Fast self-absorption correction procedure for low energy 210Pb gamma emission in environmental samples

Gamma ray spectrometry is a convenient method to determine the concentration of 210Pb in environmental samples. It normally requires corrections for self-absorption of gamma rays, as environmental samples often differ in composition from each other and from the calibration standards. The procedure proposed, based on the use of a special shaped source for the absorption measurement, is more accurate than the conventional point source and, at the same time, as simple and quick.     

AB initio derivation of formulations for210Pb dating of sediments

Basic formulations used in the sedimentary²¹⁰Pb dating technique are derived from fundamental considerations. The formulations are applicable to models that assume either a constant rate of supply (CRS) of unsupported²¹⁰Pb to the sediments or a constant initial concentration (CIC) of this²¹⁰Pb in the sediments. A previously proposed expression linking age discrepancy to mass sedimentation rates afforded by the two models is found to be inadequate in explaining the observed discrepancy between the CIC and CRS ages of segments of an undisturbed sediment core. It is noted that this age discrepancy is attributable to the mathematical treatment of data in the two models. A new expression, relating age discrepancy to the fluxes of unsupported²¹⁰Pb obtainable by the two models, is derived and found to give more accurate and consistent results.     

A practical and accurate method for the determination of 234Th simultaneously with 210Po and 210Pb in seawater

A practical technique has been developed for the determinations of (234)Th simultaneously with (210)Po and (210)Pb in seawater samples, which greatly simplifies the on-board chemical procedures and enables an accurate correction of (234)Th ingrowth. A unique feature of this technique lies in the exact determination of co-precipitated (238)U following Fe(OH)(3) precipitation which leads to an exact correction of ingrown (234)Th between Fe(OH)(3) precipitation and U/Th separation. Such a correction eliminates several cumbersome on-board chemistry steps (such as Po plating, Fe(2+) oxidation, and 9 N HCl anion exchange) required in regular procedures to eliminate the (234)Th ingrowth. The total time required for on-board sample treatment (spike equilibration, Fe (OH)(3) co-precipitation and filtration) could be less than 10 h which significantly increases the sample processing efficiency and data throughput.     

A method for the correction of self-absorption of low energy photons for use in routine INAA

Practical application of oow energy gamma rays and X-rays in I.N.A.A. was restricted because of the complexity of the X-ray spectrum and sample self-absorption. This paper describes a method for the calculation of sample self-absorption on the basis of the actual sample spectra only, as measured with a high resolution semiconductor X-ray detector. In the 20–400 keV energy range, the attenuation coefficient can be represented by a three parameter function of photon energy. This was verified by measuring the transmission of photons of different energies through a range of materials. Experiments with neutron irradiated U.S.G.S. standard reference materials with known major oxide composition showed that self-absorption thus calculated from the observed spectra is in good agreement with the results of theoretical calculations based on known attenuation coefficients.     

Levels of 210Po and 210Pb in cigars

²¹⁰Po and ²¹⁰Pb concentrations have been determined in 58 cigar brands manufactured in 11 countries. Cuban and American cigars showed the lowest ²¹⁰Po content. The mean levels of ²¹⁰Po in Brazilian, European and Dominican cigars were almost identical and somewhat lower than the levels observed for cigars from other Latin American countries. Cuban, American and European cigars contained low levels of ²¹⁰Pb. Cigars from the remaining countries contained twice as much ²¹⁰Pb. The mean ²¹⁰Po/²¹⁰Pb ratio showed an excess of polonium. In the case of a one cigar-a-day smoker, the calculated annual absorbed dose due to ²¹⁰Po is -16 mGy.     

A rapid method for the separation of 210 Po from 210 Pb by TIOA extraction

A rapid method for the separation of ²¹⁰ Po from ²¹⁰ Pb was developed utilizing extraction of triisooctylamine (TIOA)/xylenein HCl+H₂O₂ medium. Polonium in the form of PoCl ₆ ²– was extracted into TIOA phase and ²¹⁰Pb remains in the aqueous phase. Lead-²¹⁰ was determined by -countingof its granddaughter, ²¹⁰ Po ingrown from ²¹⁰ Pb forsome period of time. Distribution of ²¹⁰ Po and ²¹⁰Pb in TIOA and aqueous phases was investigated in various concentrations ofHCl media. Hydrogen peroxide was used to further decompose organic matterand to remove sulfur to prevent its deposition on the silver disc. The improvedprocedure resulted in a good chemical yield (80–95%) and a good á-resolution.     

