Al激光等离子体的谱线展宽及线形研究

我们对Al激光等离子体的空间分辨光谱进行了研究。在2300—4000?波段观察到属于AlⅠ,AlⅡ及AlⅢ的近30条发射谱线。这些谱线的线宽及线移量随等离子体离开靶面的距离而变。我们选了五条不同离化态的谱线,根据Griem的理论公式及一部分实验数据,用半经验的方式对靶面附近的电子密度进行了粗略测量。发现不同离化态的Al原子谱线展宽数据之间符合较好,可以用来估算1×10¹⁷—5×10¹⁸cm^-3范围的等离子体电子密度。但有关线移的数据则符合得较差,特别是AlⅡ的3586?及AlⅢ的3610?。这有待进一步的研究。 关键词：     

激光诱导等离子体中Al原子发射光谱的时间、空间演化特性实验研究

实验测定了激光诱导Al等离子体中390.068,394.4,396.152,466.3056 nm等谱线的时间、空间分辨特性,由发射光谱线的强度和Stark展宽计算了 Al等离子体中的电子密度,并由实验结果讨论了电子密度的时间空间演化特性.实验结果表明,当延时在100～1500 ns变化时,等离子体巾的电子密度变化范围为0.02×1017～1.4×1017cm-3,在沿激光束方向上,当距离靶表面0～1.8 mm范围内变化时,相应的电子密度范围为0.28x1017～0.95×1017cm-3,等离子体电子密度在沿激光束方向上具有很好的对称性.     

利用Hβ线的Stark加宽计算激光诱导Cu等离子体的电子密度

潮湿空气中,利用Nd:YAG脉冲激光烧蚀Cu靶获得等离子体发射光谱,依据谱线波长和相对强度等信息计算了等离子体的电子温度;在此基础上,分别用三种方法由Hβ线的Stark加宽计算得到电子密度,并对结果进行了比较分析,证实：对于电子密度在1015~1016cm-3范围内的等离子体,用Hβ谱线测量电子密度是可靠的. 讨论了等离子体电子温度和电子密度在垂直于靶面方向的空间分布,并从产生机制的角度解释了等离子体的传播过程.     

极化X光谱诊断铝激光等离子体的电子密度

为了准确诊断激光等离子体的电子密度,提出了一种基于极化光谱的类氦共振线与互组合线相对强度比诊断电子密度的方法.该法考虑了激光等离子体发射的X射线存在极化的特性,用极化光谱理论对测量的类氦共振线和互组合线光谱相对强度比进行精密校正,再推导等离子体的电子密度.在2×10 J激光装置上进行了实验,使用极化PET（002）晶体谱仪测量了Al类氦离子光谱,利用光谱的极化特性推出Al等离子体的电子密度约为1.5×1020 cm－3.结果表明极化X光谱推导等离子体电子密度方法适合激光高温高密等离子体诊断.     

金激光等离子体的空间分辨X射线发射谱及其应用

在星光II激光装置上,采用PET平面晶体谱仪与宽20μm的狭缝构成一维空间分辨光谱测量系统,对金平面靶激光等离子体进行观测,获得了沿靶面法向一维空间分辨的金M带发射谱。在实验谱中观察到了Au元素类Ni离子的电四极跃迁线3p63d10(1S0) 3p53d104d(3/2,5/2)J=1。利用电四极跃迁线对电子密度的敏感特性,开展了金激光等离子体电子密度诊断的尝试,确定出利用该谱线进行电子密度诊断的有效范围大致在1019～4.5×1021cm-3之间。     

大气压等离子体炬电子密度的光谱诊断

利用空心针-板放电装置产生了大气压等离子体炬,采用光谱法测量了其内部及表面的电子密度. 向空心针中通入氩气,在大气环境中产生了长度为1cm的等离子体炬.实验分别测量了Hα谱线和ArⅠ(696.54nm)谱线,通过反卷积方法分离出其相应的Stark展宽,并由此计算了电子密度.结果发现,采用Hα谱线和ArⅠ(696.54nm)谱线Stark展宽计算得到的等离子体的电子密度分别为1.0×10¹⁵cm^－3和3.78×10^{15关键词： 等离子体炬 电子密度 气体温度 Stark展宽}     

激光诱导等离子体LTE态判定方法研究

针对目前等离子体温度测量中常用的Boltzmann平面法和双线法的测量精度较差的问题,提出结合Boltzmann-Maxwell分布和Saha-Eggert公式来提高等离子温度的测量精度;根据高斯公式的面积与峰值关系建立了发射谱线线宽的简便算法,并通过谱线的Stark展宽计算等离子体的电子密度;建立了以McWhirter准则的等离子局部热平衡(LTE)态判据。以铝为被测样品的实验结果表明,随着激光能量的增加,等离子体温度和电子密度随之呈线性上升趋势;激光能量在127～510 mJ范围内的等离子体电子密度变化范围为1.305 32×1017～1.873 22×1017 cm-3,等离子体温度的变化范围为12 586～12 957 K,根据McWhirter准则本实验中所有等离子体均满足LTE态阈值条件;针对在光谱仪波段内可观测到的处于同一电离态谱线相对较少的铝元素,在不适合用Boltzmann平面法计算温度时,利用Saha-Boltzmann方法对100组铝等离子体光谱进行温度测量的相对标准偏差(RSD)为0.4%,相比于双线法的1.3%,大幅提高了测量精度。该计算方法可用于快速计算等离子体温度、电子密度及判断等离子体LTE态,在自由定标、光谱有效性分析、谱线的温度校正、确定最佳采光位置以及等离子体LTE分布状态等研究中都有较高的应用价值。     

Al激光等离子体电子密度的空间分辨诊断

 采用20 μm的狭缝配平面晶体谱仪构成空间分辨光谱测量系统,对Al激光等离子体的K壳层发射谱进行测量。利用Al的Ly-α线谱的翼部Stark展宽效应推得电子密度空间分布轮廓,建立了翼部Stark展宽法测量高密度等离子体电子密度的诊断技术。     

利用H_β线的Stark加宽计算激光诱导Cu等离子体的电子密度

在潮湿空气中,用Nd:YAG脉冲激光器产生的1.06 μm激光烧蚀金属Cu靶产生等离子体,并观测了其空间分辨的发射光谱.依据光谱线波长、相对强度等参数估算了沿靶面法线不同位置等离子体的电子温度.在此基础上,由H_β线的Stark加宽、分别用三种方法计算得到等离子体的电子密度.讨论了电子温度和电子密度沿靶面法线的空间分布特征.结果分析表明:利用环境气体的谱线测量复杂元素等离子体电子密度的方法是可行的.在距离靶面1.0 mm的空间位置附近电子温度骤然降低、电子密度具有最大值的现象可以从激光诱导等离子体产生机制的角度得到定性解释.     

空气中YAG激光诱导Cu等离子体空间特性的研究

在空气中利用Nd: YAG脉冲激光诱导金属Cu靶,产生激光等离子体羽,并获得等离子体羽的空间谱;研究了空间谱线结构;分析了不同空间位置处电子温度和电子密度的空间演化规律;并对等离子体光谱的特性和产生机制进行了讨论. 结果表明：谱线结构、谱线强度和等离子体的电子温度及电子密度都与空间位置变化密切相关,特征谱强度最大值出现在距靶面0.75-1.0mm的空间位置处,此处CuⅠ谱线相对强度最强,在1.25 mm空间位置处电子温度比周边的电子温度偏低,但此处电子密度反而升高,这种现象可以由级联效应得到解释。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.