Spectrophotometric determination of titanium in plants using 5,5′-thiodisalicylic acid

Titanium (IV) forms a yellow-colored chelate with 5,5′-thiodisalicylic acid, whose sensibility is pD = 6.1 between pH 4 and 6. The stoichiometry of the complex formed is 1:1 at pH 0.5. The system follows Beer's law at pH 4.9 (λ = 385 nm) over the concentration range 0.6–3.2 ppm (ε = 16000 liters · mol⁻¹ · cm⁻¹). The method can be suitably used for determination of titanium in plants.     

A study of the spectrophotometric determination of traces of cadmium(II) and copper(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the presence of polyglycol octylphenyl ether

A spectrophotometric study of the Cd(II) and Cu(II) complex of a new reagent, 2-(5-bromo-2-pyridylazo)-5-diethylamino phenol (5-Br-PADAP) in the presence of polyglycol octylphenyl ether (OP) is presented. A reddish binary complex is formed at pH 9 and shows maximal absorbance at 560 nm with molar absorptivity of 1.16 × 10⁵ · mol⁻¹ · cm⁻¹ liter (Cd), 1.5 × 10⁵ mol⁻¹ · cm⁻¹ · liter (Cu). Beer's law is followed over the range 0.0 to 20 μg cadmium(II) and 0.0–18 μg copper(II). The continuous variation method and molar ratio method showed that the metal ligand ratio is 1:2; ordinarily, most ions do not interfere with the determination and the method can be applied for direct spectrophotometric determination of cadmium(II) and copper(II) in actual samples and the results obtained are satisfactory.     

Spectrophotometric study of vanadium(V)-phenylfluorone complex

Spectrophotometric studies of the reaction between vanadium(V) ions and phenylfluorone are presented and used for spectrophotometric determination of vanadium(V). The absorbance at 520 nm obeys Beer's law in the range of 2–15 μg vanadium/10 ml at pH 4. The relative standard deviation is 2% and the molar absorptivity based on vanadium is 2.1 × 10⁴ liters/mol cm. The composition of the complex in solution is of the 1:1 type with stability constant values to 2.5 × 10⁴. Analysis of the solid complex shows that its formula agrees with the formula (C₁₉ H₁₁ O₅)VO₂ · 5H₂O.     

Isophthaldihydroxamic acid as a spectrophotometric reagent for the determination of molybdate ion

Isophthaldihydroxamic acid produces colored solutions with molybdate ions in basic medium. The resultant product is extracted into a toluenic solution of trioctylmethylammonium chloride (Adogen). The yellow color obtained in the organic solvent (molar absorptivity 6.050 liters · mol⁻¹ · cm⁻¹ at a wavelength of 350 nm) has been used for the spectrophotometric determination of molybdenum in the range of 1.3 to 6 ppm with a relative error of the mean value of 1.3%.     

Extraction-visible spectrophotometric method for determination of nitrate : Application to water analysis

An extraction-visible spectrophotometric method for determination of nitrate is described. The method is based on the extraction of nitrate with tetraphenylphosphonium chloride and the exchange of the nitrate in the colorless Ph₄P-NO₃ extract by intensely colored vanadium(V)-4-(2-pyridylazo)resorcinol complex. The color intensity of this extract is very stable and reproducible. Absorption maximum appears at 560 nm with molar absorptivity 3.6 · 10⁴ 1 mol⁻¹cm⁻¹. The application of the method to water analysis was investigated and the procedure for determination of nitrate in drinking water is developed.     

Spectrophotometric determination of vanadium in steel and alloys with 2-(5-chloro-2-pyridylazo)-5-dimethylaminophenol

Using spectrophotometric methods, the protopysis constant of the 5.ClDMPAP reagent (pK_a1 = −0.19; pK_a2 = 1.97; pK_a3 = 11.98) and the stability constant of its vanadic complex (6.0 ± 0.11) × 10¹⁴ were determined. A high-sensitivity spectrophotometric method was developed to determine V(V) using 0.1–1.2 ppm and pH = 3.8. ε₅₈₆ = 55,300 ± 400 liters · mol⁻¹ · cm⁻¹. A study on the most important interferences and the way to eliminate them was carried out. The method can be applied to the determination of the element in steels and ferrovanadiums.     

