Simultaneous determination of residual synthetic antibacterials in fish by high-performance liquid chromatography

A simple and rapid high-performance liquid chromatographic (HPLC) method for the simultaneous determination of sulphamonomethoxine (SMMX), sulphadimethoxine (SDMX), sulphisozole (SIZ), nalidixic acid (NA), oxolinic acid (OXA), piromidic acid (PMA), furazolidone (FZ) and sodium nifurstyrenate (NFSA) in cultured fish was developed. The drugs were extracted with 0.2% metaphosphoric acid-methanol (6:4), followed by a Bond Elut C18 clean-up procedure. The HPLC separation was carried out on an Inertsil ODS column (150 x 4.6 mm I.D.) using 5 mM aqueous oxalic acid-acetonitrile (55:45) as the mobile phase with detection at 265 nm (0.04 a.u.f.s.). The calibration graphs were rectilinear from 1 to 20 ng for OXA, from 2 to 50 ng for SMMX, SDMX, SIZ, NA, PMA and FZ and from 5 to 100 ng for NFSA. The recoveries of each drug added to fish were 65.0-89.5%. The detection limits were 0.02 micrograms/g for OXA, 0.05 micrograms/g for SMMX, SDMX, SIZ, NA, PMA and FZ and 0.1 micrograms/g for NFSA.     

Hydrolysis study of organic acid anhydrides by differential thermal analysis-I Pyromellitic dianhydride

A technique for following the hydrolysis of pyromellitic acid dianhydride (PMDA) by differential thermal analysis (DTA) is described. On exposure of PMDA to moisture, an endothennic peak is initiated between 190 and 200 degrees . As the degree of hydrolysis increases, this peak becomes more intense and shifts to higher temperatures. The formation of pyromellitic acid (PMA) during the hydrolysis of PMDA can be determined qualitatively by DTA.     

Thermal characterization of usnic acid/collagen-based films

The purpose of this study was to evaluate the physical–chemical properties of collagen (CL) and usnic acid/collagen-based (UAC) films, using differential thermal analysis (DTA), thermogravimetry (TG/DTG), infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Both films were prepared by casting process using polyethylene glycol 1500 (PEG 1500) as plasticizer. In the spectrum of UAC, similar bands of the usnic acid are observed, indicating that the polymerization (film formation) did not affect the stability of the drug. Distinctly, DTA curve of UAC did not show an endothermic peak at 201 °C, indicative that the drug was incorporated into the polymeric system. These results were corroborated by the scanning electron microscopy (SEM). The TG/DTG curves of UAC presented a different thermal decomposition profile compared to the individual compounds and CL. These findings suggest the occurrence of molecular dispersion or solubilization of the drug in the collagen film.     

Reversible Protein Adsorption on PMOXA/PAA Based Coatings: Role of PAA

In this study we report design of stimuli-responsive coating based on poly(2-methyl-2-oxazoline-random-glycidyl methacrylate)(PMOXA-r-GMA) comb copolymer and poly(acrylic acid)-block-poly(glycidyl methacrylate)(PAA-b-PGMA) block copolymers and scrutinize its ability to control protein adsorption. Firstly, PMOXA/PAA based coatings were prepared by simply spin coating the mixture of PMOXA-r-GMA and PAA-b-PGMA copolymer solutions onto silicon substrates followed by annealing at 110 °C.Then coatings were rigorously characterized by X-ray photoelectron spectroscopy(XPS), the static water contact angle(WCA) test,ellipsometry and atomic force microscopy(AFM). After that, the relationship of switchable behavior of PMOXA/PAA based coatings with PAA content and chain length was investigated through the change of thickness and WCA upon pH and ionic strength(I) trigger,which indicated that the change in thickness and WCA was triggered when PAA contents were increased as well as by increasing chain length of PAA in PMOXA/PAA based coatings. Finally, real-time adsorption/desorption of lysozyme(Lyso) on PMOXA/PAA based coatings was monitored using quartz crystal microbalance with dissipation monitoring(QCM-D). The results showed that the Lyso adsorption amount was increased upon increasing chain length and contents of PAA in PMOXA/PAA based coatings. The adsorbed Lyso was then efficiently desorbed by changing pH and I of medium with the maximum desorption( 90% desorption percentage) observed for the suitable ratio of PMOXA and PAA while chain length of PAA was kept longer than that of PMOXA. Furthermore, the prepared coatings were found to repeatedly adsorb and desorb Lyso for four successive cycles of adsorption/desorption, which confirmed the stability of prepared coatings.     

