Full period superconducting section physics design for injector Ⅱ of China-ADS

The China Accelerator Driven Subcritical System (China-ADS) project, which is a strategic plan and aims to design and build an ADS demonstration facility, has been proposed and launched actively in China. Injector Ⅱ as one of the parallel injectors of China-ADS, and is prompted by the Institute of Modern Physics (IMP). In this paper, a new scheme with full period lattice structure for the SC section is proposed. In the new scheme, there are sixteen periods, with one superconducting solenoid and one superconducting cavity included in each period. All of the elements are contained in four cryomodules. The dreadful influence of the mismatch caused by period structural change can be avoided, and the beam quality is favorable. In addition, this new scheme has certain advantages in reducing the project's difficulty and construction risk. The details of the design and beam dynamic simulation for the full period lattice structure are given in this paper.     

Beam steering correction of the quarter wave resonator in the HISCL

The Intensity Heavy Ion Superconducting Linear Accelerator as the injector of the High Intensity Heavy-Ion Accelerator Facility, which is a new project proposed in China has been designed. One of the design options in the low energy part is based on Quarter Wave Resonators (QWRs). However, because of the unsymmetrical geometry of the cavity, there are dipole fields near the beam hole, which may steer the beam vertically, thus leading to emittance growth and beam loss. The effect of the dipole mode field is analyzed, and a method to overcome the beam steering effect by placing QWRs with opposite orientation is proposed in this paper. The simulation results show that the beam steering effect is reduced effectively by this method, and the deviation of the beam centroid is decreased from 2.87 mm to 0.1 mm. The emittance growth is also smaller.     

A CW superconducting linac as the proton driver for a medium baseline neutrino beam in China

In a long-term planning for neutrino experiments in China, a medium baseline neutrino beam is proposed which uses a continue wave (CW) superconducting linac of 15 MW in beam power as the proton driver. The linac will be based on the technologies which are under development by the China-ADS project, namely it is also composed of a 3.2 MeV normal conducting RFQ and five different types of superconducting cavities. However, the design philosophy is quite different from the China-ADS linac because of the much weaker requirement on reliability here. The nominal design energy and current are 1.5 GeV and 10 mA, respectively. The general considerations and preliminary results on the physics design will be presented here. In addition, the alternative designs such as 2.0 GeV and 2.5 GeV, which may be required by the general design, can be easily extended from the nominal one.     

A new compact structure for a high intensity low-energy heavy-ion accelerator

A new compact accelerating structure named Hybrid RFQ is proposed to accelerate a high-intensity low-energy heavy ion beam in HISCL （High Intensive heavy ion SuperConducting Linear accelerator）, which is an injector of HIAF （Heavy Ion Advanced Research Facility）. It is combined by an alternative series of acceleration gaps and RFQ sections. The proposed structure has a high accelerating ability compared with a conventional RFQ and is more compact than traditional DTLs. A Hybrid RFQ is designed to accelerate 238U34＋ from 0.38 MeV/u to 1.33 MeV/u. The operation frequency is described to be 81.25 MHz at CW （continuous wave） mode. The design beam current is 1.0 mA. The results of beam dynamics and RF simulation of the Hybrid RFQ show that the structure has a good performance at the energy range for ion acceleration. The emittance growth is less than 5% in both directions and the RF power is less than 150 kW. In this paper, the results of beam dynamics and RF simulation of the Hybrid RFQ are presented.     

Physics design of CYCAIE-100

The design and construction of Beijing Radioactive Ion-beam Facility (BRIF) was started at China Institute of Atomic Energy -CIAE) in 2004. In this project, a 100 MeV high intensity cyclotron, CYCIAE100, is selected as a driving accelerator for radioactive ion beam production. It will provide a proton beam of 75—100 MeV with an intensity of 200—500 μA. The scheme adopted in this design, i.e., stripping the accelerated H-, makes the structure more compact and construction cost much lower. At present, the design for each system has been accomplished. This paper depicts the basic physics design of the machine, including its major structure and parameters, beam dynamics and each relevant system, e.g. basic structure of the main magnet, numerical simulation of the RF resonant cavity, axial injection system, central region, and study on crucial physics problems concerning the extraction and beam lines. The major problems encountered during the design of CYCIAE-100 are also summarized in this paper.     

