Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Solution behavior and surface properties of carboxymethylcellulose acetate butyrate

Solution behavior of carboxymethylcellulose acetate butyrate (CMCAB) in acetone and ethyl acetate has been investigated by small-angle X-ray scattering (SAXS) and capillary viscometry and correlated with the characteristics of CMCAB films. Viscosity and SAXS measurements showed that ethyl acetate is a better solvent than acetone for CMCAB. Thin films of CMCAB were deposited onto silicon wafers (Si/SiO₂) by spin coating. AFM images revealed that CMCAB spin coated films from solutions prepared in ethyl acetate were homogeneous and flat. However, films obtained from solutions in acetone were very rough. Contact angle measurements with polar and apolar test liquids characterized CMCAB surfaces as hydrophobic and allowed estimating the surface energy of CMCAB. Sum frequency generation vibrational spectroscopy was used to understand the role played by solvents and to gain insight about molecular orientation at Si/SiO₂/CMCAB interface.     

Phase separation of polyphosphazene/poly(lactide‐co‐glycolide) blends prepared under different conditions

Using a mutual solvent technique, blend films of poly[(alaine ethyl ester)_0.62(glycine ethyl ester)_0.38]phosphazene/poly(lactide‐co‐glycolide) (PAGP/PLGA blend) were prepared at different conditions including weight ratios, solvents, environmental humidity, film thickness, and substrates. The morphology and properties of blend films were characterized by scanning electron microscope (SEM), energy dispersive spectrometer (EDX), X‐ray photoelectron spectrometry (XPS), and solvent selective etching. Compared with dichloromethane and tetrahydrofuran (THF), chloroform was the better solvent to form miscible PAGP/PLGA blend films at relatively anhydrous atmosphere. However, in the humid atmosphere, the hexagonal arrangement of holes appeared on the surface of PAGP/PLGA blend films due to the ordered array of water droplets. A sandwich‐liked structure was formed with the hydrophilic PAGP component at the top and bottom, while the PLGA component in the middle. In addition, the surface morphology of PAGP/PLGA blend films was also influenced by the film thickness and the property of the substrate. Copyright © 2010 John Wiley & Sons, Ltd.     

Solution properties of polyurethane

Polyurethane was fractionated and the fractions were characterized by gel permeation chromatography (GPC) and viscometry. The intrinsic viscosities of polyurethane in ten solvents varying in their polarity were determined and are in the order of mineral spirit < acetone < cyclohexane < cyclohexanone < xylene < ethyl benzene < toluene < benzene < methyl ethyl ketone < tetrahydrofuran. The Mark-Houwink relations suggested that solvent blend MEK: n-heptane (1:3) is a poor solvent with an a value of 0·52 and tetrahydrofuran is a good solvent with an a value of 0·78. The weight average molecular weight has been estimated by an extrapolation technique based on a linear relationship between the viscosity average molecular weight _v and the Mark-Houwink constant. The weight average molecular weights obtained from viscosity studies were used to evaluate the unpertureb dimension of the chain.     

Solubility and solution thermodynamics of 2, 6-bis (4-hydroybenzylidene) cyclohexanone in pure and binary solvents at various temperatures

Solubility of 2, 6-bis (4-hydroxybenzylidene) cyclohexanone (BHBC) in pure solvents such as 1,4-dioxane, methanol, 1-butanol, 1-propanol, ethyl acetate, acetone, tetrahydrofuran (THF), glacial acetic acid, dimethyl sulphoxide (DMSO) and binary solvents dimethyl formamide (DMF) and (1-Propanol + Tetrahydrofuran) were investigated by gravimetric method at different temperature range. The experiment solubility increases with increase in temperature in both pure and binary solvents. The Maximum solubility is found in DMF at 328.15 K and for binary solvent mixture i.e. 1-propanol and THF (0.9 mol fraction) it was maximum at 318.15 K. Further modified Apelblate and Buchowski-Ksiazczak models were used for the theoretical calculation of solubility of BHBC in pure as well binary solvents. A satisfactory correlation of these models with experimental data was observed. The solution thermodynamics parameters like enthalpies, Gibb's free energy of dissolution and entropy of solutions were calculated using Van't Hoff and Gibb's equation, which reveals the solvation mechanism is non-spontaneous and entropy driven.     

