Low-pump-threshold continuous-wave singly resonant optical parametric oscillator

We describe a compact all-solid-state continuous-wave singly resonant optical parametric oscillator (SRO) with a minimal pump-power requirement. The SRO is based on periodically poled LiNbO(3) as the nonlinear material and is pumped by a 1-W diode-pumped Nd:YVO(4) minilaser at 1.064 microm . By exploiting the intracavity pumping technique in a 50-mm crystal, we have achieved SRO operation threshold at a diode pump power of only 310 mW.At 1 W of input diode power, the SRO delivers 70 mW of output power in the nonresonant idler at 3.66 microm , at a photon conversion efficiency of 55%. Multiparameter tuning of the SRO yields a signal wavelength range from 1.45 to 1.60 microm and an idler wavelength range from 3.16 to 4.02 microm in the mid infrared. The device is characterized by robust turnkey operation and long-term amplitude-stable performance.     

Singly resonant continuous-wave optical parametric oscillator pumped by a diode laser

We report on what is believed to be the first singly resonant cw optical parametric oscillator (SRO) that is directly pumped by a diode laser. The SRO consists of a 38-mm-long periodically poled LiNbO(3) crystal in a four-mirror signal-resonant ring cavity. Pumped by 2.5 W of 925-nm diode-laser radiation, the SRO generates 480 mW of single-frequency idler radiation at 2.1mum . The wavelengths of the signal and the idler output are tuned in the ranges of 1.55 to 1.70mum and 2.03 to 2.29mum, respectively, by tuning the wavelength of the diode laser from 924.0 to 925.4 nm.     

Microsecond pulsed optical parametric oscillator pumped by a Q-switched fiber laser

We report on what is to our knowledge the first optical parametric oscillator (OPO) pumped by microsecond pulses from a wavelength-tunable solid-state laser. The singly resonant OPO (SRO) is based on a periodically poled LiNbO3 crystal and pumped with 2.1-micros-long pulses from an actively Q-switched Yb fiber laser. At an average fiber laser power of 3.6 W, the SRO generates 1.9-micros-long pulses with a repetition rate of 25 kHz and an average power of 560 mW at 3360 nm. The SRO was tuned from 1518 to 1634 nm (signal) and from 3145 to 3689 nm (idler) via the crystal temperature and poling period. By all-electronic tuning of the fiber laser wavelength over 19 nm, tuning of the mid-infrared idler wavelength over 195 nm was achieved.     

2.5-GHz repetition-rate singly resonant optical parametric oscillator synchronously pumped by a mode-locked diode oscillator amplifier system

We report on an optical parametric oscillator (OPO) that is synchronously pumped directly by a diode laser. This laser is an actively mode-locked master-oscillator power-amplifier system that produces 20-ps pulses at 927 nm with a repetition rate of 2.5 GHz and an average power of 0.9 W. The OPO, which is a singly resonant device based on periodically poled lithium niobate, generates 7.8-ps pulses. The OPO threshold is 300 mW of average pump power, and the maximum average idler output power is 78 mW at a wavelength of 2100 nm. By changing the crystal temperature we can wavelength tune the output in the ranges 1530-1737 nm (signal) and 1986-2348 nm (idler). Rapid wavelength tuning of the OPO over 46 nm (signal) and 74 nm (idler) is achieved through tuning the cavity length over 28 microm by use of a piezoelectric transducer.     

Diode-pumped singly resonant continuous-wave optical parametric oscillator with wide continuous tuning of the near-infrared idler wave

We demonstrate wide, continuous tuning of the single-frequency idler wave of a cw singly resonant optical parametric oscillator (SRO). The SRO consists of a periodically poled LiNbO(3) crystal for quasi-phase matching in a four-mirror signal-resonant ring cavity. The SRO, excited by 2.25 W of 924-nm radiation from an InGaAs diode laser, generates as much as 200 mW of single-frequency 2.1-mum idler radiation. We tune the idler frequency continuously within a range as large as 56 GHz by changing the wavelength of the diode pump laser. The versatility of this continuously tunable single-frequency infrared source is demonstrated by recording of N(2)O rovibrational absorption lines near 2.1 mum.     

