Pressure‐Tunable Dual‐Column Ensembles for High‐Speed GC and GC/MS

A series‐coupled ensemble of two capillary GC columns of different selectivity with an adjustable pressure at the column junction point is used to obtain tunable selectivity for high‐speed GC and GC/TOFMS. An electronic pressure controller with a 0.1‐psi step size is used to obtain numerous computer‐selected unique selectivities. System configurations for conventional, atmospheric‐pressure outlet operation with flame ionization detection and for vacuum‐outlet operation with photoionization detection are described for GC‐only experiments. Polydimethylsiloxane is used as the non‐polar column and polyethylene glycol (atmospheric outlet) or triflouropropylpolysiloxane (vacuum outlet) is used as the polar column. For GC/TOFMS experiments, 5% phenyl polydimethylsiloxane was used as the non‐polar column, and polyethylene glycol was used as the polar column. The time‐of‐flight mass spectrometer can acquire up to 500 complete mass spectra per second. Since spectral continuity is achieved across the entire chromatographic peak profile, severely overlapping peaks can be spectrally deconvoluted for high‐speed characterization of completely unknown mixtures. For mixture components with significantly different fragmentation patterns, spectral deconvolution can be achieved for chromatographic peak separations of as little as 6.0 ms. This can result is very large peak capacity for time compressed (not completely resolved) chromatograms. The use of columns with tunable selectivity allows for precise peak‐position control, which can result in more efficient utilization of available peak capacity and thus further time compression of chromatograms. The limits of tunability and deconvolution are tested for near co‐elutions of different classes of hydrocarbon compounds as well as for more multi‐functional mixtures.     

Identification of mononitropyrenes and mononitrofluoranthenes in air particulate matter via fused silica gas,chromatography combined with negative ion atmospheric pressure ionization mass spectrometry

This paper describes the use of high resolution capillary gas chromatography combined with negative ion atmospheric pressure ionization mass spectrometry (NIAPIMS) for the analysis of an air particulate extract for mononitropyrenes and mononitrofluoranthenes, some of which are powerful bacterial mutagens. The results are compared to those obtained by the electron impact mass spectrometric analysis of the same sample In addition, the NIAPIMS method confirmed the identification of 4-nitropyrene in the ambient air sample.     

CGC using a programmable electronic pressure controller

Capillary gas chromatographic separations were performed with an electronic pressure control system developed to provide precise closed-loop control of inlet pressure through the use of a solid state micro-machined pressure sensor and electronically controlled proportional valve. The closed-loop control of the electronic system provided better precision than the open-loop control achieved by manual pressure regulation. Closed-loop control can perform pressure programming, which can be combined with temperature programming to optimize separations. The pressure sensor monitors the integrity of the flow system and singals the controller to reduce flow in the presence of a sudden loss of system pressure.     

Determination of 2-methylisoborneol and geosmin in aqueous samples by static headspace-gas chromatography-mass spectrometry with ramped inlet pressure

A method for determining the earthy and musty odors 2-methylisoborneol (2-MIB) and geosmin in drinking water using static headspace-GC-MS is described. To achieve lower detection limits, split ratio was optimized with ramped inlet pressure for large headspace sampling volume. The ramped inlet pressure, which held higher pressure (higher column flow rate) only during injection, allowed us to inject 3-mL volume to GC with very low split ratio (2:1). Although sequential analysis with a stainless steel ion source often changed the mass spectrum of 2-MIB, this spectral change was eliminated by using an inert ion source with a 6 mm drawout plate. The detection limits of this method were 0.36 and 0.14 ng/L, respectively, for 2-MIB and geosmin. The repeatabilities (n = 30) were 6.6 and 4.8%, respectively, at 1 ng/L for 2-MIB and geosmin.     