Copper(II)-cetyltrimethylammonium chloride-chromal blue G ternary complex and its application to the spectrophotometric determination of copper(II)

A sensitive spectrophotometric method for the determination of copper(II) based on a ternary complex with chromal blue G, a triphenylmethane reagent in the presence of cetyltrimethylammonium chloride, is described. The sensitivity of color reaction between copper and chromal blue G has been greatly increased by the sensitizing action of cetyltrimethylammonium chloride, a cationic surfactant. The color development of the ternary complex can be utilized in the highly sensitive spectrophotometric determination of copper. The molar absorptivity of the binary complex between copper and chromal blue G ε_630nm = 9.56 × 10³liters · mol⁻¹ · cm⁻¹ is enchanced on ternary complex formation to ε_{542 nm} = 4.78 × 10⁴liters · mol⁻¹ · cm⁻¹. The ternary complex gave a maximal absorbance at 542 nm in the pH range 9.8–11. Beer's law is obeyed up to at least 1.2 ppm of copper. The maximal absorbance of the ternary complex was found to develop within 5 min and then it remains constant for several hours. The formation constant of the ternary complex is calculated to be 8.6 × 10¹⁰ under these conditions.     

Extraction and spectrophotometric determination of vanadium with 4-(2-thiazolylazo)resorcinol and tetraphenylarsonium and phosphonium chlorides

Extraction of vanadium-4-(2-thiazolylazo)resorcinol complexes by quaternary salts such as triphenylmethylarsonium iodide, tetraphenylarsonium chloride, and tetraphenylphosphonium chloride has been studied. Quantitative extraction is achieved with tetraphenylarsonium and tetraphenylphosphonium chlorides in the pH region between 3.5 and 5. The optimum conditions for the extraction and spectrophotometric determination of vanadium in the extract are: pH 3.8–4.0, the concentration of vanadium 0.1–0.4 μg/ml. Effective molar absorptivity at λ_max = 555 is (2.55 ± 0.05) × 10⁴ liters mol⁻¹ cm⁻¹. Beer's law is obeyed. Relative standard deviation is 2–10% depending on the concentration level. The composition of the extracted complexes was studied in the solution and in the solid state. For their characterization chemical and spectral evidence and comparison with the vanadium-PAR complexes have been combined.     

Column Preconcentration of Aluminum and Copper(II) in Alloys, Biological Samples, and Environmental Samples with Alizarin Red S and Cetyltrimethylammonium-Perchlorate Adsorbent Supported on Naphthalene Using Spectrometry

A column method has been established for the preconcentration of aluminum and copper(II) with Alizarin Red S and a cetyltrimethylammonium-perchlorate ion pair supported on naphthalene, using a simple glass-tipped tube. Aluminum and copper(II) react with Alizarin Red S to form water-soluble colored chelate anions. These chelate anions form water-insoluble ternary complexes with the adsorbent on the inactive surface of naphthalene packed into a column. They are quantitatively retained in the pH ranges of 4.7-5.2 for aluminum and 5.0-10.0 for copper. The solid mass is dissolved out from the column with 5 ml of dimethylformamide (DMF) for aluminum and 5 ml of ethanol for copper and the absorbance was measured with a spectrometer at 525 nm for aluminum and at 529 nm for copper. The calibration curves were linear over the concentration ranges of 0.25-5.0 μg of aluminum in 5 ml of DMF solution and 0.50-12.0 μg of copper in 5 ml of ethanol solution. The molar absorptivities and Sandell′s sensitivities were respectively calculated to be 2.8 × 10⁴ liter · mol⁻¹ · cm⁻¹ and 9.62 × 10⁻⁴ μg · cm⁻² for aluminum and 2.5 × 10⁴ liter · mol⁻¹ · cm⁻¹ and 2.5 × 10⁻³ μg · cm⁻² for copper. Seven replicate determinations of sample solutions containing 2.5 μg of aluminum and 6.0 μg of copper gave mean absorbances of 0.520 and 0.480 with relative standard deviations of 1.67 and 0.33%, respectively. Interference due to various foreign ions has been studied and the method has been applied to the determination of aluminum in standard alloys, tea leaves, vehicle particulates, copper in coal fly ash, and commercial salt samples.     