ToF-SIMS analysis of poly(l-lysine)-graft-poly(2-methyl-2-oxazoline) ultrathin adlayers

Understanding of the interfacial chemistry of ultrathin polymeric adlayers is fundamentally important in the context of establishing quantitative design rules for the fabrication of nonfouling surfaces in various applications such as biomaterials and medical devices. In this study, seven poly(l-lysine)-graft-poly(2-methyl-2-oxazoline) (PLL–PMOXA) copolymers with grafting density (number of PMOXA chains per lysine residue) 0.09, 0.14, 0.19, 0.33, 0.43, 0.56, and 0.77, respectively, were synthesized and characterized by means of nuclear magnetic resonance spectroscopy (NMR). The copolymers were then adsorbed on Nb₂O₅ surfaces. Optical waveguide lightmode spectroscopy method was used to monitor the surface adsorption in situ of these copolymers and provide information on adlayer masses that were then converted into PLL and PMOXA surface densities. To investigate the relationship between copolymer bulk architecture (as shown by NMR data) and surface coverage as well as surface architecture, time-of-flight secondary ion mass spectrometry (ToF-SIMS) analysis was performed. Furthermore, ToF-SIMS method combined with principal component analysis (PCA) was used to verify the protein resistant properties of PLL–PMOXA adlayers, by thorough characterization before and after adlayer exposure to human serum. ToF-SIMS analysis revealed that the chemical composition as well as the architecture of the different PLL–PMOXA adlayers indeed reflects the copolymer bulk composition. ToF-SIMS results also indicated a heterogeneous surface coverage of PLL–PMOXA adlayers with high grafting densities higher than 0.33. In the case of protein resistant surface, PCA results showed clear differences between protein resistant and nonprotein-resistant surfaces. Therefore, ToF-SIMS results combined with PCA confirmed that the PLL–PMOXA adlayer with brush architecture resists protein adsorption. However, low increases of some amino acid signals in ToF-SIMS spectra were detected after the adlayer has been exposed to human serum.

Thermal characterization of HCN polymers by TG-MS, TG, DTA and DSC methods

This paper presents a thermogravimetry (TG) study of hydrogen cyanide polymers, synthesized from the reaction of equimolar aqueous solutions of sodium cyanide and ammonium chloride. Differential thermal analysis (DTA) and differential scanning calorimetry (DSC) were also used to evaluate the thermal behaviour of these black polymers, which play an important role in prebiotic chemistry. A coupled TG-mass spectrometer (MS) system allowed us to analyze the principal volatile thermal decomposition and fragmentation products of the isolated HCN polymers under dynamic conditions and an inert atmosphere. After dehydration, a multi-step decomposition occurred in this particular polymeric system, due to the release of ammonia, hydrogen cyanide (depolymerization reaction), isocyanic acid (or cyanic acid) and formamide; these two latter species allow us identify bond connectivities. Finally, data collected from TG experiments in an oxidative atmosphere showed significant differences at higher temperatures, above 400 °C. According to these results, the different techniques of thermal analysis here applied have demonstrated to be an adequate methodology for the study and characterization of this complex macromolecular system, whose structure remains controversial even today.     

