Orientation behavior of attapulgite nanoparticles in poly(acrylonitrile)/attapulgite solutions by rheological analysis

Nanocomposites based on poly(acrylonitrile) (PAN) and attapulgite (AT) had been prepared by solution blending in dimethyl sulfoxide (DMSO). The rheological properties of the nanocomposites solutions were investigated by HAAKE rheometer with plate‐cone geometry. The steady and oscillation shear experiments were carried out to investigate the effects of clay exfoliation and orientation as well as polymer‐clay interaction. The presence of small amount of AT nanoparticles with large aspect ratio improved the fluidity of these PAN solutions under low shear rate, whereas large amount of AT will reduce its aspect ratio by aggregation and constrain the polymer segment motion in the solutions. The relaxation and disentanglement behaviors of the PAN chains in nanocomposite solutions were also studied by oscillation and thixotropic experiments, from which, it can be concluded that well dispersed and oriented AT nanorods will reduce interaction among macromolecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 945–954, 2009     

Steady flow measurements on moderately concentrated solutions of poly(sodium acrylate)

Shear stress P₂₁ and normal stress P₁₁ –P₂₂ functions of moderately concentrated aqueous solutions of sodium poly (acrylate) were measured under steady shear flow at various shear rates \documentclass{article}\pagestyle{empty}\begin{document}$\dot \gamma$\end{document} with a Weissenberg rheogoniometer. The compliance function J_s = (P₁₁ – P₂₂)/2P₂₁² is found to vary with shear rate. The double logarithmic plot of J_s versus \documentclass{article}\pagestyle{empty}\begin{document}$\dot \gamma$\end{document} can be superposed with respect to molecular weight at constant concentrations of added neutral salt and polymer. These reduced plots differ markedly as the concentration of added salt is varied but converge to a single line at high shear rates.     

Rheology of concentrated solutions of poly(γ-benzyl-glutamate)

Steady shear viscosity, dynamic viscosity, dynamic modulus, and normal force were measured via rotational rheometry for concentrated solutions of racemic mixtures of poly(benzyl-glutamate) and poly(benzyl-D-glutamate) in m-cresol. A transition from the isotropic state to liquid-crystalline order with increase in concentration was indicated by optical anisotropy and maxima in all four material functions. This occurred at a critical concentration higher than the Flory prediction. Over a well-defined range of concentrations and shear stresses, some of the liquid-crystalline solutions exhibited negative first normal-stress differences that were not due to inertial effects.     

Rheological behavior of moderately concentrated silica suspensions in the presence of adsorbed poly(ethylene oxide)

Adsorption and flocculation properties have been investigated for a well-characterized aqueous system of precipitated nanometric silicabeads in the presence of a high molecular-weight poly(ethylene oxide). Particular attention was given to the evolution of these properties with increasing concentration. In addition, the corresponding consequences on the rheological behavior in the homogeneous domains of the phase diagram of the systems were studied. Important rheological effects can actually be obtained with such systems, even at moderate values of the volume fraction of the dispersed phase (5·10^–35·10^–2).According to the adsorption level, the number of particles per macromolecular chain, and the free polymer equilibrium concentration, quite different phenomena were observed such as rheopectic shear-induced gelation, Newtonian flow or thixotropic shear-thinning.     

Rheological properties of anisotropic poly(para-benzamide) solutions

A study has been made of the viscous properties of poly(para-benzamide) (PBA) solutions in dimethyl acetamide, which undergo a transition from an isotopic to an anisotropic (liquid-crystal) state at a definite concentration C^*. The polymer solutions behave in many respects (as regards the concentration and temperature dependence of viscosity, etc.) like solutions of low molecular weight compounds forming a liquid crystal phase, although the transitions are less pronounced in the polymer solutions owing to their polydispersity. It is shown that the viscometric method, being extremely sensitive to C^*, is convenient for determining phase diagrams of anisotropic polymer solutions. The values of C^* as related to the molecular weight of PBA have been determined, and a general criterion for transition from isotropic to anisotropic solutions established; the latter has the form (CM?)^* ≈ 1.3 × 10⁵ at 20°C. This criterion is in line with the condition for the formation of the liquid-crystal structure in a dispersion of rodlike particles as proposed by Flory. Generalized concentration dependences of viscosity have been plotted by reducing concentration to C^* and viscosity, to the maximum viscosity at the phase transition point. In investigating the flow properties of PBA solutions we revealed the existence of a yield point in the range of low shear stresses, and an intersection of the flow curves of solutions of different concentration at high shear stresses, which excludes a generalized representation of the flow curves in reduced ordinary-type coordinates.     

