SSC-LINAC中APF型DTL的优化设计

A linear accelerator as a new injector for the SSC （Separated Sector Cyclotron） of the HIRFL （Heavy Ion Research Facility Lanzhou） is being designed. The DTL （Drift-Tube-Linac） has been designed to accelerate ^238U^34＋ from 0.140 MeV/u to 0.97 MeV/u. To the first accelerating tank which accelerates ^238U^34＋ to 0.54 MeV/u, the approach of Alternating-Phase-Focusing （APF） is applied. The phase array is obtained by coupling optimization software Dakota and beam optics code LINREV. With the hybrid of Multi- objective Genetic Algorithm （MOGA） and a pattern search method, an optimum array of asynchronous phases is determined. The final growth, both transversely and longitudinally, can meet the design requirements. In this paper, the deign optimization of the APF DTL is presented.     

医用质子直线加速器的设计研究

讨论用于治癌的低束流高能量质子直线加速器的初步物理设计.采用短脉冲和高重复频率的S波段的加速结构,类似于医用电子直线加速器.总长26m,由离子源、RFQ、DTL、SCDTL及SCL组成,能量经70—200MeV有八档可调,平均束流强度10—40nA.     

Thermal analysis of DTL in the SSC-LINAC

A linear accelerator as a new injector for the Separated Sector Cyclotron at the Heavy Ion Research Facility of LAN Zhou is being designed. The Drift-Tube-Linac (DTL) has been designed to accelerate ²³⁸U³⁴⁺ from 0.140 MeV/u to 0.97 MeV/u [1]. The 3D finite element analysis of thermal behavior is presented in this paper. During operation, the cavity will produce Joule heat. The cavity will not work normally due to the high temperature and thermal deformation will lead to frequency drift. So it is necessary to perform thermal analysis to ensure the correct working temperature is used. The result of the analysis shows that after the water cooling system is put into the cavity the temperature rise is about 20 degrees and the frequency drift is about 0.15%.     

A new tuning procedure for the DTL RF field pattern

The DTL tank is a multi-cell cavity.In a fabricated tank,the measured average axial field E0 for each cell may obviously deviate from the designed value.It is generally thought the deviation is due to the errors in fabrication and assembly.But it is not always true.In this paper,it is shown that the deviation may already exist before fabrication in some cases.It is partly due to the imperfection of the current design procedures.A new design method is introduced to reduce the deviation in the design stage.     

中国散裂中子源直线加速器丝靶扫描器的设计与模拟

In this paper, we report the design and simulation of a wire scanner for the linac of the CSNS （China Spallation Neutron Source）. The wire scanner is used to measure the transverse beam profile and the emittance. The effect of beam energy change upon the mechanical design of the wire scanner must be considered. The simulation results of heat on the two specified wires, tungsten and carbon, by using the finite element method software, ANSYS, are presented. In addition, the effect of wire deformation on the beam profile measurement is qualitatively analyzed, and the signal level of the wire scanner is discussed.     

Design and simulation of a wire scanner for the CSNS linac

In this paper,we report the design and simulation of a wire scanner for the linac of the CSNS(China Spallation Neutron Source).The wire scanner is used to measure the transverse beam profile andthe emittance.The effect of beam energy change upon the mechanical design of the wire scanner must beconsidered.The simulation results of heat on the two specified wires,tungsten and carbon,by using the finite element method software,ANSYS,are presented.In addition,the effect of wire deformation on the beam profile measurement is qualitatively analyzed,and the signal level of the wire scanner is discussed.     

高效率行波管电子枪设计及其优化

利用综合迭代法初步确定了用于高效率行波管的电子枪几何尺寸参数,考虑电子枪设计对导流系数、注腰半径、层流性等参数提出的要求,通过建立评价电子注性能优劣的目标函数以量化设计结果;应用EGUN软件和步长加速直接求优的方法对目标函数进行了优化,优化结果满足了设计要求。该电子枪已经用于制管实验,电子注静态通过率99.7%,动态通过率98.0%,电子效率达到34%,实验结果进一步验证了该电子枪设计的合理性。     

NSRL-200MeV直线加速器能谱分析系统的设计

200MeV直线加速器能谱分析系统用来测量直线加速器的束流能谱,为指导直线加速器的调机和了解机器状态提供实验证据。为了克服非成像系统以及分辨率不高的缺点,在NSRL二期工程中对这个系统进行了重新设计,现已安装和调试。叙述了该系统详细的物理设计以及最新的初步实验结果。     