On the method of Dryak et al. for self-absorption correction calculations

An analytical expression for the equivalent thickness of a sample measured in a Marinelli geometry is reported. Using it as input in the formula proposed by Dryak et al.¹, self-absorption corrections for Marinelli beakers with arbitrary dimensions can be computed.     

Radiochemical determination of210Po and210Pb in water

A method for²¹⁰Po and²¹⁰Pb determination in water samples is described. The nuclides are concentrated, in presence of added²⁰⁸Po and lead carrier, by evaporation. Then the polonium is plated electroless from the acidic solution on a copper planchet and measured by alpha spectrometry.²¹⁰Pb separation from the other isotopes is based on the solutility of PbSO₄ in citrate.²¹⁰Pb content is determined by measuring the activity of its daughter²¹⁰Bi. The critical steps in the isolation of lead have been examined and discussed.     

A substoichiometric radioisotope dilution study using210Pb

A radioisotope dilution procedure has been developed which permits the determination of lead over a concentration range of 0.1 to 10 ppm. Samples in an ammoniacal cyanide/sulfite medium are labelled with²¹⁰Pb, followed by addition of substoichiometric amount of dithizone. The Pb/HDz/₂ formed is extracted into CH₂Cl₂, and aliquot portions are taken for liquid scintillation counting. Count rate is plotted vs. the reciprocal of the lead concentration, yielding a straight line. An average error of ±3.5% is estimated, based on a linear least squares fit.     

Chemical characterization and 210Pb dating in wetland sediments from the Nhecolândia Pantanal Pond, Brazil

Summary Pantanal, located in the central region of South America, is recognized as one of the world's largest freshwater wetlands. In order to verify possible changes in this environment, a study was undertaken in Nhecolandia Pantanal, Mato Grosso do Sul State, Brazil. Two sediment cores from the Salina do Meio pond (SM1 and SM2) and one core from a small flood land named Baía (B5) were collected in 2001. The elements As, Ba, Br, Ce, Co, Cr, Cs, Eu, Fe, Hf, La, Lu, Na, Nd, Rb, Sb, Sc, Sm, Ta, Tb, Th, U, Yb, Zn and Zr were determined by instrumental neutron activation analysis (INAA). Cluster and factorial analysis were applied to the chemical data. The sedimentation rate in the SM2 core was determined by ²¹⁰Pb method and the mean value found was 0.61 cm ^. y^-1. The results obtained in the present study showed that recent geochemical processes such as desorption, precipitation and dissolution can contribute for the high water alkalinity and salinity in the saline ponds.     

Determination of 210Pb, 210Bi and 210Po in natural drinking water

A new method for the radioanalytical determination of the ²²²Rn progenies ²¹⁰Pb, ²¹⁰Bi and ²¹⁰Powill be presented, which has been improved for analyses of water samples fromdifferent regions in Austria. 1–2 liter samples were taken in polyethylenebottles prefilled with conc. HNO₃ to obtain 0.2M acidic solutions,thus avoiding adsorption effects. After adding 1.6 mg of inactive lead carrier,the water sample was evaporated to dryness, converted to the chloride formand dissolved in 1M HCl.     

Measurements of210Pb and210Po in Japanese human hair

²¹⁰Pb and²¹⁰Po in human hair have been measured to serve as an aid in order to estimate the dietary intake and body burden of these radionuclides of Japanese. The²¹⁰Po concentrations found in 83 hair samples were ranging from 4.0 to 59.3 mBq/g with a mean (median) value of 18.2±12.2 (14.9) mBq/g as compared to the²¹⁰Pb concentrations from 0.7 to 6.5 mBq/g with a mean (median) value of 2.3±1.1 (2.0) mBq/g. The²¹⁰Po/²¹⁰Pb activity ratios (mean: 8.7±5.1, median: 7.1) were surprisingly higher compared with the available literature value of about 2. The high concentration of²¹⁰Po in human hair of Japanese may be due to the ingestion of animal protein mainly in the form of seafood.     

A simple method for self-attenuation correction in <Superscript>210</Superscript>Pb activity measurement in a well-type HPGe detector

A simple method for ²¹⁰Pb determination in a well-type detector for matrix with apparent densities ranging from ρ = 0.430 g cm^?3 to ρ = 2.037 g cm^?3 is presented. Ten spiked samples of ²¹⁰Pb were prepared to obtain the detector efficiency as a quadratic function of the matrix density. Then this equation was validated and successfully used to measure ²¹⁰Pb concentration activity in other samples. The equation proposed in this work is specific for each germanium detector; however it is proposed an extrapolation of the method to other well-type germanium detector by preparing a spiked sample and determining the efficiency for ²¹⁰Pb.     