Determination of thiodiglycol, a mustard gas hydrolysis product by gas chromatography-mass spectrometry after tert-butyldimethylsilylation

A method for determining thiodiglycol (TDG), a mustard gas hydrolysis product in water, serum and urine samples using gas chromatography-mass spectrometry (GC-MS) after tert-butyldimethylsilylation (TBDMS) is described. Quantitation of TDG was performed by measuring the respective peak area on the extracted ion chromatogram of m/z 293, using an internal standard, the TDG homologue, thiodipropanol, peak area of which was measured as m/z 321. The presence of salts in the sample solution not only suppressed the loss of TDG by vaporization during the evaporation of water, but also facilitated the rate of production of di-silylated derivative, bis(tert-butyldimethylsilyoxylethyl)sulfide (TDG-(TBDMS)2). Under the pretreatment conditions used, in which 0.5 ml of water sample supplemented with 100 microM potassium chloride was evaporated to dryness under reduced pressure, followed by reaction with N-methyl-N-(tert-butyldimethylsilyl)trifluoroacetamide at 60 degrees C for 1 h, TDG-(TBDMS)2 was reproducibly detected with about a 55% recovery and a limit of detection (LOD, scan mode, S/N = 3) of 5.4 ng/ml. TDG was also determined by GC-MS from a 0.5 ml serum sample (after perchloric acid deproteinization) and from a 0.1 ml urine sample, after TBDMS derivatization. The LOD was determined to be 7.0 and 110 ng/ml for serum and urine, respectively.     

气相色谱法在生物柴油生产工艺研究中的应用

综述了气相色谱法在生物柴油生产工艺研究中的应用,包括反应产物和生物柴油产品中脂肪酸甲酯含量和分布的测定,单脂肪酸甘油酯、二脂肪酸甘油酯和三脂肪酸甘油酯含量的测定,游离脂肪酸含量的测定以及微量甲醇含量的测定等。讨论了进样方式、色谱柱类型、硅烷化等因素对反应产物组成测定的影响;提出了一种采用双柱压力反吹的方式测定生物柴油产品中微量甲醇含量的方法：采用正丙醇作内标,甲醇与内标通过预切柱进入分析柱后,通过压力变化,将其余组分通过分流出口反吹出色谱系统;采用极性聚乙二醇色谱柱测定了8种不同植物油中脂肪酸甲酯的含量和分布。     

Large Volume Injection in Fast Gas Chromatography with On‐Column Injector

In this work a fast gas chromatography set‐up with on‐column injection was optimized and evaluated with a model mixture of C₈–C₂₈ n‐alkanes. Usual injection volumes when using narrow‐bore (e. g., 0.1 mm i.d.) analytical columns are ca. 0.1 μL. The presented configuration allows introduction of 10–30‐fold larger sample volumes without any distortion of peak shapes. In the set‐up a normal‐bore retention gap (1 m×0.32 mm i. d.) was coupled to a narrow‐bore (4.8 m×0.1 mm i. d.×0.4 μm film thickness) analytical column using a low dead volume column connector. The effects of the experimental conditions such as inlet pressure, sample volume, initial injection temperature, and oven temperature on a peak focusing are discussed. H‐u curves for helium and hydrogen are used to compare their suitability for high speed gas chromatography and to show the dependence of separation efficiency on the carrier gas velocity at high inlet pressures. In the fast gas chromatography system a baseline separation of C₁₀–C₂₈ n‐alkanes was achieved in less than 3 minutes.     

气相色谱法测定小麦粉中有机磷类和拟除虫菊酯类农药残留量

应用气相色谱法测定了小麦粉中4种有机磷和拟除虫菊类农药的残留量.样品中的残留农药用乙腈提取分离,所得提出液减压蒸发至近干,再用吹氮法蒸干.残渣用正己烷-乙酸乙酯(9+1)混合溶液2 mL溶解,所得溶液经中性氧化铝固相萃取柱净化.收集洗脱液,再用上述混合溶液10 mL淋洗固相萃取柱,收集洗脱液与上次洗脱液合并,减压蒸发至...     

Free release static coating of glass capillary columns; Static coating at elevated pressure — Theoretical considerations and practice

Summary Static coating of glass capillary columns has hitherto solely been carried out by evaporation of the stationary phase solvents under vacuum conditions. However, since a solvent vapour pressure higher than the external pressure is the only requirement for the vapour to flow out of the column, evacuation should not be necessary. Several important factors in the static coating procedure, such as mass (solvent vapour) — and heat transfer, heat of vaporisation of the solvent and viscosity of the stationary phase solution at elevated temperature and outlet pressure are discussed, principally to rationalise an improved static coating procedure. The alternative, so-called free-release static coating procedure, was evaluated practically by coating several columns with OV-101 and SE-30. Coating speed was found to be rapid and relatively constant whereas coating efficiency was between 80 and 100%.     

