The synthesis and electrochemical characterization of novel polymers bearing phenoxyl‐radicals as redox‐active side chains is described. The monomers are synthesized from the corresponding phenols and quinones, respectively. These compounds are subsequently polymerized via ring‐opening metathesis polymerization. The electrochemical properties of the phenoxyl‐radical polymers are characterized using cyclic voltammetry and the most promising polymer is investigated as active material in a lithium coin‐cell, creating the first phenoxyl‐lithium battery. These phenoxyl‐containing polymers represent interesting anode materials for organic radical and lithium batteries due to their suitable redox‐potentials and possibility to create batteries with higher potentials as well as straightforward synthesis procedures.
Controlling self‐assembly behaviors of liquid crystals is a fundamental issue for designing them as intelligent actuators. Here, anisotropic porous polyvinylidene fluoride film is utilized as a template to induce homogeneous alignment of liquid crystals. The mechanism of liquid crystal alignment induced by anisotropic porous polyvinylidene fluoride film is illustrated based on the relationship between the alignment behavior of liquid crystals and surface microstructure of anisotropic polyvinylidene fluoride film. Liquid crystal elastomer actuators with fast responsiveness, large strain change, and reversible actuation behaviors are achieved by the photopolymerization of liquid crystal monomer in liquid crystal cells coated with anisotropic porous films.
Five three‐component chiral polymers incorporating (S )‐1,1′‐binaphthyl, tetraphenylethene (TPE) and fluorene moieties are designed and synthesized by Pd‐catalyzed Sonogashira reaction. All these polymers show obvious aggregation induced emission enhancement response behavior in the fluorescence emission region of 460–480 nm. Interestingly, three of them show aggregation‐induced circularly polarized luminescence (AICPL) signals in tetrahydrofuran–H2O mixtures. Most importantly, these AICPL signals can be tuned by changing the molar ratios of TPE and fluorene components through fluorescence resonance energy transfer and give the highest glum = ±4.0 × 10−3. This work provides a novel strategy for developing AICPL‐enhanced materials.
A group of crosslinked cyclic siloxane (Si O) and silazane (Si N) polymers are synthesized via solvent‐free initiated chemical vapor deposition (iCVD). Notably, this is the first report of cyclic polysilazanes synthesized via the gas‐phase iCVD method. The deposited nanoscale thin films are thermally stable and chemically inert. By iCVD, they can uniformly and conformally cover nonplanar surfaces having complex geometry. Although polysiloxanes are traditionally utilized as dielectric materials and insulators, our research shows these cyclic organosilicon polymers can conduct lithium ions (Li+) at room temperature. The conformal coating and the room temperature ionic conductivity make these cyclic organosilicon polymers attractive for use as thin‐film electrolytes in solid‐state batteries. Also, their synthesis process and properties have been systemically studied and discussed.
Hierarchical semicrystalline block copolymer nanoparticles are produced in a segmented gas‐liquid microfluidic reactor with top‐down control of multiscale structural features, including nanoparticle morphologies, sizes, and internal crystallinities. Control of multiscale structure on disparate length scales by a single control variable (flow rate) enables tailoring of drug delivery nanoparticle function including release rates.
Biaxially oriented polypropylene (BOPP) is widely used in packaging. Although its orientation increases mechanical strength and clarity, BOPP suffers from a high oxygen transmission rate (OTR). Multilayer thin films are deposited from water using layer‐by‐layer (LbL) assembly. Polyethylenimine (PEI) is combined with either poly(acrylic acid) (PAA) or vermiculite (VMT) clay to impart high oxygen barrier. A 30‐bilayer PEI/VMT nanocoating (226 nm thick) improves the OTR of 17.8 μm thick BOPP by more than 30X, rivaling most inorganic coatings. PEI/PAA multilayers achieve comparable barrier with only 12 bilayers due to greater thickness, but these films exhibit increased oxygen permeability at high humidity. The PEI/VMT coatings actually exhibit improved oxygen barrier at high humidity (and also improve moisture barrier by more than 40%). This high barrier BOPP meets the criteria for sensitive food and some electronics packaging applications. Additionally, this water‐based coating technology is cost effective and provides an opportunity to produce high barrier polypropylene film on an industrial scale.
Messenger ribonucleic acids (mRNAs) are considered as promising alternatives for transient gene therapy, but to overcome their poor pharmacokinetic properties, smart carriers are required for cellular uptake and stimuli‐responsive release. In this work, a synthetic concept toward reductive decationizable cationic block copolymers for mRNA complexation is introduced. By combination of RAFT block copolymerization with postpolymerization modification, cationic block copolymers are generated with disulfide‐linked primary amines. They allow effective polyplex formation with negatively charged mRNA and subsequent release under reductive conditions of the cytoplasm. In first in vitro experiments with fibroblasts and macrophages, tailor‐made block copolymers mediate cell‐specific mRNA transfection, as quantified by polyplex uptake and mRNA‐encoding gene expression. Furthermore, RAFT polymerization provides access to heterotelechelic polymers with orthogonally addressable endgroup functionalities utilized to ligate targeting units onto the polyplex‐forming block copolymers. The results exemplify the broad versatility of this reductive decationizable mRNA carrier system, especially toward further advanced mRNA delivery applications.
