Nanofibers of barium strontium titanate (BST) by sol-gel processing and electrospinning

This paper describes the fabrication of barium strontium titanate (Ba0.6Sr0.4TiO3 or BST) nanofibers by electrospinning method using a solution that contained poly(vinylpyrrolidone) and a sol-gel solution of BST. The as-spun and calcined BST/PVP composite nanofibers were characterized by TG-DTA, X-ray diffraction, FT-IR, SEM and TEM, respectively. After calcination of the as-spun BST/PVP composite nanofibers at above 700 degrees C in air for 2 h, BST nanofibers of 188+/-25 nm in diameter having well-developed cubic-perovskite structure were successfully obtained. The crystal structure and morphology of the nanofibers were influenced by the calcination temperature. Calcination at below 700 degrees C resulted in amorphous phase whereas BST with second phase such as barium titanate were formed at above 700 degrees C. Diameters of the nanofibers decreased from 208+/-35 to 161+/-18 nm with increasing calcination temperature between 600 and 800 degrees C.     

From layered double hydroxide to spinel nanostructures: facile synthesis and characterization of nanoplatelets and nanorods

Mg-Al spinel (MgAl2O4) nanorods and nanoplatelets transformed from Mg-Al layered double hydroxide (Mg-Al-LDHs) were synthesized via a combined hydrothermal method and calcination route using Al(NO3).9H2O and Mg(NO3)2.6H2O as raw materials. The nanorods and nanoplatelets were characterized by means of physical techniques, including powder X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microcopy (HRTEM), selected-area electron diffraction (SAED), Fourier transform infrared spectra (FT-IR), thermogravimetric (TG), and nitrogen adsorption-desorption isotherms. XRD patterns reveal that the Mg-Al-LDHs nanostructures were obtained under a hydrothermal reaction temperature of 200 degrees C and Mg-Al spinel nanostructures were fabricated via calcination of the Mg-Al-LDHs nanostructures at 750 degrees C. It can be seen from TEM that the sizes of the Mg-Al-LDHs nanoplatelets were about 20-40 nm and the diameters of the MgAl2O4 nanorods were ca. 6 nm. The HRTEM images indicate that the crystal lattice spaces of the MgAl2O4 nanorods and nanoplatelets are 0.282 and 0.287 nm, respectively.     

The use of alumatrane for the preparation of high‐surface‐area nickel aluminate and its activity for CO oxidation

Supported nickel has been used in a wide range of applications for industrial reactions, such as steam reforming, hydrogenation and methanation. In this work, nickel aluminate was prepared by the sol–gel process using alumatrane as the alkoxide precursor, directly synthesized from the reaction of inexpensive and available compounds, aluminum hydroxide and TIS (triisopropanolamine) via the oxide one pot synthesis (OOPS) process. Various conditions of the sol–gel process, such as pH, calcination temperature, hydrolysis ratio and ratio of nickel to aluminum, were studied. All samples were characterized using FTIR, TGA, XRD, TPR, DR‐UV and BET. The BET surface area was in the range of 340–450 m²/g at the calcination temperature of 500 °C with a mesoporous pore size distribution. Catalyst activity testing in CO oxidation reaction depended on Ni:Al ratio and calcination temperature. Higher activity was obtained from higher Ni content and lower calcination temperature. In addition, catalysts prepared using alumatrane precursor had higher percentage conversion than those prepared using aluminum hydroxide precursor. Copyright © 2005 John Wiley & Sons, Ltd.     

Thermally responsive polymeric micellar nanoparticles self-assembled from cholesteryl end-capped random poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide): synthesis, temperature-sensitivity, and morphologies

