Modification of the polytrimethylsilylpropine adsorption layer in open capillary columns

Modification of adsorption open capillary columns coated with polytrimethylsilylpropine (PTMSP) was experimentally studied. The modification of PTMSP by solvents (chlorobenzene, pentanol) and hot ethanol improves (up to 40%) the efficiency of capillary columns with a slight (3—7%) decrease in the retention factor.     

Stimultaneous quantitative analysis using dual capillary columns of different polarities

Complex organic mixtures, such as coal liquefaction and oil shale products and by-products, are comprised of hundreds or thousands of individual components. State-of-the-art high resolution gas chromatography does not always provide sufficient resolution to allow accurate quantitation or identification of many compounds of interest. The concept of dual capillary column chromatography combines the different resolving characteristics of two capillary columns coated with different stationary phases into a single chromatographic run. In this approach, both columns are connected to the same injection port. Analysis of complex mixtures in this fashion can confirm the identification and quantitation of components on two columns of different polarity with little increased analysis time, can provide a means of obtaining quantitative data for individual components which are known to coelute on any one column, and can alert one to unknown coelution problems that would be undetected by gas chromatographic analysis on a single capillary column. Simultaneous dual column analysis was applied to three samples, the neutral polycyclic aromatic hydrocarbon (PAH) fraction of a Solvent Refined Coal-II (SRC-II) heavy distillate, the nitrogen-containing polycyclic aromatic compound (N-PAC) fraction of an SRC-II heavy distillate, and the basic fraction from a shale oil process water. Fused silica capillary columns coated with SE-54 and Durawax 3 were used for the analyses of the heavy distillate, while SE-54 an Carbowax 20M capillary columns were used for the analysis of the process water.     

Separation of alicyclic and aromatic hydrocarbons on a PLOT column coated with 3-benzylketoiminepropyl group

An interpretation of specific electron-donor-acceptor interactions between the adsorbent coating the walls of a capillary column and adsorbates from the groups of alicyclic and aromatic hydrocarbons is proposed. The adsorbent was based on silica the surface of which was modified with silane containing 3-benzylketoimine groups to improve its adsorption properties. The columns studied had walls coated with 3-benzylketoimine groups, and Cu(II) chloride complexes or with Ni(II) chloride complexes. The adsorbate-adsorbent interactions were interpreted on the basis of the Kovats retention index, specific retention volume, molecular retention index, and ??M _e values. The influence of particular elements of spatial structure and the positions of double bonds in the adsorbate molecule was evaluated on the modelling calculations based on the quantitative structure-retention relationships. The introduction of transition metal ions in the form of complexes into the adsorbents studied increased the strength of the interactions between the adsorption layer of the capillary column and the adsorbate molecules. The increased strength of the interactions was accompanied by increased selectivity of the columns with regard to a group of alicyclic and aromatic hydrocarbons. The analytical performance of the columns thus obtained was compared with that of a commercial column coated with the 100 % dimethyl polysiloxane phase.     

Comparison of surface modification techniques used for the preparation of wall coated open tubular glass capillary columns

Summary Comparison of different techniques for modifying internal glass surfaces to accept a substrate loading on wall coated open tubular columns (WCOT) were examined. Inner surfaces pretreated with a non-extractable Carbowax 20M layer, barium carbonate and silica whiskers were prepared and coated with a Carbowax 20M liquid phase. The columns were evaluated for efficiency, acidic-basic and adsorption properties, thermal stability and coating efficiency. Column performances were also assessed for deactivated surfaces. Each column was applied to a standard mixture of Aroclor 1016.     

一种新型超支化聚酯物理吸附涂层毛细管电泳柱的制备及其对碱性蛋白质的分离

采用一步法和准一步法合成了以季戊四醇为核的两个系列的超支化聚酯,利用红外光谱、羟值测定等手段对分子结构进行了表征。利用超支化聚合物低粘度的特点,用物理吸附方法将其涂于毛细管电泳柱内壁,使其在毛细管内壁上形成稳定的超支化聚酯涂层。该涂层在pH 3.0~7.0范围内能够有效地抑制电渗流和蛋白质在毛细管壁上的吸附,在pH 5.0的缓冲液中分离碱性蛋白质时,分离柱效可达105塔板/m,具有良好的分离效果。     

Preparation and evaluation of polar stabilized phase open tubular (SPOT) columns

Summary A method is described for the routine preparation of high resolution stabilized phase open tubular (SPOT) columns. A finely dispersed siliceous material (Cab-O-Sil) is treated with benzyltriphenylphosphoniumchloride and dynamically coated onto the inside wall of glass capillary columns. Additional dynamics coating with a polar stationary phase yields thermostable columns of high efficiency. The columns show favourable adsorption properties and good long term stability. The mechanical stability of the stationary phase film is explained in terms of the rheological behaviour of concentrated disperisons. The designation PLOT columns appers inapplicable, and these columns will be referred to as SPOT columns. A theoretical model, describing band spreading in SPOT columns, is proposed and compared with the experimental results. Some applications in routine use and in ultra trace analysis are presented.     