Dielectric relaxation in concentrated solutions of poly(γ-benzyl-L-glutamate)

Measurements of dielectric constant and loss, broad-line nuclear magnetic resonance, and differential thermal analysis of concentrated solutions of poly(γ-benzyl-L -glutamate) (PBLG) were carried out to determine the effects of intermolecular interactions on the mobility of the side group and the solvent (dichloromethane or dioxane). Only one dielectric loss peak due to the cooperative motion of the side group and the solvent was found. The activation energy of this relaxation process varied from 3 to 47 kcal/mole with increasing concentration of PBLG from 20 to 100% by weight accompanied with steep increases at about 40 and 80%. This result is explained as due to entanglement of neighboring side groups. In NMR, narrowing of the line was observed near the temperature where the dielectric loss was observed. The glass transition was also observed by differential thermal analysis. From these results it was concluded that the relaxation observed in PBLG solution and in pure PBLG have the nature of primary or α relaxations.     

Viscosity of poly(vinyl acetate) and its concentrated solutions

Data on the viscosity of poly(vinyl acetate) (PVOAc) and its concentrated solutions in diethyl phthalate (DEP) and cetyl alcohol (CeOH) are examined over the molecular weight range 8 × 10³ < M < 1.3 × 10⁶, the range 0.15 < φ < 1.0 of the volume fraction φ of polymer, the temperature range 308 to 430°K for PVOAc and its solutions in DEP, and at 396°K in CeOH. The latter is the θ temperature for dilute solutions of PVOAc in CeOH. The data are analyzed with the relation η = KX_c(αφM/M_c)^a exp[1/β(T – T₀)], where a is 1 or 3.4 for αφM less than or greater than a constant M_c, respectively, and X_C, is a constant. The expansion factor α_φ of the chain dimension is found to be essentially unity for φ > ca. 0.25, increasing with decreasing φ for smaller φ. Both β and T₀ depend on φ, and T₀ also depends on M at low M.     

Rheological properties of poly(ethylene glycol) solutions and gels

By the interaction of a water–glycol solution of poly(ethylene glycol) (PEG) with calcium chloride dihydrate, a gel was produced. It was determined that, below a certain shear rate, this gel is a Newtonian fluid; however, above a certain shear rate, which depends on the gel viscosity, the properties of this gel are anomalous: the gel flow instantaneously completely stops. The viscosity of the gels was found to exponentially increase with increasing concentration of the cross-linking metal at constant PEG concentration. The density of the gels linearly increases with increasing concentration of the cross-linking metal at constant PEG concentration.     

Thermal behavior of the highly luminescent poly(3-hydroxybutyrate):Eu(tta)3(H2O)2 red-emissive complex

The aim of this study has been to gain a fundamental understanding of the mechanisms governing thermal degradation of luminescent poly(3-hydroxybutyrate) (PHB). PHB was doped with diaquatris(thenoyltrifluoroacetonate) europium(III) complex, [Eu(tta)₃(H₂O)₂], and different luminescent systems were obtained. The thermal-stability of the luminescent films was discussed and the products of decomposition were analyzed. Thermal degradation of PHB:Eu(tta)₃ x % systems (x = 0, 1, 5, 10, and 15 %) was elucidated by means of thermogravimetric analysis (TG), the thermal-stability decreases with the increase of europium complex concentration. The PHB polymer decomposed with evolution of carbon dioxide and 2-butenoic acid molecules. The TG–FTIR results, of the gaseous degradation products of PHB in nitrogen atmosphere, indicated that the polymer is stable at temperatures up to 200 °C. Polymer matrix at concentrations above 5 % decomposed with evolution of water molecules among the other gaseous products, which implied the presence of a hydrated complex in the system. The luminescent films showed more flexibility due to a loss in crystallinity, which suggested a potential usefulness in technical applications.     

Dielectric relaxation in concentrated solutions of poly(methyl methacrylate)

Measurements of dielectric relaxation have been made for a series of solutions of poly(methyl methacrylate) in toluene. A range of concentrations between 2% and 20% was used for a number of polymers of differing molecular weights. The dispersion was studied over the frequency range 10³-10⁶ Hz for temperatures between ?90°C and +20°C. It has been found that both the distribution of relaxation times and the activation energy increase with increasing concentration. The magnitudes of the effects vary with molecular weight. A significant observation is that the increase in dielectric constant with concentration is not linear.     

