Preparation of nano-hydroxyapatite/poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactide) biocomposite microspheres

Nano-hydroxyapatite (HA)/poly(l-lactide) (PLLA) composite microspheres with relatively uniform size distribution were prepared by a solid-in-oil-in-water (s/o/w) emusion solvent evaporation method. The encapsulation of the HA nanopaticles in microshperes was significantly improved by grafting PLLA on the surface of the HA nanoparticles (p-HA) during emulsion process. This procedure gave a possibility to obtain p-HA/PLLA composite microspheres with uniform morphology and the encapsulated p-HA nanoparticle loading reached up to 40 wt% (33 wt% of pure HA) in the p-HA/PLLA composite microspheres. The microstructure of composite microspheres from core-shell to single phase changed with the variation of p-HA to PLLA ratios. p-HA/PLLA composite microspheres with the diameter range of 2–3 μm were obtained. The entrapment efficiency of p-HA in microspheres could high up to 90 wt% and that of HA was only 13 wt%. Surface and bulk characterizations of the composite microspheres were performed by measurements such as wide angle X-ray diffraction (WAXD), thermal gravimetric analysis (TGA), environmental scanning electron microscope (ESEM) and transmission electron microscopy (TEM).     

Synthesis of nanoparticles and its effect on properties of elastomeric nanocomposites

Calcium carbonate (CaCO₃) nanoparticles (9, 15, and 21 nm) were synthesized by solution spray of CaCl₂ and NH₄HCO₃ with sodium lauryl sulfate (SLS) as a stabilizing agent, and their effect was studied on polybutadiene rubber (PBR) with variations in wt% loading (4, 8, and 12%). The results of PBR nanocomposites were compared with commercial CaCO₃ (40 μm) and fly ash (75 μm) filled PBR microcomposites. Properties such as tensile strength, young modulus, elongation at break, glass transition temperature, decomposition temperature, and abrasion resistances were determined. Profound effect in properties was observed, because nanometric size of CaCO₃ particles synthesized using solution spray technique. Maximum improvement in mechanical and flame retarding properties was observed at 8 wt% of filler loading. This increment in properties was more pronounced in 9-nm size CaCO₃. The results were not appreciable above 8 wt% of nanofillers because of agglomeration of nanoparticles. In addition, an attempt was made to consider modeling Young’s modulus of PBR–nano CaCO₃ which was predicted by modified Halpin–Tsai equation. It was observed that the predication by the Guth equation and modified Halpin–Tsai equation agreed very well with experimental, whereas the Halpin–Tsai equation can only applied to predict the modulus of rubber nanocomposites in the range of low addition of nanofiller, which agrees the Nielsen equation.     

Controlled oxidation of iron nanoparticles in chemical vapour synthesis

Enteric-coated formulations can delay the release of drugs until they have passed through the stomach. However, high concentration of drugs caused by rapidly released in the small intestine leads to the intestinal damage, and frequent administration would increase the probability of missing medication and reduce the patient compliance. To solve the above-mentioned problems, aspirin-loaded enteric-coated sustained-release nanoparticles with core–shell structure were prepared via one-step method using coaxial electrospray in this study. Eudragit L100-55 as pH-sensitive polymer and Eudragit RS as sustained-release polymer were used for the outer coating and inner core of the nanoparticles, respectively. The maximum loading capacity of nanoparticles was 23.66 % by changing the flow rate ratio of outer/inner solutions, and the entrapment efficiency was nearly 100 %. Nanoparticles with core–shell structure were observed via fluorescence microscope and transmission electron microscope. And pH-sensitive and sustained drug release profiles were observed in the media with different pH values (1.2 and 6.8). In addition, mild cytotoxicity in vitro was detected, and the nanoparticles could be taken up by Caco-2 cells within 1.0 h in cellular uptake study. These results indicate that prepared enteric-coated sustained-release nanoparticles would be a more safety and effective carrier for oral drug delivery.     