Design study on very low Beta spoke cavity for China-ADS

Very low Beta superconducting spoke cavity is one of the key challenges for the China-ADS project. In this paper, a new structure of 3βλ/2 spoke cavity is first studied in detail. Its RF and mechanical properties are simulated using CST-MWS and ANSYS, and compared with the traditional βλ/2 spoke structure.     

The magnet design for the HLS storage ring upgrade project

In order to improve the performance of the Hefei Light Source (HLS), in particular to get higher brilliance synchrotron radiation and increase the number of straight section insertion devices, an upgrade project called HLSII will be launched soon. The storage ring lattice, which has a double bend achromatic structure with four periods, comprises eight dipoles, 32 quadrupoles and 32 combined function sextupoles. The design and analysis of the magnets are shown in this paper, along with the optimization of the multipurpose combined function magnet, which consists of three magnets: skew quadrupole, horizontal dipole and vertical dipole, with the main sextupole magnet. This type of magnet is the first one that has been designed and used in China. The mechanical design and fabrication procedures for the magnets are also presented.     

Physical design of a 10 MeV LINAC for polymer radiation processing

In China, polymer radiation processing has become one of the most important processing industries. The radiation processing source may be an electron beam accelerator or a radioactive source. Physical design of an electron beam facility applied for radiation crosslinking is introduced in this paper because of it’s much higher dose rate and efficiency. Main part of this facility is a 10 MeV travelling wave electron linac with constant impedance accelerating structure. A start to end simulation concerning the linac is reported in this paper. The codes Opera-3d, Poisson-superfish and Parmela are used to describe electromagnetic elements of the accelerator and track particle distribution from the cathode to the end of the linac. After beam dynamic optimization, wave phase velocities in the structure have been chosen to be 0.56, 0.9 and 0.999 respectively. Physical parameters about the main elements such as DC electron gun, iris-loaded periodic structure, solenoids, etc, are presented. Simulation results proves that it can satisfy the industrial requirement. The linac is under construction. Some components have been finished. Measurements proved that they are in a good agreement with the design values.     

Updating the CSNS injector linac to 250 MeV with superconducting double-spoke cavities

In order to update the beam power from 100 k W to 500 k W in the China Spallation neutron source(CSNS) Phase, one of the important measures is to replace the 80 m long beam transport line between the present80 Me V linac injector and the rapid cycling synchrotron(RCS) to another kind of acceleration structure. In this paper, we proposed a scheme based on 324 MHz double-spoke superconducting cavities. Unlike the superconducting elliptical cavity and normal conducting coupled cavity linac(CCL) structure, the double-spoke cavity belongs to the TE mode structure and has a smaller transverse dimension compared with that of the TH mode one. It can work at base frequency as the drift tube Linac(DTL) section, so that the cost and complexity of the RF system will be much decreased, and the behaviors of the beam dynamics are also improved significantly because of the low charge density and larger longitudinal acceptance. Furthermore, because of the relatively longer interactive length between the charged particle and the electromagnetic field per cell, it needs relatively less cell numbers and it has larger velocity acceptance compared with the double frequency TH structures. The superconducting section consists of 14 periods, each of which includes 3 superconducting cavities encapsulated in one cryomodule and a doublet in room temperate. The general considerations on cavity and beam dynamics design are discussed and the main results are presented.     

Scheme of negative acoustic radiation force based on a multiple-layered spherical structure

Acoustic radiation force(ARF), as an important particle manipulation method, has been extensively studied in recent years. With the introduction of the concept of “acoustic tweezers”, negative acoustic radiation has become a research hotspot. In this paper, a scheme of realizing negative ARF based on the multiple-layered spherical structure design is proposed. The specific structure and design idea are presented. Detailed theoretical calculation analysis is carried out.Numerical simulations have...     