多目标粒子群优化算法在交变相位聚焦直线加速器模拟中的应用

现代智能优化算法粒子群算法\,(Particle Swarm Optimization)\,在加速器设计优化上的应用逐渐增多。交变相位聚焦直线加速器\,(Alternative Phase Focused Drift Tube Linac)\,具有节省空间和造价的优点。将交变相位聚焦直线加速器的初步设计方案作为种子,植入粒子群算法中;以加速器的传输效率和束流能量作为目标,得到该方案的Pareto最优解集;在粒子进化过程中,以前沿解集作为粒子的运动方向,以前沿解集的束流径迹作为粒子的参数来源。最终得到了满足能量增益的高传输效率、大接受度的优化方案。The Particle Swarm Optimization(PSO), one of the modern intelligent optimization algorithms,is increasingly employed in the design and optimization of accelerators. Alternative Phase Focused Drift Tube Linac(APF DTL) has an advantage in cost-effecient fabrication and reduced construction space. The preliminary design of APF DTL is involved in the optimization as the anchor; by taking the acceleration efficiency and the beam energy as two fitness functions, the Pareto optimal set is obtained; the evolutionary direction is determined by the Pareto optimal set and the particles’ parameters in the optimization are derived from the simulations of the randomly selected Pareto optimal solutions. A final optimized design with extracted energy of 5.35 MeV/uand acceleration efficiency greater than 83% is acquired.     

Design of multilayer high-dispersion mirrors using multi-swarm optimization method

Design of high-dispersion mirrors (HDMs) using a proposed multi-swarm optimization method is reported. We design HDMs for Yb:YAG disk oscillator at 1030 nm and ultrashort pulse Cr:YAG laser at 1550 nm. The results show that the optimum group delay dispersion and reflectance can be obtained with optimal number of layers. The proposed optimization method has a fast convergence rate and powerful global search ability and can be utilized effectively for the design of a variety of optical thin film filters.     

NSRL-200MeV直线加速器能谱分析系统的设计

 200MeV直线加速器能谱分析系统用来测量直线加速器的束流能谱，为指导直线加速器的调机和了解机器状态提供实验证据。为了克服非成像系统以及分辨率不高的缺点，在NSRL二期工程中对这个系统进行了重新设计，现已安装和调试。叙述了该系统详细的物理设计以及最新的初步实验结果。     

Design of metaporous supercells by genetic algorithm for absorption optimization on a wide frequency band

The optimization of acoustic absorption by metaporous materials made of complex unit cells with 2D resonant inclusions is realized using genetic algorithm. A nearly total absorption over a wide frequency band can be obtained for thin structures, even for frequencies below the quarter wavelength resonances i.e., in a sub-wavelength regime. The high absorption performances of this material are due to the interplay of usual visco-thermal losses, local resonances and trapped modes. The density of resonant and trapped modes in this dissipative porous layer, is a key parameter for broadband absorption. The best configurations and critical coupling conditions are found by genetic algorithm optimization. Several types of resonators are included gradually in the studied configurations (split-rings, Helmholtz resonators, back cavities) with increasing complexity. The optimization leads to a metaporous structure with a 2-cm sub-wavelength layer thickness, exhibiting a nearly total absorption between 1800 Hz and 7000 Hz. The influence of the incidence angle on the absorption properties is also shown.     

基于单纯形优化法的准方波脉冲形成网络设计

脉冲形成网络常用于大功率固态调制器、微波驱动源以及激光激励源中,以便获取宽平顶的高压长脉冲输出。针对常用的雷利网络,根据宽平顶低纹波的应用需求,开展了优化设计技术研究,提出了基于单纯形优化法的设计算法。主要针对两种情形进行了优化设计及计算：一是电容值相等,通过优化电感值以获取最优的输出波形;二是约定电容值（电容值不完全相等）,通过优化计算不同电容排列下的输出结果,寻求最优的电容排列组合及相应的优化电感值。上述优化算法结果表明,在两种情形下均可以获得较优的准方波脉冲输出,可以为准方波脉冲形成网络的工程实现提供一种新的方法。理论计算和电路仿真结果表明,所提出的方法合理可行。     

