660nm单一波长Nd∶YAG陶瓷激光器

针对陶瓷晶体1319nm的谱线设计了适合的谐振腔腔镜膜系参量,采用激光二极管列阵侧向抽运掺杂1.1at%、Φ3×50mm的Nd∶YAG陶瓷,利用色散棱镜及KTP晶体Ⅱ类匹配腔内倍频,研制了一台660nm单一波长输出的高重频Nd∶YAG陶瓷红光激光器.根据陶瓷晶体的热透镜焦距设计了谐振腔的各个参量,在重复频率为1000Hz、单脉冲抽运能量约144mJ时,获得了3.9mJ的660nm脉冲激光输出,总的光-光转换效率为2.71%.为进一步研究大功率、高效率的陶瓷红光激光器奠定了基础.     

大功率准连续Nd:YAG陶瓷激光器研究

采用侧面环绕均匀排布的紧凑型抽运结构,实现了激光二极管阵列侧向抽运Nd∶YAG陶瓷激光器高效率激光输出。理论计算得到谐振腔输出镜的最佳输出耦合透射率为22.2%,并在输出耦合镜透射率为22%的条件下,用掺杂原子数分数为1%,尺寸为5mm×75mm的Nd∶YAG陶瓷棒,获得了平均功率大于230W的准连续1064nm激光输出,其光光效率和斜率效率分别高达52.4%和61%。并测得输出激光脉冲宽度为160μs,光谱线宽略小于0.8nm,光束发散角为16mrad。实验结果显示,Nd∶YAG陶瓷激光器输出功率Nd∶YAG单晶激光器相当。     

国产掺Nd3+透明薄片陶瓷的光学性能研究

研究了国产透明陶瓷Nd∶YAG和Nd∶YSAG的光学和激光性能.介绍了透明陶瓷Nd∶YAG和Nd∶YSAG的制作方法及其光谱性能,报道了相应的激光实验结果.对于Nd∶YAG薄片激光器,得到了中心波长1 064.2 nm,半高全宽为0.89 nm的激光输出,泵浦阈值功率0.267 W,最大激光输出功率0.319 W.对于Nd∶YSAG薄片激光器,由于荧光寿命比较长,可实现高掺杂,输出激光的中心波长为1 063.8 nm,半高全宽为1.6 nm,最大激光输出功率为0.356 W,斜率效率达23.2％,结果证明国产Nd∶YSAG陶瓷适用于短脉冲薄片激光器.     

二极管泵浦1064nm单频Nd∶YAG激光器输出功率稳定控制系统设计

介绍了激光二极管(LD)端面泵浦1 064 nm单频Nd∶YAG激光器的工作原理和结构特点,分析了影响这种固体激光器输出功率稳定性的主要因素,设计并实验研究了一种用于稳定该激光器输出功率的控制方案。该方案在严格控制LD和Nd∶YAG晶体工作温度的条件下,当单频Nd∶YAG激光器的输出功率波动时,根据LD输出功率与其注入电流成正比这一变化规律,利用获得的功率误差信号反馈控制LD的注入电流,即可稳定单频Nd∶YAG激光器的输出功率。实验结果表明:当LD泵浦1 064 nm单频Nd∶YAG激光器的输出功率约为11.5 mW时,采用所设计的控制系统,可使激光输出功率稳定性在130 min内优于1.3%。     

915 nm单频Nd∶YAG晶体衍生光纤激光器

报道了一种基于Nd∶YAG晶体衍生光纤(NYDF)的915 nm单频光纤激光器.使用掺杂原子数分数为2.5％的Nd∶ YAG晶体作为纤芯材料,高纯度石英管作为包层材料,利用熔芯法制备Nd∶ YAG晶体衍生光纤,其传输损耗为8 dB/m,在915 nm处其增益系数为1.16 dB/cm.基于Nd∶YAG晶体衍生光纤,实现了一个稳定的915 nm单频光纤激光器,信噪比大于50 dB.实验结果表明Nd∶ YAG晶体衍生光纤有潜力应用于890～920 nm单频激光器.     