Synthesis and characterization of noscapine loaded magnetic polymeric nanoparticles

The delivery of noscapine therapies directly to the site of the tumor would ultimately allow higher concentrations of the drug to be delivered, and prolong circulation time in vivo to enhance the therapeutic outcome of this drug. Therefore, we sought to design magnetic based polymeric nanoparticles for the site directed delivery of noscapine to invasive tumors. We synthesized Fe₃O₄ nanoparticles with an average size of 10±2.5 nm. These Fe₃O₄ NPs were used to prepare noscapine loaded magnetic polymeric nanoparticles (NMNP) with an average size of 252±6.3 nm. Fourier transform infrared (FT-IR) spectroscopy showed the encapsulation of noscapine on the surface of the polymer matrix. The encapsulation of the Fe₃O₄ NPs on the surface of the polymer was confirmed by elemental analysis. We studied the drug loading efficiency of polylactide acid (PLLA) and poly (l-lactide acid-co-gylocolide) (PLGA) polymeric systems of various molecular weights. Our findings revealed that the molecular weight of the polymer plays a crucial role in the capacity of the drug loading on the polymer surface. Using a constant amount of polymer and Fe₃O₄ NPs, both PLLA and PLGA at lower molecule weights showed higher loading efficiencies for the drug on their surfaces.     

Preparation and Thermal Properties of Boron-Containing o-Cresol-Formaldehyde Resin/Octa(aminophenyl)-POSS Nanocomposites

The boron-containing o-cresol-formaldehyde resin (BoCFR) and octa(aminophenyl) polyhedral oligomeric silsesquioxane (OAP-POSS) were synthesized, and the BoCFR/OAP-POSS nanocomposite prepared via an in-situ method. The curing process of the resin was characterized by Fourier transform infrared (FTIR). The thermal properties and dynamic mechanical properties of the nanocomposites were investigated. The results show that the maximal mechanical loss temperature (T_p) increased with increasing OAP-POSS content. When the content of OAP-POSS was 10 wt% the T_p was over 200°C, 27°C higher than the pure BoCFR. The BoCFR/OAP-POSS nanocomposite had better thermal stablitity than the pure BoCFR. The residual weight of the o-cresol-formaldehyde resin was only 6.13 wt% at 600°C. But the residual weight of the pure BoCFR was 55.73 wt% at 600°C, and the residual weights of the BoCFR nanocomposites were all higher than pure BoCFR. The residual weight of the BoCFR nanocomposite was 63.2 wt% at 600°C and 21.83 wt% at 900°C when the OAP-POSS content was 10 wt%. The weight loss of BoCFR/OAP-POSS nanocomposite can be divided primarily into two temperature stages, from 430°C to 550°C and from 550°C to 900°C. The main thermal degradation reaction follows first order kinetics.     

Rapid synthesis of SiO<Subscript>2</Subscript> by ultrasonic-assisted Stober method as controlled and pH-sensitive drug delivery

In this paper, the monodisperse silica nanoparticles were prepared by ultrasonic-assisted Stober method, and it explained that the ultrasonic cavitation effect shortened the reaction time from the original hours to f5 min. The effects of ultrasonic time, ultrasonic power, and stirring speed on the morphology, composition, and specific surface area of silica nanoparticles were investigated by field emission electron microscopy (FE-SEM). The results showed that nanoparticles with the best dispersity and the most uniform morphology were obtained under the optimized conditions (ultrasonic time is 5 min, ultrasonic power is 160 W, and the magnetic stirring speed is 999 rpm). The phase composition of SiO₂ was characterized by high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), nano-size/zeta potential analyzer, and Fourier transform infrared spectroscopy (FT-IR). It showed that all typical peaks of samples are in line with the SiO₂ spectrum, the particle size distribution and zeta potential value of the silica is 615?±?35.6 nm and 59.87?±?0.91 mv, respectively, which further verified that the spherical silica nanoparticles with good dispersity can be synthesized in a very short time. Hemolysis test showed that nano-SiO₂ had high blood compatibility and biocompatibility when its concentration was less than 1 mg/mL. Doxorubicin (DOX·HCl) was regarded as a drug model to investigate the drug loading capacity of synthesized SiO₂; the results showed that the drug loading capacity and encapsulation efficiency reached 42.6?±?1.2 and 85.2?±?2.5%, respectively. Furthermore, the drug release experiments fitted well with the Higuichi equation with correlation coefficient (R²) of 0.9984, which further confirmed that the SiO₂/DOX drug delivery system has the controlled release property, and it also displayed pH-responsive behavior (at 96 h, the cumulative release of SiO₂/DOX in PBS solution with pH 7.4, 6.5, and 5.0 was 48.33, 62.31, and 94.86%, respectively). Therefore, this paper provides the possibility for developing more effective, safer, and more targeted controlled drug carriers.     