北京大学ERL装置交汇段的研究与设计

 在交汇段设计理论的基础上,针对北京大学ERL的具体情况,对交汇段的束流传输结构进行了优化设计,通过模拟得到了满足要求的一组设计参数;研究了空间电荷效应以及相干同步辐射对束流发射度、能散及包络的影响。结果表明：空间电荷效应对发射度影响不大,但对束流包络影响较明显;相干同步辐射引起的发射度增长及能散较小,且不影响束流包络。     

A lightweight cell switching and traffic offloading scheme for energy optimization in ultra-dense heterogeneous networks

One of the major capacity boosters for 5G networks is the deployment of ultra-dense heterogeneous networks (UDHNs). However, this deployment results in a tremendous increase in the energy consumption of the network due to the large number of base stations (BSs) involved. In addition to enhanced capacity, 5G networks must also be energy efficient for it to be economically viable and environmentally friendly. Dynamic cell switching is a very common way of reducing the total energy consumption of the network, but most of the proposed methods are computationally demanding, which makes them unsuitable for application in ultra-dense network deployment with massive number of BSs. To tackle this problem, we propose a lightweight cell switching scheme also known as Threshold-based Hybrid cEll swItching Scheme (THESIS) for energy optimization in UDHNs. The developed approach combines the benefits of clustering and exhaustive search (ES) algorithm to produce a solution whose optimality is close to that of the ES (which is guaranteed to be optimal), but is computationally more efficient than ES and as such can be applied for cell switching in real networks even when their dimension is large. The performance evaluation shows that THESIS significantly reduces the energy consumption of the UDHN and can reduce the complexity of finding a near-optimal solution from exponential to polynomial complexity.     

Global optimization method in millimeter wave combiner

This paper describes an algorithm which can determine the global optima of the power combiner of solid-state millimeter wave resonator. The global optimization mehtod can determine a neighborhood of the global optima of an objective function and an estimation of the global optima. In this paper the objective function as follow: In the quasi-optical resonator, the objective function are the fundamental mode power, the fractional power of fundamental mode and the combining dfficiecy were done the objective functiona respectively, to calculate the global optima respectively. In the power combiner of solid-state millimeter wave source in rectangular waveguide cavity. the performance parameter are presentes by combining efficiency, tuning range, frequency drift, and FM noise were done the objective functions respectively. And to calculate the global optima respectively.     

北京大学ERL装置交汇段的研究与设计

在交汇段设计理论的基础上,针对北京大学ERL的具体情况,对交汇段的束流传输结构进行了优化设计,通过模拟得到了满足要求的一组设计参数;研究了空间电荷效应以及相干同步辐射对束流发射度、能散及包络的影响。结果表明：空间电荷效应对发射度影响不大,但对束流包络影响较明显;相干同步辐射引起的发射度增长及能散较小,且不影响束流包络。     

Topology optimization using the improved element-free Galerkin method for elasticity

The improved element-free Galerkin(IEFG) method of elasticity is used to solve the topology optimization problems.In this method, the improved moving least-squares approximation is used to form the shape function. In a topology optimization process, the entire structure volume is considered as the constraint. From the solid isotropic microstructures with penalization, we select relative node density as a design variable. Then we choose the minimization of compliance to be an objective function, and compute its sensitivity with the adjoint method. The IEFG method in this paper can overcome the disadvantages of the singular matrices that sometimes appear in conventional element-free Galerkin(EFG) method. The central processing unit(CPU) time of each example is given to show that the IEFG method is more efficient than the EFG method under the same precision, and the advantage that the IEFG method does not form singular matrices is also shown.     

Design of URAs by DIRECT global optimization algorithm

Coded aperture imaging (CAI) has evolved as a standard technique for imaging high-energy photon sources and has found numerous applications. Coded aperture arrays (CAAs) are the most important devices in the applications of CAI. In recent years, many approaches were presented to design optimum or near-optimum CAAs. Uniformly redundant arrays (URAs) are the most successful CAAs for their cyclic autocorrelation consisting of a sequence of delta functions on a flat sidelobe, which can easily be subtracted when the object has been reconstructed. Unfortunately, the existing methods can only be used to design URAs with limited number of array sizes and fixed autocorrelative sidelobe-to-peak ratio. In this paper, we presented a method to design more flexible URAs by means of a global optimization algorithm named DIRECT. By our approaches, we obtain various types of URAs including the filled URAs which can be constructed by existing methods and the sparse URAs which have never been constructed and mentioned by existing papers as far as we know.