等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

疏水缔合型增稠剂聚(丙烯酰胺-丙烯酸高级酯)的合成及增稠性能研究

采用沉淀聚合法合成了聚（丙烯酰胺－丙烯酸十四酯），聚（丙烯酰胺－丙烯酸十六酯）和聚（丙烯酰胺－丙烯酸十八酯），重点讨论了共聚物中疏水基团数量及疏水基团链长对增稠性能的影响。采用凯达尔定氮法和动态热分析（DMTA）测定了共聚物的组成及玻璃化温度。     

Polymers used as viscosity index improvers: A comparative study

Ethylene-propylene copolymers and hydrogenated styrene-diene copolymers were used for a comparative study aiming at their application as viscosity index improvers in multigrade engine oils. The variation of viscosity with temperature has been evaluated as a function of the polymer concentrations. The thickening effect of different viscosity index improvers and the dependence of reduced viscosities on temperature were determined. At concentrations lower than 3% (w/w) the viscosity/temperature characteristic suggested the occurrence of polymer coil expansion with temperature for hydrogenated styrene-diene copolymer. The direct dependence of mechanical stability on the copolymer molecular weight was observed.     

AA-AM-AN三元共聚物的合成及其溶液性能的研究

采用自由基水溶液共聚法制备了水溶性丙烯酸－丙烯酰胺－丙烯腈共聚物。对聚合反应温度、引发剂用量、尿素用量、聚合物浓度、电解质浓度、剪切速率、温度等因素对聚合物溶液性能的影响进行了研究。结果表明,合成的水溶性聚合物具有良好的增稠作用及耐温抗盐抗剪切等性能。     

Novel approach to synthesizing hydrophobically associating copolymer using template copolymerization: the synthesis and behaviors of acrylamide and 4-(omega-propenoyloxyethoxy) benzoic acid copolymer

Hydrophobically associating copolymers of acrylamide (AM) with a small amount of 4-(omega-propenoyloxyethoxy) benzoic acid (PEBA, <2.5%) were synthesized by template copolymerization in the presence of poly(allylammonium chloride) (PAAC) as a template in an aqueous medium. These template copolymers exhibited remarkable thickening properties due to the effective hydrophobic association, which were similar to those copolymers with a multiblock structure obtained by the micellar process. The pH of the reaction medium and the molecular weight of the template strongly influenced the thickening properties of the products. In the experimental range, the higher the PEBA content, the larger the thickening capacity of these hydrophobic copolymers. The aggregate behaviors of these copolymers were studied by fluorescence, transmission electron microscopy (TEM), and light scattering techniques. The apparent critical interpolymer aggregate concentration (cac) of the copolymer solution was about 0.5 g/dL. As the concentration of the copolymer became higher than the cac, the aggregates changed their morphology from small hollow spheres to big flower-shaped aggregates. All the above results indicated that the template copolymerization gave access to a very simple and powerful means for the preparation of hydrophobically associating copolymers and other functional polymer materials.     

Structural analysis of PEO-PBO copolymer monolayers at the air-water interface

X-ray reflectivity (XR) and grazing incidence X-ray diffraction (GIXD) have been used to examine an oxyethylene-b-oxybutylene (E(23)B(8)) copolymer film at the air-water interface. The XR data were fitted using both a one- and a two-layer model that outputted the film thickness, roughness, and electron density. The best fit to the experimental data was obtained using a two-layer model (representing the oxyethylene and oxybutylene blocks, respectively), which showed a rapid thickening of the copolymer film at pressures above 7 mN/m. The large roughness values found indicate a significant degree of intermixing between the blocks and back up the GIXD data, which showed no long range lateral ordering within the layer. It was found from the electron density model results that there is a large film densification at 7 mN/m, possibly suggesting conformational changes within the film, even though no such change occurs on the pressure-area isotherm at the same surface pressure.     

磺酸基甜菜碱共聚物的合成及其界面活性研究

以N-[3-(二甲氨基)丙基]丙烯酰胺与1,3-丙磺酸内酯为原料,制备了3-[(3-丙烯酰胺)丙基-二甲氨基]丙磺酸钠甜菜碱型单体,并将其与丙烯基聚乙二醇通过自由基聚合物反应合成了磺酸基甜菜碱和聚乙二醇的共聚物.利用红外光谱(FT-IR)和凝胶渗透色谱仪(GPC)对共聚物进行表征,并考察了在高浓度CaCl2条件下该共聚...     