Na-MMT掺杂对PMA/PVP复合膜结构及光致变色性能的影响研究

将钠基膨润土(Na-MMT)掺入磷钼酸/聚乙烯基吡咯烷酮(PMA/PVP)体系中,利用透射电子显微镜(TEM)、原子力显微镜(AFM)、红外光谱(FTIR)、热重-差热(TG-DTA)、紫外-可见吸收光谱(UV-Vis)、X射线光电子能谱(XPS)等手段对复合薄膜的结构、热稳定性和光致变色性能进行了研究.红外光谱结果表明keggin结构磷钼酸和聚乙烯吡咯烷酮的基本结构在复合膜中仍然存在,复合膜中高分子与质子结合,以阳离子的形式与杂多阴离子成盐.Na-MMT的掺杂未对复合膜中PVP和PMA间的相互作用产生影响,但其掺杂提高了复合膜的热稳定性.在紫外光照下,复合膜由无色变为蓝色,杂多酸被还原产生杂多蓝.Na-MMT的掺杂降低了复合膜的光致变色响应性,这是由于多酸分子与钠基膨润土之间发生阳离子交换作用导致的.     

Thermal and spectral properties of natural bentonites and their applications as reinforced nanofillers in polymeric materials

This study deals with possibility of the applications of inorganic substances specifically natural bentonite in function of reinforced nanofillers in polymeric materials. X-ray diffraction, FTIR spectroscopy and thermal analysis (TG, DSC and DTA) were used to characterize natural bentonite in more detail. At the prepared model, rubber compounds with various amounts of added filler were determinated vulcanization characteristics and physical–mechanical properties. The measured values were compared with the values of commercially used polymeric materials with the original composition.     

Phosphomolybdic acid supported on silica gel and promoted with alkali metal ions as catalysts for the esterification of acetic acid by ethanol

Different ratios of phosphomolybdic acid PMA supported on silica gel (1–30 wt%) and promoted with alkali metal hydroxide have been prepared by an impregnation method and calcinated at 350 °C for 4 h. The catalysts were characterized by thermogravimetry (TG), differential thermal analysis (DTA), X-ray diffraction, FT-IR spectroscopy and N₂ adsorption measurements. The surface acidity and basicity of the catalysts were determined by adsorption of pyridine and the dehydration–dehydrogenation of 2-propanol. The gas-phase esterification of acetic acid by ethanol was carried out in a conventional flow bed reactor. The results clearly revealed that among the PMA loading, the use of 10 wt% catalyst showed maximum yield of ethyl acetate. This catalyst also improved on addition of Na or K-hydroxide. These results were correlated with the structure and the acid–base properties of the prepared catalysts.     

Cyclic Polymer Grafts That Lubricate and Protect Damaged Cartilage

Tissue‐reactive graft copolymers were designed to protect the cartilage against enzymatic degradation and restore its lubrication properties during the early stages of osteoarthritis (OA). The copolymers feature a poly(glutamic acid) (PGA) backbone bearing hydroxybenzaldehyde (HBA) functions and cyclic poly(2‐methyl‐2‐oxazoline) (PMOXA) side chains. PGA‐PMOXA‐HBA species chemisorb on the degraded tissue via Schiff bases and expose the biopassive and lubricious PMOXA cyclic grafts at the interface. The smaller hydrodynamic radius by cyclic PMOXA side chains coupled to the intrinsic absence of chain ends generate denser and more lubricious films on cartilage when compared to those produced by copolymers bearing linear PMOXA. Topology effects demonstrate how the introduction of cyclic polymers within tissue‐reactive copolymers substantially improve their tribological and biopassive properties, suggesting a plethora of possible applications for cyclic macromolecules in biomaterials formulations.     