Spectrophotometric determination of Si(IV) with 3,6-dichloro-2,5-dihydroxy-1,4-benzoquinone

A new rapid spectrophotometric method for the determination of Si is described. Chloranilic acid (CA) reacts with Si(IV) forming a complex, which is stable for several hours. The procedure is suitable for the determination of Si in the concentration range of 0.5–5.0 μmol/ml, at pH 1.25 ± 0.05 measured at 370 nm. The relative standard deviation at the level of 1.0 μmol/ml Si is ± 3.5%. Of the foreign ions investigated, Fe, Ti, Mo, and PO₄³⁻ interfere significantly.     

Ethylisobutrazine hydrochloride as a selective and sensitive reagent for the spectrophotometric determination of vanadium(V) and its application to vanadium-bearing minerals and alloys

Ethylisobutrazine hydrochloride is proposed as a selective and sensitive reagent for the spectrophotometric determination of vanadium(V). It forms a red-colored species with vanadium(V) in 3.5–6.5 M phosphoric acid medium. An eight-fold molar excess of reagent is necessary for the full development of the color. The red species exhibits an absorption maximum at 518 nm with a molar absorptivity of 9.75 × 10³ liters mol⁻¹ cm⁻¹. Sandell's sensitivity is 5.2 ng cm⁻². Beer's law is obeyed over the range 0.1–6.2 ppm of vanadium(V) with an optimum concentration range of 0.4–6.0 ppm. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions, are reported. The method has been used successfully for the determination of vanadium in ilmenite and vanadium steels that contain chromium, molybdenum, manganese, nickel, copper, tungsten, and titanium.     

Spectrophotometric determination of manganese with 2-oximinocyclohexanone thiosemicarbazone

The 2-oximinocyclohexanone thiosemicarbazone forms, in basic medium, a violet complex with Mn(III) whose stoichiometry is 3:1 (reagent:Mn(III)). The molar absorptivity has a value of 3000 liters · mol⁻¹ · cm⁻¹. By means of the formation of this complex manganese can be determined between 9 and 400 μg with a relative error (95% confidence level) of 0.20%. The effect of foreign ions has been examined and the method has been applied to Mn(II) determination in Lincolnshire iron ore.     

Solid substrate-room temperature phosphorimetry for the determination of trace protein using ion association complex [Cu(BPY)2]·[(Fin)2] as a phosphorescent probe

Fluorescein (HFin) emitted strong and stable room temperature phosphorescence (RTP) on filter paper after set at 50 °C for 10 min using Li⁺ as the ion perturber. HFin existed as Fin⁻ when the pH value was in the range of 5.45–7.36. Fin⁻ could react with [Cu(BPY)₂]²⁺ (BPY: α,α-bipyridyl) to produce ion association complex [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻, which could enhance the RTP signal of Hfin. In the presence of bovine serum albumin (BSA), the –COOH group of Fin⁻ in the [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻ could react with the –NH₂ group of BSA to form the ion association complex [Cu(BPY)₂]²⁺·[(Fin-BSA)₂]²⁻, which contained –CO–NH– bond. This complex could sharply enhance the RTP signal of Hfin and the ΔI_p was directly proportional to the content of BSA. According to the facts above, a new solid substrate-room temperature phosphorimetry (SS-RTP) for the determination of trace protein had been established using the ion association complex [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻as a phosphorescent probe. This method had wide linear range (0.40 × 10⁻⁹–280 × 10⁻⁹ mg l⁻¹), high sensitivity (the detection limit (LD) was 1.4 × 10⁻¹⁰ mg l⁻¹), good precision (RSD: 3.4–4.9%) and high selectivity (the allowed concentration of coexistent ions or coexistent materials was high). It had been applied to the determination of the content of protein in 10 kinds of real samples, and the result agreed well with pyrocatechol violet-Mo (VI) method (P.V.M.M.), which indicated it had high accuracy. Meanwhile, reaction mechanism for the determination of trace protein with [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻ phosphorescent probe was also discussed. The academic thought of this research could not only be used to develop many kinds of ion association complex phosphorescent probes, but also provided a new way to promote the sensitivity of SS-RTP.     