Role of solvent in the compatibility of a vinylchloride–vinylacetate–maleic acid terpolymer and nitrocellulose blends

The compatibility of cast films of a vinylchloride–vinylacetate–maleic acid terpolymer (VMCH) and nitrocellulose (NC) blends is influenced by solvents. Transparent films of VMCH/NC blends are obtained when cast from solvents such as tetrahydrofuran or cyclohexanone, whereas hazy films are obtained when cast from solvents such as acetone or ethylacetate. Visible spectroscopy and phase morphology were used to analyse the compatibility–incompatibility of the blend. Differential scanning calorimetry (DSC) studies demonstrate that the transparent film is compatible, but the hazy film is incompatible. Fourier transform infra-red (FTIR) studies establish that a greater interaction is observed between the polymer pair in case of the compatible blend than in the case of the incompatible blend. A solvent dependency of blend compatibility is reflected in this study. The conformational state of the polymers in solution, which is responsible for the compatibility phenomena, may depend on the donor number and/or Taft-β value of the solvent. The greater the donor number and/or the Taft-β value, the higher may be the level of interaction between the solvent and the polymer molecules, which in turn may give a compatible blend after removal of the solvent.     

Solubility and Thermodynamic Properties of A Hexanediamine Derivative in Pure Organic Solvents and Nonaqueous Solvent Mixtures

The solubility of N,N′-Bis(2,2,6,6-tetramethyl-4-piperidinyl)-1,6-hexanediamine in seven pure solvents (acetonitrile, acetone, methyl acetate, ethyl acetate, propyl acetate, isopropyl acetate and isobutyl acetate) and two binary solvent mixtures (acetone?+?acetonitrile and methyl acetate?+?acetonitrile) were measured from 273.15 to 303.15 K at atmospheric pressure by a dynamic method. The solubility data in these pure solvents were correlated by the modified Apelblat model, the Wilson model and the NRTL model, and that in the binary solvents mixture were fitted to the CNIBS/R–K model and the NRTL model. Furthermore, the mixing thermodynamic properties in pure and binary solvent systems were calculated and are discussed, based on the NRTL model. Finally, the applicability of the model of Zhang et al. (Ind Eng Chem Res 51:6933–6938, 2012) in correlating solubility data versus dielectric constant was extended from organic solvent–water mixtures to pure organic solvents and nonaqueous organic solvent mixtures. It was found that the dissolution behavior of a compound in the binary solvent mixtures can be predicted to some extent from those in pure solvents.     

Solution properties of poly(methyl acrylate) and (1:1) poly(styrene-co-methyl acrylate)

Poly(methyl acrylate) (PMA) and 1:1 poly(styrene-co-methyl acrylate) (PSMA) were prepared by solution and bulk polymerization, respectively. The copolymer was analyzed with NMR to ascertain its composition and microstructure. The solution properties of unfractionated PMA and fractionated PSMA in ethyl acetate were investigated by light-scattering and viscosity techniques at 35°C. Narrow composition heterogeneity as revealed from the light-scattering measurements in different solvents justified the use of a single solvent for the copolymer characterization. The equations relating the limiting viscosity number to molecular weight, the molecular dimension to molecular weight, etc., were found for homopolymer and copolymers in ethyl acetate at 35°C. In the evaluation of the Flory constant K for the unperturbed state by methods based on Flory-Fox-Schaefgen, Kurata-Stockmayer, and Stockmayer-Fixman expressions, only the first method gave a value for PMA in ethyl acetate, consistent with that obtained in other solvents, whereas similar values of K were obtained by the three methods for PSMA in ethyl acetate. The studies indicate reduced thermodynamic interaction for PSMA–ethyl acetate compared to PMA–ethyl acetate, but increased steric effect in the copolymer compared with the homopolymer.     

高分子共混物薄膜表面形貌形成过程中的溶剂效应

采用原子力显微镜观测了由四氢呋喃和2-丁酮分别作为共溶剂制备得到的聚苯乙烯/聚甲基丙烯酸甲酯(PS/PMMA)共混物薄膜的表面形貌.研究发现,溶剂效应对共混物薄膜的表面形貌有较大影响,表面形貌中凸起与凹坑的组分分布是由溶剂效应决定的,与组分比无关.溶剂对不同组分的溶解能力不同还可以导致薄膜表面相逆转点的偏移.     

