Fundamental science, as well as all communications and navigation systems, are heavily reliant on the phase, timing, and synchronization provided by low‐noise and agile frequency sources. Although research into varied photonic and electronic schemes have strived to improve upon the spectral purity of microwave and millimeter‐wave signals, the reliance on conventional electronic synthesis for tuning has resulted in limited progress in broadband sources. Using a digital‐photonic synthesizer architecture that derives its time‐base from a high‐stability optical reference cavity, we generate frequency‐agile and wideband microwave signals with exceptional dynamic range and with a fractional frequency instability of 1 × 10−15 at 1 s. The presented architecture demonstrates digitally controlled, user defined and broadband frequency tuning from RF to 100 GHz with orders‐of‐magnitude improvement in noise performance over room‐temperature electronic wide‐bandwidth synthesis schemes.
This article presents a novel III‐V on silicon laser. This work exploits the phenomenon that a passive silicon cavity, side‐coupled to a III‐V waveguide, will provide high and narrow‐band reflectivity into the III‐V waveguide: the resonant mirror. This results in an electrically pumped laser with a threshold current of 4 mA and a side‐mode suppression ratio up to 48 dB.
Femtosecond laser machining has been widely used for fabricating arbitrary 2.5 dimensional (2.5D) structures. However, it suffers from the problems of low fabrication efficiency and high surface roughness when processing hard materials. To solve these problems, we propose a dry‐etching‐assisted femtosecond laser machining (DE‐FsLM) approach in this paper. The fabrication efficiency could be significantly improved for the formation of complicated 2.5D structures, as the power required for the laser modification of materials is lower than that required for laser ablation. Furthermore, the surface roughness defined by the root‐mean‐square improved by an order of magnitude because of the flat interfaces of laser‐modified regions and untreated areas as well as accurate control during the dry‐etching process. As the dry‐etching system is compatible with the IC fabrication process, the DE‐FsLM technology shows great potential for application in the device integration processing industry.
Near‐field optical microscopy techniques provide information on the amplitude and phase of local fields in samples of interest in nanooptics. However, the information on the near field is typically obtained by converting it into propagating far fields where the signal is detected. This is the case, for instance, in polarization‐resolved scattering‐type scanning near‐field optical microscopy (s‐SNOM), where a sharp dielectric tip scatters the local near field off the antenna to the far field. Up to now, basic models have interpreted S‐ and P‐polarized maps obtained in s‐SNOM as directly proportional to the in‐plane ( or ) and out‐of‐plane () near‐field components of the antenna, respectively, at the position of the probing tip. Here, a novel model that includes the multiple‐scattering process of the probing tip and the nanoantenna is developed, with use of the reciprocity theorem of electromagnetism. This novel theoretical framework provides new insights into the interpretation of s‐SNOM near‐field maps: the model reveals that the fields detected by polarization‐resolved interferometric s‐SNOM do not correlate with a single component of the local near field, but rather with a complex combination of the different local near‐field components at each point (, and ). Furthermore, depending on the detection scheme (S‐ or P‐polarization), a different scaling of the scattered fields as a function of the local near‐field enhancement is obtained. The theoretical findings are corroborated by s‐SNOM experiments which map the near field of linear and gap plasmonic antennas. This new interpretation of nanoantenna s‐SNOM maps as a complex‐valued combination of vectorial local near fields is crucial to correctly understand scattering‐type near‐field microscopy measurements as well as to interpret the signals obtained in field‐enhanced spectroscopy.
A novel approach to facilitate excitation and readout processes of isolated negatively charged nitrogen‐vacancy (NV) centers is proposed. The approach is based on the concept of all‐dielectric nanoantennas. It is shown that the all‐dielectric nanoantenna can significantly enhance both the emission rate and emission extraction efficiency of a photoluminescence signal from a single NV center in a diamond nanoparticle on a dielectric substrate. The proposed approach provides high directivity, large Purcell factor, and efficient beam steering, thus allowing an efficient far‐field initialization and readout of several NV centers separated by subwavelength distances.
Monocrystalline titanium dioxide (TiO2) micro‐spheres support two orthogonal magnetic dipole modes at terahertz (THz) frequencies due to strong dielectric anisotropy. For the first time, we experimentally detected the splitting of the first Mie mode in spheres of radii m through near‐field time‐domain THz spectroscopy. By fitting the Fano lineshape model to the experimentally obtained spectra of the electric field detected by the sub‐wavelength aperture probe, we found that the magnetic dipole resonances in TiO2 spheres have narrow linewidths of only tens of gigahertz. Anisotropic TiO2 micro‐resonators can be used to enhance the interplay of magnetic and electric dipole resonances in the emerging THz all‐dielectric metamaterial technology.