基于棒状介孔SiO_2剪切增稠流体的流变行为

以三嵌段共聚物聚氧乙烯-聚氧丙烯-聚氧乙烯(PEO-PPO-PEO,P123)为模板剂,采用溶胶-凝胶法合成了介孔SiO_2-P123复合物,经煅烧除去P123得到不同长径比的棒状介孔SiO_2粒子,将其分散于聚乙二醇(PEG)中制成剪切增稠流体(STF),利用旋转流变仪对STF的流变性能进行了表征。结果表明:在稳态条件下,STF的剪切增稠效应随介孔SiO_2质量分数的增加而增强,随介孔SiO_2粒子长径比的增加而减弱;在动态条件下,STF的剪切增稠效应随介孔SiO_2质量分数的增加而减弱,随介孔SiO_2粒子长径比的增加而增强。     

Synthesis, rapid responsive thickening, and self-assembly of brush copolymer poly(ethylene oxide)-graft-poly(N,N-dimethylaminoethyl methacrylate) in aqueous solutions

Double hydrophilic brush copolymer poly(ethylene oxide)-graft-poly(N,N-dimethylaminoethyl methacrylate) (PEO-g-PDMAEMA) was successfully prepared via atom transfer radical polymerization (ATRP). We investigated the pH/thermoresponsive behaviors of PEO-g-PDMAEMA brush-shaped copolymer concentrated aqueous solutions by rheology. The observed LCST strongly decreased with increasing pH of the solutions, which was lower than that of linear block copolymer for different pH, indicating rapid thermoresponsiveness of the brush PDMAEMA chains. An unexpected shear thickening behavior was observed and could be tuned by the pH, resulting from the mobile nature and tractive force of the densely grafted hydrophobic chains of PDMAEMA at high pH. Self-assembly of the brush copolymer in a different pH and ionic strength environment was studied by transmission electron microscopy. A wormlike cylinder structure was formed at low pH. Fractals were observed for the brush copolymer aqueous solution in the presence of NaCl. The results showed that by adjusting the pH and NaCl concentration of the dispersions fractal aggregates with different topology were obtained. The observations reported here can supply a better understanding of the molecular self-assembling nature and be used to develop responsive materials with better performance.     

高分子表面活性剂P(AM-co-OPMA)的合成与表征

辛基酚聚氧乙烯醚(10)(OP-10)与马来酸酐在95℃下反应,合成了辛基酚聚氧乙烯醚马来酸单酯(OPMA);并在水溶液中与丙烯酰胺(AM)单体进行共聚合,获得了高分子表面活性剂P(AM-co-OPMA);考察了引发剂用量、单体组成、单体总浓度及反应温度对共聚物特性粘数与阴离子度的影响.通过红外光谱、紫外光谱、荧光发射光谱和电导滴定对共聚物结构和组成进行了表征;利用视频光学接触角测量仪分别测定了共聚物表面和界面张力.结果表明,在聚丙烯酰胺分子主链上引入OPMA链节后,不仅保持了PAM优良的增稠能力(特性粘数达764.31 mL/g),且赋予了共聚物较高的表面活性(浓度为1.5 g/L共聚物水溶液的表面和界面张力分别可达53.94 mN/m和5.41 mN/m).     

丙烯酰胺-苯乙烯双亲嵌段共聚物水溶液的粘度性能

通过改变丙烯酰胺 (AM)与苯乙烯 (St)两单体的投料比 ,在微乳液介质中制备了分子组成系列变化的丙烯酰胺 苯乙烯双亲嵌段共聚物 (PAM b PSt) ,使用旋转粘度计测定了共聚物水溶液的表观粘度 ,详细考察了共聚物浓度、共聚物链结构、剪切速率、盐度及温度等因素对共聚物水溶液表观粘度的影响规律 .研究结果表明 ,由于PAM b PSt分子链中的PSt疏水嵌段链段之间具有强的疏水缔合作用 ,导致其具有独特的流变性能 .当共聚物水溶液的浓度高于某一临界值后 ,疏水缔合作用以分子间的缔合为主 ,大分子链之间会形成动态物理交联网络 ,增大了流体力学体积 ,使PAM b PSt水溶液可产生良好的增稠性能 ;疏水缔合作用是一吸热过程 ,升高温度有利于分子间的缔合 ,因此PAM b PSt水溶液具有良好的耐温性 ;聚合物水溶液中盐类物质的存在 ,会增强溶剂的极性 ,有利于分子间的缔合 ,使PAM b PSt水溶液具有良好的耐盐性 .