氮气-苯浮选光度法测定痕量锰

提出了根据 Mn( )氧化 I-生成 I2 ,I2 与 I-反应生成 I-3 配阴离子 ,I-3 配阴离子与孔雀绿阳离子发生离子缔合反应 ,用苯和 N2 将此缔合物浮选 ,以光度法测定此缔合物间接测量锰新方法。表观摩尔吸光系数为(ε=5.0 4× 1 0 5 L· mol-1· cm-1) ,测定 5.0μg/2 0 0 m L的锰 ( n=6 ) RSD为 1 .8%。已用于水中锰的测定。     

维多利亚蓝B双波长叠加吸光光度法测定微量亚硝酸根

在稀盐酸介质中 ,维多利亚蓝B(VBB)的最大吸收峰位于 6 13nm ,当与NO- 2 反应后发生颜色变化 ,最大吸收峰红移 ,以试剂空白为参比 ,可观察到在 6 39nm处出现一新的最大吸收峰 ,同时在 5 6 0nm处发生褪色反应 ,最大褪色波长和最大吸收波长处吸光度均与溶液中NO- 2 的浓度成正比 ,其线性范围在 0～ 2 0 μg/ 2 5mlNO- 2 ,摩尔吸光系数分别为ε56 0 =2 .96× 10 4 L·mol- 1·cm- 1,ε6 39=3.2 3× 10 4 L·mol- 1·cm- 1,用双波长叠加法ε56 0 +6 39=6 .19× 10 4 L·mol- 1·cm- 1,相关系数为 0 .9999。由于显色反应在较强的酸性介质中进行 ,方法具有良好的选择性 ,用于环境水中微量NO- 2 的测定 ,结果满意。     

依文思蓝-氨基糖苷类抗生素的显色反应及其分析应用

在pH 2 .0～ 7.0的条件下 ,依文思蓝 (EB)与硫酸新霉素 (NEO)、硫酸卡那霉素 (KANA)、硫酸庆大霉素(GEN)和硫酸妥布霉素 (TOB)等氨基糖苷类抗生素反应生成蓝色离子缔合物 ,最大显色波长位于 672～ 676nm ;不同体系的线性范围从 0～ 9.0至 0～ 1 2 .0mg L ;摩尔吸光系数 (ε)在 1 .75× 1 0 4 ～ 3 .3 0× 1 0 4 L·mol- 1 ·cm- 1之间 ;最大褪色波长位于 61 6～ 62 0nm的区间。用褪色光度法测定时 ,线性范围从 0～ 6.0mg L至 0～ 1 4.0mg L;摩尔吸光系数 (ε)从 1 .2 2× 1 0 4 至 4.63× 1 0 4 L·mol- 1 ·cm- 1 。当用双波长叠加法时 ,ε值在 (2 .97～ 7.93 )× 1 0 4 L·mol- 1 ·cm- 1 之间。探讨了适宜的反应条件及主要的分析化学性质。该方法用于市售药物及尿液中氨基糖苷类抗生素含量的测定 ,结果满意     

阻抑-褪色光度法测定痕量硅

基于NH3 NH4 Cl缓冲溶液介质中 ,Si 对H2 O2 氧化十六烷基三甲基溴化铵 姜黄素离子缔合物的褪色反应的抑制作用 ,提出了测定痕量硅新的高灵敏的褪色光度法。该方法的表观摩尔吸光系数ε50 0=5 .70× 10 5L·mol-1·cm-1;线性范围为 0 .4～ 3.6 μg/L ;线性回归方程ΔA =2 .2 3× 10 -4 + 0 .0 2 0 17CSi (μg/L) ;相关系数r =0 .9999;测定下限为 2 0× 10 -8g/L。本法用于人发样和水样中痕量硅的测定 ,结果满意。     

溶剂浮选缔合物光度法测定痕量硒

根据亚硒酸 ( H2 Se O3)氧化 I-生成 I2 ,I2 与 I-配阴离子 ,I-3 ,配阴离子I-3 与孔雀绿阳离子 ( MG+ )发生离子缔合反应 ,用 N2 气将此缔合物浮选的三元缔合物用光度法测定硒。方法的 ε为 2 .2× 1 0 6L· mol-1· cm-1,RSD为2 .7% ,检出限为 4.7× 1 0 -10 g· m L-1     