Cholesteryl end-capped thermally responsive amphiphilic polymers with two different hydrophobic/hydrophilic chain-length ratios were synthesized from the hydroxyl-terminated random poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) and cholesteryl chloroformate. The hydroxyl-terminated precursor polymers with narrow molecular weight distributions were synthesized by free-radical polymerization using 2-hydroxyethanethiol as a chain-transfer agent. The aqueous solutions of the cholesteryl end-capped copolymers exhibited reversible phase transitions at temperatures slightly above human body temperature, with the lower critical solution temperature values being 37.7 and 38.2 degrees C, respectively. The critical micelle concentration values of the two cholesteryl end-capped polymers were 9 and 25 mg/L, respectively. Polymeric micellar nanoparticles were prepared from the amphiphilic polymers using a dialysis method as well as a direct dissolution method. Transmission electron microscope studies showed that the micellar nanoparticles existed in different morphologies, including spherical, star-like, and cuboid shapes. Pyrene as a model hydrophobic compound could be readily encapsulated in these polymeric nanoparticles, at loading levels of 1.0 and 0.8 mg/g for the two cholesteryl end-capped polymers, respectively. The temperature sensitivity and unusual morphology of these novel polymeric nanoparticles would make an interesting drug delivery system.     

晶相可控的ZrO2纳米线的无卤制备及表征

采用无卤法制备晶相可控的ZrO₂纳米线. 通过静电纺丝法制备聚乙烯吡咯烷酮(PVP)与Zr(NO₃)₄的复合纤维; 再通过煅烧法在除去聚合物模板的同时制备ZrO₂纳米线. 采用X射线衍射(XRD)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 傅里叶变换红外光谱(FTIR)仪及热重差热联用热分析仪(DSC-TGA)对材料的晶相结构、 形貌及热稳定性进行表征. 通过改变煅烧温度, 可以实现ZrO₂纳米材料形貌及晶相组成的调控.     

Structure-controlled solventless thermolytic synthesis of uniform silver nanodisks

Monodisperse silver nanodisks are synthesized on the gram scale from a well-characterized layered silver thiolate precursor via thermolysis at 180-225 degrees C under a N(2) atmosphere. XRD, TEM, HRTEM, and AFM analyses indicate that the nanodisks generated at 180 degrees C over 2 h have an average diameter of about 16.1 nm (sigma = +/-12%) and a thickness of 2.3 nm (sigma = +/-14%), and they lie on their (111) faces. The disk shape is considered to be predestined by the crystal structure of the precursor. Important aspects regarding the stability of the precursor, the thermolysis temperature, and the annealing time, as well as a possible conversion mechanism, are discussed.     

Simple route to monodispersed silica-titania core-shell photocatalysts

A monodispersed silica-titania core-shell photocatalyst was synthesized via a sol-gel route without the need of pH adjustment, cationic polyelectrolytes, or surfactants in a process where silica spheres were impregnated with hydrolyzed titanium tetrabutoxide, incubated at room temperature, and then condensed using an ethanol/water (1:1) solvent. Four coating cycles in a 10% v/v titania sol produced homogeneous titania shells. The quality of catalysts was assessed quantitatively using Rietveld analysis of powder X-ray diffraction patterns combined with X-ray fluorescence spectrometry. During calcination, the anatase-to-rutile transformation was delayed to 1000 degrees C, which is approximately 300 degrees C higher than usually observed. The thermal stability and surface area of titania were enhanced through the slow crystal growth of anatase. The photocatalytic activity of the core-shell photocatalysts calcined at 400-600 degrees C was found to be proportional to the thickness of titania but did not directly correlate with the surface area.     

粒径可控球形TiO2的制备

在正丙醇与水的混合溶剂体系中以Ti(SO4)2为前驱物制备得到了粒径分布窄, 分散性好的球形TiO2. 对表面活性剂种类及用量, 反应物浓度及焙烧温度和时间等影响因素进行了研究, 结果表明, 在正丙醇与水的体积比为1:1的条件下, 以聚乙烯吡咯烷酮(PVP)为表面活性剂, 温度为70-90 ℃时可制得粒径分布窄、分散性好的高质量的球形TiO2颗粒. 通过TG-DSC、SEM、XRD等分析表明, 颗粒粒度大小及粒径分布受表面活性剂浓度和反应前驱物浓度影响大; 物相间的转化主要由焙烧温度和时间来决定. 并引入LaMer模型对颗粒形核、长大的过程进行理论说明.     