Gas chromatographic analysis of estrogens from pregnant mares' urine using glass capillary columns

Glass capillary columns coated with OV-225 and Silar 10C were used to analyze estrogens (as their trimethylsilyl derivatives) present in pregnant mares' urine. Such columns provide better resolution in a shorter time than the corresponding packed columns, as exemplified by the separation of estrone from equilin.     

Adsorption and biotransformation of 17β-estradiol in biological activated carbon adsorbers

As the first systematic study dealing with the adsorption of estrogens by granular activated carbon (GAC), the removal behavior of 17β-estradiol (E2) and its biotransformation product of estrone (E1) in fixed GAC columns was examined using four biological activated carbon (BAC) columns (BAC-1～BAC-4) generated by coating four GAC columns with detached microorganisms from the riverbed sediment of a representative drinking river water source containing lower content of natural organic matter (NOM). For comparison, parallel adsorption experiments were also performed using another four GAC columns (GAC-1～ GAC-4) packed by strictly following the configurations of four BAC columns. Adsorption experimental results obtained by intermittently spiking E2 over a total running period about 350 days into the river water mixed with or without a peaty water containing higher content of NOM showed that E2 was readily removed by adsorption and the combined adsorption/biodegradation. The vertical profiles of E2 and E1, which have great significance for better understanding and optimization of the adsorption process for removal of human estrogens, were also obtained.     

Perfusion chromatography: Effect of micropore diffusion on column performance in systems utilizing perfusive adsorbent particles with a bidisperse porous structure

A mathematical model describing single-component and multi-component adsorption in columns with bidisperse perfusive or bidisperse purely diffusive adsorbent particles is constructed and presented. The model is used to study the adsorption of lysozyme onto monocional anti-lysozyme in columns with bidisperse porous adsorbent particles. The influence of the effective pore diffusion coefficient of the adsorbate in the microparticles (microspheres) and the effects of particle size and intraparticle convective flow on column performance are examined. The results for the systems studied indicate that the systems with bidisperse perfusive particles provide a higher dynamic utilization of the adsorptive capacity of the column than the systems having bidisperse purely diffusive particles.     

Selective retention of explosives and related compounds on gas-chromatographic capillary columns coated with lanthanide(III) β-diketonate polymers

The purpose of this research was to investigate coating capillary columns with lanthanide(III) β-diketonate polymers to provide gas-chromatographic columns with selectivity toward explosives and related compounds. Capillary columns were statically coated with a mixture of a lanthanide(III) β-diketonate polymer, which utilized p-di(4,4,5,5,6,6,6-heptafluoro-1,3-hexanedionyl)benzene (dihed) as a ligand, and SE-30. A novel coating technique was developed that used a methanol-containing azeotrope to provide solubility for both polymers while maintaining a low boiling point compatible with static coating. As based on temperature-programmed retention indices, the experimental columns displayed selective retention of nitroaromatic, nitroalkane, and nitrate ester test probes relative to an appropriate SE-30 control column. Selective retention was more pronounced for strongest Lewis base analyte contained in the test mixture (i.e., cyclohexanone). Relative analyte retention on the La(dihed), Tb(dihed), and Eu(dihed) columns are discussed relative to Lewis acidity and solubility of the polymer in the azeotropic coating solution.     

Polyimide polymer glass-free capillary columns for gas chromatography

Polymeric polyimide capillary tubing, both uncoated and coated with stationary phases of two polarities, is explored for use as capillary columns for gas chromatography (GC). These glass-free polyimide columns are flexible and their small winding diameter of less than a cm around a solid support makes them compatible for potential use in portable GC instruments. Polyimide columns with dimensions of 0.32 mm i.d. × 3 m are cleaned, annealed at 300°C, and coated using the static method with phenylmethylsilicone (PMS). Separations of volatile organics are investigated isothermally on duplicate sets of polyimide columns by GC with a flame ionization detector using split injection. Unlike the uncoated ones, the coated polyimide columns successfully separate Grob test mix classes of alkanes, amines, and fatty acid methyl esters. The relative standard deviations for retention time and peak area are 0.5 and 2.5 , respectively. With the 3 m PMS-coated column connected to a retention gap to permit operation at its optimum flow rate of 30 cm/s, a plate count of 3200 or plate height of 1 mm is possible. Lack of retention and tailing peaks are evident for the polyimide polymer capillary columns as compared to that of a 3 m commercial cross-linked PMS fused silica capillary. However, headspace analyses of an aromatic hydrocarbon mix and a Clearcoat automotive paint sample are viable applications on the PMS polyimide polymer column.     