Pentacyclic lactam acceptor unit TPTI invented by our group is proved to be a good building block for efficient D‐A copolymers used in organic solar cells. Here, two D‐A copolymers PBTTPTI and PTTTPTI are developed by copolymerizing TPTI with 2,2′‐bithiophene (BT) or thieno[3,2‐b]thiophene (TT). PBTTPTI and PTTTPTI exhibit good solubility and strong interchain π–π interaction even in dilute solution. They possess deep HOMO levels (ca. ‐5.3 eV), partial crystallinity, and good hole mobilities. Blending with PC71BM, PBTTPTI and PTTTPTI give decent power conversion efficiencies (PCE) up to 6.83% and 5.86%, with outstanding fill factors (FF) of 74.3% and 71.3%, respectively.
Microfluidic devices, which can continuously fabricate single emulsion with monodispersed droplets having a pore diameter of more than 100 μm in large numbers, can be applied to manufacture ordered macroporous films. 3D ordered macroporous films with a diameter of more than 100 μm can be fabricated using ordered arrays of the monodispersed droplets as templates of the macropores, which are self‐assembled in the space between two parallel flat glass plates. As the gap between the glass plates increases, the number of the layer increases. Furthermore, in the case with two or more layers, the lattice structure of the macroporous films also changes due to the confinement effects.
Synthesis of a cyclodextrin (CD) polyrotaxane is achieved for the first time by simultaneous free radical polymerization of isoprene, threading by CD, and stoppering by copolymerization of styrene. This reaction is performed in an eco‐friendly manner in an aqueous medium similar to classical emulsion polymerization. Threaded CD rings of the polyrotaxane are cross‐linked by hexamethylene diisocyanate, leading to highly elastic slide‐ring gels.
A novel method, epoxidation/reduction of vegetable oils, is developed to prepare bio‐based polyols for the manufacture of polyurethanes (PUs). These polyols are synthesized from castor oil (CO), epoxidized soybean oil, and epoxidized linseed oil and their molecular structures are characterized. They are used to prepare a variety of PUs, and their thermomechanical properties are compared to those of PU made with petroleum‐based polyol (P‐450). It is shown that PUs made with polyols from soybean and linseed oil exhibit higher glass transition temperatures, tensile strength, and Young's modulus and PU made with polyol from CO exhibits higher elongation at break and toughness than PU made with P‐450. However, PU made with P‐450 displays better thermal resistance because of tri‐ester structure and terminal functional groups. The method provides a versatile way to prepare bio‐polyols from vegetable oils, and it is expected to partially or completely replace petroleum‐based polyols in PUs manufacture.
Rapid, large‐scale exfoliation of graphene in water has expanded its potential for use outside niche applications. This work focuses on utilizing aqueous graphene dispersions to form thin films using layer‐by‐layer processing, which is an effective method to produce large‐area coatings from water‐based solutions of polyelectrolytes. When layered with polyethyleneimine, graphene flakes stabilized with cholate are shown to be capable of producing films thinner than 100 nm. High surface coverage of graphene flakes results in electrical conductivity up to 5500 S m−1. With the relative ease of processing, the safe, cost effective nature of the ingredients, and the scalability of the deposition method, this system should be industrially attractive for producing thin conductive films for a variety of electronic and antistatic applications.
The novel hyperbranched poly(methyl acrylate)‐block‐poly(acrylic acid)s (HBPMA‐b‐PAAs) are successfully synthesized via single‐electron transfer‐living radical polymerization (SET‐LRP), followed with hydrolysis reaction. The copolymer solution could spontaneously form unimolecular micelles composed of the hydrophobic core (PMA) and the hydrophilic shell (PAA) in water. Results show that the size of spherical particles increases from 8.18 to 19.18 nm with increased pH from 3.0 to 12.0. Most interestingly, the unique regular quadrangular prisms with the large microstructure (5.70 μm in length, and 0.47 μm in width) are observed by the self‐assembly of unimolecular micelles when pH value is below 2. Such self‐assembly behavior of HBPMA‐b‐PAA in solution is significantly influenced by the pH cycle times and concentration, which show that increased polymer concentration favors aggregate growth.
The surface of polyacrylonitrile (PAN) film is treated with ethyleneamines (EDA) in a simple chemical vapor phase reaction. Successful introduction of amine functional groups on the cyano group of PAN backbone is verified by FT‐IR and NMR measurements. Further UV‐vis and photoluminescence analyses show a red shift of the emission peak after repeated EDA treatment, which might be attributed to the formation of imine conjugation from newly formed carbon‐nitrogen bonds on the PAN backbone. Further confocal laser scanning microscopy reveals that selective patterning of EDA on PAN films is possible via local polydimethylsiloxane masking. The results indicate that both chemical and optical patterning on PAN film can be realized via a single reaction and show the potential of this novel methodology in selective patterning.