First preparation of nanocrystalline zinc silicate by chemical vapor synthesis using an organometallic single-source precursor

A method is presented to prepare nanocrystalline alpha-Zn(2)SiO(4) with the smallest crystal size reported so far for this system. Our approach combines the advantages of organometallic single-source precursor routes with aerosol processing techniques. The chemical design of the precursor enables the preferential formation of pure zinc silicates. Since gas-phase synthesis reduces intermolecular processes, and keeps the particles small, zinc silicate was synthesized from the volatile organometallic precursor [[MeZnOSiMe(3)](4)], possessing a Zn-methyl- and O-silyl-substituted Zn(4)O(4)-heterocubane framework (cubane), under oxidizing conditions, using the chemical vapor synthesis (CVS) method. The products obtained under different process conditions and their structural evolution after sintering were investigated by using various analytical techniques (powder X-ray diffraction, transmission electron microscopy, EDX analysis, solid-state NMR, IR, Raman, and UV/Vis spectroscopy). The deposited aerosol obtained first (processing temperature 750 degrees C) was amorphous, and contained agglomerates with primary particles of 12 nm in size. These primary particles can be described by a [Zn-O-Si] phase without long-range order. The deposit obtained at 900 degrees C contained particles with embedded nanocrystallites (3-5 nm) of beta-Zn(2)SiO(4), Zn(1.7)SiO(4), and ZnO in an amorphous matrix. On further ageing, the as-deposited particles obtained at 900 degrees C form alpha-Zn(2)SiO(4) imbedded in amorphous SiO(2). The crystallite sizes and primary particle sizes in the formed alpha-Zn(2)SiO(4) were found to be below approximately 50 nm and mainly spherical in morphology. A gas-phase mechanism for the particle formation is proposed. In addition, the solid-state reactions of the same precursor were studied in detail to investigate the fundamental differences between a gas-phase and a solid-state synthesis route.     

Nanofibers of LiMn2O4 by electrospinning

Through sol-gel processing and electrospinning technique, extrathin fibers of poly(vinyl alcohol) (PVA)/lithium chloride/manganese acetate composite fibers were prepared. After calcination of the above precursor fibers at 600 degrees C, the spinel lithium manganese oxide (LiMn2O4) nanofibers, with a diameter of 100-200 nm, were successfully obtained. The fibers were investigated by TG-DTA, XRD, FT-IR, and SEM, respectively. The results showed that the crystalline phase and morphology of the fibers were largely influenced by the calcination temperature.     

Surfactant mediated synthesis of spherical binary oxides photocatalytic with enhanced activity in visible light

Spherical silica and zirconia mixed titania and pure titania samples were prepared in presence of cetyltrimethylammonium bromide (CTAB) through controlled hydrolysis of corresponding metal alcoxides. Effect of surfactant amount and calcinations temperature on morphology, surface area and photocatalytic activity is studied using PXRD, SEM, FTIR, Solid state UV-vis spectroscopy and BET surface area. It is well observed that in presence of 2 mol% CTAB, uniform sized spherical oxide particles can be synthesized. However, increasing or decreasing the surfactant amount does not favor the spherical particle formation. Material synthesis in presence of CTAB not only helps in the spherical particle formation but also increases the surface area and visible light absorption. Studies on photocatalytic lead removal with respect to calcination temperature indicate that the calcination at 500 degrees C is most suitable for the best photocatalytic activity. Mixing of zirconia and silica helps in anatase phase stabilization even at 900 degrees C calcination. Accordingly low decrease in surface area even at 900 degrees C calcination is observed. Due to the phase stabilization and higher surface area binary oxide materials showed comparatively better photocatalytic activity even after calcination at 900 degrees C. So it can be concluded that present synthesis approach can produce uniform sized spherical binary oxide materials with better photocatalytic activity in visible light.     

Preparation and characterization of nitrogen-doped titanium dioxides

A type of high visible-light active titanium oxinitride(TiO2-xNx) powder was prepared by a simple proc-ess:the calcination of the hydrated titanium dioxide at the atmosphere of ammonia-argon using a tu-bular electric furnace at high temperatures. The hydrated titanium dioxide was synthesized as the precursor of TiO2-xNx using titanic acid as raw material,which came from sulfate technique of produc-ing titanium white. The effects of temperature and reaction time on the nitrogen content,grain size and crystal structure were studied. The visible-light activity and photocatalysis capability of the powder were also investigated.     