Determination of Trace Amount of Silver by Atomic-Absorption-Spectrometry-Coupled Flow Injection On-Line Coprecipitation Preconcentration Using DDTC–Copper as Coprecipitate Carrier

A flow injection on-line coprecipitation preconcentration system with diethyldithiocarbamate (DDTC) chelate of copper used as the coprecipitate carrier was coupled with flame atomic absorption spectrometry (FAAS) for the determination of trace silver. Silver was on-line coprecipitated with DDTC-Cu(II) in 0.5 moL · L⁻¹HCl, and the precipitate was collected in a knotted reactor. The precipitate was then dissolved by isobutyl methyl ketone and transported directly into the nebulizer–burner system of a flame atomic absorption spectrometer. A detection limit (3ς) of 0.6 μg · L⁻¹was achieved for a loading period of 30 s, a relative standard derivation of 2.0% was obtained for 11 determinations of 20 μg · L⁻¹Ag(I). Interference-free levels were 10 mg · L⁻¹for Cd²⁺, 50 mg · L⁻¹for Cu²⁺, 50 mg · L⁻¹for Mn²⁺, 25 mg · L⁻¹for Ni²⁺, 100 mg · L⁻¹for Pb²⁺, 50 mg · L⁻¹for Zn²⁺, 500 mg · L⁻¹for Fe³⁺, and 2000 mg · L⁻¹for Fe²⁺reduced from Fe³⁺by ascorbic acid. The developed method has been successfully applied to the determination of trace amount of silver in geological samples.     

Extractive-spectrophotometric determination of trace amounts of potassium with cryptand 2.2.2 and methyl orange

A spectrophotometric study on the extraction of potassium into chloroform as an ion pair, formed between the cryptand 2.2.2-potassium complex and the highly colored methyl orange counterion, is described. Optimum conditions for extraction are established (potassium recovery 100.2 ± 3.5%) and a new spectrophotometric determination of trace amounts of potassium is proposed (linear working range: 0.3–3.5 ppm of K⁺; apparent molar absorptivity: 2.2 × 10⁴ liters · mol⁻¹ · cm⁻¹; precision, in terms of relative standard deviation: 1.9%). The actual possibilities of predicting relevant analytical performance characteristics (i.e., sensitivity, selectivity, and precision) of these methods in the light of known complexing ability of cryptands in aqueous phase are discussed. The results obtained in this study are compared with those previously obtained using crown ethers as ligands.     

Development of a new method for the separation of vanadium species and chloride interference removal using modified silica capillaries-DIN-ICP-MS

A new on-line method for the separation of vanadium (IV) and vanadium (V) as well as for the removal of ClO⁺ mass spectral interference on vanadium determination by quadrupole-ICP-MS has been developed. The sample introduction system consists of a modified fused silica capillary coupled to a direct injection nebuliser (DIN), between the solvent delivery system and the ICP. Fused silica capillaries were treated with different anion and cation exchanger reagents and were tested for the retention of Cl⁻ and the separation of vanadium ions at μg l⁻¹ levels. A suitable strong anion exchanger functional group (3-aminopropyltrimethoxy silane) was selected. Chlorine anions were retained in this anionic capillary and the separation between V(IV) and V(V) was possible in the pH range 2–4. The selections of instrumental ICP-MS conditions for the minimisation of the ClO+ interference were carefully considered. Factors affecting the chromatographic separation such as sample pH, sample flow rate, effect of methanol in the mobile phase and length of the capillary for the separation were optimised. The proposed methodology provides a simple and rapid method for vanadium speciation. A relative detection limit of 12 l⁻¹ (i.e. absolute detection limits of 120 pg) for V(IV) based on peak height measurements was obtained. The relative standard deviation for V(IV) was 2.4% for a 10 μl injection (n=6).     

