Chain segment ordering in uniaxially strained networks: A deuterium NMR investigation

The deuterium NMR (²H-NMR) is used for probing the chain segment orientation in polymer networks under uniaxial stress. The method is based on the observation of an incomplete time averaging of quadrupolar interactions affixed to deuterated segments. The samples are end-linked polydimethylsiloxane networks. The ²H-NMR experiments are performed either on labelled network chains or an labelled probe polymer chains dissolved in the network. The basic results are the following: — The induced uniaxial order is related to a uniaxial dynamics of chain segments around the direction of the applied constraint. — A permanent orientation is observed on free polymer chains dissolved in the deformed networks. — The mean degrees of orientational order induced along short and long chains in bimodal networks are the same. These experimental facts appear as evidences for cooperative orientational couplings between chain segments in the deformed networks.     

On the presence of branching in polyaniline chains

The synthesis of polyaniline via the oxidation of aniline with ammonium bisulfate in water and formic acid was monitored potentiometrically by following the yield and changes in the electric conductivity of the polymer. Three basic stages of the process were determined, including the buildup of oligomeric quinone imines, chain propagation via aniline addition of quinone imine groups, and postpolymerization. The oligomeric intermediate products, substituted quinone imines, were isolated. On the basis of IR and NMR data, the presence of tri-and tetrasubstituted aromatic groups and phenazine structural units in the polyaniline chain was revealed.     

Repartition effect of aromatic polyaniline coatings on the separation of bioactive peptides in capillary electrophoresis

The capillary walls of fused-silica capillary electrophoresis (CE) columns were modified with a thin film of polyaniline (PANI), providing open-tubular columns with a stable coating containing aromatic groups and amine functionalities. Fast and efficient separations were observed for small bioactive peptides under acidic conditions on PANI-coated columns. The mechanism of separation is based on hydrophobic interactions between the analytes and the polymeric matrix. Good reproducibility was observed from run-to-run. Due to the simple derivatization procedure, method flexibility, the uniformity of the coating and its stability, conjugated polymers could find practical application in capillary zone electrophoresis (CZE) separations.     

Phenol assisted deaggregation of polyaniline chains: simple route to high quality polyaniline film

High conducting polyaniline films were readily prepared by in situ chemical oxidative polymerization/deposition of aniline in the presence of a very small amount of organic additive such as phenol. The conductivity of a thin ( approximately 150 nm) polyaniline film synthesized in the presence of 0.01 wt % of phenol ( r-PANI) is an order of magnitude higher (as well as better conducting homogeneity) than that of a film (PANI) obtained from the conventional method without an additive. r-PANI also has better adhesion and electrochemical stability/reversibility, more transparency in the visible-light region, and faster/easier doping/dedoping response compared to PANI. The function of phenol molecule is to avoid the formation of the inter- and/or intrachain hydrogen bonding during the growth of the polyaniline chains. The deaggregation/reducing intrachain hydrogen bonding of polyaniline chains by phenol molecules was revealed with IR, SAXS, and SEM data. All these data supported that phenol does assist the deaggregation of polyaniline chains during the growth of polymer chains or nanorods.     

Confinement effect of chain dynamics in micrometer thick layers of a polymer melt below the critical molecular weight

Polymer melts confined in micrometer thick layers were examined with the aid of field-cycling NMR relaxometry. It is shown that chain dynamics under such moderate confinement conditions are perceptibly different from those observed in the bulk material. This is considered to be a consequence of the corset effect, which predicts a crossover between Rouse and reptationlike dynamics for molecular weights below the critical value at confinement length scales much larger than 10RF, where RF is the Flory radius of the bulk polymer coil [Fatkullin et al., New J. Phys. 6, 46 (2004)]. For the polymer species studied, a perfluoropolyether with a molecular weight of 11 000, the Flory radius is of the order 10 nm, so that the experiment refers to the far end of the predicted crossover region from confined to bulk chain dynamics. Remarkably the confinement effect is shown to reach polymer-wall distances of the order 100 Flory radii.     

Molecular orientation ordering in surface layers of polymer films

The spontaneous ordering of fragments of chain molecules near the surface in polymer films is described in terms of the multichain model that allows for local intra-and interchain orientational interactions of chain segments and for transverse fluctuation of their orientation in the approximation of strong planar-orientation order in the layers. Chain packing in the plane-ordered state is impossible unless the interchain interaction parameter has a value of b = 2K ₂/k _B T > b _c. The value of b _c decreases with a growth in chain rigidity (parameter a = 2K ₁/k _B T). The calculated dependence of the limiting values of the quadrupole orientation order parameter S ₀ on the length of the Kuhn statistical segment A = 2a reasonably well describes the experimental data obtained in a study of polymer-homolog (polysaccharide) films by means of the tilted polarized-beam technique at an interchain interaction parameter of b = 1.75. The monolayer thickness (d ? 10 mn) is films of some polysaccharides was calculated from the fit of the theoretical to the experimental dependences of the orientational order parameter and the birefringence on the number of layers.     