We report complete spatial shaping (both phase and amplitude) of the second‐harmonic beam generated in a nonlinear photonic crystal. Using a collinear second‐order process in a nonlinear computer generated hologram imprinted on the crystal, the desired beam is generated on‐axis and in the near field. This enables compact and efficient one‐dimensional beam shaping in comparison to previously demonstrated off‐axis Fourier holograms. We experimentally demonstrate the second‐harmonic generation of high‐order Hermite–Gauss, top hats and arbitrary skyline‐shaped beams.
We report on the theoretical investigation of plasmonic resonances in metallic Möbius nanorings. Half‐integer numbers of resonant modes are observed due to the presence of an extra phase π provided by the topology of the Möbius nanostrip. Anomalous plasmon modes located at the non‐orientable surface of the Möbius nanoring break the symmetry that exist in conventional ring cavities, thus enable far‐field excitation and emission as bright modes. The far‐field resonant wavelength as well as the feature of half‐integer mode numbers is constant to the change of charge distribution on the Möbius nanoring due to the topology of Möbius ring. Owing to the ultra‐small mode volume induced by the remaining dark feature, an extremely high sensitivity as well as a remarkable figure of merit is obtained in our numerical calculations for sensing performance. The topological metallic nanostructure provides a novel platform for the investigation of localized surface plasmon modes exhibiting unique phenomena for potential plasmonic applications.
Use of resonant light forces opens up a unique approach to high‐volume sorting of microspherical resonators with much higher uniformity of resonances compared to that in coupled‐cavity structures obtained by the best semiconductor technologies. In this work, the spectral response of the propulsion forces exerted on polystyrene microspheres near tapered microfibers is directly observed. The measurements are based on the control of the detuning between the tunable laser and internal resonances in each sphere with accuracy higher than the width of the resonances. The measured spectral shape of the propulsion forces correlates well with the whispering‐gallery mode resonances in the microspheres. The existence of a stable radial trap for the microspheres propelled along the taper is demonstrated. The giant force peaks observed for 20‐μm spheres are found to be in a good agreement with a model calculation demonstrating an efficient use of the light momentum for propelling the microspheres.
Spatial overlap between the electromagnetic fields and the analytes is a key factor for strong light‐matter interaction leading to high sensitivity for label‐free refractive index sensing. Usually, the overlap and therefore the sensitivity are limited by either the localized near field of plasmonic antennas or the decayed resonant mode outside the cavity applied to monitor the refractive index variation. In this paper, by constructing a metal microstructure array‐dielectric‐metal (MDM) structure, a novel metamaterial absorber integrated microfluidic (MAIM) sensor is proposed and demonstrated in terahertz (THz) range, where the dielectric layer of the MDM structure is hollow and acts as the microfluidic channel. Tuning the electromagnetic parameters of metamaterial absorber, greatly confined electromagnetic fields can be obtained in the channel resulting in significantly enhanced interaction between the analytes and the THz wave. A high sensitivity of 3.5 THz/RIU is predicted. The experimental results of devices working around 1 THz agree with the simulation ones well. The proposed idea to integrate metamaterial and microfluid with a large light‐matter interaction can be extended to other frequency regions and has promising applications in matter detection and biosensing.
A scheme for active temporal‐to‐spatial demultiplexing of single photons generated by a solid‐state source is introduced. The scheme scales quasi‐polynomially with photon number, providing a viable technological path for routing n photons in the one temporal stream from a single emitter to n different spatial modes. Active demultiplexing is demonstrated using a state‐of‐the‐art photon source—a quantum‐dot deterministically coupled to a micropillar cavity—and a custom‐built demultiplexer—a network of electro‐optically reconfigurable waveguides monolithically integrated in a lithium niobate chip. The measured demultiplexer performance can enable a six‐photon rate three orders of magnitude higher than the equivalent heralded SPDC source, providing a platform for intermediate quantum computation protocols.
Quantitative phase imaging (QPI), a method that precisely recovers the wavefront of an electromagnetic field scattered by a transparent, weakly scattering object, is a rapidly growing field of study. By solving the inverse scattering problem, the structure of the scattering object can be reconstructed from QPI data. In the past decade, 3D optical tomographic reconstruction methods based on QPI techniques to solve inverse scattering problems have made significant progress. In this review, we highlight a number of these advances and developments. In particular, we cover in depth Fourier transform light scattering (FTLS), optical diffraction tomography (ODT), and white‐light diffraction tomography (WDT).
The ferroelectric domain structures of periodically poled KTiOPO4 and two‐dimensional short range ordered poled LiNbO3 crystals are determined non‐invasively by interferometric measurements of the electro‐optically induced phase retardation. Owing to the sign reversal of the electro‐optical coefficients upon domain inversion, a π phase shift is observed for the inverted domains. The microscopic setup provides diffraction‐limited spatial resolution allowing us to reveal the nonlinear and electro‐optical modulation patterns in ferroelectric crystals in a non‐destructive manner and to determine the poling period, duty cycle and short‐range order as well as detect local defects in the domain structure. Conversely, knowing the ferroelectric domain structure, one can use electro‐optical microscopy so as to infer the distribution of the electric field therein.