Synthesis, optical properties, and growth mechanism of blue-emitting CdSe nanorods

Blue-emitting, cubic phase CdSe nanorods with an approximate diameter of 2.5 nm and lengths up to 12 nm have been synthesized at low temperature (100 degrees C) in a single surfactant using a single-source molecular precursor. Transmission electron microscopy and dynamic light scattering measurements indicate that the nanorods are formed from self-assembly of isotropic nanoclusters. Anisotropic growth in a single surfactant appears to be favored when growth occurs below the thermal decomposition temperature of the single-source precursor.     

Preparation and characterization of ruthenium/carbon aerogel nanocomposites via a supercritical fluid route

Carbon-aerogel-supported ruthenium nanoparticles were synthesized by impregnating carbon aerogels with Ru(acac)3 or Ru(cod)(tmhd)2 from supercritical carbon dioxide (scCO2) solutions, followed by thermal reduction of these precursors. Two different carbon aerogels with pore diameters of 4 and 21 nm were synthesized. The kinetics and the thermodynamics of impregnation of carbon aerogels with the ruthenium coordination complexes were studied. The approach-to-equilibrium data indicated very fast adsorption, and the adsorption isotherms were found to follow the Langmuir model. The impregnated carbon aerogel complexes were reduced thermally at different temperatures between 300 and 1000 degrees C in the presence of nitrogen. The resulting nanocomposites were characterized using transmission electron microscopy (TEM) and hydrogen chemisorption. TEM micrographs showed that the ruthenium nanoparticles were dispersed homogeneously throughout the porous carbon aerogel matrix, and the average sizes obtained under different conditions ranged from 1.7 to 3.8 nm. Once complete decomposition of the precursor had been achieved, the mean size of the ruthenium particles increased with increasing reduction temperature.     

Effects of calcination temperature on the pore size and wall crystalline structure of mesoporous alumina

In this paper, mesoporous alumina with different pore sizes and wall crystalline structures was synthesized at calcination temperatures over 550 degrees C. The characterization of the samples calcined at 550, 800, 1100, and 1300 degrees C, respectively, was performed using TEM, XRD, FTIR, TG/DTA, and N2 adsorption/desorption techniques. The correlation between pore size and wall crystalline structure on calcination temperature was systematically investigated.     

Selective Formation of Spinel Iron Oxide in Thin Films by Complexing Agent-Assisted Sol-Gel Processing

The structure of iron oxide was controlled by regulating the hydrolytic polymerization of aquo iron complexes with organic polydentate ligands such as diols. Iron oxides were prepared by calcining the precursor polymers obtained from iron nitrate nonahydrate and diols. When the diols were 1,2-pentanediol, 1,2-hexanediol and 1,2-octanediol, α-Fe₂O₃ with corundum structure appeared exclusively or as the main crystalline phase, in spite of the amount of diol used and the calcination temperature. In the case of 1,2-decanediol and 1,2-dodecanediol, when five moles of the diols were used to one mole of iron nitrate and the calcination temperatures were below 400°C, ψ-Fe₂O₃ with spinel structure appeared as the main phase and, when less than five moles of the diols were used, α-Fe₂O₃ appeared exclusively or as the main phase, irrespective of the calcination temperature. This tendency was also observed in thin films. Thus, a transparent magnetic film composed of γ-Fe₂O₃ could be prepared by applying a benzene solution of the iron polymer, obtained with 5 equivalents of 1,2-decanediol, on quartz and calcining the gel film at 350°C.     

Spontaneous organization of uniform CeO2 nanoflowers by 3D oriented attachment in hot surfactant solutions monitored with an in situ electrical conductance technique