The effect of the polyaniline morphology on the performance of polyaniline supercapacitors

The polyaniline (PANI) prepared by the pulse galvanostatic method (PGM) or the galvanostatic method on a stainless steel substrate from an aqueous solution of 0.5 mol/l H₂SO₄ with 0.2 mol/l aniline has been studied as an electroactive material in supercapacitors. The electrochemical performance of the PANI supercapacitor is characterized by cyclic voltammetry, a galvanostatic charge–discharge test and electrochemical impedance spectroscopy in NaClO₄ and HClO₄ mixed electrolyte. The results show that PANI films with different morphology and hence different capacitance are synthesized by controlling the synthesis methods and conditions. Owing to the double-layer capacitance and pseudocapacitance increase with increasing real surface area of PANI, the capacitive performances of PANI were enhanced with increasing real surface area of PANI. The highest capacitance is obtained for the PANI film with nanofibrous morphology. From charge–discharge studies of a nanofibrous PANI capacitor, a specific capacitance of 609 F/g and a specific energy density of 26.8 Wh/kg have been obtained at a discharge current density of 1.5 mA/cm². The PANI capacitor also shows little degradation of capacitance after 1,000 cycles. The effects of discharge current density and deposited charge of PANI on capacitance are investigated. The results indicate that the nanofibrous PANI prepared by the PGM is promising for supercapacitors.     

Anisotropic diffusion of elongated and aligned polymer chains in a nematic solvent

The translational diffusion constant, D, of a polymer solute in a single-domain, nematic liquid crystal solvent (5CB) is measured in directions parallel and perpendicular to the nematic director using a fluorescence two-beam, cross-correlation technique. The solute under investigation is the stiff, conjugated polymer, MEH-PPV. The ratio D parallel/D perpendicular) of diffusion constants (parallel and perpendicular to the director) is observed to be 1.9 +/- 0.3. This is surprisingly small considering that MEH-PPV is known to be both elongated and highly aligned along the liquid crystal director of 5CB. We therefore argue that the structural order parameter of the solvent governs the anisotropy of the diffusion of the solute.     

An entrant of smaller fullerene: C56 captured by chlorines and aligned in linear chains

A smaller fullerene C56 (#913) is stabilized, isolated, and crystallographically characterized as C56Cl10. The geometric parameters of C56Cl10 imply the otherwise unstable cage of C56 can be stabilized by chlorination through releasing its surface strains and maintaining fragmental aromaticity. An unexpected C Cl...ClC short contact, as well as the linear alignment with pearl-necklace-shaped, is revealed in C56Cl10 crystal.     

Influence of ordering in porous TiO2 layers on electron diffusion

Layers of porous TiO(2) fabricated by electrophoretic deposition at different temperatures with subsequent sintering in air were investigated by transient photocurrent measurements in aqueous electrolyte. The effective diffusion coefficient of excess electrons changed between 1.6 x 10(-5) and 1.4 x 10(-4) cm(2)/s depending strongly on the solution temperature during the TiO(2) layer deposition. Characterization, in terms of average degree of preferred orientation, shows that low deposition temperature results in orientation of the nanocrystals forming the porous film. Consequently, the increase of effective diffusion coefficient is attributed to a higher degree of ordering in the nanoporous TiO(2) layer.     

Thickness-dependent ordering of water layers at the NaCl(100) surface

We have determined the ordering properties of water adsorbed at room temperature on the rock salt (100) surface under four different conditions: ultrahigh vacuum, dry nitrogen atmosphere, 45% and 75% relative humidity. Details of the atomic structure are determined for both sides of the solid-liquid interface. The top most layer of NaCl shows a small relaxation that changes from an expansion to a contraction with increasing humidity. Under all measured conditions water monolayers with different ordering properties are present at the interface. Surprisingly, we find that the amount of ordering in the first layer is increasing with increasing thickness of the water film. At a solid-liquid interface, the ordering appears to be correlated with the solubility.     

Rationalisation of weak ferromagnetism in manganese(III) chains: the relation between structure and ordering phenomena

The synthesis, structure and magnetic properties of the one-dimensional chain compounds [Mn(cyclam)(SO4)]ClO4.H2O (1) and [Mn(cyclam)(HCOO)](CF3SO3)(ClO4) (2) are reported. Cyclam is the cyclic tetradentate ligand 1,4,7,11-tetraazacyclotetradecane. Both chain compounds exhibit antiferromagnetic interactions within the chains. A magnetic ordering phase transition at 5.5 K in (1) is investigated by magnetisation measurements along the three principal crystallographic axes of a single crystal and the results show unambiguously that the ferromagnetic ordering is only taking place along one crystallographic axis. The spin structure of the magnetic ordered phase and the magnitude of the ferromagnetic moment are correlated with the crystal structure and symmetry of the compound.     