Multilayer coatings consisting of oppositely charged polyelectrolytes have proven to be extraordinarily effective oxygen barriers but require many processing steps to fabricate. In an effort to prepare high oxygen barrier thin films more quickly, a polyelectrolyte complex coacervate composed of polyethylenimine and polyacrylic acid is prepared. The coacervate fluid is applied as a thin film using a rod coating process. With humidity and thermal post‐treatment, a 2 µm thin film reduces the oxygen transmission rate of 0.127 mm poly(ethylene terephthalate) by two orders of magnitude, rivalling conventional oxygen barrier technologies. These films are fabricated in ambient conditions using low‐cost, water‐based solutions, providing a tremendous opportunity for single‐step deposition of polymeric high barrier thin films.
Metallocenes are organometallic compounds with reversible redox profiles and tunable oxidation and reduction potentials, depending on the metal and substituents at the cyclopentadienyl rings. Metallocenes have been introduced in macromolecules to combine the redox‐activity with polymer properties. There are many examples of such hydrophobic polymer materials, but much fewer water‐soluble examples are found scattered across the polymer literature. However, in terms of drug delivery and other biological applications, water solubility is essential. For this very reason, all the synthetic routes to water‐soluble metallocene containing polymers are collected and discussed here. The focus is on neutral ferrocene‐ and ruthenocene‐containing and charged cobaltocenium‐containing macromolecules (i.e., symmetrical sandwich complexes). The synthetic protocols, self‐assembly behavior, and other benefits of the obtained materials are discussed.
Based on a water‐in‐oil‐in‐water emulsion system, porous and hollow polydimethylsiloxane (PDMS) beads containing cells using a simple fluidic device with three flow channels are fabricated. Poly(ethylene glycol) (PEG) in the PDMS oil phase is served as a porogen for pore development. The feasibility of the porous PDMS beads prepared with different PEG concentrations (10, 20, and 30 wt%) for cell encapsulation in terms of pore size, protein diffusion, and cell proliferation inside the PDMS beads is evaluated. The PDMS beads prepared with PEG 30 wt% are exhibited a highly porous structure and facilitated fast diffusion of protein from the core domain to the outer phase, eventually leading to enhanced cell proliferation. The results clearly indicate that hollow PDMS beads with a porous structure could provide a favorable microenvironment for cell survival due to the large porous structure.
A triptycene‐based microporous organic polymer (MOP) in which 2,6‐bis(benzimidazol‐2‐yl)pyridine (bbp) is incorporated as linkage and coordination site is designed and synthesized. Pd(II) ions are further immobilized in this MOP through the coordination interactions between Pd(II) ion and nitrogen atoms of bbp. The resulting material shows high stability and exhibits excellent heterogeneously catalytic activity for the Suzuki–Miyaura cross‐coupling reaction. Its high efficiency can be maintained after being reused for a number of cycles.
Polysaccharides are abundant in nature, renewable, nontoxic, and intrinsically biodegradable. They possess a high level of functional groups including hydroxyl, amino, and carboxylic acid groups. These functional groups can be utilized for further modification of polysaccharides with small molecules, polymers, and crosslinkers; the modified polysaccharides have been used as effective building blocks in fabricating novel biomaterials for various biomedical applications such as drug delivery carriers, cell‐encapsulating biomaterials, and tissue engineering scaffolds. This review describes recent strategies to modify polysaccharides for the development of polysaccharide‐based biomaterials; typically self‐assembled micelles, crosslinked microgels/nanogels, three‐dimensional hydrogels, and fibrous meshes. In addition, the outlook is briefly discussed on the important aspects for the current and future development of polysaccharide‐based biomaterials, particularly tumor‐targeting intracellular drug delivery nanocarriers.
High‐performance catalysts and photovoltaics are required for building an environmentally sustainable society. Because catalytic and photovoltaic reactions occur at the interfaces between reactants and surfaces, the chemical, physical, and structural properties of interfaces have been the focus of much research. To improve the performance of these materials further, inorganic porous materials with hierarchic porous architectures have been fabricated. The breath figure technique allows preparing porous films by using water droplets as templates. In this study, a valuable preparation method for hierarchic porous inorganic materials is shown. Hierarchic porous materials are prepared from surface‐coated inorganic nanoparticles with amphiphilic copolymers having catechol moieties followed by sintering. Micron‐scale pores are prepared by using water droplets as templates, and nanoscale pores are formed between the nanoparticles. The fabrication method allows the preparation of hierarchic porous films from inorganic nanoparticles of various shapes and materials.