5-Br-PADAP为显色剂吸光光度法测定微量重铬酸根的研究

研究了 2 (5 溴 2 吡啶偶氮 ) 5 二乙氨基酚 (5 Br PADAP)在硫酸介质中质子化后与Cr2 O2 - 7形成二元离子缔合物的最佳条件 ,提出了测定微量Cr2 O2 - 7的吸光光度新方法 ,表观摩尔吸光系数ε580 =1.1× 10 5L·mol- 1·cm- 1。Cr2 O2 - 7浓度范围为 0～ 6 .2 4 μg·ml- 1。缔合物组成比为n(5 Br PADAP)∶n(Cr2 O2 - 7) =1∶1,方法应用于合金钢中铬的测定 ,结果满意     

铑-钨酸盐-罗丹明B缔合显色反应的研究及应用

在聚乙烯醇 (PVA)存在下 ,铑 ( )与钨酸盐及罗丹明 B(RB)形成的离子缔合物在 570 nm处产生最大吸收。建立了测定铑 ( )的光度分析方法 ,其表观摩尔吸光系数 ε达 1 0 7(L·mol-1·cm-1)数量级。方法的检测范围为 0～ 50ng/2 5m L ,检出下限为 0 .2 9ng/2 5m L。大量存在的常见离子对 Rh( )的测定不干扰。用此方法测定了催化剂及工业产品中铑的含量 ,结果与标准方法 (Sn Cl2法 )一致。     

钼(Ⅳ)-4-(2-苯并噻唑偶氮)邻苯二酚多元络合物显色体系及其应用于钼(Ⅵ)的测定

pH4．5时，Mo（Ⅵ）与显色剂4-（2-苯并噻唑偶氮）邻苯二酚反应形成带负电荷的稳定紫红色1∶2二元络合物。40％丙酮水溶液中λmax为560nm，表现ε560为6.33X104L·mol-1·cm-1。它可与二苯胍进一步反应形成电中性的稳定紫红色1∶2∶1三元离子缔合络合物。其氯仿萃取液的λmax为546nm，表现ε5460为7．56X104L·mol-1·cm-1。Mo（Ⅵ）含量在0．02～0．72mg／L范围内均遵从比耳定律。建议了两种络合物的结构。三元体系具有更好的选择性。将拟定的分析方法用于合金钢试样中小量或痕量钼的测定，取得了满意的结果。     

镧-滂胺天蓝光度法测定人血清及尿样中的几种抗生素

在pH 2 .8～ 6 .5的条件下 ,镧 和 6 ,6′ (2 ,2′ -二甲氧基 4 ,4′ -亚联苯基双偶氮 )二 (5 羟基 4 氨基 1 ,3 萘二磺酸钠 ) (滂胺开蒸 ,PSB)与硫酸新霉素 (NEO)、硫酸庆大霉素 (GEN)、硫酸卡那霉素 (KANA)反应生成具有明显显色峰和褪色峰的三元蓝色离子缔合物。其最大显色波长位于 6 88nm ,线性范围从 0～ 1 2 .0mg/L至 0～ 1 4 .0mg/L ,摩尔吸收光系数 (ε)在 3.0 8× 1 0 4～ 4 .6 4× 1 0 4L·mol-1 ·cm-1 之间 ;最大褪色波长在6 1 8～ 6 2 4nm之间 ,线性范围从 0～ 1 2 .0mg/L至 0～ 1 5 .0mg/L ,摩尔吸光系数 (ε)在 4 .4 3× 1 0 4～ 1 .1 3× 1 0 5L·mol-1 ·cm-1 之间。探讨了适宜的反应条件、主要分析化学性质及三元缔合物的络合比。该法用于人血清及尿样中新霉素、卡那霉素及庆大霉素含量的测定 ,结果满意     

曲利本蓝-氨基糖苷类抗生素的显色反应及其分析应用

曲利本蓝 (TB)与硫酸卡那霉素 (KANA)和硫酸妥布霉素 (TOB)等氨基糖苷类抗生素在pH 2 .0～ 7.0的条件下反应生成蓝色离子缔合物。其最大显色波长位于 680nm(TOB)和 686nm(KANA) ,线性范围分别是 0～ 1 1 .0 μg mL(TOB)和0～ 1 3.0 μg mL(KANA) ,摩尔吸光系数 (ε)分别为 5 .32× 1 0 3(TOB)和 3.64× 1 0 3(KANA)L·mol-1·cm-1;最大褪色波长位于 5 88nm(TOB)和 5 90nm(KANA) ,线性范围均为 0～ 1 1 .0 μg mL ,摩尔吸光系数 (ε)分别为 1 .84× 1 0 4 (TOB)和 1 .1 1× 1 0 4(KANA)L·mol-1·cm-1。当用双波长叠加法时 ,ε值分别为 2 .37× 1 0 4 (TOB)和1 47× 1 0 4 (KANA)L·mol-1·cm-1。探讨了适宜的反应条件及主要的分析化学性质。该方法用于市售药物中氨基糖苷类抗生素的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.