NEXAFS measurements of the molecular ordering in the boundary layers of liquid crystalline free standing films

By near edge X-ray absorption fine-structure (NEXAFS) spectroscopy a finite molecular tilt angle in the surface layer of a free standing film in the liquid crystalline smectic A phase of C7 was directly detected. Analysis of the angular dependent intensities of the oxygen K edge NEXAFS spectra leads to an average tilt angle of the molecules in the surface layer of about 34°, which is characteristic for the bulk smectic C* phase of C7.     

Confinement effect of polystyrene on the relaxation behavior of polyisobutylene

The dynamic mechanical loss tangent (tan δ) peak of polyisobutylene (PIB) reveals an asymmetrical broad structure with a maximum on the high‐temperature side and a shoulder on the low‐temperature side. By comparing with the literature results, it is suggested that the shoulder and the maximum originate from local segmental motion and Rouse modes, respectively. Blending polystyrene (PS) with PIB has two effects on the relaxation behavior of PIB. One effect is that the maximum and the shoulder are both suppressed, but the maximum is suppressed to a higher extent. After PS forms the continuous phase, the maximum becomes lower than the shoulder, and even almost disappears when the weight ratio of PIB/PS is under 20/80. The other effect is that, before PS forms the continuous phase, the temperature position of the maximum (T_s) and that of the shoulder (T_α) remains constant, but after PS forms the continuous phase, both of them are reduced with decreasing particle size of the PIB phase, in a way similar to nano‐confinement effect on the depression of glass transition temperature. The depression amplitude of T_s is larger than that of T_α. The aforementioned two effects can be interpreted in terms of the limited expansion of free volume of the PIB phase exerted by the PS phase, which affects the maximum to a higher extent than the shoulder because Rouse modes are more sensitive to the free volume than local segments. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Deposition of polyaniline layers with controlled thickness and morphology by in situ polymerization

Method for deposition of layers of the organic semiconductor polyaniline onto various kinds of supports was developed. The method enables control over the layer thickness and morphology. It is based on formation of a polymeric layer on the support in the course of a heterophase in situ polymerization of aniline. Processes of self-organization of polymer chains on a support and their dependence on the in situ polymerization conditions were studied. Characteristics of polyaniline layers of varied morphology on different kinds of supports were analyzed by electron microscopy, spectroscopy, and conductometry.     

Existence of fluid layers in the corners of a capillary with non-uniform wettability

Based on free energy variation we derive the criterion for displacement during water invasion of oil layers, sandwiched between water in corners and in the centre of a capillary with partly altered wettability. This displacement may arise in combination with a piston-like displacement in which the layers are formed, or, alternatively, these two displacements do not occur and a single piston-like displacement arises removing all oil from the pore cross-section at once. The free energy differentials associated with the three displacements determine exactly which displacement(s) happen during water invasion. Depending on the area and the (advancing) contact angle on the surface of altered wettability, as well as on the half-angles of the pore corners, layers may or may not exist. We compare the criterion for the displacement of oil layers with the existing geometrical criterion. The latter always allows a larger range of contact angles and pressure combination for which layers may exist than the presently derived criterion, hence the geometrical criterion is insufficient and is now superceded.     

Silver particles-modified polysulfonic acid-doped polyaniline layers: electroless deposition of silver in slightly acidic and neutral solutions

Polyaniline layers are produced by electrochemical polymerisation of aniline in the presence of small amounts of poly(2-acryalamido-2-methyl-propane-sulfonic acid) in an inorganic acid solution. Electroactivity and in situ conductance of the obtained polysulfonic acid-doped layers are studied in slightly acidic and neutral solutions. Electroless deposition of silver particles is carried out in silver-EDTA complex ion solutions at pH????.2 and pH????.6 by using the polyaniline layers as reductant. The amount of electroless-deposited silver is studied depending on: polymerisation charge used to synthesize the polymer layer, pH of the plating solution, metal ion concentration and dipping time. SEM shows in all cases a highly non-homogeneous distribution of the metallic phase over the surface, the most protruding fibrillar polymer structures favouring the electroless silver deposition. A linear dependence between amount of the polyaniline material and amount of deposited silver is found for the silver plating solutions with the highest investigated concentration (10?mmol?l^??). At lower concentrations (2.0 and 0.4?mmol?l^??), the same amount of silver becomes deposited on polymer layers with markedly different charges. The electroless deposition of silver in the solutions with lower acidity results in lower amounts of deposited silver at otherwise identical conditions. Effects such as charge transfer within the polymer phase and mass transport in the solution are addressed to explain the observed dependencies of the amount of deposited silver on concentration and pH in the different plating solutions.