High-efficiency mid-infrared ZnGeP2 optical parametric oscillator directly pumped by a lamp-pumped, Q-switched CrTmHo:YAG laser

We report a singly resonant optical parametric oscillator (SRO) based on a ZnGeP(2) crystal directly pumped by a lamp-pumped Q-switched CrTmHo:YAG laser. The IR was tunable from 4.7 to 7.8 microm via crystal angle tuning. A maximum optical to optical efficiency of 56% was obtained from the pump (2.09 microm) to total IR at a pump energy of 6.5 mJ. The corresponding idler energy was 1.45 mJ. The SRO was measured to have a slope efficiency of 64% and a threshold of 1 mJ. The spatial beam quality of the idler, characterized by the M(2) parameter, was 1.38 when the SRO was pumped at 2.5 times threshold. These results show that ZnGeP(2) optical parametric oscillators directly pumped by a CrTmHo:YAG laser can be operated efficiently, while maintaining good IR beam quality.     

1.59 W, single-frequency, continuous-wave optical parametric oscillator based on MgO:sPPLT

A watt-level, single-frequency, continuous-wave (cw) singly resonant optical parametric oscillator (OPO) based on MgO:sPPLT is described. Pumped in the green by a frequency-doubled cw diode-pumped Nd:YVO(4) laser at 532 nm, the OPO can provide up to 1.59 W of single-frequency idler output with a linewidth of ~7 MHz at pump depletions of as much as 67%. Using a compact ring resonator and optimized focusing in a 30 mm crystal, a singly resonant oscillation threshold of 2.84 W has been obtained under single-pass pumping. With a single grating period of 7.97 microm, continuous signal and idler coverage over 852-1417 nm is obtained by temperature tuning between 61 degrees C and 236 degrees C. The influence of thermal lensing on idler output power across the SRO tuning range is also verified.     

Doubly resonant continuous-wave optical parametric oscillator pumped by a single-mode diode laser

The performance characteristics of a doubly (signal and idler) resonant continuous-wave optical parametric oscillator based on periodically poled lithium niobate and pumped by a 100-mW single-mode laser diode at 810 nm are reported. Pump power thresholds as low as 16 mW and wavelength tuning over the range 1.15-1.25 microm at the signal and 2.31-2.66 microm at the idler were achieved through variation of crystal temperature, pump wavelength, and grating period. Up to 5 mW of signal output was obtained with the single-mode diode pump, and signal powers of up to 39 mW were obtained when pumping with a 400-mW injection-locked broad-area diode laser.     

High power,continuous wave,singly resonant OPO based on MgO:PPLN

A continuous wave (CW), extra-cavity singly resonant optical parametric oscillator (SRO) has been demonstrated. The SRO was based on 5% Magnesium-Oxide doped periodically-poled Lithium Nio-bate (MgO:PPLN) pumped by a Yb fiber laser centered at 1064.7 nm. The SRO was able to generate light with idler wavelengths ranging from 2.9 to 4.1 μm. For a pump power of 15 W, the idler output power varied from 7.54 W at 3.03 μm to 1.04 W at 4.05 μm. The oscillation thresholds were 2.0 W at idler wavelength 3.03 μm and 7.0 W at 4.05 μm.     

High-power, continuous-wave, mid-infrared optical parametric oscillator based on MgO:sPPLT

We report a stable, high-power, cw, mid-IR optical parametric oscillator using MgO-doped stoichiometric periodically poled LiTaO? (MgO:sPPLT) pumped by a Yb fiber laser at 1064 nm. The singly resonant oscillator (SRO), based on a 30 mm long crystal, is tunable over 430 nm from 3032 to 3462 nm and can generate as much as 5.5 W of mid-IR output power, with >4 W of over 60% of the tuning range and under reduced thermal effects, enabling room temperature operation. Idler power scaling measurements at ~3.3 μm are compared with an MgO-doped periodically poled LiNbO? cw SRO, confirming that MgO:sPPLT is an attractive material for multiwatt mid-IR generation. The idler output at 3299 nm exhibits a peak-to-peak power stability better than 12.8% over 5 h and frequency stability of ~1 GHz, while operating close to room temperature, and has a linewidth of ~0.2 nm, limited by the resolution of the wavemeter. The corresponding signal linewidth at 1570 nm is ~21 MHz.     