In the development of microfluidic chips, conventional 2D processing technologies contribute to the manufacturing of basic microchannel networks. Nevertheless, in the pursuit of versatile microfluidic chips, flexible integration of multifunctional components within a tiny chip is still challenging because a chip containing micro‐channels is a non‐flat substrate. Recently, on‐chip laser processing (OCLP) technology has emerged as an appealing alternative to achieve chip functionalization through in situ fabrication of 3D microstructures. Here, the recent development of OCLP‐enabled multifunctional microfluidic chips, including several accessible photochemical/photophysical schemes, and photosensitive materials permiting OCLP, is reviewed. To demonstrate the capability of OCLP technology, a series of typical micro‐components fabricated using OCLP are introduced. The prospects and current challenges of this field are discussed.
We experimentally demonstrate an optically‐pumped III‐V/Si vertical‐cavity laser with lateral emission into a silicon waveguide. This on‐chip hybrid laser comprises a distributed Bragg reflector, a III‐V active layer, and a high‐contrast grating reflector, which simultaneously funnels light into the waveguide integrated with the laser. This laser has the advantages of long‐wavelength vertical‐cavity surface‐emitting lasers, such as low threshold and high side‐mode suppression ratio, while allowing integration with silicon photonic circuits, and is fabricated using CMOS compatible processes. It has the potential for ultrahigh‐speed operation beyond 100 Gbit/s and features a novel mechanism for transverse mode control.
Microresonator‐based Kerr frequency comb (microcomb) generation can potentially revolutionize a variety of applications ranging from telecommunications to optical frequency synthesis. However, phase‐locked microcombs have generally had low conversion efficiency limited to a few percent. Here we report experimental results that achieve conversion efficiency ( on‐chip comb power excluding the pump) in the fiber telecommunication band with broadband mode‐locked dark‐pulse combs. We present a general analysis on the efficiency which is applicable to any phase‐locked microcomb state. The effective coupling condition for the pump as well as the duty cycle of localized time‐domain structures play a key role in determining the conversion efficiency. Our observation of high efficiency comb states is relevant for applications such as optical communications which require high power per comb line.
A diode‐pumped Yb:YAG MOPA‐System for the unprecedented generation of transform limited pulses with variable pulse duration in the range between 10 ps and 100 ps is presented. First applications relying on unique pulse parameters as modulation free spectrum, tunability and coherence length, namely the direct laser interference patterning (DLIP) and laser cooling of stored relativistic ion beams are highlighted. Pulses are generated by a mode‐locked fs‐oscillator while the spectral bandwidth is narrowed in the subsequent regenerative amplifier by an intra‐cavity grating monochromator. Two alternative booster amplifiers were added to increase the pulse energy to 100 μJ and 10 mJ, respectively.
High power single mode quantum cascade lasers with a narrow far field are important for several applications including surgery or military countermeasure. Existing technologies suffer from drawbacks such as operation temperature and scalability. In this paper we introduce a fabrication approach that potentially solves simultaneously these remaining limitations. We demonstrate and characterize deep etched, buried photonic crystal quantum cascade lasers emitting around a wavelength of 8.5 μm. The active region was dry etched before being regrown with semi‐insulating Fe:InP. This fabrication strategy results in a refractive index contrast of 10% allowing good photonic mode control, and simultaneously provides good thermal extraction during operation. Single mode emission with narrow far field pattern and peak powers up to 0.88 W at 263 K were recorded from the facet of the photonic crystal laser, and lasing operation was maintained up to room temperature. The lasing modes emitted from square photonic crystal mesas with a side length of 550μm, were identified as slow Bloch photonic crystal modes by means of three‐dimensional photonic simulations and measurements.
We demonstrate a scheme incorporating dual‐coupled microresonators through which mode interactions are intentionally introduced and controlled for Kerr frequency comb (microcomb) generation in the normal‐dispersion region. Microcomb generation, repetition rate selection, and mode locking are achieved with coupled silicon nitride microrings controlled via an on‐chip microheater. The proposed scheme shows for the first time a reliable design strategy for normal‐dispersion microcombs and may make it possible to generate microcombs in an extended wavelength range (e.g. in the visible) where normal material dispersion is likely to dominate.
An all‐optical phase modulation method for the linear readout of integrated interferometric biosensors is demonstrated, merging simple intensity detection with the advantages offered by spectral interrogation. The phase modulation is introduced in a simple and cost‐effective way by tuning a few nanometers the emission wavelength of commercial laser diodes, taking advantage of their well‐known drawback of power–wavelength dependence. The method is applied to the case of a bimodal waveguide (BiMW) interferometric biosensor, fabricated with standard silicon technology and operated at visible wavelengths, rendering a detection limit of refractive index units for bulk sensing. The biosensing capabilities of the phase‐linearized BiMW device are assessed through the quantitative immunoassay of C‐reactive protein, a key protein in inflammatory processes. This method can be applied to any modal interferometer.