Viscometry and light scattering on moderately concentrated solutions of poly(vinyl chloride)

Moderately concentrated solutions (0.015–0.10 g/mL) of poly(vinyl chloride) have been studied in three different solvents by light scattering and viscometry. It is concluded that intermolecular association occurs in all solutions studied, including data over the temperature interval 25–110°C. The data can be interpreted in terms of a model with loci of association holding chains together in an aggregate that has an overall configuration similar to that of a randomly branched polymer.     

Rheological properties of poly(1-trimethylsilyl-1-propyne) solutions

The phase state and rheological properties of poly(1-trimethylsilyl-1-propyne) solutions in toluene and cyclohexane are studied. Samples of poly(1-trimethylsilyl-1-propyne) have the same backbone structure (cis-trans configuration ratio) but different molecular masses. Phase diagrams of these systems are derived via optical interferometry. It is found that they have an upper critical mixing temperature (UCMT) whose value exceeds the boiling points of the individual solvents. The two solvents exhibit limited solubility with respect to the studied polymer, and this parameter decreases with an increase in the molecular mass of the polymer. In the transition from dilute to concentrated solutions, the pattern of the rheological behavior changes from Newtonian to pseudoplastic. The concentration dependences of the zero-shear-rate viscosity of the solutions are typical for flexible-chain polymers. The viscous behavior of the poly(1-trimethylsilyl-1-propyne)-solvent system can be described through a single generalized viscosity-concentration relationship if dimensionless reduced values that take into account the contribution of the molecular mass, the nature of the solvent, and the pattern of intermolecular interactions in the solutions are used as the argument and the function.     

Viscosity of concentrated solutions of polystyrene and poly(vinyl acetate) (empirical equations)

The viscosity of solutions of polystyrene with M _w from 2.8 × 10⁴ to 7.8 × 10⁵ in toluene and of poly(vinyl acetate) with M _w from 2 × 10⁴ to 1.4 × 10⁵ in butyl acetate at 30–80°C is measured. The dependence of the activation energy of the viscous flow of the solutions on the molecular weight of the polymers and solution concentration is examined. This dependence is approximated by a cubic polynomial for polystyrene solutions and by a quadratic polynomial for poly(vinyl acetate) solutions. The dependences of the solution viscosity on the concentration, molecular weight, and temperature are approximated by exponential equations in which the exponents are sums of polynomials. The coefficients of the polynomials are determined.     

Phase behavior of poly(sulfobetaine methacrylate)-grafted silica nanoparticles and their stability in protein solutions

Biocompatible and zwitterionic poly(sulfobetaine methacrylate) (PSBMA) was grafted onto the surface of initiator-modified silica nanoparticles via surface-initiated atom transfer radical polymerization. The resultant samples were characterized via nuclear magnetic resonance, Fourier transform infrared spectroscopy, transmission electron microscopy, and thermogravimetric analysis. Their molecular weights and molecular weight distributions were determined via gel permeation chromatography after the removal of silica by etching. Moreover, the phase behavior of these polyzwitterionic-grafted silica nanoparticles in aqueous solutions and stability in protein/PBS solutions were systematically investigated. Dynamic light scattering and UV-visible spectroscopy results indicate that the silica-g-PSBMA nanoparticles exhibit an upper critical solution temperature (UCST) in aqueous solutions, which can be controlled by varying the PSBMA molecular weight, ionic strength, silica-g-PSBMA nanoparticle concentration, and solvent polarity. The UCSTs shift toward high temperatures with increasing PSBMA molecular weight and silica-g-PSBMA nanoparticle concentration. However, increasing the ionic strength and solvent polarity leads to a lowering of the UCSTs. The silica-g-PSBMA nanoparticles are stable for at least 72 h in both negative and positive protein/PBS solutions at 37 °C. The current study is crucial for the translation of polyzwitterionic solution behavior to surfaces to exploit their diverse properties in the development of new, smart, and responsive coatings.     

Synthese und Strukturanalyse von Na3SbSe3·3Sb2O3·0,5Sb(OH)3

Investigations in the system Sb-Se-NaOH-H₂O, hydrothermal conditions, yielded crystals of the compound Na₃SbSe₃·3Sb₂O₃·0,5Sb(OH)₃. The structure of this compound (a=14.40 Å,c=5.568 Å; space group P 6₃-C ₆ ⁶ ;Z=2) was determined from 985 independent X-ray intensities — collected on an automaticWeissenberg type diffractometer — by thePatterson method and refined by the least squares method toR=8.3% (with -weighting 5.9%). The structure consists of SbO₃ pyramids which are connected via common oxygen corners to tubes parallel [001]. These tubes and SbSe₃ pyramids are combined by Na atoms to a framework. The Sb(OH)₃ groups are statistically located within the channels of the tubes.