Synthesis,characterization, thermal,electrical and magnetic properties of polyaniline composites with rare earth gadolinium coordination complex

Novel polyaniline/gadolinium (PANI/Gd) composites were successfully synthesized by “in‐situ” polymerization at the presence of rare earth Gd coordination complex and D‐tartaric acid (an a dopant). It is rarely to find the studies on related field to add rare earth Gd coordination complex as fillers. Fourier transform infrared (FTIR) spectra, X‐ray diffraction (XRD) and scanning electron microscope (SEM) were used to examine the structure and surface appearance characterization of materials. The thermal stability performance of composites was investigated by thermogravimetry and derivative thermogravimetry (TG‐DTG). Electrochemical performance was measured by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge–discharge test. The magnetic property was investigated by physical property measurement system (PPMS). The structure and surface appearance characterization and the magnetic properties jointly demonstrate the polymerization of rare earth Gd coordination complex and PANI–D‐tartrate (DTA) not only simple physical mixing but also chemical mixing. TG‐DTG analysis suggests that thermal stability of PANI/Gd composites is higher than that of PANI–DTA. Electrochemical performance tests and SEM indicate that the composite (PANI/Gd = 3.3:1,mass ratio) has the most regular morphology and best specific capacitance. The magnetization of the composite (PANI/Gd = 3.3:1,mass ratio)is evidently smaller compared with PANI–DTA and rare earth Gd coordination complex. Copyright © 2016 John Wiley & Sons, Ltd.     

In situ solid-state NMR characterization of pharmaceutical materials: An example of drug-polymer thermal mixing

Pharmaceutical amorphous solid dispersions, a multicomponent system prepared by dispersing drug substances into polymeric matrix via thermal and mechanical processes, represent a major platform to deliver the poorly water-soluble drug. Microscopic properties of drug-polymer contacts play mechanistic roles in manipulating long-term physical stability as well as dissolution profiles. Although solid-state nuclear magnetic resonance has been utilized as an indispensable tool to probe structural details, previous studies are limited to ex situ characterizations. Our work provides likely the first documented example to investigate comelting of ketoconazole and polyacrylic acid, as a model system, in an in situ manner. Their physical mixture is melted and mixed in the solid-state nuclear magnetic resonance rotor under magic angle spinning at up to approximately 400 K. Critical structural events of molecular miscibility and interaction have been successfully identified. These results design and evaluate the instrumental and experimental protocols for real-time characterizations of the comelting of pharmaceutical materials.     

Thermal decyanation,a new organic reaction. II

When heated in solution at about 160°C, pyridine quaternary salts of bromomalonamides lose 1 mole of cyanic or isocyanic acid almost quantitatively in a manner quite analogous to the decarboxylation of an acid. By DTA and DSC, the crystalline salts are stable up to their melting points (>220°C) at which temperatures concurrent fusion and decyanation processes occur (endotherm); these are immediately followed by an exotherm related to the trimerization of cyanic acid. TGA measurements on the solid salts do not clearly define the loss of 1 mole of cyanic acid because in the solid state, thermal decyanation is accompanied to some extent by other pyrolytic reactions. Preparative methods for quaternizing poly(4-vinylpyridine) with bromomalonamide are described and two polymeric quaternary salts (33 and 100% substituted) were prepared and analyzed. These polyelectrolytes are water soluble and upon the addition of base the yellow polymeric nitrogen ylids are generated. Infrared spectra on the polymeric quaternary salts and visible spectra on the polymeric ylids are included. The ylid chromophore has an ε = 1800 at λ_max = 415 nm. The dilute solution viscosity behavior of these polymers in H₂O and in 0.05N KBr is typical of polyelectrolytes. Both polymers in dilute solution show a maximum in η_sp versus pH plots. In water, the viscosity of these polymers decreases with time, and it is proven that this results from a conformational change which accompanies amide hydrolysis rather than polymer backbone degradation. Glass transitions are not detectable by DTA but both polymers show well-defined trimerization exotherms for cyanic acid starting at 170–175°C. Thus, decyanation of the solid polymeric quaternary salts is more analogous to decyanation of the crystalline quaternarys in solution than as solids. TGA measurements on the polymers show weight losses which are of the correct order of magnitude and in the correct temperature range for monodecyanation. Some data are presented which suggest that perhaps a second mole of cyanic acid is lost at about 250°C. Quaternization of poly(4-vinylpyridine) with bromomalonamide reduces its gross decomposition temperature from 385°C to about 285–317°C. It is demonstrated how thermal decyanation can be used for the in situ generation of cyanic acid for the modification of organic compounds. The preparation of a partial urethane of poly(vinyl alcohol) using this method is described. We have also shown that aliphatic quaternary salts can be prepared and that they too undergo the decyanation reaction.     