Whisker surfaces in (GC)2

Growing whiskers on the inner wall of glass capillary columns is an easy roughening technique which allows efficient coating of the columns with any stationary phase. The advantages and disadvantages of whisker surfaces are discussed. Several examples are presented to illustrate the possibilities of whisker-wall coated open tubular (WWCOT) columns.     

Factors affecting the capillary electrophoresis of ricin, a toxic glycoprotein

Conditions for the analysis of ricin with capillary electrophoresis were investigated. Uncoated and coated columns were tested with a variety of different buffer combinations which included different principal components, pH, ionic strength, and additives. Of the combinations tested, uncoated columns used with either zwitterionic salts or putrescine gave the best results. Multiple peaks were resolved with these conditions. Coated columns generally yielded between 1000 and 5000 plates with several buffer combinations. Ricin may be analyzed faster and with greater resolution with capillary electrophoresis employing untreated fused-silica columns than by using other chromatographic techniques.     

Selectivity differences between sol-gel coated and immobilized liquid film open-tubular columns for gas chromatography

The solvation parameter model is used to determine the system constants for two sol-gel coated open-tubular columns at five equally spaced temperatures in the range 60-140 degrees C. Differences in the system constants as a function of temperature are used to determine the affect of sol-gel structure on the selectivity of SolGel-l and SolGel-Wax columns compared with conventionally coated and immobilized poly(dimethylsiloxane) and poly(ethylene glycol) stationary phases. The sol-gel columns should be suitable for similar separations to those presently performed on conventional immobilized liquid film columns of the same type but selectivity differences for polar compounds, which depend on temperature, should be anticipated.     

Ion chromatography on reversed-phase materials coated with mixed cationic and nonionic surfactants

Columns suitable for use in anion chromatography can be prepared by coating a packed reversed-phase HPLC column (C18 silica or polystyrene particles) with a cationic surfactant. The efficiency is improved dramatically by first coating the column with a nonionic surfactant and then subsequently with the cationic surfactant. The thickness of the first coated layer as well as the chemical structure of the surfactant have a major effect on the column performance. Actual separations are included to demonstrate the convenience and practical use of the coated columns. Using this approach, columns with 12,900 theoretical plates for the 15-cm column (or 86,000 plates/m) were produced, giving well shaped peaks with an average asymmetry factor of 1.09. The coated layers were found to be stable, giving retention times with an average relative standard deviation of 1.6% for 12 consecutive runs.     

Gravity-flow open tubular cation chromatography

We describe ion chromatography (IC) on open tubular cation exchange columns with a controllable capacity multilayered stationary phase architecture. The columns of relatively large bore (75 microm id) are fabricated by coating fused-silica capillaries with multiple layers of poly(butadiene-maleic acid) (PBMA) copolymer and crosslinking the deposited layers by thermally initiated radical polymerisation. Column capacity increases in a predictable manner with increase in the number of successively coated layers. Gravity flow with a modest head (< 2 m) can provide the desired separations within a reasonable period. We provide a minimalist configuration where no suppression is used, the sample is injected hydrodynamically as in CE, and detection is accomplished by an inexpensive homebuilt contactless conductivity detector or a capacitance to voltage digital converter. A 1 m long 75 microm bore column coated with two layers of PBMA allows gravity-flow open tubular IC to separate four alkali cations in < 10 min with a 1 mM tartaric acid (TA) eluent. Simultaneous separation of alkali and alkaline earth metal cations can be accomplished in less than 25 min using 1.75 mM pyridinedicarboxylic acid as an eluent. Contactless conductometric detection (C(4)D) allows LODs down to 150 nmol/L, corresponding to 30 fmol injections. Analysis of real water samples is demonstrated.     