Synthesis of plate-like Li<Subscript>3</Subscript>PS<Subscript>4</Subscript> solid electrolyte via liquid-phase shaking for all-solid-state lithium batteries

The precursor of plate-like Li₃PS₄ solid electrolyte (75Li₂S?25P₂S₅, SE (LS)), about 3 μm in length, 500 nm in width, and 100–200 nm in thickness, was successfully prepared from Li₂S and P₂S₅ using ethyl propionate (EP) as a synthetic medium via liquid-phase shaking. Upon evacuating at 170 °C, the precursor decomposed to SE (LS), which exhibited ionic conductivity of about 2.0 × 10^?4 Scm^?1 at room temperature. SEM observation revealed that the SE (LS) thus obtained had plate-like morphology with dimension of 3 μm in length, 500 nm in width, and 100–200 nm in thickness. Owing to the nanosized SE (LS), an all-solid-state half-cell using composite anode consisting of 90 wt% LiNi_1/3Mn_1/3Co_1/3O₂ (NMC) and 10 wt% SE (LS) delivered a high capacity up to 130 mAhg^?1(NMC) at the first discharge.     

Preparation of SnO2–graphene from SnS–graphene oxide for enhanced reversible lithium ion storage

SnO₂–graphene nanocomposites (SnO₂–GNS) have been prepared through a simple hydrothermal reaction with SnS–graphene oxide composites as the precursor. The composite material as prepared was characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, Brunauer–Emmett–Teller analysis, and thermogravimetric analysis. The results indicate that SnO₂ nanoparticles possess a good dispersion on the surface of graphene. Electrochemical tests demonstrate the high reversible lithium ion storage properties of SnO₂–GNS. The nanocomposites retained a reversible capacity of 503 mAh?g^?1 after 40 cycles. Moreover, the composite material exhibited higher capacity and better cyclic performance compared to free SnO₂ nanoparticles physically mixed with graphene in the relative weight ratio. The results suggest that the combination of SnO₂ and graphene leads to synergistic performance, which enhances lithium ion storage properties of the overall system.     

Electrochemical and structural properties of a polymer electrolyte system based on the effect of CeO<Subscript>2</Subscript> nanofiller with PVDF-co-HFP for energy storage devices

In the present work, a series of five different nanocomposite polymer electrolytes (NCPEs) have been reported with varying contents of ceria, CeO₂ nanofiller suitably incorporated within an optimized composition having 75:25 wt% ratio of poly(vinylidenefluoride-co-hexafluoropropylene) [(PVDF-co-HFP)] and zinc trifluoromethanesulfonate (ZnTf) in the form of films obtained by mean of solution casting technique with a general formula [75 wt% PVDF-co-HFP:25 wt% ZnTf]-x wt% CeO₂ where x = 1, 3, 5, 7, and 10, respectively. The chosen NCPE system is found to exhibit the maximum electrical conductivity of 3 × 10^?4 S cm^?1 for 5 wt% loading of CeO₂ nanofiller at ambient temperature. The observed conductivity enhancement has been attributed to the occurrence of an increase in the amorphous content as confirmed by X-ray diffraction (XRD) analysis. Detailed Fourier transform infrared (FTIR) spectral analysis has indicated the feasibility of complexation of the host polymer matrix with ZnTf salt and CeO₂ nanofiller. The incorporation of CeO₂ nanofiller has further increased the decomposition voltage of the polymer electrolyte from 2.4 to 2.7 V as revealed from the voltammetric studies performed on such NCPEs, thereby suggesting the suitability of these NCPE films with an enhanced electrical conductivity as new electrolytes in order to design and fabricate eco-friendly zinc rechargeable batteries and other electrochemical devices.     

Effects of Gd<Superscript>3+</Superscript> modifications on the photoelectrochemical properties of TiO<Subscript>2</Subscript>-based dye-sensitized solar cells

In this paper, TiO₂ particles (~30 nm) modified with Gd₂O₃-coating layer (~2 nm) for dye-sensitized solar cells (DSSCs) were fabricated via the hydrothermal method. Among the solar cells based on the Gd³⁺-doped TiO₂ photoanodes, the optimal conversion efficiency was obtained from the 0.025Gd³⁺-modified TiO₂-based cell, with a 17.7% improvement in the efficiency as compared to the unmodified one (7.18%). This enhancement was probably due to the improved UV radiation harvesting via a down-conversion luminescence process by Gd³⁺ ions, enhancement of visible light absorption and improved dye loading capacity. In addition, after Gd modification, a thin coating could be formed on the TiO₂ nanoparticles, which worked as an energy barrier and resulted in a lower charge recombination.     