新型全固态激光器作用过程中的激光参数分析

对影响LD泵浦的Nd∶GdVO4,Nd∶YVO4和Nd∶YAG激光器输出特性的增益介质长度、腔内损耗、输出镜透过率、泵浦光和振荡光的光斑大小进行了分析和数值模拟。当腔内固有损耗为2%,输出镜透过率为10%时,Nd∶Gd-VO4,Nd∶YVO4和Nd∶YAG晶体的振荡阈值分别为1.77W、0.55W和3.34W。在25W泵浦功率下,利用1mm长的Nd∶GdVO4,Nd∶YVO4和Nd∶YAG晶体可分别得到13.17W,13.26W和8.43W的输出功率,相应的输出镜最佳透过率分别为24%,44%和16%。     

被动调Q自拉曼Nd∶GdVO4激光器

对激光二极管(LD)抽运的自拉曼Nd∶GdVO4被动调Q激光器进行了详细的理论和实验研究。实验中采用Nd∶GdVO4晶体同时作为激光介质和拉曼晶体,分别用了两块不同初始透射率的Cr4 ∶YAG晶体,得到并比较了采用不同初始透射率的Cr4 ∶YAG晶体时被动调Q自拉曼激光器的性能。测量了平均输出功率、脉冲宽度和脉冲重复率随抽运功率的变化关系。当Cr4 ∶YAG的初始透射率为0.91,输入功率是5.7 W时,得到的拉曼光的最高功率为244.6 mW,相应的转换效率为4.3%。通过数值求解基频光和拉曼光空间分布的速率方程并应用到被动调Q自拉曼Nd∶GdVO4激光器。获得的理论结果与实验结果大致相符。     

用于准相位匹配的LD泵浦Nd∶YAG 946nm连续激光光源

本文为泵浦质子交换准相位匹配波导器 Li Nb O3 提供了激光光源 ,用 80 8nm半导体激光器泵浦 Nd∶ YAG晶体 ,在室温下获得 946 nm激光连续输出大于 1 2 0 m W,斜率效率9.8% ,并且在国内首次实现了 LD泵浦 Nd∶YAG/ KNb O3 4 73 nm蓝色激光器的连续运转 ,报道了初步的实验结果并对此进行了详细的分析 ,提出了改进方案 .     

采用解析法对Nd:YAG单晶光纤的温度场研究

采用解析法对Nd:YAG单晶光纤激光器热效应相关的光纤温度场分布进行研究。建立了Nd:YAG单晶光纤热模型,在单晶光纤所满足的边界条件下通过解析求解热传导方程,得到在高功率808 nm泵浦光抽运下产生946 nm激光的单晶光纤温度场分布,并与传统Nd∶YAG激光晶体的温度场进行比较,然后分别与同泵浦条件下的有限元数值方法的分析结果进行研究对比,最后分析泵浦光参数、单晶光纤参数等对温度场的影响。结果表明,功率为86 W的泵浦光入射至单晶光纤端面的最高温升仅为30.98℃,明显优于同泵浦条件下传统Nd∶YAG晶体的端面温升结果94.37℃,与有限元数值法得到的Nd:YAG单晶光纤19℃温升结果相比,该解析法结果更接近于实验的测量值31℃,能够更精确描述晶体光纤温度场。本文可对单晶光纤激光器热效应的精确研究提供一定参考,进而有利于提高单晶光纤激光器的性能。     

钛宝石激光器端面抽运Nd:YAG陶瓷激光器热沉积理论和实验研究

通过热沉积系数研究在激光提取条件下掺杂原子分数为1.0%的Nd:YAG陶瓷激光器中热沉积问题.热沉积系数定义为热沉积功率与激光器输出功率之比.在理论分析基础上，通过测量激光器斜率效率来间接测定热沉积系数，实验测定的热沉积系数值为0.63.建立激光提取条件下Nd:YAG陶瓷发热模型，讨论了影响热沉积系数的主要因素.结果表明：热沉积系数对Nd:YAG陶瓷的辐射量子效率、交叠效率以及激光提取效率的变化非常敏感.为有效减少介质内热沉积，在激光器优化设计中交叠效率和激光提取效率是需要着重考虑的参数.所得结果可为进一步研究陶瓷激光器中热效应提供参考. 关键词： 热沉积 Nd:YAG陶瓷 固体激光器     

