不同磷含量对NiMoP/Al_2O_3加氢处理催化剂的影响

采用NiMoP浸渍液浸渍载体γ-Al2O3制备了不同磷含量的NiMoP/Al2O3加氢处理催化剂.为了研究磷对该系列催化剂活性相结构的影响,用二苯并噻吩(DBT)和喹啉为模型化合物,考察了催化剂的加氢脱硫(HDS)和加氢脱氮(HDN)性能.结果表明,添加适当的磷能够提高催化剂的HDS和HDN活性,但是高含量的磷能显著的降低催化剂的催化性能.通过对催化剂进行XRD和HRTEM表征发现,添加磷能够增加MoS2的堆积层数以及Ⅱ型"Ni-Mo-S"相的相对含量,这是因为在制备过程中添加磷降低了活性组分与载体之间的相互作用.     

焙烧温度对二甲醚水蒸气重整制氢 Cu/ZnO/Al2O3/Cr2O3+H-ZSM-5双功能催化剂性能的影响

采用共沉淀耦合机械混合法制备了Cu/ZnO/Al₂O₃/Cr₂O₃+H-ZSM-5双功能催化剂,并用于二甲醚水蒸气重整制氢反应,结合热重、傅里叶红外光谱、XRD、BET、H₂-TPR表征,考察了焙烧温度对Cu/ZnO/Al₂O₃/Cr₂O₃催化剂物理化学性质及双功能催化剂催化性能的影响。研究结果表明,400℃焙烧时,析出CuO粒子的同时伴有尖晶石相,进而在反应过程中对金属铜粒子起到良好的隔离作用。而焙烧温度较低时,催化剂分解不完全,催化剂活性位较少。焙烧温度大于500℃时,CuO粒子发生二次团聚,同时尖晶石相大量生成,造成催化剂活性位减少,活性较低。合适的焙烧温度为400℃,此时二甲醚转化率为92.9%,氢气收率可达到76.5%,具有较好的反应效果。     

丙烯对丙烷脱氢催化剂PtSnK/Al2O3炭沉积行为的影响

以含有不同比例丙烯的丙烷为原料进行丙烷脱氢反应,重点考察富丙烯条件下Pt基催化剂上的碳沉积行为。研究结果表明,原料中丙烯的存在加快了催化剂的积炭速率,缩短了积炭在载体上达到积炭平衡的时间,促进了活性相表面积炭的形成及积炭石墨化;同时原料中富含丙烯,使不饱和脂肪族化合物的生成量增加,从而促进了芳香性的碳、石墨化的碳的生成,但催化剂结构未遭到破坏。在丙烷脱氢过程中,当丙烯含量增加到1.5%时,出现活性相表面上的积炭“峰Ⅰ”,而“峰Ⅱ”向高温区移动。当烯烃含量增加3.0%时,峰Ⅰ和峰Ⅱ融合在一起,整个峰的面积明显增加,积炭量超过10.26%时,催化剂积炭石墨化程度越来越高。丙烯含量增加,加速了载体的容碳能力迅速饱和过程,同样的反应时间下,积炭量增加。     

制备方法对Fe2O3/Al2O3-ZrO2在乙苯脱氢反应中催化性能的影响

为提高含铁催化剂的脱氢活性,采用浸渍法和一步沉淀法制备了Fe、Al和Zr含量相同的F4AZ10-imp和F4AZ10-pre催化剂,在550 ℃考察了其在乙苯CO₂氧化脱氢制苯乙烯反应过程中的催化性能,并结合XRD、N₂-吸附、NH₃-TPD、CO₂-TPD和H₂-TPR等表征手段对催化剂进行了分析。结果表明,与浸渍法相比,一步沉淀法制备的催化剂更有利于活性组分Fe₂O₃在催化剂表面的分散及反应物CO₂的转化。     

TiO2对Ni/Al2O3催化剂CO甲烷化性能的影响

采用溶胶凝胶法制备了一系列不同TiO₂含量的TiO₂-Al₂O₃复合载体,并通过浸渍法制备了NiO/TiO₂-Al₂O₃催化剂。分别考察了不同TiO₂含量的NiO/TiO₂-Al₂O₃催化剂及反应温度对CO甲烷化催化性能的影响。实验结果表明,当复合载体中TiO₂质量分数为30%,反应温度为350～450 ℃时,催化剂催化活性较高。利用N₂吸附-脱附(BET)、X射线衍射(XRD)及H₂程序升温还原(H₂-TPR)等手段对催化剂物化性能进行了表征。结果表明,加入适量的TiO₂能抑制镍铝尖晶石NiAl₂O₄物种的生成,改善NiO的表面分散性能,避免大晶粒NiO的形成,也改善了催化剂的还原性能,从而提高催化剂的CO甲烷化活性。     