Microwave-assisted rapid synthesis of tetragonal Cu2SnS3 nanoparticles for solar photovoltaics

A simple and rapid process for the synthesis of Cu₂SnS₃ (CTS) nanoparticles by microwave heating of metal–organic precursor solution is described. X-ray diffraction and Raman spectroscopy confirm the formation of tetragonal CTS. X-ray photoelectron spectroscopy indicates the presence of Cu, Sn, S in +1, +4, ?2 oxidation states, respectively. Transmission electron microscopy divulges the formation of crystalline tetragonal CTS nanoparticles with sizes ranging 2–25 nm. Diffuse reflectance spectroscopy in the 300–2,400 nm wavelength range suggests a band gap of 1.1 eV. Pellets of CTS nanoparticles show p-type conduction and the carrier transport in temperature range of 250–425 K is thermally activated with activation energy of 0.16 eV. Thin film solar cell (TFSC) with architecture: graphite/Cu₂SnS₃/ZnO/ITO/SLG is fabricated by drop-casting dispersion of CTS nanoparticles which delivered a power conversion efficiency of 0.135 % with open circuit voltage, short circuit current and fill factor of 220 mV, 1.54 mA cm^?2, 0.40, respectively.     

Bonding at Compatible and Incompatible Amorphous Interfaces of Polystyrene and Poly(Methyl Methacrylate) Below the Glass Transition Temperature

Abstract

Films of high‐molecular‐weight amorphous polystyrene (PS, M _w = 225 kg/mol, M _w/M _n = 3, T _g‐bulk = 97°C, where T _g‐bulk is the glass transition temperature of the bulk sample) and poly(methyl methacrylate) (PMMA, M _w = 87 kg/mol, M _w/M _n = 2, T _g‐bulk = 109°C) were brought into contact in a lap‐shear joint geometry at a constant healing temperature T _h, between 44°C and 114°C, for 1 or 24 hr and submitted to tensile loading on an Instron tester at ambient temperature. The development of the lap‐shear strength σ at an incompatible PS–PMMA interface has been followed in regard to those at compatible PS–PS and PMMA–PMMA interfaces. The values of strength for the incompatible PS–PMMA and compatible PMMA–PMMA interfaces were found to be close, both being smaller by a factor of 2 to 3 than the values of σ for the PS–PS interface developed after healing at the same conditions. This observation suggests that the development of the interfacial structure at the PS–PMMA interface is controlled by the slow component, i.e., PMMA. Bonding at the three interfaces investigated was mechanically detected after healing for 24 hr at T _h = 44°C, i.e., well below T _g‐bulks of PS and PMMA, with the observation of very close values of the lap‐shear strength for the three interfaces considered, 0.11–0.13 MPa. This result indicates that the incompatibility between the chain segments of PS and PMMA plays a negligible negative role in the interfacial bonding well below T _g‐bulk.     

Green electrolytes based on dextran-chitosan blend and the effect of NH<Subscript>4</Subscript>SCN as proton provider on the electrical response studies

Dextran-chitosan blend added with ammonium thiocyanate (NH₄SCN)-based solid polymer electrolytes are prepared by solution cast method. The interaction between the components of the electrolyte is verified by Fourier transform infrared (FTIR) analysis. The blend of 40 wt% dextran-60 wt% chitosan is found to be the most amorphous ratio. The room temperature conductivity of undoped 40 wt% dextran-60 wt% chitosan blend film is identified to be (3.84?±?0.97)?×?10^?10 S cm^?1. The inclusion of 40 wt.% NH₄SCN to the polymer blend has optimized the room temperature conductivity up (1.28?±?0.43)?×?10^?4 S cm^?1. Result from X-ray diffraction (XRD) and differential scanning calorimetry (DSC) analysis shows that the electrolyte with the highest conductivity value has the lowest degree of crystallinity (χ _c) and the glass transition temperature (T _g), respectively. Temperature-dependence of conductivity follows Arrhenius theory. From transport analysis, the conductivity is noticed to be influenced by the mobility (μ) and number density (n) of ions. Conductivity trend is further verified by field emission scanning electron microscopy (FESEM) and dielectric results.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanofiller on the electrical,thermal and structural properties of PEO:PPG based nanocomposite polymer electrolyte