678 nm RTP electro-optical Q-switched ceramic laser

The RTP electro-optical Q-switched ceramic laser at the wavelength of 678 nm with narrow pulse width is studied. We used the laser diode arrays side-pumped Nd:YAG ceramic crystal with 1.1 at% Nd doping and dimensions of Φ3 mm × 50 mm, designed folding cavity parameters, and discussed the variation of the beam radius in the ceramic crystal and frequency doubling crystal with the thermal focal length of ceramic crystal or KTP crystal. By using double RTP crystals as electro-optic Q-switch and KTP crystal type II phase matching for intracavity frequency-doubling, a narrow pulse width electro-optical Q-switched Nd:YAG ceramic laser was obtained. The output energy of 0.9 mJ and the pulse width of 41.6 ns at 678 nm are obtained at the repetition rate of 1000 Hz and pumped power of 144 W. The results formed the basis for the further development of the high power and high efficiency ceramic red laser.     

660 nm单一波长Nd:YAG陶瓷激光器

 针对陶瓷晶体1319 nm的谱线设计了适合的谐振腔腔镜膜系参量,采用激光二极管列阵侧向抽运掺杂1.1at%、Φ3×50 mm的Nd:YAG陶瓷,利用色散棱镜及KTP晶体Ⅱ类匹配腔内倍频,研制了一台660 nm单一波长输出的高重频Nd:YAG陶瓷红光激光器.根据陶瓷晶体的热透镜焦距设计了谐振腔的各个参量,在重复频率为1000 Hz、单脉冲抽运能量约144 mJ时,获得了3.9 mJ的660 nm脉冲激光输出,总的光-光转换效率为2.71%.为进一步研究大功率、高效率的陶瓷红光激光器奠定了基础.     

高峰值功率KDP晶体四倍频266nm紫外激光器

报道了一种灯泵浦结构的Nd:YAG晶体电光调Q高峰值功率266nm紫外激光器。结合磷酸二氢钾(KDP)晶体性质,基于倍频理论,分析了考虑走离效应情况下存在相位失配量时KDP晶体长度对转换效率的影响。该激光器采用紧凑的平平腔结构,灯泵浦Nd:YAG晶体电光调Q 1064nm激光作为基频光,腔外采用Ⅱ类匹配磷酸钛氧钾(KTP)和Ⅰ类匹配KDP分别作为二倍频和四倍频晶体。利用能量计、示波器等仪器进行测量,激光器重复频率1Hz时,获得脉宽6.0ns,单脉冲能量35mJ的266nm紫外激光输出,峰值功率高达5.83 MW;当重复频率10Hz时,获得单脉冲能量28.9mJ的266nm紫外激光。532~266nm转换效率最高可达31.9%。利用该高峰值功率、窄脉宽266nm紫外激光器,能够实现激光打标、激光雕刻。     

Dual-polarization electro-optical Q-switched ceramic laser

A dual-polarization electro-optical Q-switched Nd:YAG ceramic laser was studied. By selecting the appropriate size of calcite crystals, the dual-polarization Q-switched pulse was achieved by characteristics of calcite crystal. Experimental results show that compared with the traditional single-polarization electro-optical Q-switched laser, insertion loss is reduced, dynamic to static ratio is greatly improved, thermally induced birefringence of electro-optical Q-switched Nd:YAG ceramic laser is effective compensated. The output power of 19 W and the pulse width of 13 ns are obtained at the repetition rate of 1 kHz and pumped power of 144 W. The dynamic to static ratio is 71%. The results formed the basis for the further development of the high power and high efficiency ceramic red laser.     

1.57 MW peak power pulses generated by a diode-pumped Q-switched Nd:LuAG ceramic laser

The pulse characteristics of a laser diode dual-end-pumped electro-optic Q-switched Nd:LuAG ceramic laser at various repetition rates are presented. The largest output pulse energy of 11 mJ is realized at the repetition rate of 100 Hz with pump energy of 84.3 mJ, and the slope efficiency in respect to pump pulse energy is 18.6%. The single pulse peak power reaches up to 1.57 MW. Using Nd:LuAG ceramic as the amplification medium seeded by an Nd:YAG laser of 5.2 mJ, a 10.3 mJ amplified pulse is obtained with pump pulse energy of 42.8 mJ, corresponding to an extraction efficiency of 11.9%.     

