Characterization of Y<Subscript>2</Subscript>BaCuO<Subscript>5</Subscript> nanoparticles synthesized by nano-emulsion method

Nanoscale yttrium–barium–copper oxide (Y₂BaCuO₅, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3–8 nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influence of salt (Y₂(NO₃)₃) content on the droplet size was investigated and the addition of salt reduced the droplet size. The effects of reaction time and temperature on the Y211 particle sizes were also investigated. The particles were characterized using the TEM, SEM, and XRD. Nanoparticles produced by the nano-emulsion method were calcined at 850°C to form the Y211 phase as compared to solid state processing temperature of 1050°C. Based on the TEM analysis, the average diameter of the Y211 particles produced using the nano-emulsion method was in the range of 30–100 nm. The effect of adding 15% Y211 nanoparticles to the superconductor YBCO-123 as flux pinning centers, was investigated, and the transition temperature was reduced by 3 K.     

One-step synthesis of colloidal Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles at room temperature

A facile room-temperature synthesis has been developed to prepare colloidal Mn₃O₄ and γ-Fe₂O₃ nanoparticles (5 to 25 nm) by an ultrasonic-assisted method in the absence of any additional nucleation and surfactant. The morphology of the as-prepared samples was observed by transmission electron microscopy. High-resolution transmission electron microscopy observations revealed that the as-synthesized nanoparticles were single crystals. The magnetic properties of the samples were investigated with a superconducting quantum interference device magnetometer. The possible formation process has been proposed.     

Influence of the sample orientation in Sn<Subscript>2</Subscript>P<Subscript>2</Subscript>S<Subscript>6</Subscript> crystals on the hydrostatic piezoelectric coefficients

The influence of the sample orientation on the effective value of the hydrostatic piezoelectric coefficients d _h ⁽ⁱ⁾ of Sn₂P₂S₆ crystals has been studied. The hydrostatic piezoelectric coefficients d _h ⁽¹⁾ and d′ _h ⁽³⁾ , were measured, d _h ⁽¹⁾ =(244±3) pC/N and d′ _h ⁽³⁾ =(92±1) pC/N. The hydrostatic piezoelectric coefficient d _h ⁽³⁾ for orthogonal axis system was calculated to be d _h ⁽³⁾ =(87±2) pC/N. The, optimal orientation of the sample has been found as (Xy l)−20°-cut. Maximal value of the effective hydrostatic piezoelectric coefficient d _h ⁽¹⁾ equals 260 pC/N. Double rotated samples were also studied. The orientation of the samples insensitive to the pressure has been found. The theoretical mean value of hydrostatic piezoelectric coefficient (d _h ) _mean corresponding to randomly oriented Sn₂P₂S₆ grains in a poled composite has been calculated to be (d _h ) _mean =136 pC/N.     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Up-conversion emissions of Er<Superscript>3+</Superscript>-Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles by the arc discharge synthesis method

The Er³⁺-Yb³⁺ codoped Al₂O₃ nanoparticles with an average particle size of about 50 nm have been synthesized by an arc discharge synthesis method. The green and red up-conversion emissions centered at about 526, 547 and 677 nm, corresponding respectively to the ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978-nm semiconductor laser diode excitation. The Annealing has evident effect on the up-conversion emissions of the samples: The red up-conversion emission is noticeable before annealing; however, the green up-conversion emission becomes predominant after annealing. The mixture of (Er,Yb)₃Al₅O₁₂ and α-(Al,Er,Yb)₂O₃ phases is more favorable for green up-conversion emissions due to an enhancement of the ESA (I) of ⁴I_11/2+a photon→⁴F_7/2 and ET (III) of ²F_5/2(Yb³⁺)+⁴I_11/2(Er³⁺)→²F_7/2(Yb³⁺)+⁴F_7/2(Er³⁺) processes. The two-photon absorption up-conversion process is involved in the green and red up-conversion emissions. The results have proved that arc discharge synthesis is a new promising preparation technology for optical materials. Supported by National Natural Science Foundation of China (Grant No. 10804015), the Scientific Research Foundation for Doctor of Liaoning Province (Grant No. 20071095), and the Educational Committee Foundation of Liaoning Province (Grant No. 2008123)     

