considered. For an acoustic anti-waveguide fiber, a dependence of overlap integral S on the acoustic mode number n has a sharp peak in the region of n 100. Computer simulations have demonstrated the energy conversion of the pump wave into short pulses of the signal (Stokes) wave in the case of synchronous pumping. The optimal length of the fiber should be approximately equal to the half-length of the pump pulse. The bypass time of the Stokes pulse of the optimal circuit fiber and the feedback loop must be equal to the repetition period of the pump pulse. An importance of acoustic mode structure of the fiber for the process of forming pulse train in shown. We have found that the acoustic anti-waveguide fibers with a small core (a < 3 m) can be preferable for obtaining the stable train of compressed pulses.     

Practical application of the refracted near-field technique for the measurement of optical fibre refractive index profiles

Both the theoretical basis and experimental realization of the refracted near-field technique for the direct measurement of optical fibre profiles are presented. The technique requires minimal sample preparation, no computation and is applicable to both single and multimode fibres. Both the core and the cladding are profiled. After outlining the problems associated with other techniques, the use of this method for the measurement of fibre profile, numerical aperture and geometry is discussed. Leaky mode rejection and resolution are treated in detail. A fitting procedure for determining the-value of a profile is given. The experimental apparatus is fully discussed. Results are presented to illustrate both the applicability of the technique to single and multimode fibres and also the rejection of leaky modes. The experimental sensitivity is shown sufficient to reveal an index fluctuation having a wavelength < 1m and an amplitude of < 0.0001.     

Single-modeness of short large mode area fibers: An experimental study

We experimentally investigated the limits to the endlessly single-modeness of large mode area photonic crystal fibers. We analyzed two versions of a commercial large mode area fiber with equal structural parameters but five or seven confining rings, and in both cases we found that the single mode regime becomes critical for short (<1 m) lengths. In these cases we report on the excitation of a second-order mode, whose microphotographed structure is very well reproduced by the results of numerical simulations. The multimodal behavior is further confirmed by polarization measurements. Also we found that the single-modeness is maintained in longer (>1 m) fibers. The same results were observed in large mode area fibers with different core sizes.     

真空条件下激光诱导光纤损伤特性研究

实验研究并分析了调Q Nd:YAG 脉冲激光诱导光纤损伤特性.设计了在真空条件下全石英光纤传输1064 nm 脉冲激光实验.通过将激光注入光纤端面气压降低到10—100 Pa, 光纤端面击穿阈值提高到大气环境下的185 倍.结合光纤端面损伤形貌分析可知,光纤端面损伤主要是由于激光驻波场和烧蚀共同作用的结果,光纤端面或内部大量的缺陷降低了光纤抗激光损伤的能力.在真空条件下由于光纤端面光学击穿阈值的提高,激光诱导光纤损伤特性又表现出了另外一种损伤模式——光纤初始输入段损伤.它发生在光纤输入段附 关键词： 激光损伤 光束传输 真空 石英光纤     

Mode characteristics of hollow core Bragg fiber

Analytical expression to calculate propagation constant and mode field of the hollow core Bragg fiber is derived. Numerical results are presented. It is shown that the fundamental mode of the hollow core Bragg fiber is circularly symmetric TE01 mode with no polarization degeneracy, while the higher order mode may be HE11, TM01, or TE02 etc.. This property is different from conventional optical fiber that its fundamental mode is the linearly polarized HE11 mode and is polarization degeneracy.     

Design of large mode area multicore photonic crystal fiber with a flat-top mode

A large mode area multicore photonic crystal fiber with a flattened fundamental mode is proposed in this paper. Another two kinds of single core fibers are also presented as comparison. The modal characteristics such as effective mode area and confinement loss are investigated using the finite element method. Numerical results show that a combination of flattened fundamental mode, large mode area and ultralow loss is obtained in the multicore fiber by introducing higher refractive index in the core region.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

单模光纤中弯曲损耗的测试与分析

对单模光纤中弯曲损耗随弯曲半径(1～8 mm)和波长(1530～1565 nm)变化的实验进行了测试,结果显示弯曲损耗随弯曲半径和波长呈现振荡.理论分析表明由于光纤纤芯中的基模和在包层以及涂覆层中传播的Whispering-gallery模式之间的耦合,引起了弯曲损耗的振荡,理论分析结果和实验结果基本一致.     

Simultaneous Measurement of Temperature and Refractive Index of Liquid Using Cladding-Etched Double-Core Fiber Bragg Grating

Abstract

This study proposed and demonstrated a fiber Bragg grating sensor for simultaneous detection of the temperature and refractive index of a liquid. The fiber Bragg grating is composed of three index layers: an inner core, an outer core, and a cladding. The cladding was etched for evanescent wave coupling between the outer core mode and an external liquid. The Bragg wavelength of the inner core mode is used for obtaining temperature data, while the refractive index for the liquid was determined by using the difference between the Bragg wavelength of the inner core mode and that of outer core mode.     

MICROWAVE PROPAGATION IN ROUND GUIDING STRUCTURES BASED ON DOUBLE NEGATIVE METAMATERIALS

This paper presents a theoretical study of guided propagation in a waveguide containing ordinary and negative refractive index (NRI) media. The cut-off frequency of positive/negative combined media is examined. It is calculated for each propagating mode as a solution of a characteristic equation that is solved in terms of Bessel functions, taking into account the implications of the negative refraction. In contrast to what happens in ordinary propagation, mode mixing and crossing and no cut-off modes are found for negative values of ε, μ and refractive index n. The investigation considers the range 1-80 GHz where metamaterials have been demonstrated to work with negative parameters. The results are also compared with the negative core/negative cladding case. Some applications are suggested for devices operating in the microwave frequency domain.     

Lift‐off protocols for thin films for use in EXAFS experiments

Lift‐off protocols for thin films for improved extended X‐ray absorption fine structure (EXAFS) measurements are presented. Using wet chemical etching of the substrate or the interlayer between the thin film and the substrate, stand‐alone high‐quality micrometer‐thin films are obtained. Protocols for the single‐crystalline semiconductors GeSi, InGaAs, InGaP, InP and GaAs, the amorphous semiconductors GaAs, GeSi and InP and the dielectric materials SiO₂ and Si₃N₄ are presented. The removal of the substrate and the ability to stack the thin films yield benefits for EXAFS experiments in transmission as well as in fluorescence mode. Several cases are presented where this improved sample preparation procedure results in higher‐quality EXAFS data compared with conventional sample preparation methods. This lift‐off procedure can also be advantageous for other experimental techniques (e.g. small‐angle X‐ray scattering) that benefit from removing undesired contributions from the substrate.     

Curvature effects on leaky modes in weakly guiding optical fibres

The effect of curvature on leaky modes with low losses in weakly guiding optical fibres is investigated, within a theoretical model where the cladding (outer cladding in case of multiclad fibres) is extended to infinity. Such modes already radiate rays in the cladding when the fibre is straight and two cases can be considered according to whether this ray pattern is modified near the core area in the bent fibre (strong curvature) or is not modified (weak curvature). A general loss formula is given for the case of weak curvature. The rays which are emitted in the curvature plane, towards the inner side of the bend are captured later on by the core and induce an oscillating modulation of the leakage loss, with an amplitude varying asR ^–1/2 but limited to a few per cent in practical cases (for weak curvatures). The case of strong curvatures is analysed in the special case of the LP 01 mode in fibres with a large depressed inner cladding, through a 2-D ray method. It is found that the loss oscillations are rapidly damped while the average loss is considerably increased.