A new series of nanocomposite polymer electrolyte (NCPE) system comprising of polyethylene oxide (PEO) and polypropylene glycol (PPG) as blended polymer host, zinc trifluoromethanesulfonate [Zn(CF₃SO₃)₂] as dopant salt and nanocrystalline alumina [Al₂O₃] as filler was prepared by solution casting technique. The present system consisting of five different compositions of 87.5 wt% (PEO:PPG)–12.5 wt% Zn(CF₃SO₃)₂ + x wt% Al₂O₃ [where x = 1, 3, 5, 7 and 9, respectively] has been thoroughly characterized by various analytical techniques such as electrical impedance spectroscopy, X-ray diffraction (XRD) studies, differential scanning calorimetry (DSC), scanning electron microscopic (SEM) analysis and linear sweep voltammetry (LSV). The maximum room temperature ionic conductivity exhibited by the NCPE was found to be 2.1 × 10^?4 S cm^?1 for 3 wt% loading of Al₂O₃ which is an order higher than that of the optimized filler-free zinc salt doped polymer electrolyte system at 298 K. The evidence of a decrease in the degree of crystallinity responsible for the enhanced conductivity was revealed by the XRD data and further confirmed by DSC and SEM results. Moreover, the electrochemical stability window of the highly conducting electrolyte matrix has been experimentally determined by linear sweep voltammetry and found to be 3.6 V which is fairly adequate for the construction of zinc primary batteries as well as zinc-based rechargeable batteries at ambient conditions.     

Effect of H<Subscript>3</Subscript>PO<Subscript>2</Subscript> on the mechanical,thermal, and electrical properties of polymers based on poly (vinyl alcohol) (PVA) and chitosan (CS)

A polymer based on poly (vinyl alcohol) (PVA) and chitosan (CS) with a weight ratio of 80:20 was prepared by solvent casting processes, and the effect of H₃PO₂ was investigated. Thermal analysis shows miscibility of the two polymer amorphous phases since a single T_g was located between those of the individual components and the melting point of the crystalline phase was depressed to 189 °C. It was found that the acid acts as a plasticizer for the PVA-CS blends and its T_g is depressed significantly to 23 °C as the acid concentration increases to 50%. Strain-stress tests also corroborate this effect. The DC conductivity of the blends follows an Arrhenius-type thermal activation behavior with activation energy of 0.1 eV in the 30–90 °C temperature range. Moreover, the conductivity increases with increasing acid content up to a maximum value of approximately 1.4 × 10^?2 S/cm for the blend with an acid concentration of 50%.     

Thermal Performance of a Blend System Based on Poly(l-lactic acid) and an Aliphatic Multiamide Derivative of 1H-Benzotriazole

An aliphatic multiamide derivative derived from 1H-benzotriazole, N, N'-bis(1H-benzotriazole) sebacic acid acethydrazide (SA), was synthesized to evaluate its effect on the thermal performance, including non-isothermal crystallization and melting behavior as well as thermal stability, of poly(l-lactic acid) (PLLA). The comparative study, by means of DSC measurements, showed that the incorporation of SA caused a non-isothermal crystallization peak to appear and become sharp, showing its advanced crystallization promoting effect for PLLA. The non-isothermal crystallization results further indicated that 2 wt% SA was the saturation concentration for PLLA crystallization, and that the cooling rate was also a crucial determinant for PLLA crystallization. Considering the melting behavior, the difference between the virgin PLLA and PLLA/2%SA further confirmed the crystallization accelerative effect of SA for PLLA, with the increase of crystallization temperature in the temperature zone from 90 to 130°C being beneficial to the crystallization of PLLA during processing. Compared to the virgin PLLA, the trends of thermal decomposition curves were similar, suggesting that the introduction of SA of 0.5–3 wt% did not significantly change the thermal decomposition behavior of PLLA.     