Theoretical study of ZnO adsorption and bonding on Al<Subscript>2</Subscript>O<Subscript>3</Subscript> (0001) surface

ZnO adsorption on sapphire (0001) surface is theoretically calculated by using a plane wave ultrasoft pseudo-potential method based onab initio molecular dynamics. The results reveal that the surface relaxation in the first layer Al-O is reduced, even eliminated after the surface adsorption of ZnO, and the chemical bonding energy is 434.3(±38.6) kJ · mol⁻¹. The chemical bond of ZnO (0.185 ± 0.01 nm) has a 30° angle away from the adjacent, Al-O bond, and the stable chemical adsorption position of the Zn is deflected from the surface O-hexagonal symmetry with an angle of about 30°. The analysis of the atomic populations, density of state and bonding electronic density before and after the adsorption indicates that the chemical bond formed by the O²⁻ of the ZnO and the surface Al³⁺ has a strong ionic bonding characteristic, while the chemical bond formed by the Zn²⁺ and the surface O²⁻ has an obvious covalent characteristic, which comes mainly from the hybridization of the Zn 4s and the O 2p and partially from that of the Zn 3d and the O 2p.     

VUV luminescence of Er<Superscript>3+</Superscript> ions in LiYF<Subscript>4</Subscript> and BaY<Subscript>2</Subscript>F<Subscript>8</Subscript> crystals

Vacuum ultraviolet luminescence of Er³⁺ ions in LiYF4 and BaY₂F₈ crystals has been investigated. It is revealed that under excitation by 193 nm radiation from an ArF excimer laser the interconfigurational 5d–4f radiative transitions in Er³⁺ ions are observed. It is shown that from the LiYF₄:Er crystal only the spin-forbidden luminescence (λ = 165 nm) is detected, whereas both the spin-forbidden (λ = 169 nm) and spin-allowed (λ = 160.5 nm) components are observed from the BaY₂F₈:Er crystal.     

Structural investigation on PEO-based polymer electrolytes dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

Thin solid polymer electrolytes based on polyethylene oxide (PEO) and silver triflate (AgCF₃SO₃) dispersed with various concentrations of aluminum oxide (Al₂O₃) nanoparticles have been prepared by solution casting technique. These thin polymer films are found to have thickness of the order of 30 to 100 μm. The X-ray diffraction (XRD) patterns have indicated the amorphous nature of the polymer electrolyte. The differential scanning calorimeter (DSC) traces showed slight change in the glass transition temperature (T _g) whereas the degree of crystallization (X _c) decreases markedly due to the addition of alumina nanoparticles. Fourier transform infrared (FTIR) spectral analysis of all these samples has revealed the presence of absorption bands around 1,000 cm⁻¹; thus indicating the complexation of silver ions with oxygen in PEO. Employing the Wagner’s polarization technique as the standard method, the total ionic transference number for the complexed polymer electrolyte was found to be approximately unity thereby revealing that the significant contribution to electrical conduction was due to ions only. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006     

Preparation of nanosized Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript> using different content of starting materials and their photoactivities

A series of nanosized Bi₂WO₆ catalysts was synthesized using various starting materials, and they were characterized by X-ray diffractometry, transmission electron microscopy, and diffuse reflectance spectroscopy. Rhodamine-B (RhB) photodegradation in aqueous medium was employed as a probe reaction to test the photoactivity of the as-prepared samples. Dependence of the photocatalytic activities on different contents of the starting materials was examined under visible irradiation (λ > 400 nm). The sample prepared in the following conditions: reaction time 24 h, the pH of the solution 7, the Bi³⁺ amount in the start precipitates 5 mmol — exhibited the highest photochemical activity when the hydrothermal temperature was settled at 180°C. Published in Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 2, pp. 243–249, Martch–April, 2009.     