Dynamic dielectric analysis. A new thermal analysis technique

Applications of dynamic dielectric analysis (DDA) in studies on the thermal decomposition and phase transformations of solid materials are discussed. Three illustrative examples are presented for (a) a system undergoing a chemical reaction or thermal alteration on application of heat, (b) a system undergoing a crystallographic transformation and (c) detection of moisture in naturally occurring materials. The advantages derived by applying a combination of DDA and a conventional thermal analysis technique such as DTA to studies on thermal processes are demonstrated. It is shown that the information obtained from techniques such as DTA or TG is limited in scope unless used in conjunction with a method which sheds light on the mechanistic aspects of the physical or chemical process of interest.     

Synthesis of ZrO2-based ceramic pigments

The pigments used in ceramic applications are of nature predominantly inorganic and they should be thermally stable, insoluble in glazing, resistant to the chemical and physical agents' attacks. This work aimed at the synthesis by the polymeric precursor method of ZrO₂-based inorganic pigments, doped with Fe, Ni, Co, Cr and Cu cations. The fired pigments were characterized by thermogravimetry (TG), differential thermal analysis (DTA) and X-ray diffraction (XRD). Among the metals used to zirconium-doping, the best result was achieved with the cations Cu, which presented the monophase pigment, even as 20 mol% of dopant. Up to the temperature of 1000°C the pigments presented a good thermal stability. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis and analytical properties of a novel columnar metallomesogenic polymer

A metallomesogenic side-chain polymer with copper carboxylato discotic units in stacks prepared by covalent bonding of 14-pentadecenoic acid, stearic acid and poly(methylhydrosiloxane) is described. The physico-chemical and thermal properties of both monomeric and polymeric metallomesogens were determined by elemental analysis, IR, polarizing optical microscopy, thermal gravimetric analysis and differential scanning calorimetry. The polymeric states showed a discotic lamellar phase at 50-95 degrees C and an ordered discotic hexagonal phase at 95-200 degrees C. By dynamic coating, the metallomesogenic polymer was crosslinked to the capillary wall via benzoyl peroxide. The wall-coated capillary columns (15 m x 0.25 mm I.D.) were used for the separation of phenols. Factors affecting the retention and the sample selectivity were examined. Van 't Hoff plots as a function of temperature indicated that phase transitions were occurring. Thermodynamic properties of the analytes in this system were also studied. For the determination of a mixture of 3-aminophenol, 2-chlorophenol, 2-nitrophenol, 4-nitrophenol, o-methylphenol, m-methylphenol, p-methylphenol, 2,4-dichlorophenol, 2,4-dimethylphenol, 2,4-dinitrophenol, 2,4,6-trichlorophenol, 2,4,6-trimethylphenol, 4-bromophenol, 3-methyl-4-chlorophenol, pentachlorophenol, and unsubstituted phenol, the calibration graphs for most phenols were linear over the range of 10-1000 microg ml(-1) and the mass detection limits were in the ng range based on three times standard deviation of seven measurements of the lowest peak that could be detected.     

Thermal characteristics of ammonium nitrate, carbon, and copper(II) oxide mixtures

