城市老旧居住小区交通环境评价指标与评价方法

定量的评判城市老旧居住小区整体交通环境质量并进而科学有效的提出老旧小区交通环境更新与改善措施,对城市老旧居住小区交通环境进行了调查,明确了老旧居住小区存在的突出交通问题,并提出了城市老旧居住小区交通环境评价的指标体系,包括行人跨路出行指数、无人行道路段长度占比、停车泊位供需比、路内非法停车占比、平均停车步行距离、泊位数量户数比、人均步行空间、无障碍通道、盲道设置比例、非机动车泊位供需比、地面停放车辆数小区面积比、外部穿行交通周转量小区面积比等。并给出了具体指标的计算方法与获得办法。以长沙市四个典型老旧居住小区为例,对评价方法进行了论证,并得到城市老旧居住小区存在的一般问题,包括人车混杂、人车交织现象严重,停车泊位短缺、车辆乱停乱放,交通设施、特别是弱势群体交通设施缺乏。给出的评价指标、评价方法与结论可为城市老旧小区改造更新,特别是其中很重要的交通环境更新提供决策依据。     

乡村绿色生态旅游适宜等级VIKOR评估方法

针对乡村绿色生态旅游特征,并考虑旅游者个体感受与群体效益,本文从乡村绿色生态旅游开发与适宜评级概念出发,提出乡村绿色生态旅游适宜等级VIKOR评估模型与方法。首先,从等级评估的概念与内涵出发,刻画乡村绿色生态旅游适宜评级问题,避免混淆旅游适宜评级和排序两个本质不同的问题。然后,构建乡村绿色生态旅游适宜等级评估指标及隶属函数,提出评估指标的熵权确定方法。其次,提出乡村绿色生态旅游适宜等级VIKOR评估模型与二元语义等级评估方法。最后,通过案例研究和比较分析,说明本文所提模型与方法的合理性、可行性与实用性。     

Interpreting linear systems of equalities and inequalities. Application to the water supply problem

This paper shows how the mathematical and the engineering points of view are complementary and help to model real problems that can be stated as systems of linear equations and inequalities. The paper is devoted to point out these relations and making them explicit for the readers to realize about the new possibilities that arise when contemplating the compatibility conditions or the set of general solutions from the dual perspective. After reviewing an orthogonally based powerful algorithm to analyse the compatibility of linear systems of equations and solving them, a water supply problem is used to illustrate its mathematical and engineering multiple aspects, including the optimal statement of the problem in terms of an adequate selection and numbering of equations and unknowns, an analysis of the compatibility conditions and a physical interpretation of the general solution, together with that of each individual generators of the affine space. The possibilities of removing unknowns without altering the compatibility of the problem is also analysed. Next, the Γ‐algorithm to analyse the compatibility of linear systems of inequalities and solving them is described and then, the water supply problem is revisited adding some constraints, such as capacity limits for the pipes and retention valves, and discussed as to how they affect the resulting general solution and other aspects. Finally, some conclusions are derived. Copyright © 2005 John Wiley & Sons, Ltd.     

复杂装备研制协调超网络均衡与实现路径

复杂装备研制主体间呈现社会关系、合作关系、协调关系等网络关系,并且相互影响相互作用,其影响复杂装备研制的重要参数。为有效描述在资源环境约束下制造商和供应商的关系,探讨复杂装备研制协调机理与实现路径,本文利用超网络方法,设计了相互影响、相互作用的社会关系网络、协调网络和合作网络的复杂装备研制协调超网络,并将社会关系水平、协调度和合作水平作为超网络的3个决策变量,建立基于关系价值最大、协调成本最低、协调风险最小、合作收益最大、合作风险最小和成本最小等不同偏好下的多目标最优决策模型,构建了复杂装备研制超网络均衡模型,并利用其探讨超网络均衡和实现路径。     