Spectral and kinetic characteristics of CdI<Subscript>2</Subscript> and CdI<Subscript>2</Subscript>:Pb scintillators

We have studied the effect of lead dopant on the optical absorption, photoluminescence, and x-ray luminescence spectra, and the scintillation characteristics of CdI₂ at room temperature. The crystals for the study were grown by the Stockbarger-Bridgman method. Activation of CdI₂ from the melt by the compound PbI₂ leads to the appearance in the absorption spectra in the near-edge region of an activator band at 395–405 nm, which is interpreted as an A band connected with electronic transitions from the ¹S₀ state to the ³P₁ levels in the Pb²⁺ ion. For x-ray excitation, CdI₂:Pb²⁺ crystals with optimal dopant concentration (∼1.0 mol%) are characterized by a light yield with maximum in the 570–580 nm region that is an order of magnitude higher than for CdI₂ crystals in the 490–500 nm band. For α excitation, the radioluminescence kinetics for cadmium iodide is characterized by a very short (∼0.3 nsec) rise time and fast decay of luminescence, with τ₁ ≈ 4 nsec and τ₂ = 10–76 nsec. Depending on the conditions under which the crystals were obtained, the fast component fraction is 95%–99%. The crystal is characterized by a similar scintillation pulse in the case of excitation by x-ray pulses. The radioluminescence pulse shape for CdI₂:Pb in the decay stage is predominantly exponential, with luminescence decay time constants τ₁ ≈ 10 nsec and τ₂ = 200–250 nsec. This system is characterized by low afterglow, at the level for the Bi₄G₃O₁₂ scintillator. We have demonstrated the feasibility of using CdI₂:Pb as a scintillator for detecting α particles. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 6, pp. 825–830, November–December, 2008.     

n/p-Type changeable semiconductor TiO<Subscript>2</Subscript> prepared from NTA

A novel kind of nano-sized TiO₂ (anatase) was obtained by high-temperature (400–700°C) dehydration of nanotube titanic acid (H₂Ti₂O₄(OH)₂, NTA). The high-temperature (400–700°C) dehydrated nanotube titanic acids (HD-NTAs) with a unique defect structure exhibited a p-type semiconductor behavior under visible-light irradiation ( nm, E _photon=2.95 eV), whereas exhibited an n-type semiconductor behavior irradiated with UV light ( nm, E _photon=3.40 eV).     

Anti-stokes luminescence of solid AgCl<Subscript>0.95</Subscript>I<Subscript>0.05</Subscript> solutions

An anti-Stokes luminescence band with λ_max = 515 nm of microcrystals of solid AgCl_0.95I_0.05 solutions excited by a radiation flux of density 10¹³–10¹⁵ quanta/cm²·sec in the range 600–800 nm at 77 K was detected. It is shown that the intensity of this luminescence and the frequency of its excitation depend on the prior UV-irradiation of samples. Analysis of the stimulated-photoluminescence spectra and the anti-Stokes luminescence excitation spectra of the indicated microcrystals has shown that to the centers of anti-Stokes luminescence excitation correspond local levels in the forbidden band of the crystals. These states are apparently due to the atomic and molecular disperse silver particles that can be inherent in character or formed as a result of a low-temperature photochemical process. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 72, No. 6, pp. 738–742, November–December, 2005.     

Synthesis of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> complex substrates and growth of GaN films

With the solid phase reaction between pulsed-laser-deposited (PLD) ZnO film and α-Al₂O₃ substrate, ZnAl₂O₄/α-Al₂O₃ complex substrates were synthesized. X-ray diffraction (XRD) spectra show that as the reaction proceeds, ZnAl₂O₄ changes from the initial (111)-oriented single crystal to poly-crystal, and then to inadequate (111) orientation. Corresponding scanning electron microscope (SEM) images indicate that the surface morphology of ZnAl₂O₄ transforms from uniform islands to stick structures, and then to bulgy-line structures. In addition, XRD spectra present that ZnAl₂O₄ prepared at low temperature is unstable at the environment of higher temperature. On the as-obtained ZnAl₂O₄/α-Al₂O₃ substrates, GaN films were grown without any nitride buffer using light-radiation heating low-pressure MOCVD (LRH-LP-MOCVD). XRD spectra indicate that GaN film on this kind of complex substrate changes fromc-axis single crystal to poly-crystal as ZnAl₂O₄ layer is thickened. For the single crystal GaN, its full width at half maximum (FWHM) of X-ray rocking curve is 0.4°. Results indicate that islands on thin ZnAl₂O₄ layer can promote nucleation at initial stage of GaN growth, which leads to the (0001)-oriented GaN film.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Surface morphology of PrBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7-δ</Subscript> single crystals after the long-lasting high-temperature reduction

The results of the detailed scanning electron microscopy study of PrBa₂Cu₃O_7-δ single crystals after the long-lasting high-temperature post-growth treatment are reported. The presence of the unstable decomposition products on the crystal surface indicates that the onset of superconductivity must be related to the structural transformations in the bulk (approximately 20% of the total volume of the examined crystals). The time-dependent character of the superconductivity in the Pr-123 crystals could be attributed to the migration of defects in the Pr−Ba sublattice from the bulk toward the surface.     