Ammonium nitrate (AN) has been extensively used as an oxidizer in energetic compositions, and is a promising compound as a propellant and gas generator. It is well-known that metal oxides help to address some of the disadvantages of AN, such as low stability and a low burning rate in these applications. In order to investigate the effects of copper(II) oxide (CuO) on the thermal decompostion of AN mixtures, the thermal characteristics of AN, carbon, and CuO mixtures were measured using simultaneous differential scanning calorimetry and thermogravimetry–differential thermal analysis connected with infrared spectroscopy and mass spectrometry. As a combustible material, activated carbon (AC), and carbon black (CB) were used in this study. In the TG–DTA results for AN/AC/CuO and AN/CB/CuO mixtures in an open cell, an exotherm was observed at approximately 210 and 230 °C, respectively. In addition, the IR and mass spectra of the gases produced from the AN/AC/CuO and AN/CB/CuO mixtures indicated the presence of CO₂. Notably, the effect of CuO addition on the oxidation of the AN/AC/CuO mixture was different from that on the AN/CB/CuO mixture; the oxidation of AC shifted to a lower temperature, while the oxidation of CB shifted to a higher temperature. These results suggest that the effect of CuO on the oxidation of different types of carbon depends on the chemical reactivity of the carbon, which is derived from its physical properties.     

Development of Bionic Polymers

Bionics, an artificial imitation of natural products, has always been a forever dream in the fairy tale or scientific fiction when we were childhood and children live now. However, the development of science in molecular scale makes this dream of childhood and manhood realize today.Bionics, a branch of science concerned with application the data about the functioning of biological system to the solution of engineering problems, become top-priority of science in the 21st century.However, few examples are given in molecular-level or nano-scale controlling lotus-like surface (a bionic surface for vast potential application). In the same time, such a typical bionic surface (as well known, so called "Lotus-effect") is a symbol or a totem that scientists can develop a novel approach to prepare desired surface and to control its microstructure or morphology at one's pleasure.In general, a film with a water contact angle (CA) higher than 150° can be defined as a superhydrophobic surface. The Langmuir-Blodgett film prepared by using CF3(CF2)10COOH possesses the lowest surface tension, which is 6 mJ/m2 (1). However, the water CA on a smooth surface with regularly aligned C20F42 with close-hexagonal packed -CF3 groups is only 119° (2).Obviously, only adjusting chemical composition is not enough to produce a superhydrophobic surface. Wenzel et al (3) suggested that the contact angle θ' of a liquid droplet on a rough solid surface should be written as:cosθ, =γcosθ = γ(γs-γsl)/γl, here γ is a roughness factor and γsl, γs and γl denote the interfacial tensions of the solid-liquid, the solid-gas, and the liquid-gas interfaces,respectively. This γ is always larger than 1 and a rough surface will be more water-repellent or more wettable to a liquid when intrinsic contact angle θ is bigger or smaller than 90°, respectively.Therefore, a general approach to obtain superhydrophobic surfaces is using a combination of depressing surface energy and enhancing surface roughness (4-17).Super-hydrophobic polymeric surface has been prepared in this case with a mixture of low-cost fluorine-end-capped polyurethane(FPU) and commonly available polymethyarylates(PMA) under ambient conditions. No obvious structures were observed by SEM for the pure FPU coated surface.The surface morphology is uniformly smooth at both low and high magnifications. The CA on the surface is about 95°, which indicates that FPU film has better hydrophobicity than pure polyurethane without fluorine-group, whose CA is about 65°. However, the hydrophobicity of polymer surface changes dramatically as the film is directly prepared through a one-step coating of a FPU/PMA solution between 10-30℃. The CA is up to 166 . The result shows that the SA can be dramatically decreased with small amount of FPU, and the SA reached a limiting value of 3.4 ± 2.0 ° when the FPU content in the FPU/PMA mixture is between 20 ～ 60 wt%. The water drop is unstable on these surfaces, and with a very small tilt-angle, the water drop will roll off the surface.It means that such a polymeric surface exhibits an excellent superhydrophobicity. In addition, the polymer surface possesses not only a better hydrophobicity than that of natural lotus leaf (CA measured is about 160°), but also a lypophobic property: the oil contact angle on the same surface is 140°, while the surface of lotus is lypophilic. Most interestingly, we have found that the coated film prepared by FPU/PMA mixture has a two-length scaled rough micro-nano-binary structure, that is, every micro-papilla (300-700nm) on the polymeric surface is also covered by nano-papillae ranging from 30-40nm. These MNBs is very much the same as the natural lotus-leaf surface in micro- and nano-scales. Compared with lotus surface structure, the NMBs structure on this bionic polymeric surface prepared is in less scale. The results clearly demonstrated that a bionic polymeric surface similar to the natural lotus-leaf surface can be obtained by a one-step coating process. The results showed also that such a bionic polymeric surface possess of some "self-repairing" properties similar to that of natural surfaces and the effects of preparation temperature and concentration as well as substrate made no obvious difference on the hydrophobicity of the bionic polymeric surfaces..In conclusion, we demonstrated that the MNBs of a bionic polymeric film has been one-step obtained with the use of the self-aggregation of PMA combining with a nano-scaled phase separation of amphiphilic copolymer during the drying process in ambient atmosphere. This remarkable result provides many potential possibilities, including coating, hygienic, medical,environmental, and industrial processing applications.     