Using electronic pressure programming to reduce the decomposition of labile compounds during splitless injection

A split/splitless capillary injection port has been developed for electronic pressure programming (EPP) in gas chromatography. The inlet may be operated in several modes: constant pressure, constant flow, vacuum compensation (for gas chromatography–mass spectrometry (GC-MS)), pressure-programmed, or a combination mode enabling a pressure program to be followed by constant flow. A pressure-programming technique has been tried which uses high pressure (high column flow rate) at the time of injection followed by reduction in inlet pressure to a value required for normal chromatography. Sample is swept rapidly from the inlet and into the column, reducing contact with the hot, active inlet surfaces which cause sample decomposition. The decomposition of endrin and 4,4′-DDT, two labile pesticides, can be substantially reduced using this technique and modest improvements were also observed with the carbamate pesticide carbaryl.     

Optimizing the gas chromatographic separation and detection of polychlorinated biphenyls by use of electronic pressure programming and experimental design

The applicability of electronic pressure control and Taguchi L₂₇ experimental design to the optimization of the gas chromatographic separation and detection of polychlorinated biphenyls has been evaluated. The influence of several experimental variables, column temperature program, carrier gas pressure program, on-column injector temperature program, and make-up gas pressure program, was studied using analysis of variance. Simultaneous optimization of sample introduction, column efficiency, and detector performance could be achieved without compromising system performance. The relationships between system performance and experimental variables were established using regression analysis. Agreement between the simulated and experimental results obtained using suggested optimum conditions demonstrated the applicability of the technique developed in this study. The improvement achieved in the chromatographic separation of PCBs is presented.     

The application of two total transfer valve modulators for comprehensive two-dimensional gas chromatography of volatile organic compounds

Rotary and diaphragm 6-port 2-position valves have been evaluated as modulators for comprehensive GC. A total transfer methodology was used such that all analyte materials from the primary column were passed to the second separating column. The transfer methodology used repeated short periods of stop flow, but retained good primary column performance since primary carrier flow was partially maintained as pressure equilibrated along the length of the first column. Highly resolved separations of complex samples such as petrol and essential oils were achieved with equivalent performance (in terms of second column resolution) to thermal modulation with flame ionisation detection (FID). The valve modulators tested could outperform thermal modulators for very highly volatile organic species since the modulation process was insensitive to analyte vapour pressure. The diaphragm valve tested showed the best performance and was incorporated with a thermal desorption system to provide a high sensitivity separation of volatile organic compounds (VOCs) in air with LODs for individual VOCs of 2-4 pptV for a 1-L air sample.     

Free release static coating of glass capillary columns; rapid coating at lower temperatures and elevated pressures

The coating speed upon static coating of glass capillary columans was evaluated in terms of inner diameter and length of the column, viscosity and pressure of solvent vapor, etc. From the equation obtained it can be shown that a smaller diameter of a microbore column restricts solvent vapor transfer to the orifice of the column drastically. To compensate for this restriction, a higher pressure at the meniscus is needed. As an alternative to using a higher coating temperature, application of more volatile solvents such as n-butane and isobutane is proposed. Several glass capillary columns (130 μm i.d.) were coated with SE-54 dissolved inpentane-acetone mixed with n-butane or isobutane and the column performances were evaluated. Selection of these solvents permitted free release static coating of ca. 100 μm columns at lower or even ambient temperatures and they were equally suitable as commonly applied solvents (e.g. pentane) to coat highly efficient columns.     

Preparation and evaluation of nickelmesogen for micropacked gas chromatography

The preparation and mesomorphic properties of a substituted bis(dithiolene)nickel complex derived from 4, 4'-dimethoxybenzil are reported. The phase transition temperatures were based on data obtained by polarized light microscopy and differential scanning calorimetry. The mesogenic phase existed over the temperature range from 77 to 175 degrees C. A novel micropacked column (1.5 or 3 m x 1 mm i.d.) prepared from the slurry of bis[1,2-bis(4-n-undecyloxyphenyl)ethane-1,2-dithiolene] nickel(II) (5%, w/w), coated on Chromosorb W was applied for the separation of dialkyl sulfides. The non-linearity (discontinuity) of Van't Hoff plots suggests that the liquid crystal property existed even in the coated phase. Factors affecting the retention and the sample selectivity on the prepared column were examined by using a flame photometric detector (FPD). The separation might be based on the mechanism of ligand exchange, shape selectivity and polarity interaction besides the vapor pressure. LOD for the determination of dialkyl sulfides was below 1 ng for most of the analytes.     