浆态床中Cu/ZnO/Al2O3/ZrO2+γ-Al2O3双功能催化剂一步法合成二甲醚

采用共沉淀法,制备了纤维状CD501甲醇合成催化剂,采用SEM、TEM、XRD和BET等手段对催化剂进行了表征;并将其进一步和γ-Al₂O₃进行混合,获得了Cu/ZnO/Al₂O₃/ZrO₂+γ-Al₂O₃双功能催化剂,考察了其在浆态床中一步法合成二甲醚过程的催化特性。结果表明,相比商业催化剂(COM)和LP201催化剂,新型的CD501催化剂具有更大的比表面积和Cu/Zn分散性。对于浆态床中一步法合成二甲醚过程,采用CD501与γ-Al₂O₃双功能催化剂,相比采用COM或LP201与γ-Al₂O₃双功能催化剂,CO转化率提高了一倍,且经过270h测试,CO转化率从61%降至57%,二甲醚时空产率从0.54g/(g·h)降至0.48g/(g·h),稳定性显著优于COM催化剂。当反应温度为250℃,压力为4.0MPa,空速为3000mL/(g·h),氢碳比为1.0时,该催化剂应用在浆态床一步法合成二甲醚时,CO转化率为61%,DME时空产率达到0.54g/(g·h)。     

模板-聚合法Pd/Al2O3催化剂制备及其蒽醌加氢性能研究

以丙烯酸铵为模板剂,由油柱成型法制备了系列球形Al2O3载体,采用XRD、BET等分析测试手段对其晶体结构、比表面积、孔容和孔径分布进行了表征,结果表明,600℃焙烧的球形γ-Al2O3载体具有介孔结构,并且比表面较不使用模板剂的样品有大幅度增加。焙烧温度升至960℃得到δ-Al2O3,介孔结构消失,但由于结构记忆效应,载体的大表面特性得以保持。以δ-Al2O3为载体制备Pd/Al2O3催化剂,采用氢-氧滴定(HOT)方法测定发现,比表面的增加显著提高了Pd金属的分散度,从而大幅度提高了催化剂的蒽醌加氢活性,氢化效率最高可达10.5 g.L-1。     

沉淀方式对微波辐射老化制备CuO/ZnO/Al2O3催化剂性能的影响

采用微波辐射老化沉淀母液的方法,着重考察了沉淀方式对制备的CuO/ZnO/Al₂O₃催化剂及其前驱体的结构和催化性能的影响。实验结果表明,沉淀方式对催化剂的活性和稳定性影响较大,其活性顺序为分步沉淀法二＞并流共沉淀法＞分步沉淀法一＞反加法＞正加法。通过XRD、DTG、H₂-TPR等表征分析表明,先并流沉淀Al(NO₃)₃溶液和Na₂CO₃溶液,再并流沉淀Cu(NO₃)₂-Zn(NO₃)₂混合溶液与剩下的Na₂CO₃溶液,然后微波辐射老化所制备前驱体中含有更多的绿铜锌矿 (Cu,Zn)₅ (CO₃)₂(OH)₆物相,焙烧后形成的CuO-ZnO协同作用强,且CuO分散性好,H₂还原温度较低,催化活性和稳定性也较高。     

Fe2O3晶型对Fe基催化剂的CO2加氢性能影响

以共沉淀法制备FeAl母体,采用浸渍法添加Zn、K和Cu助剂制成催化剂,利用低温N2物理吸附、XRD、H2-TPR等手段对FeAl母体和催化剂进行表征,并用固定床反应器考察它们的CO₂加氢反应性能。XRD结果表明,加入Al助剂、并采用无水乙醇洗涤沉淀能促进酌-Fe₂O₃晶相生成,其中,Al₂O₃/Fe₂O₃质量比为10%的母体具有最强的酌-Fe₂O₃衍射峰;加入Al使得母体中的a-Fe₂O₃晶粒粒径变小,引起比表面积明显增大;浸渍助剂过程没有改变上述两种效应。母体比表面积增大提高了助剂Cu的分散度,促进了催化剂还原,但酌-Fe₂O₃晶相的生成才是催化剂的CO₂加氢反应活性被提高的主要原因。     