基于聚(2-甲基-2-噁唑啉)和聚丙烯酸的混合刷在毛细管电泳在线富集溶菌酶中的应用

制备了一种对溶菌酶具有可控吸附性能的混合刷涂层毛细管,用于毛细管电泳在线富集溶菌酶以提高其检测灵敏度。首先,分别通过阳离子开环聚合和可逆加成-断裂链转移（RAFT）聚合合成聚（2-甲基-2-噁唑啉）（PMOXA）和聚丙烯酸（PAA）,然后将甲基丙烯酸缩水甘油酯（GMA）分别与PMOXA和PAA通过自由基共聚和RAFT聚合合成出聚（2-甲基-2-噁唑啉）-r-甲基丙烯酸缩水甘油酯（PMOXA-r-GMA）和聚丙烯酸-b-聚甲基丙烯酸缩水甘油酯（PAA-b-PGMA）。将PMOXA-r-GMA和PAA-b-PGMA的混合溶液以一定比例加入到毛细管内,通过加热即可制备出基于PMOXA和PAA的混合刷涂层毛细管。X射线光电子能谱（XPS）对毛细管原材料的表面组成研究结果表明,当混合溶液质量浓度为20 g/L、PMOXA-r-GMA和PAA-b-PGMA质量比为1：1时,所得涂层中羧基的含量随着PAA链长的增加而增加;异硫氰酸荧光素标记溶菌酶（FITC-溶菌酶）吸附实验结果显示,通过改变环境的pH和离子强度（I）可以调控涂层毛细管对溶菌酶的吸附和释放,在pH 7（I=10^-5mol/L）条件下,毛细管可以吸附大量的溶菌酶,当条件变为pH 3（I=10^-1mol/L）时,吸附的溶菌酶可以被释放出来。将这种具有溶菌酶可控吸附性能的涂层毛细管用于毛细管电泳在线富集溶菌酶,当PAA链长是PMOXA链长的2.2倍时,溶菌酶的灵敏度增强因子为17.69,检出限为8.7×10^-5g/L;同一天内对溶菌酶连续测定5次以及连续测定5天,峰面积的日内、日间相对标准偏差（RSD）分别为2.9%和4.1%,迁移时间的日内、日间RSD分别为0.9%和2.1%。涂层的制备只需一步,简单易行,而且涂层具有很好的稳定性。本研究为毛细管电泳分析痕量蛋白质提供了一种简单有效的方法。     

Synthesis and thermal decomposition of ditetrazol-5-ylamine

Ditetrazol-5-ylamine (DTA) was synthesized from cyanuric chloride in four steps. The thermal decomposition of DTA in the solid state was studied by thermogravimetry, volumetry, mass spectrometry, IR spectroscopy, and calorimetry. Under isothermal conditions at 200–242 °C, thermal decomposition obeys the first order autocatalytic kinetics. The kinetic and activation parameters of DTA decomposition were determined. The composition of gaseous reaction products and the structure of condensed residue were studied. The thermal effect of thermal DTA decomposition is 281.4 kJ mol⁻¹. The nitrogen content in a mixture of gaseous products formed by the reaction in a temperature interval of 200–242 °C exceeds 97 vol.%. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1660–1664, July, 2005.