超临界CO2萃取香草兰化学成分分析

香草兰 ,学名 :ＶａｎｉｌｌａｐｌａｎｉｆｏｌｉａＡｎｄｒ.,又名香荚兰 ,香子兰 ,属兰科香子兰属 ,是一种名贵的多年生热带藤本植物 ,有独特的香味 ,被称誉为“食品香料之王”。香草兰经加工后 ,是食品工业的重要天然香料 ,也用于烟草业、化妆品业和药物[1,2 ] 。香草兰原产于墨西哥 ,主产国还有马达加斯加、印尼、牙买加等[3 ] 。近年来 ,我国海南、云南等地也大力种植和推广。超临界流体萃取 (ＳｕｐｅｒｃｒｉｔｉｃａｌＦｌｕｉｄＥｘｔｒａｃｔｉｏｎ ,简称ＳＣＦＥ)是近 2 0年发展起来的现代提取分离技术 ,具有工艺简单、成本低、…     

Gas chromatography on 10 um silica particles

Summary Porous silica microparticles designed for modern liquid chromatography have proven effective in gas chromatography. Columns of 35–50 cm gave plate heights as low as 3.3 particle diameters and speeds of 2400 theoretical plates per second or 500 effective theoretical plates per second. Inlet pressures up to 70 atmospheres were required using hydrogen as carrier gas. The particles as received were too retentive for fast chromatography and gave asymmetric peaks. A coating of fluorosilicone oil overcame both problems. Other coatings were less effective. Bonded phases proved less satisfactory on both counts and also gave substantially less efficient columns and greater flow resistance. Column efficiency and flow resistance were sharply dependent on physical properties of the particles. The most efficient packing was clearly spherical particles of 5–10 μm diameter with narrow size distribution, pore diamters about 50 nm, BET surface areas of 25–50 m²/g and surfaces modified with trifluoropropyl silicone. A six-component hydrocarbon sample was separated in 33 s with a resolution of 4 for the most difficult pair and in 2.6 s with a minimal resolution. Performance was limited by end effects and by available pressure so that much better performance can be expected from longer columns and higher pressures.     

Device for filling of small diameter capillaries with stationary phase solutions in liquefied gases

This paper describes a high pressure device for filling small diameter capillaries with stationary phase solutions is described. A liquid is forced into the capillary column with the help of high pressure syringe whose needle (provided with a side opening) is tightened in a PTFE seal. The device allows use of liquefied gas as solvent. A detailed procedure is given for filling the capillary with stationary phase solution. The performance of the device was evaluated by filling 12 m × 15 μm i. d. glass capillary with 6.5 % (w/v) SE-54.     

Determination of the volatiles from tobacco by capillary gas chromatography with atomic emission detection and mass spectrometry

A new gas chromatograph‐atomic emission detector (GC‐AED) coupled with Deans switching technique for analyzing volatiles from tobaccos were developed. The detector operating parameters (reagent gas pressure and make‐up gas flow rate) were optimized. The detection limits for the elements carbon (193 nm), hydrogen (486 nm) and oxygen (171 nm) ranged 0.05–0.2, 0.05–0.3 and 1–11 ng, respectively, depending on the compound. The sensitivity and linearity for the elements carbon (193 nm), hydrogen (486 nm) and oxygen (171 nm) decreased in the order O>H>C. Calibration curves were obtained by plotting peak area versus concentration, and the correlation coefficients relating to linearity were at least 0.9359. Elemental response factors measured on these channels, relative to the carbon 193‐nm channel, were hydrogen, 0.38–0.48 (mean %RSD=5.64), and oxygen, 0.085–0.128 (mean %RSD=14.9). The evaluation was also done for the new technique and for an established GC‐MS technique for the same real samples. The results of GC‐AED and GC‐MS showed that there was a relatively good agreement between the two sets of data.     

Optimization of a GC‐MS/MS Method for the Analysis of PCDDs and PCDFs in Human and Fish Tissue

This paper outlines the possibilities of selectivity and sensitivity enhancement in measuring PCDD/F congeners using an ion trap GC‐MS/MS. The pressure of the collision gas and the collision energy were optimized. The modified GC‐MS/MS method was applied to the determination of PCDDs and PCDFs in human and fish tissues. Limits of quantification were about 1 pg/g of fat for all seventeen 2378 PCDD/Fs tested (starting amount of fat, 2 g).