Continuous wave optical parametric oscillator for quartz-enhanced photoacoustic trace gas sensing

A continuous wave optical parametric oscillator, generating up to 300 mW idler output in the 3–4 μm wavelength region, and pumped by a fiber-amplified DBR diode laser is used for trace gas detection by means of quartz-enhanced photoacoustic spectroscopy (QEPAS). Mode-hop-free tuning of the OPO output over 5.2 cm^-1 and continuous spectral coverage exceeding 16.5 cm^-1 were achieved via electronic pump source tuning alone. Online monitoring of the idler wavelength, with feedback to the DBR diode laser, provided an automated closed-loop control allowing arbitrary idler wavelength selection within the pump tuning range and locking of the idler wavelength with a stability of 1.7×10^-3 cm^-1 over at least 30 min. Using this approach, we locked the idler wavelength at an ethane absorption peak and obtained QEPAS data to verify the linear response of the QEPAS signal at different ethane concentrations (100 ppbv-20 ppmv) and different power levels. The detection limit for ethane was determined to be 13 ppbv (20 s averaging), corresponding to a normalized noise equivalent absorption coefficient of 4.4×10^-7 cm^-1  W/Hz^1/2. PACS 42.55.Wd; 42.65.Yj; 42.62.Fi     

Continuous-wave, single-frequency intracavity singly resonant optical parametric oscillator at 1.5-μm wavelength

We present a 1.5μm continuous-wave （CW） single-frequency intracavity singly resonant optical parametric oscillator （SRO） based on periodically poled lithium niobate （PPLN）. The SRO is placed inside the ring cavity of a single-frequency 1.06μm Nd：YVO4 laser pumped by a laser diode. The device delivers a maximum single-frequency output power of 310 mW at a resonant signal wavelength of 1.57 μm. The signal wave could be tuned from 1.57 to 1.59 μm by temperature tuning of PPLN crystal over the range of 130 - 170℃.     

Stable, continuously tunable operation of a diode-pumped doubly resonant optical parametric oscillator

We demonstrate, for what is the first time to our knowledge, long-term stable, continuously tunable operation of a doubly resonant optical parametric oscillator (OPO) pumped by a single-stripe diode laser without the use of an external semiconductor amplifier. The OPO is based on periodically poled lithium niobate and is pumped by a 150-mW distributed Bragg grating diode laser. 18-mW total output power is generated at 1.3- and 2.3-mum wavelengths. A cavity-length servo system allows continuous signal tuning of 17 GHz and idler tuning of 10 GHz, limited only by the range of a piezoelectric cavity mirror mount. OPO tuning is demonstrated from 1.1 to 1.4 mum and from 2.2 to 3.7 mum.     

12 W mid-infrared output,singly resonant,continuous-wave optical parametric oscillator pumped by a Yb<Superscript>3+</Superscript>-doped fiber amplifier

We report a continuous-wave singly resonant optical parametric oscillator (SRO) with more than 12 W of idler power at 3414 nm when it was operated at 30°C. The SRO was directly pumped by a single-frequency, ytterbium-doped fiber laser with 49 W linear polarization pump powers, and based on 50 mm long periodically poled MgO:LiNbO₃ crystal (PPMgLN) in two-mirror linear cavity with 30.5 μm grating period. It’s pump power at threshold was 5.4 W. The slope-efficiency and quantum-limited performance reached 26 and 79.2%, respectively. The beam polarization matched the e → e + e interaction in crystal. The idler waves were temperature tuned in the range of 3654 to 3811 nm and 3248 to 3414 nm based on two 50 mm long PPMgLN with 29.5 and 30.5 μm grating period. To the best of our knowledge, this is the highest continuouswave mid-IR output obtained for a fiber laser pumped optical parametric oscillator (OPO).     

基于光学参量振荡器的可调谐红外激光的强度噪声特性

红外激光光源在微量气体、高分辨率光谱分析和量子光学研究等领域具有重要的应用.本文利用锁定单共振光学参量振荡器内腔标准具的方案获得了无跳模连续调谐的红外激光输出,理论和实验研究了红外激光的强度噪声特性,分析了影响强度噪声的因素.通过控制非线性晶体的温度和标准具调制信号实现了对红外激光强度噪声的抑制.当控制非线性晶体工作温度为60℃,内腔标准具调制信号为8 kHz时,单共振光学参量振荡器输出信号光和闲置光的强度噪声分别降低了11和8 dB.     