Preliminary design and simulation of a 162.5 MHz high-intensity proton RFQ for an accelerator driven system

A new procedure for the design and simulation of a Radio Frequency Quadrupole (RFQ) accelerator has been developed at the Argonne National Laboratory. This procedure is integrated with the beam dynamics design code DESRFQ and the simulation code TRACK, which are based on three-dimensional field calculations and the particle-in-cell mode beam dynamics simulations. This procedure has been applied to the development of a 162.5 MHz CW RFQ which is capable of delivering a 10 mA proton beam for the Accelerator Driven System (ADS) of the CAS. The simulation results show that this RFQ structure is characterized by the stable values of the beam acceleration efficiency for both the zero current beam and space charge dominated beam. For an average beam current of 10 mA, there is no transverse rms emittance growth, the longitudinal rms emittance at the exit of RFQ is low enough and there is no halo formation. The beam accelerated in the RFQ could be accepted easily and smoothly by the following super-conducting linear accelerator.     

Development of x-ray scintillator functioning also as an analyser grating used in grating-based x-ray differential phase contrast imaging

In order to push the grating-based phase contrast imaging system to be used in hospital and laboratories,this paper designs and develops a novel structure of x-ray scintillator functioning also as an analyser grating,which has been proposed for grating-based x-ray differential phase contrast imaging. According to this design,the scintillator should have a periodical structure in one dimension with the pitch equaling the period of self-image of the phase grating at the Talbot distance,where one half of the pitch is pixellated and is made of x-ray sensitive fluorescent material,such as CsI(Tl),and the remaining part of the pitch is made of x-ray insensitive material,such as silicon. To realize the design,a deep pore array with a high aspect ratio and specially designed grating pattern are successfully manufactured on 5 inch silicon wafer by the photo-assisted electrochemical etching method. The related other problems,such as oxidation-caused geometrical distortion,the filling of CsI(Tl) into deep pores and the removal of inside bubbles,have been overcome. Its pixel size,depth and grating pitch are 3 μm×7.5 μm,150 μm and 3 μm,respectively. The microstructure of the scintillator has been examined microscopically and macroscopically by scanning electron microscope and x-ray resolution chart testing,respectively. The preliminary measurements have shown that the proposed scintillator,also functioning as an analyser grating,has been successfully designed and developed.     

Beam dynamics study of RFQ for CADS with a 3D space-charge-effect

The ADS (accelerator driven subcritical system) project was proposed by the Chinese Academy of Sciences. The initial proton beams delivered from an electron cyclotron resonance ion source can be effectively accelerated by 162.5 MHz 4.2 m long room temperature radio-frequency-quadrupoles (RFQ) operating in CW mode. To test the feasibility of this physical design, a new Fortran code for RFQ beam dynamics study, which is space charge dominated, was developed. This program is based on Particle-In-Cell (PIC) technique in the time domain. Using the RFQ structure designed for the CADS project, the beam dynamics behavior is performed. The well-known simulation code TRACK is used for benchmarks. The results given by these two codes show good agreements. Numerical techniques as well as the results of beam dynamics studies are presented in this paper.     

Electron gun system for NSC KIPT linac

In the NSC KIPT linac, a neutron source based on a subcritical assembly driven by a 100 MeV/100 kW electron linear accelerator is under design and development. The linear accelerator needs a new high current electron gun. In this paper, the physical design, mechanical fabrication and beam test of this new electron gun are described.The emission current is designed to be higher than 2 A for the pulse width of 3 μs with repetition rate of 50 Hz.The gun will operate with a DC high voltage power supply that can provide a high voltage up to 150 kV. Computer simulations and optimizations have been carried out in the design stage, including the gun geometry and beam transport line. The test results of high voltage conditioning and beam test are presented. The operation status of the electron gun system is also included. The basic test results show that the design, manufacture, and operation of the new electron system are basically successful.     