Influence of K<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> on dielectric and barrier properties of polymer

Polymer composite comprising polyvinylidene fluoride (PVDF) and potassium hexatitante (K₂Ti₆O₁₃) was synthesized by solution casting. The effect of K₂Ti₆O₁₃ on surface, thermal, and electrical properties of polymer composite were investigated. The addition of K₂Ti₆O₁₃ with polymer leads to thermal degradation and transition of polymer composite from semi-crystalline to amorphous phase. The optimum results of contact angle for different loading wt% of K₂Ti₆O₁₃ were directly correlated with the surface morphology. Our experimental results confirmed the incorporation of K₂Ti₆O₁₃ in polymer by SEM micrographs. The evaluated dielectric properties (ε' = 424; tan δ = 2.14 at 130 °C and 100 Hz frequency for 20 wt% loading of K₂Ti₆O₁₃) for polymer composite are higher in compared to pure polymer. The enhancement in dielectric constant and changing the surface properties of polymer composite can be used for the development of electrochemical storage device applications.     

II–VI and II1−x Mn x VI semiconductor nanocrystals formed by the pressure cycle method

II–VI and II_1?x Mn _x VI nanocrystals were prepared by the pressure cycle method using the Paris–Edinburgh cell. The recovered samples are nanocrystals in the cubic phase zinc-blend (ZB) structure and were characterized using transmission electron microscopy, electron diffraction, X-ray diffraction and Raman scattering. Transmission electron micrographs show that these nanocrystals are nearly spherical with diameters ranging from 20 to 50 nm depending on the sample under investigation. The Raman scattering measurements confirm the existence of II–VI nanocrystals in the cubic phase (ZB). The magnetic properties of Cd_0.5Mn_0.5Te nanoparticles were found to vary with the particle size and were different from those observed for the Cd_0.5Mn_0.5Te bulk initial samples. The χ vs. T data show temperature hysteresis due to spin-glass form, which occurs at T _g=21 K, for both the bulk as well as for the recovered nanoparticle samples. The zero-field cooled and field-cooled χ vs. T curves for the nanoparticles showed a monotonous increase below T _g. Below ～21 K, the M vs. B curve for the recovered nanoparticle samples exhibited magnetic hysteresis, and this is attributed to a weak ferromagnetic contribution. This contribution is also observed in the χ(T) curves and is due to a large surface/volume ratio of the nanoparticles, which enhances the magnetic interaction.     

Cu-supported carbon networks containing SnO<Subscript>2</Subscript> as three-dimensional anodes for lithium-ion batteries

Cu-supported SnO₂@C composite coatings constructed by interconnected carbon-based porous branches were fabricated by annealing Cu foils with films formed by knife coating DMF solution containing SnCl₂, polyacrylonitrile (PAN), and poly(methyl methacrylate) (PMMA) on their surface in vacuum. The carbon-based porous branches consist of amorphous carbon matrices, SnO₂ nanoparticles with a size of 30–100 nm mainly encapsulated inside, and many micropores with a size of 1–5 nm. The three-dimensional (3D) porous network structures of the SnO₂@C composite were achieved by volatilization of PMMA and pyrolysis of SnCl₂. The SnO₂@C composite coatings demonstrate good cyclic performance with a high reversible capacity of 642 mA h g^?1 after 100 cycles at a current density of 50 mA g^?1 without apparent capacity fading during cycling and excellent rate performance with a capacity of 276 mA h g^?1 at a high current density up to 10 A g^?1.     

Effect of Temperature on the Composition and Properties of Poly[(alkylamino)borazine] Precursor to Boron Nitride

A novel poly[(alkylamino)borazine] (PPAB) precursor to boron nitride (BN) was synthesized and the effect of synthesis temperature (T_syn) on its composition and properties was investigated. The results showed that with elevation of temperature, the precursor turned from a colorless transparent liquid to a yellow foamed solid. The softening point (T_s) can be adjusted according to the equation T_s = 1.43T_syn – 125.7, in which the T_syn was between 130°C and 170°C. The PPAB was composed of B, C, N, and H elements and the C content in PPAB decreased gradually with an increase of T_syn. The soluble and fusible precursor, with a softening point of 95°C, provided good processability into polymer fibers. The weight loss of PPAB in N₂ can be divided into three ranges: below 240°C, 240～700°C, and 700～1200°C. The ceramic yield of PPAB was improved from 43 wt% to 55 wt%, when the T_syn was elevated from 110°C to 190°C. Furthermore, the residue from PPAB pyrolyzed under N₂ showed characteristic IR spectra of hexagonal BN.