Selective determination of total vanadium in water samples by cloud point extraction of its ternary complex

A highly sensitive micelle-mediated extraction methodology for the preconcentration of trace levels of vanadium as a prior step to its determination by flame atomic absorption spectrometry (FAAS) has been developed. Vanadium was complexed with 1-(2-pyridylazo)-2-naphthol (PAN) and hydrogen peroxide in acidic medium (0.2 mol L⁻¹ phosphoric acid) using Triton X-100 as surfactant and quantitatively extracted into a small volume of the surfactant-rich phase after centrifugation. The color reaction of vanadium ions with hydrogen peroxide and PAN in phosphoric acid medium is highly selective. The chemical variables affecting cloud point extraction (CPE) were evaluated and optimized. The R.S.D. for 5 replicate determinations at the 20 μg L⁻¹ V level was 3.6%. The calibration graph using the preconcentration system for vanadium was linear with a correlation coefficient of 0.99 at levels near the detection limits up to at least 0.6 μg L⁻¹. The method has good sensitivity and selectivity and was applied to the determination of trace amounts of vanadium in water samples with satisfactory result. The proposed method is a rare application of CPE-atomic spectrometry to vanadium assay, and is superior to most other similar methods, because its useful pH range is in the moderately acidic range achieved with phosphoric acid. At this pH, many potential interferents are not chelated with PAN, and iron(III) as the major interferent is bound in a stable phosphate complex.     

Selective Sorption–Spectrometric Determination of Nanogram Amounts of Vanadium(IV) and Vanadium(V)

Conditions of the selective sorption–spectrometric determination of vanadium(IV) and vanadium(V) using sulfonitrophenol M were found. The determination of vanadium (visual test (RSD = 30%) using a reference color scale or quantitative determination (RSD < 10%) by diffuse reflectance spectra is performed immediately after the dynamic-mode sorption of its colored complexes with sulfonitrophenol M at pH 3.5 (vanadium(IV)) or with sulfonitrophenol M and hydroxylamine at pH 1.5 (vanadium(V), 650 nm) at the surface of polyamide membrane disks (d= 1 cm, l= 0.1 mm, m= 2.7 mg). The flow rate is 10–20 mL/min. The detection limit is 5–7 ng of vanadium in the support zone or 0.2–0.5 ng/mL. The determination of 0.5–5 ng/mL vanadium(V) at pH 1.5 does not interfere with 20-fold amounts of V(IV) and 1000-fold amounts of Ni, Zn, Cd, Mg, Co, Cr(III), Mn, PO^3- ₄, and F^–.     

Dynamical Spin Chirality and Magnetoelectric Effect of α-Glycine

Dynamical spin chirality of α-glycine crystal at 301−302 K was investigated by DC (direct current)-magnetic susceptibility measurement at temperatures ranging from 2 to 315 K under the external magnetic fields (H=±1 T) parallel to the b axis. The α-glycine crystallizes in space group P2₁/n with four molecules in a cell, which has centrosymmetric charge distribution. The bifurcated hydrogen bonds N⁺(3)−H(8)···O(1) and N⁺(3)−H(8)···O(2) are stacked along the b axis with different bond intensities and angles, which form anti-parallel double layers. Atomic force spectroscopy result at 303 K indicated that the surface molecular structures of α-glycine formed a regular flexuous framework in the b axis direction. The strong temperature dependence is related to the reorientation of NH³⁺ group and the electron spin flip-flop of (N⁺H) mode. Under the opposite external magnetic field of 1 T and −1 T, the electron spins of N⁺(3)−H(8)···O(1) and N⁺(3)−H(8)···O(2) flip-flop at 301−302 K. These results suggested a mechanism of the magnetoelectric effect based on the dynamical spin chirality of (N⁺H), which induced the electric polarization to produce the onset of pyroelectricity of α-glycine around 304 K.     

Extraction and spectrophotometric determination of trace amounts of niobium with diphenylglioxal-bis-(2-hydroxybenzoylhydrazone)

A method is described for the direct spectrophotometric determination of microamounts of niobium based on its extraction into chloroform with dephenylglyoxal-bis-(2-hydroxy benzoyl) hydrazone (BSHB). This reagent builds up a chelate with Nb(V) in very acidic media, its chloroform solution being pink to reddish depending on niobium concentration (λ_max = 495 nm). Optimum conditions for chelate extraction and niobium determination have been established. The precision of procedure proposed, expressed in terms of relative standard deviation, is ±1.0%.It is shown that the method is sensitive, the molar absorptivity being 1.95 ± 0.02 × 10⁴ liter · mol⁻¹ · cm⁻¹ in the organic phase, and the interferences study demonstrates a high selectivity against common cations and the majority of those accompanying niobium in its natural sources and special alloys.