High-performances membranes for pervaporation I. Poly(vinyl alcohol)–poly(N-vinyl pyrrolidone) blends

Dense membranes were prepared from poly(vinyl alcohol)–poly(N-vinyl pyrrolidone) (PVA–PVP) blends of different compositions and studied in swelling and dehydration by pervaporation of three organic solvents contaminated by 5 wt% water. The swelling generally increases with the PVP content. No extraction occurs in water–tetrahydrofuran (THF) and water–methyl ethyl ketone (MEK) mixtures. In ethanol containing 10 wt% of water, there is no extraction for blends containing less than 40 wt% PVP and an increasing extraction beyond this PVP content. The pervaporation flux of the water–ethanol mixture increases drastically at the same threshold whereas the water permselectivity falls to a low level. The values of the diffusion and permeability coefficients determined from transient permeation of the test water–ethanol mixture exhibit a similar sudden increase at the same PVP content threshold. This singular behavior of the blend membranes is interpreted by a strong affinity of the PVP component to ethanol, combined with a disappearance of crystallites in the blend at this threshold. Consequently the amorphous membrane can swell freely according to the affinity of the PVP component, leading to the observed behavior.     

Mechanism of olefin epoxidation in the presence of a titanium-containing zeolite

The effect of the nature of a solvent on the liquid-phase epoxidation of olefins with an aqueous solution of hydrogen peroxide over a titanium-containing zeolite is studied. Butanol-1, butanol-2, propanol-1, isopropanol, methanol, ethanol, water, acetone, methyl ethyl ketone, isobutanol, and tert-butanol are examined as solvents. A mechanism of olefin epoxidation with hydrogen peroxide in an alcohol medium over a titanium-containing zeolite is proposed. Epoxidation reactions involving hydrogen peroxide and different olefins are studied experimentally.     

Investigation of Hydrogen Bonded Interpolymer Complexes Based on Poly (n-butyl methacrylate–co-methacrylic acid) and Poly (n-butyl methacrylate -co-4-vinyl pyridine). Temperature Effect

Summary: Two kinds of interpolymer complexes as soluble or precipitate of different structures were obtained in both THF and butan-2-one as common solvents by monitoring the hydrogen-bonding density within homoblends of poly(n-butyl methacrylate-co-4-vinylpyridine) (BM4VP) and poly(n-butyl methacrylate-co-methacrylic acid) (BMMA). A viscometry study confirmed such differences between these two types of interpolymer complexes from the behavior of the reduced viscosity of their blend solutions with feed blend composition. Qualitative and quantitative analyses of the interactions that occurred between these copolymers of relatively bulky side chain length containing various amounts of methacrylic acid and 4-vinylpyridine were carried out by FTIR. The fraction of associated pyridine groups to the carboxylic groups of the BMMA increases as the content of these latter increases in the BMMA/BM4VP blends. The obtained results also showed that the fractions of associated pyridine within the BMMA25/BM4VP26 blends are higher than those within BMMA18/BM4VP19 or BMMA8/BM4VP10. The FTIR analysis of a selected BMMA18/BM4VP19 1:1 ratio, carried out from 80 °C to 160 °C, above the glass transition temperatures of the two constituents of the blend, confirms the presence of strong hydrogen bonding interactions between the pyridine and the carboxylic groups within these blends even at 160 °C. A LCST is expected to occur at higher temperature as shown from the progressive decrease of the fraction of the associated pyridine.     

Post‐exposure delay stability for 193 nm single‐layer photoresist: Solvent effect

We investigated the effect of post‐exposure delay (PED) for poly[2‐(2‐hydroxyethyl)carboxylate‐5‐norbornene‐co‐2‐t‐butylcarboxylate‐5‐norborene‐co‐2‐carboxylic acid‐5‐norborene‐co‐maleic anhydride] [poly(HNC/BNC/NC/MA)] resist film, which formulated with photoacid generator (PAG) under the several solvents. The solvents used in this study were propylene glycol methyl ether acetate (PGMEA), isobutyl methyl ketone (IBMK), 2‐heptanone (2‐H), and (2‐methoxy)ethyl acetate (MEA). We have introduced a new concept of rheological approach to explain the solvent effect for PED by using rheometer and light scattering equipment. In the PGMEA solvent, the resist solution shows Newtonian behavior, but the other resist solutions show shear‐thinning behavior. The resist film prepared by the shear‐thinning solvent exhibited good PED stability. In order to explain these results, we conjectured that the resist polymer existed in long‐rod shape under the specific solvent and high shear rate. Also, we could obtain 0.16 μm L/S patterns in a severely amine‐contaminated environment (about 35 ppb) after 30 min PED by using this method. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 148–153, 2000     