Continuous wave,singly resonant MgO:PPLN OPO pumped by a Nd:YVO<Subscript>4</Subscript>/YVO<Subscript>4</Subscript> ring laser

A continuous wave (CW), extra-cavity singly resonant optical parametric oscillator (SRO) has been demonstrated. The SRO is based on 5% magnesium-oxide doped periodically-poled lithium niobate (MgO:PPLN) pumped by a CW Nd:YVO₄/YVO₄ ring laser centered at 1064.4 nm. The nonlinear crystal temperature is kept at 120.0 ± 0.1°C and a domain period of 30 μm is used in this experiment. When the pump power is 11 W, an output power of 2.0 W at the idler wavelength of 3.479 μm has been obtained from the OPO. The optical-optical conversion efficiency is about 18.2%, and the slope efficiency is about 20.8%.     

波长可调谐的瓦级连续橙红光激光器

介绍了基于复合腔结构的全固态波长可调谐的连续橙红色激光的输出特性。该复合腔由一个使用周期极化晶体MgO:PPLN的信号光单谐振光参量振荡器和一个LD侧面泵浦Nd:GdVO₄晶体的1 062.9 nm基频光谐振腔构成。s-偏振1 062.9 nm泵浦光抽运单谐振光参量振荡器产生s-偏振信号光腔内独立振荡。通过复合腔结构的优化设计,使独立振荡的p-偏振1 062.9 nm基频光与s-偏振信号光在2个子腔的重叠区内通过Ⅱ类角度匹配KTP晶体的腔内和频过程获得橙红色激光。当MgO:PPLN晶体的调谐温度从30 ℃上升至200 ℃时,s-偏振信号光的中心波长产生红移,导致其与p-偏振1 062.9 nm基频光和频产生的橙红色激光的中心波长从620.2 nm红移至628.9 nm。同时测得中红外波段闲频光的中心波长从3 714.2 nm蓝移至3 438.3 nm。在30 ℃最低设定温度时, 中心波长620.2 nm的橙红色激光和中心波长3 714.2 nm的闲频光最大连续输出功率分别达到2.0 W和2.9 W。     

Optimally-output-coupled, 17.5 W,fiber-laser-pumped continuous-wave optical parametric oscillator

We present a stable, high-power, fiber-laser-pumped, continuous-wave (cw), singly resonant optical parametric oscillator (SRO) for the mid-infrared in an output-coupled (OC) configuration, providing 17.5 W of total output power at 61% extraction efficiency. Using a single-frequency, cw Yb fiber laser at 1064 nm and a 50-mm-long MgO:PPLN crystal, through optimization of signal output coupling we generate up to 9.8 W of signal power in the near-infrared together with 7.7 W of idler power for 28.6 W of pump, while in the absence of output coupling, 8.6 W of idler power is generated for the same pump power at 30% efficiency. The SRO is tunable over 360 nm in the idler range. The deployment of signal output coupling results in a total tuning of 513 nm (120 nm of signal, 393 nm of idler) over which watt-level output power can be extracted. Through careful control of thermal effects we achieve a long-term peak-to-peak idler power stability of 5% over 14 hours near room temperature. The output beams have TEM₀₀ spatial profile with M ²<1.28 for the idler and M ²<1.37 for the signal.     

Wide single-mode tuning of a 3.0- 3.8-mum, 700-mW, continuous-wave Nd:YAG-pumped optical parametric oscillator based on periodically poled lithium niobate

A new optical parametric oscillator (OPO) for the mid-infrared wavelength region of 3-3.8mum with an idler output power of up to 1.5 W has been developed. The singly resonant OPO is pumped by a single-mode, 10-W, continuous-wave Nd:YAG laser and consists of a bow-tie ring cavity with a fan-out periodically poled lithium niobate crystal and a low-finesse intracavity air-spaced etalon. The single-frequency idler output can be continuously tuned over 24 GHz with 700-mW power by tuning of the pump laser. The tuning was demonstrated by recording of an absorption line of ethane with photoacoustic spectroscopy.     

Broadly tunable infrared femtosecond optical parametric oscillator based on periodically poled RbTiOAsO(4)

We present results from what we believe is the first reported example of an optical parametric oscillator based on periodically poled RbTiOAsO(4). The oscillator is pumped by a femtosecond self-mode-locked Ti:sapphire laser and, with a single-grating 2-mm-long crystal and one mirror set, a combination of pump and cavity-length tuning provided wavelength coverage from 1060 to 1225nm (signal) and 2.67 to 4.5 microm (idler). Average output powers were as much as 120mW in the signal and 105mW in the idler and interferometric autocorrelations recorded at signal and idler wavelengths of 1.1 and 3.26 microm, respectively, imply pulse durations of 125 and 115fs, respectively.