多波长半导体激光阵列端泵Nd:YAG脉冲激光器

研制了无温控多波长激光二极管阵列端面泵浦Nd：YAG电光调Q激光器。采用4 000 W多波长准连续激光二极管阵列作为泵浦源,快轴准直镜与透镜导管作为泵浦耦合系统,端面泵浦φ6 mm×60 mm的Nd：YAG晶体,并采用RTP晶体进行电光调Q实验。在重复频率5 Hz、室温（25℃）时,激光器获得了最大输出能量74.4 mJ、脉宽15 ns的1 064 nm脉冲激光输出,光光转换效率达到11%。在25~55℃的工作温度下,对多波长LDA的光谱特征与激光器的输出特性作了测试,激光器输出能量随着工作温度的上升而先迅速下降再逐步保持稳定,当重复频率分别为5 Hz和10 Hz时,激光器对应的最低输出能量分别为48 mJ与37 mJ。     

Diode-pumped Ba(NO3)2 and NaBrO3 Raman lasers

A Q-switched Nd:YAG laser transversely pumped with a 300-W quasi-cw diode generated pulses at 1.06 7m with intracavity energies of up to 10 mJ. Intracavity Raman shifting in a 60-mm-long Ba(NO₃)₂ crystal led to pulses with energies of 2.5 mJ at 1197 nm. The output pulse duration was reduced to 8.5 ns compared to 50 ns at the fundamental wavelength. Beam quality improvement was observed. A NaBrO₃ Raman laser generated pulse energies of 0.4 mJ at 1163 nm with a crystal of only 18 mm length. The Raman radiation was frequency doubled into the yellow spectral region from 580 nm to 599 nm, which is difficult to reach with other solid-state lasers.     

二极管泵浦折叠式电光调Q激光器

针对机载激光测距及激光指示应用需求,设计了一种紧凑可靠的电光调Q脉冲激光器。从调Q速率方程出发,分析了激光器输出能量随优化参数z增大而增大、脉宽随z增大而减小的关系。采用?6 mm×56 mm的Nd:YAG激光晶体,LD侧面泵浦,角锥棱镜作为折光器的u形折叠式非稳腔,在增益满足的前提下,提高谐振腔抗失调能力。在注入电脉冲1.2 J条件下,激光器单脉冲能量输出为108 mJ,脉冲宽度为11.8 ns,能量不稳定度 < 0.8%;光-光效率18%,可长时间稳定运行。     

Intracavity optical parametric oscillator pumped by passively Q-switched Nd:YLF laser

We report on a passively Q-switched end pumped Nd:YLF laser including a noncritically phase-matched KTP singly resonant intracavity optical parametric oscillator (IOPO-KTP). For the Q-switching operation we have used Cr:YAG saturable absorber. The optimized passively Q-switched Nd:YLF laser without IOPO generated linearly polarized pulses of 11.5 ns and 1.07 mJ at 1047 nm. The conversion efficiency of the optimized Q-switched pulse energy at 1047 nm to 1547 nm of a signal approached about 47%. For optimizing both Nd:YLF laser and IOPO we have numerically solved a theoretical model. We have achieved 1.6-ns duration pulses at 1547 nm with energy of 0.5 mJ and peak power of above 300 kW. The beam quality was excellent (M² ≈1).     

Laser-diode-pumped Nd:YVO<Subscript>4</Subscript>/Nd:YAG MOPA burst-mode laser

We report a high-repetition-rate, high-peak-power laser diode (LD) pumped burst-mode 1064 nm laser from a Nd:YVO₄/Nd:YAG master oscillator power amplifier. 10–100 kHz pulse burst in a duration up to 2 ms is achieved in LD end-pumped Nd:YVO₄ acousto-optically Q-switched laser. After amplification with LD side-pumped Nd:YAG rod amplifiers, the single pulse energy reaches 73 mJ in 10 kHz pulse burst laser with a peak power of 7.8 MW.