Determination and Correlation of the Solubility of Acetylpyrazine in Pure Solvents and Binary Solvent Mixtures

The solubilities of acetylpyrazine in seven pure solvents and one binary solvent mixture were determined by a dynamic analytic method at temperatures ranging from 268.15 to 308.15 K under atmospheric pressure. For pure solvents, the solubility of acetylpyrazine increases with increasing temperature and solvent polarity. For the binary solvent mixture of ethyl acetate and isopropanol, the solubility increases with increasing temperature and mole fraction of ethyl acetate. The solubility data were correlated with some thermodynamic models, including the modified Apelblat model, λh model, CNIBS/R-K model, and NRTL model. In addition, the relationship between solubility and solvent polarity was investigated by using the Arrhenius equation. All the models or equations gave satisfactory correlation results. The results showed that the solubility of acetylpyrazine generally rises with the increase of solvent polarity at the same temperature. Moreover, the dissolution thermodynamic properties of acetylpyrazine in different solvents were calculated and are discussed based on the NRTL model.     

Reactivity of ethyl acetate and its derivatives toward ammonolysis: ramifications for ammonolysis‐based microencapsulation process

The reactivity of three ester organic solvents toward ammonolysis was examined in relation to the development of an ammonolysis‐based microencapsulation process. Ethyl acetate, ethyl chloroacetate, and ethyl fluoroacetate were chosen as ester organic solvents. Progesterone was considered as a model drug to be encapsulated into poly‐D , L ‐lactide‐co‐glycolide microspheres. A polymeric dispersed phase was emulsified in an aqueous phase, to which ammonia was added to initiate ammonolysis. The polarization status of a carbonyl group in the backbone of the ester was found to decide the magnitude of the ester reactivity. In fact, the simple ester ethyl acetate hardly reacted with ammonia, while ethyl chloroacetate and ethyl fluoroacetate showed greater reactivity toward ammonolysis. The rapid completion of ammonolysis led to the conversion of the water‐immiscible solvents into water‐soluble solvents, thereby providing an efficient tool for microsphere solidification. Among microencapsulation parameters, the type of dispersed solvent, the molar ratio of ammonia to a dispersed solvent, and the percentage of the progesterone payload decisively influenced the characteristics of the microspheres. Subsequently, variations in such parameters accompanied considerable influence on microsphere morphology, incorporation efficiency, thermal behavior, the degree of residual solvents, and the physical status of progesterone. Optimization of the process parameters would not only contribute to improving the ammonolysis‐based microencapsulation process, but would also permit the tailoring of microsphere properties to specific demands. Copyright © 2008 John Wiley & Sons, Ltd.     

布洛芬-扑热息痛孪药的合成

以布洛芬（IPF）和扑热息痛（PCM）为原料,无水丙酮和乙酸乙酯为溶剂,二环己基碳二亚胺（DCC）为脱水剂,4-二甲氨基吡啶（DMAP）为催化剂,合成了布洛芬-扑热息痛孪药（PHI）,以重结晶法对目标产物进行纯化,产物结构经IR和1H NMR确定。 探讨了原料比例、脱水剂用量、催化剂用量、反应时间和溶媒用量对目标物产率的影响,并采用正交试验筛选最优合成工艺,最终确定的最优反应条件为:n(PCM)∶n(IPF)=1∶1.5,催化剂的最佳用量为布洛芬质量的10%,反应时间为8 h,溶媒体积为70 mL（V(乙酸乙酯)∶V(丙酮)=1∶1）,在该条件下,目标物PHI的产率为66.53%。     