纳米膜组装介孔Al2O3：合成及Pt/Al2O3的硝基苯催化加氢性能

以"乙酸乙酯(EA)-偏铝酸钠-水"体系在室温下合成了纳米膜组装介孔Al2O3。研究发现:合成反应时间、静置前搅拌时间、NaAlO2用量、EA用量及反应温度等对合成产物的形貌有影响;另外,与用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂相比,纳米膜组装介孔Al2O3制备的Pt/Al2O3催化剂含有部分易被还原的PtOx物种。在硝基苯催化加氢反应中,用合成Al2O3为载体制备的Pt/Al2O3催化剂,比用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂具有更好的催化活性。     

Methane steam reforming over rhodium promoted Ni/Al2O3 catalysts

The effect of Rh addition upon catalyst characteristics and performance in methane steam reforming was investigated using Rh-promoted Ni/Al₂O₃ catalysts. The number of reduced metal atoms exposed on the surface increased for the Rh-promoted catalysts. Rh-promoted catalysts showed an increase in CH₄ reforming activity; however, constant turnover frequencies for promoted and unpromoted catalysts suggest that the increase in the number of metal surface atoms caused the activity enhancement. Rh also facilitated reduction of Ni/Al₂O₃.     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

Hydrogenation of nitrate in water over bimetallic Pd-Ag/Al2O3 catalysts

Hydrogenation of nitrate (NO₃ ⁻) in water was studied with 0.8 ×10⁻³–3.2 ×10⁻³ mol/dm³ of reactant in the temperature range of 293–313 K over palladium promoted Ag catalysts. Pd-Ag catalysts with a low ratio of Ag/Pd were characterized by high efficiency in the reduction of nitrates. The degradation of nitrates followed approximately first order decay and the estimated apparent activation energy was about 4 kJ/mol.     

Ring opening of methylcyclopentane over Al2O3 and SiO2 supported Rh catalysts

Hydrogenolytic ring opening of methylcyclopentane (MCP) was investigated on Rh/Al₂O₃ and Rh/SiO₂ catalysts, prepared by the incipient wetness method. Strong dependence can be seen in the yield and distribution of ring opening products as a function of temperature and hydrogen pressure. They depended also on the support used. The ring opening reaction required high hydrogen coverage, and was not random (hindered in the vicinity of the methyl group), thus, mainly 2-methylpentane (2MP) and 3-methylpentane (3MP) were formed. The fragments consisted of C₁–C₅ alkanes, with methane andi-pentane as main fragments. This means the possibility of breaking two C−C bonds during one sojourn of the reactant on the catalyst, both taking place far from the substituent. The loose positive correlation between the ratios ofi-pentane/n-pentane and 3MP/n-hexane seems to support this conclusion. Dedicated to Professor Pál Tétényi on the occasion of his 70th birthday     

Preparation, characterization and application of KNH2/Al2O3 and KF/Al2O3 as strong solid bases

This review describes the preparation, characterization and application of KNH₂ loaded on alumina and KF loaded on alumina. These strong solid bases catalyze a variety of organic reactions in a very selective manner. The reactions include isomerizations of alkenes and alkynes, dimerization of alkynes, Tishchenko reaction, and the reaction of silanes to form of Si–C, Si–N and Si–O bonds.     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

The Al2O3-Fe2O3 Mixed Oxidic System, I. Preparation and Characterization

A series of Al₂O₃-Fe₂O₃ mixed oxidic solids with composition ranging from 0 to 100% of Fe₂O₃ were prepared and examined for structural characteristics. XRD diagrams showed the presence of α-Al₂O₃ and hematite phases. The analysis of M?ssbauer spectra revealed the existence of two iron containing phases. The specific surface area of the mixture decreases by the addition of iron and depends on the crystal phases of the mixture. This revised version was published online in June 2006 with corrections to the Cover Date.     

Activity of bifunctional Pt-Dy/Al2O3 catalysts in hydrocarbon reactions

The conversions ofn-hexane and methylcyclopentane on Pt–Dy/Al₂O₃ containing different amounts of Dy have been investigated in a pulsed microcatalytic reactor. The poisoning effect of thiophene on the activity of Pt–Dy/Al₂O₃ for n-hexane conversion has been studied. The influence of Dy over Pt–Dy/Al₂O₃ is also discussed.