Uniform CeO(2) nanoflowers were synthesized by rapid thermolysis of (NH(4))(2)Ce(NO(3))(6) in oleic acid (OA)/oleylamine (OM), by a unique 3D oriented-attachment mechanism. CeO(2) nanoflowers with controlled shape (cubic, four-petaled, and starlike) and tunable size (10-40 nm) were obtained by adjusting the reaction conditions including solvent composition, precursor concentration, reaction temperature, and reaction time. The nanoflower growth mechanism was investigated by in situ electrical conductance measurements, transmission electron microscopy, and UV/Vis spectroscopy. The CeO(2) nanoflowers are likely formed in two major steps, that is, initial formation of ceria cluster particles capped with various ligands (e.g., OA, OM, and NO(3) (-)) via hydrolysis of (NH(4))(2)Ce(NO(3))(6) at temperatures in the range 140-220 degrees C, and subsequent spontaneous organization of the primary particles into nanoflowers by 3D oriented attachment, due to a rapid decrease in surface ligand coverage caused by sudden decomposition of the precursor at temperatures above 220 degrees C in a strong redox reaction. After calcination at 400 degrees C for 4 h the 33.8 nm CeO(2) nanoflowers have a specific surface area as large as 156 m(2) g(-1) with high porosity, and they are highly active for conversion of CO to CO(2) in the low temperature range of 200-400 degrees C. The present approach has also been extended to the preparation of other transition metal oxide (CoO, NiO, and CuO(x)) nanoflowers.     

一系列新的席夫碱型液晶高分子冠醚的合成与表征

以 4,4′ (α,ω 烷亚甲基二酰氧 )二苯甲醛和二氨基二苯并 1 5 冠 5为单体 ,采用溶液缩聚方法 ,合成了一类新的席夫碱型液晶高分子冠醚 .一种单体采用脂族二酰氯和对羟基苯甲醛反应制备 ,另一种新的单体采用二硝基二苯并 1 5 冠 5 ,在钯 碳催化剂存在下 ,水合肼还原制备 .合成的二硝基和二氨基 二苯并 1 5 冠 5 ,未能从IR和1 H NMR谱图上区分它们的几何异构体 .聚合物的分子量不高 ,Mn 在 1 0 1 0 0～ 1 3 0 0 0之间 .单体的结构通过元素分析、IR、1 H NMR和MS等方法确证 .聚合物的性质采用GPC、DSC、TG和POM等方法进行了研究 .发现所有的聚合物加热到各自的熔融温度 (Tm)以上都能形成液晶态 ,在液晶态可以观察到向列相的丝状织构和纹影织构 .聚合物的玻璃化转变温度 (Tg)、熔融温度和各向同性温度 (Ti)随聚合物分子中柔性间隔基的变化而变化 ,它们有较高的清亮点温度和宽的液晶态温度范围 .WAXD的研究进一步证实了聚合物的液晶性     

Spectral studies of SnO2 nanofibres prepared by electrospinning method

Tin oxide nanofibres with 100-150 nm diameter has been prepared, for the first time by calcination of poly(vinyl acetate) (PVAc)/SnO2 composite fibres prepared by electrospinning method as precursor. Scanning electron microscopic images revealed cylindrical morphology of the fibres after calcination at 600 degrees C. Both, X-ray diffraction (XRD) and Raman spectral data confirmed the presence of phase pure tetragonal rutile tin oxide after calcination process. Room temperature photoluminescence (PL) spectra of tin oxide nanofibres under excitation at 325 nm wavelength show a strong green emission at 525 nm with a band gap of 2.41 eV. FT-IR spectra confirmed the formation of pure tin oxide after calcination at 600 degrees C and complete removal of PVAc during calcination. UV-vis spectrum of the fibres showed absorption at 315 nm due to the direct electron transfer in tin oxide.     

Thermochemical decomposition of cobalt doped ammonium paratungstate precursor

The calcination is one of the important steps in the preparation of nanostructured WC and WC–Co powders from chemically co-precipitated W–Co precursors. In the present paper, the processing of the precursor prepared by co-precipitation from cobalt(II) hydroxide and ammonium paratungstate is reported. The precursor was calcined at different temperatures under various atmospheres. The resulting powders were investigated using scanning electron microscopy, X-ray diffraction, thermogravimetric analysis (TGA), differential TGA, BET, and mass spectrographic analysis techniques. The results showed that the precursor decomposes differently by calcination under different atmospheres, i.e. nitrogen, air, and helium–5% oxygen. Different decomposition behaviour was observed when the calcination was carried out at medium temperature in flowing and non-flowing air. Nanostructured powders with particle size of around 90 nm can be obtained after calcination. The precursor decomposes into CoWO₄ and WO₃ oxides at 520 °C in air after a weight loss of 10.3%.