Evaluation of nanoparticle emission for TiO<Subscript>2</Subscript> nanopowder coating materials

In this study, nanoparticle emission of TiO₂ nanopowder coated on different substrates including wood, polymer, and tile, was evaluated in a simulation box and measured with a Scanning Mobility Particle Sizer (SMPS) for the first time. The coating process for the substrate followed the instructions given by the supply company. In the simulation box, UV light, a fan, and a rubber knife were used to simulate the sun light, wind, and human contacting conditions. Among the three selected substrates, tile coated with TiO₂ nanopowder was found to have the highest particle emission (22 #/cm³ at 55 nm) due to nanopowder separation during the simulation process. The UV light was shown to increase the release of particle below 200 nm from TiO₂ nanopowder coating materials. The results show that, under the conditions of UV lamps, a fan and scraping motion, particle number concentration or average emission rate decreases significantly after 60 and 90 min for TiO₂/polymer and TiO₂/wood, respectively. However, the emission rate continued to increase after 2 h of testing for TiO₂/tile. It is suggested that nanoparticle emission evaluation is necessary for products with nanopowder coating.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

Optical waveguides in LiNbO<Subscript>3</Subscript> and stoichiometric LiNbO<Subscript>3</Subscript> crystals by proton exchange

The formation of optical planar waveguides in LiNbO₃ and stoichiometric LiNbO₃ crystals by proton exchange was reported. The prism-coupling method was used to characterize the dark-line spectroscopy at the wavelength of 633 and 1539 nm, respectively. The mode optical near-field outputs from proton-exchanged LiNbO₃ and SLN waveguides at 633 nm were presented. The mode field from stoichiometric LiNbO₃ (SLN) waveguide is lighter and more uniform than that from LiNbO₃ waveguide, which means the quality of the waveguide in SLN crystal is better than that of the LiNbO₃ waveguide. For proton-exchanged LiNbO₃ waveguides, the evolution of the refractive index profile with annealing was presented. The disorder profiles of Nb atoms in proton-exchanged LiNbO₃ waveguides were obtained by Rutherford backscattering/channeling technique. It is shown that the longer the exchange time, the larger the displacement of Nb atoms. Supported by the National Natural Science Foundation of China (Grant No. 10475052) and the Scientific Research Start-up Financing of Qufu Normal University     

Accuracy in determination of the temperature and partial pressure of CO<Subscript>2</Subscript> in CO<Subscript>2</Subscript>:N<Subscript>2</Subscript>:H<Subscript>2</Subscript>O:NO<Subscript>2</Subscript> mixtures by multiple-frequency laser probing

We present the results of analysis of the errors introduced by hot-band transitions 11¹0-01¹1, 03¹0-01¹1, 12⁰0-12⁰1 of the CO₂ molecule and the absorption lines of the H₂O and NO₂ molecules in determination of the temperature and partial pressure of CO₂, included in the gas mixture CO₂: N₂:H₂O: NO₂ at atmospheric pressure, by multiple-frequency laser probing using a CO₂ laser tunable over the lines of the 00⁰1-[10⁰0,02⁰0]_I,II ground-state laser transitions. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 6, pp. 810–815, November–December, 2007.     

Absorption by CS<Subscript>2</Subscript> molecules on “hot” band emission lines from a TEA CO<Subscript>2</Subscript> laser

We have measured absorption of emission from a TEA CO₂ laser, lasing on hot band lines, in pure CS₂ and a mixture of CS₂ with air, and we have determined the optimal lines for optical excitation. Numerical modeling has shown that as the peak intensity of the pump radiation is increased, we observe absorption saturation, the extent of which decreases as the pressure increases. The major factor responsible for absorption saturation is the “rotational bottleneck” effect. Depending on the peak intensity of the radiation, addition of a buffer gas can lead to an increase or decrease in the absorption. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 1, pp. 61–66, January–February, 2007.