A bone ash standard for90Sr,210Pb,210Po,uranium and the actinides

Possibilities and problems of experimental differentiation of two chemical or particle forms of element M (Acentral atom or group, Bcomplex, metalorganic or bioinorganic species, colloid, etc.) between which mutual equilibria can exist at their partition in two-phase systems, when the gross (analytical) concentrations are determined in each phase (by AAS, NAA, or radiometrically) are outlined for: (1) static distribution (batch separation) between two immiscible phases, when both the partial concentrations of A and B and their distribution coefficients generally can be determined by a single or fractional separation, (2) dynamic distribution (chromatographic separation) between the peaks of two metal species, when the potentialities can be strongly affected by secondary equilibria or when the sample-eluent interactions can be assessed.     

Determination of 210Pb in environmental samples

Summary Measurement of ²¹⁰Pb has gained a highly scientific attention due to its wide range of environmental applications. The most commonly used analytical techniques: gamma-spectrometry, beta-counting and alpha-spectrometry were used to measure environmental samples (geological, soil, sediment). Our paper is aiming at comparing the capabilities and limits of application of these three different analytical techniques for ²¹⁰Pb measurement in various environmental samples. In addition, analytical data of ²¹⁰Pb measurements with the three different techniques (gamma-spectrometry, beta-counting and alpha-spectrometry) are discussed to highlight the degree of comparability and the most probable sources of discrepancies and errors. Based on the demanded investigation, one analytical technique will be chosen for routine analysis, while the other techniques, if they are available, could be used for analytical quality assurance measures. It was essential to compare the analytical efficacy of each technique, which differ concerning the detection limit (MDA), sensitivity, analytical effort, the duration of analysis and waiting time before analysis.     

Determination of210Pb and210Po in human tissues of Japanese

To determine the levels of²¹⁰Pb and²¹⁰Po in human tissues of people in Japan, various tissue samples were obtained at autopsy from the cadavers of 22 oncologic cases, mainly in Niigata Prefecture in northern Japan, from 1986 to 1988.Wet ashing, followed by electrochemical deposition and alpha spectrometry were used to separate and determine the²¹⁰Pb and²¹⁰Po present. Among the tissues analyzed, the highest concentrations of²¹⁰Pb and²¹⁰Po were observed in bone (sternum), liver, and kidneys. The total body burden of²¹⁰Pb and²¹⁰Po was found to be approximately 427 pCi and 514 pCi, respectively. This estimated²¹⁰Po value did not differ significantly from values found in populations in the U.S.A. and European countries.     

A modified method for the sequential determination of 210Po and 210Pb in Ca-rich material using liquid scintillation counting

This research describes methods for the sequential determination of ²¹⁰Pb and ²¹⁰Po activity concentrations in Ca-rich ash samples collected from oil shale-fired power plants in Estonia. The procedure involves digestion of Ca-rich ash samples in a microwave digestion system, radiochemical separation of ²¹⁰Pb and ²¹⁰Po and their measurements. All samples, blanks and standards were measured by liquid scintillation counting (Quantulus 1220). The method was tested using IAEA (International Atomic Energy Agency) RGU-1 and IAEA-444 reference materials. Spectral calibration/peak identification which included the optimization of α/β discrimination system (pulse shape analyser), and recovery have been made by ²⁰⁹Po and ²¹⁰Pb standard solutions.

     

Analysis of 210Pb and 210Po in Brazilian foods and diets

Radiochemical procedures for the analysis of ²¹⁰ Pb and ²¹⁰ Po in foods and diets are presented. Because of the low beta energy of ²¹⁰ Pb, its analysis was based on a separation of the daughter radionuclide ²¹⁰ Bi by precipitation of lead sulphate, ²¹⁰ Bi ingrowing and beta counting of this nuclide. ²¹⁰ Po analysis was based on wet dissolution of the sample, deposition onto silver disc and counting by alpha-spectrometry. Levels of these radionuclides in individual items and diets of selected university students were determined in order to evaluate the intakes of ²¹⁰ Pb and ²¹⁰ Po as well as the dose due to ingestion of foods and diets in São Paulo city.     

Presence and forms of210Pb,210Bi and210Po in ground level aerosols

A scheme of fractionation of²¹⁰Pb,²¹⁰Bi,²¹⁰Po forms present in air aerosols based on the combination of methods of radiochemical analysis and radiometric deteemination with leaching by different agents has been developed. The ratio between the²¹⁰Pb,²¹⁰Bi,²¹⁰Po present in the aerosol samples was determined experimentally. Carbonate of²¹⁰Pb, and²¹⁰Po and²¹⁰Bi forms connected with oxides prevai in the aerosol component of atmospheric air.