     

Interactions of O(2) with Pd nanoparticles on alpha-Al(2)O(3)(0001) at low and high O(2) pressures

The interaction of O(2) with small Pd particles (2-10 nm) supported on an alpha-Al(2)O(3)(0001) single crystal under both ultrahigh vacuum (UHV) and high-pressure conditions has been studied by temperature-programmed desorption (TPD), temperature-programmed low-energy ion scattering (TP-LEIS), and X-ray photoelectron spectroscopy (XPS). A low O(2) exposure (30 L) at 500 K leads to surface oxygen adatoms on the Pd nanoparticles, which desorb in TPD as O(2) in a peak at approximately 880 K. Surface O adatoms on the smallest Pd particles move to subsurface sites starting at 400 K, and they almost all move subsurface by approximately 750 K, desorbing mainly at considerably higher temperature. The dominant oxygen species above 700 K is subsurface, implying that it is more stable than oxygen adatoms on Pd. Exposures of the Pd nanoparticles to 25 Torr O(2) at 373-473 K readily convert the Pd to a species whose Pd XPS peak shifts by the same amount as the binding energy difference between bulk Pd and bulk PdO. We attribute this to PdO nanoparticles (or a thin film of PdO on or under the Pd for the larger particles). The decomposition of the PdO on these nanoparticles to Pd in an equilibrium O(2) pressure of 10-7 Torr does not occur until approximately 750 K, or approximately 200 K higher than the equilibrium decomposition of bulk PdO. This is attributed to the higher energy of Pd nanoparticles compared to bulk Pd and, for the larger particles, to the adhesion energy of the PdO film to the Pd, both of which stabilize the PdO on these Pd nanoparticles relative to bulk PdO. This PdO-like film on the larger particles may be similar to the ordered oxide thin film previously reported to form on Pd(111) but may also reside at the alpha-Al(2)O(3) interface and be partially stabilized by adhesion to this interface.     

Ultra small Gd(2)O(3) nanoparticles: Absorption and emission properties

In this paper, we report a facile method for synthesis of ultra small (1-3nm) gadolinium oxide (Gd(2)O(3)) nanoparticles using citric acid (CA) as a capping agent. The dependence of nanoparticle (NP) size on the ratio between CA and gadolinium (Gd) is investigated. Absorption properties of the ultra small Gd(2)O(3) NPs in UV region have four characteristic peaks at 312nm, 274nm, 253nm and 228nm. Finally, we show that the Gd(2)O(3) nanoparticles synthesized by this method induce triplet emission (phosphorescence) from CA and EG in the NIR region.     

Spontaneous copolymerization of 2-acrylamido-2-methylpropanesulfonic acid with acrylamide and acrylonitrile in concentrated aqueous solutions

Spontaneous copolymerization of 2-acrylamido-2-methylpropanesulfonic acid with acrylamide and acrylonitrile in concentrated acidic aqueous solutions was studied.     

Anion specific adsorption on Fe2O3 and AlOOH nanoparticles in aqueous solutions: comparison with hematite and gamma-Al2O3

The specific adsorption of radiolabeled sulfate and phosphate ions from perchlorate supporting electrolyte onto nano-AlOOH and nano-Fe(2)O(3) powder has been investigated. The pH dependence of the adsorption of anions onto nanopowders was compared with that of the same ions onto gamma-Al(2)O(3) and hematite. It was demonstrated that the character of the pH dependence of the adsorption is very similar in the comparable cases. It was found, however, that in contrast to the behavior of gamma-Al(2)O(3), nano-AlOOH dissolves at a significant rate at low pH values (pH<2). Thus the study of the pH dependence of the anion adsorption encounters difficulties at these pH values. Disregarding this fact, it can be concluded that no special effects can be observed in the anion adsorption onto the nano-oxides studied.     

Rheological investigation of aqueous solutions of poly(vinyl alcohol) during ageing

The changes in viscosity and normal stress difference during the ageing of concentrated aqueous solutions of poly(vinyl alcohol) prepared at 80 °C and the effect of the procedure used in the preparation of solutions on the course of these changes are described. The results are interpreted by means of shear complianceJ _e and relaxation time ₀.