End-to-end simulation of the C-ADS Injector Ⅱ with a 3-D field map

The InjectorⅡ, one of the two parallel injectors of the high-current superconducting proton driver linac for the China Accelerator-Driven System (C-ADS) project, is being designed and constructed by the Institute of Modern Physics. At present, the design work for the injector is almost finished. End-to-end simulation has been carried out using the TRACK multiparticle simulation code to check the match between each acceleration section and the performance of the injector as a whole. Moreover, multiparticle simulations with all kinds of errors and misalignments have been performed to define the requirements of each device. The simulation results indicate that the lattice design is robust. In this paper, the results of end-to-end simulation and error simulation with a 3-D field map are presented.     

Study of shielding design for SANS at CSNS

The small angle neutron scattering (SANS) instrument is presently being constructed at Chinese Spallation Neutron Source (CSNS) in China, and the biological shielding design is needed to prevent the instrument from causing excessive dose rates in accessible locations. In this paper, the study of shielding design for SANS that relies on Monte Carlo simulation is introduced. Beam line shielding calculations are performed considering both scenarios of closed versus open T0 chopper. The basic design scheme of the beam stop is discussed. The size of the T0 chopper rotor is also estimated.     

A new Rosslor hyperchaotic system and its realization with systematic circuit parameter design

Based on two modified Rosslor hyperchaotic systems, which are derived from the chaotic Rosslor system by introducing a state feedback controller, this paper proposes a new switched Rosslor hyperchaotic system. The switched system contains two different hyperchaotic systems and can change its behaviour continuously from one to another via a switching function. On the other hand, it presents a systematic method for designing the circuit of realizing the proposed hyperchaotic system. In this design, circuit state equations are written in normalized dimensionless form by rescaling the time variable. Furthermore, an analogous circuit is designed by using the proposed method and built for verifying the new hyperchaos and the design method. Experimental results show a good agreement between numerical simulations and experimental results.     

Design of proton beam optics to realize beam distribution transformation in C-ADS HTBT

The linac to the transmuter beam transport line (LTBT) connecting the end of the linac to the spallation target is a critical sub-system in the accelerator driven system (ADS). It has the function of transporting the accel-erated high power proton beam to the target with a beam footprint satisfying the special requirements of the minor actinide (MA) transmuter. In this paper, a preliminary conceptual design of the hurling magnet to transmuter beam transport section (HTBT), as a part of the LTBT, for the China ADS (C-ADS) system is proposed and developed. In this design, a novel hurling magnet with a two dimensional amplitude modulation (AM) of 1 kHz and scanning of more than 10 kHz at 360 in transverse directions is used to realize a 300 mm diameter uniform distribution of beam on target. The preliminary beam optics design of C-ADS HTBT optimized to minimize the beam loss on the vacuum chamber and the radiation damage caused by back-scattering neutrons will be reported.     

Low emittance lattice optimization using a multi-objective evolutionary algorithm

A low emittance lattice design and optimization procedure are systematically studied with a non-dominated sorting-based multi-objective evolutionary algorithm which not only globally searches the low emittance lattice, but also optimizes some beam quantities such as betatron tunes, momentum compaction factor and dispersion function simultaneously. In this paper the detailed algorithm and lattice design procedure are presented. The Hefei light source upgrade project storage ring lattice, with fixed magnet layout, is designed to illustrate this optimization procedure.     

Mutator for transferring a memristor emulator into meminductive and memcapacitive circuits

In this paper, a concise but effective interface circuit for transforming a memristor into meminductive and memcapacitive systems is designed. This newly proposed interface circuit, constructed by only two current conveyors, is equipped with three available ports, which can provide six connecting combinations in terms of one resistor, one capacitor, and one memristor. For the sake of confirming the design effectiveness, theoretical and simulation discussions are hence introduced and all the experimental waveforms provide conclusive evidence to validate the correctness of these new mutators. The most attractive features of this new interface circuit are the floating terminals and convenient practical implementation.