Micropatterning of semicrystalline poly(vinylidene fluoride) (PVDF) solutions

Micropatterning of a semicrystalline poly(vinylidene fluoride) (PVDF) solution was performed by a temperature controlled capillary micromolding where the rate of solvent evaporation was controlled by substrate temperature. In order to choose proper solvents for micropatterning, we have investigated the solubility of PVDF in various organic solvents and crystal structures of the PVDF bulk films cast from the solvents. The films prepared from the polar solvents such as dimethylformamide (DMF), dimethyl sulfoxide (DMSO) dominantly showed γ type crystals regardless of preparation temperature, while the films from tetrahydrofuran (THF) exhibit α type crystals and the ones from acetone and methyl ethyl ketone (MEK) show the characteristics of both α- and γ-PVDF. The quality of micropatterns and shapes of the PVDF crystals in the patterns significantly depend on solvent evaporation rates. Micropatterns of PVDF formed in DMF at 120 °C showed the best uniformity in shape. Crystals of the PVDF nucleated at the center regions of microchannels tended to be elongated with the b-axis of γ-PVDF crystals along the channels as the concentration of the solution decreased. In contrast, crystals nucleated at the corner regions of the channels had their b-axis oriented perpendicular to the channels. In line patterns with the width of 2 μm, the corner nucleated crystals were dominant and a resulting bamboo-like crystalline microstructure was observed in which the b-axis of γ-PVDF crystals, fast growth direction, is oriented normal to the microchannels. The crystal structures of the bulk films and the micropatterns were characterized by X-ray diffractometer, Fourier transform infrared spectroscope in Attenuated Total Reflection mode, Polarized Optical and Scanning Electron Microscope.     

Mechanism of charge-transfer polymerization. V. Photopolymerization and photocyclodimerization of N-vinylcarbazole in the N-vinylcarbazole–oxygen–solvent system

Photochemical reactions of N-vinylcarbazole (VCZ), studied in various solvents, were profoundly influenced by the atmosphere. In the deaerated system radical polymerization of VCZ occurred in various solvents, e.g., tetrahydrofuran, acetone, ethyl methyl ketone, acetonitrile, methanol, sulfolane, N,N-dimethylformamide (DMF), or dimethyl sulfoxide (DMSO). By contrast, when dissolved oxygen was present, cyclodimerization of VCZ occurred exclusively to give trans-1,2-dicarbazole-9-yl-cyclobutane in such polar, basic solvents as acetone, ethyl methyl ketone, acetonitrile or methanol. In stronger basic solvents, i.e., sulfolane, DMF, or DMSO, simultaneous radical polymerization and cyclodimerization of VCZ proceeded, the ratio of the cyclodimerization to the radical polymerization decreasing in the order, sulfolane > DMF > DMSO. In dichloromethane, on the other hand, cationic polymerization of VCZ occurred irrespective of the atmosphere. It is suggested that oxygen acts as an electron acceptor to the excited VCZ, electron transfer occurring in polar solvents from the excited VCZ to oxygen to give transient VCZ cation radical. The effect of solvent basicity on the photocyclodimerization of VCZ is discussed.     

Dilute solution behaviour of amylose tributyrate. Light scattering,viscosity and osmotic pressure measurements in non-ideal solvents

Amylose tributyrate has been prepared and fractionated; the dilute solution behaviour of the polymer has been studied in four solvents, ethyl acetate, methyl ethyl ketone, carbon tetrachloride and tetrahydrofuran. The Mark-Houwink relations have been established for each solvent and the exponent γ varies between 0·72 and 0·86, for different solvents. Perturbed dimensions have been measured for the polymer dissolved in two solvents and an estimate of the unperturbed dimensions has been made; the latter appear to be solvent dependent. Heterogeneity corrections were applied using data established by gel permeation chromatography measurements. Values of the effective bond length b of between 17 and 19·5 × 10^?8 cm and the Kuhn statistical segment A_m of 70 to 180 x 10^?8 cm, indicate that amylose tributyrate behaves like a moderately stiff coil in good solvents, with a chain stiffness intermediate between the vinyl and cellulosic polymers.     

Synthesis and investigation of the solution behavior of graft block copolymers of polyimide and poly(methyl methacrylate)

Graft copolymers with a polyimide backbone and poly(methyl methacrylate) side chains are investigated in dilute chloroform and ethyl acetate solutions via the methods of molecular hydrodynamics and optics. Copolymer samples are prepared through the “grafting from” method via atom-transfer radical polymerization with a multicenter polyimide macroinitiator. In solutions of copolymers with low degrees of functionalization Z (40%), supermolecular structures are formed as a result of interactions between the polyimide backbones. In samples with Z → 100%, the backbone is well screened by side chains; therefore, molecular solutions are formed in both solvents. The hydrodynamic and conformational behavior of samples with high functionalization degrees changes after the transition from ethyl acetate to chloroform owing to the different thermodynamic qualities of the solvents with respect to the copolymer components. In both solvents, the backbone tends to avoid contact with a poor solvent. This effect is more pronounced in the case of ethyl acetate. Macromolecules of the studied graft copolymers are characterized by high equilibrium rigidities (>40 nm) that are 10 times higher than the corresponding characteristics of aromatic polyimides.