Flexible soft glass capillary columns vs. flexible fused silica capillary columns for gas chromatography-a critique

The gas chromatographic use of flexible thin walled soft glass capillary columns coated with non-polar stationary phases is compared to similar columns made of fused silica glass. With non-polar soft glass columns, the use of surface roughening viagaseous HCI followed by a Carbowax 20 M pretreatment gave adsorptive phenomena, and thermal instability. With very polar soft glass columns where a variety of cyanopropyl silicone phases were coated directly onto the NaCI crystal matrix, adsorptive effects were again prominent and frequent break-down in film stability with time, was also observed. These undesirable effects were due to the presence of metal oxides in the soft glass. Attempts to remove these materials from the thin walled soft glass surface by means of acid leaching produced significant brittleness. This deleterious result was further increased by attempts at high temperature silylation or polysiloxane deactivation. In sharp contrast, the fused silica surface was essentially free of metal oxides and the surface silanol groups are easily neutralized by silylation or polysiloxane deactivation techniques. No brittleness was observed following these procedures. An increasing series of high molecular weight, viscous, polymeric vinyl containing non-polar and highly polar stationary phases have been produced which readily wet the surface of the fused silica and are easily crosslinked in the presence of free radical generators. These columns are essentially free of all the problems noted with flexible thin walled soft glass. When all of the parameters involved in the fabrication of a glass capillary column are assessed, it appears at this time, that the flexible fused silica glass column with cross linked phases approaches the “ideal” capillary column.     

Evaluation and application of liquid chromatographic columns coated with 'intelligent' ligands: (I) acylcarnitine column

Unique stationary phases of octadecylsilica (ODS) coated with acylcarnitines have been developed for liquid chromatographic columns. The ODS column coated with acylcarnitine was readily prepared by recycling the solution containing acylcarnitine through an ODS column in a closed loop. Acylcarnitine was adsorbed on the ODS surfaces by hydrophobic interaction between the acyl group of acylcarnitine and the octadecyl group of the ODS phases. The ODS column coated with stearoylcarnitine (CN-18 column) was the most stable among the four columns coated with acylcarnitines of various acyl chain lengths (decanoylcarnitine, lauroylcarnitine, myristoylcarnitine, and stearoylcarnitine) under the condition of delivery of the mobile phase, indicating that adsorption of acylcarnitine on the ODS surfaces depended on the length of acyl chains. The CN-18 column was usable for delivering the mobile phase contained less than 20% (v/v) acetonitrile, retaining almost the same separation efficiency as the intact ODS column. The retention behavior of ionic solutes on the CN-18 column could be explained by both ionic and electrostatic interactions between the solutes and the stationary phase. The CN-18 column enabled efficient separation of inorganic anions, nicotinic acids, amino acids, and nucleotides. The chiral ODS column coated with enantiomer of stearoylcarnitine, L-stearoylcarnitine (L-CN-18 column) could achieve direct enantiomeric separation of DL-tryptophan, alpha-methyl-DL-tryptophan and DL-3-indolelactic acid using 100% water as the mobile phase. The L-CN-18 column could also separate enantiomers of amino acids and alpha-hydroxycarboxylic acids by ligand-exchange chromatographic mode using a mobile phase containing copper(II) ion. The chiral recognition is discussed for enantiomeric separation on the L-CN-18 column.     

交联聚丙烯酰胺毛细管电泳涂层柱的制备及其应用

摘要建立了一种简便的制备交联聚丙烯酰胺型毛细管电泳涂层柱的方法. 所制备的涂层柱能够有效地抑制电渗流及蛋白质在管壁上的吸附. 考察了碱性蛋白质在pH=4。0的缓冲溶液中的分离, 迁移时间重现性误差小于2。1%. 对麻黄提取物中的生物碱进行了分离, 平均理论塔板数为24×105 plates/m.     

A homochiral porous organic cage with large cavity and pore windows for the efficient gas chromatography separation of enantiomers and positional isomers

Porous organic cages composed of discrete cage molecules have attracted considerable recent attention as gas adsorption materials and separation media. In this study, we report a homochiral porous organic cage CC5 with a large cavity and pore windows as a novel stationary phase for high‐resolution gas chromatographic separations. The capillary column was prepared by a static coating method. A large number of racemic compounds have been resolved on the coated capillary column, including derivatized amino acids, alcohols, alcohol amines, esters, ethers, ketones, and epoxides. It is interesting that the CC5‐coated capillary column exhibits significant chiral recognition complementarity to a commercial β‐DEX 120 column and a previously reported homochiral porous organic cage CC3‐R‐coated column, which could expand the range of the analytes amenable to separation on porous organic cage‐based capillary columns. Moreover, the fabricated column also shows excellent selectivity for the separation of positional isomers, including the challenging ethylbenzene and xylene isomers. Experimental results demonstrate an excellent separation performance and stability of the CC5‐coated column, making it promising for gas chromatography applications.