利益相关者视角下公路货运超限超载的对策研究——基于演化博弈模型和仿真分析

为有效遏制公路货运超限超载现象,深化交通执法领域的“放管服”改革,本研究针对运输者、稽查人员和交管部门等利益相关者,建立三方演化博弈模型,研究超限超载运输中各利益主体的决策演化过程,并对稳定策略的演化路径进行仿真分析,比较不同参数组合下不同政策力度的治理效果。研究发现,提高超限超载运输的处罚系数可以明显规范运输者的行为;管理成本越低,监管部门的策略越可能向积极监管的方向演化;三方博弈系统存在两种可能的演化稳定策略,加重对稽查人员消极执法行为的处罚、加大资金设备投入能够提高系统向最优状态演化的概率。     

On the use of history of mathematics: an introduction to Galileo's study of free fall motion

In this paper, we report on an experimental activity for discussing the concepts of speed, instantaneous speed and acceleration, generally introduced in first year university courses of calculus or physics. Rather than developing the ideas of calculus and using them to explain these basic concepts for the study of motion, we led 82 first year university students through Galileo's experiments designed to investigate the motion of falling bodies, and his geometrical explanation of his results, via simple dynamic geometric applets designed with GeoGebra. Our goal was to enhance the students’ development of mathematical thinking. Through a scholarship of teaching and learning study design, we captured data from students before, during and after the activity. Findings suggest that the historical development presented to the students helped to show the growth and evolution of the ideas and made visible authentic ways of thinking mathematically. Importantly, the activity prompted students to question and rethink what they knew about speed and acceleration, and also to appreciate the novel concepts of instantaneous speed and acceleration at which Galileo arrived.     

激光辐照下圆薄板的动态屈曲研究

对强激光辐照下薄板（铜片）的动态热失稳过程进行了分析，得出了简支圆薄板在热冲击下发生的屈曲及后屈曲过程，并给出了临界激光功率密度与薄板厚径比的关系曲线，方法计入了温度分布、惯性项和缺陷大小对于失稳过程的影响。这一工作有利于人们对强激光引起的硬目标破坏机理的认识。     

基于系统动力学的政府和废旧电子产品处理商演化博弈分析

文章为探究政府管制在废旧电子产品处理商实施生态拆解的作用,运用系统动力学方法构建了废旧电子产品处理问题中政府和处理商之间的一个混合策略演化博弈模型,并对政府管制策略选择与处理商实施生态拆解策略选择的互动机制进行了分析。演化博弈和系统仿真结果表明:处理商实施生态拆解和非生态拆解的收益、政府管制的有效性以及处理商实施非生态拆解受到惩罚等都直接影响系统的演化结果;政府和处理商两群体在3种情形下存在演化稳定策略;在一定的条件下,系统演化呈现周期性特征。最后从政府管制的角度出发,动态策略的演化博弈模型存在演化稳定的均衡点。     

Boundary-Value Problems of the Theory of Thin and Nonthin Orthotropic Shells with Account of Nonlinearly Elastic Properties and Low Shear Rigidity of Composite Materials

The basic geometric and physical relations and resolving equations of the theory of thin and nonthin orthotropic composite shells with account of nonlinear properties and low shear rigidity of their materials are presented. They are derived based on two theories, namely the theory of anisotropic shells employing the Timoshenko or Kirchhoff-Love hypothesis and the nonlinear theory of elasticity and plasticity of anisotropic media in combination with the Lagrange variational principle. The procedure and algorithm for the numerical solution of nonlinear (linear) problems are based on the method of successive approximations, the difference-variational method, and the Lagrange multiplier method. Calculations of the stress-strain state for a spherical shell with a circular opening loaded with internal pressure are presented. The effect of transverse shear strains and physical nonlinearity of the material on the distribution of maximum deflections and circumferential stresses in the shell, obtained according to two variants of the shell theories, is studied. A comparison of the results of the problem solution in linear and nonlinear statements with and without account of the shell shear strains is given. The numerical data obtained for thin and nonthin (medium thick) composite shells are analyzed.     

夜盘交易对我国贵金属期货市场的影响研究

对比了我国贵金属期货市场推出夜盘交易制度前后流动性、波动性与联动性的变化,并研究了该交易制度带来的长期与短期不同的影响。首先,采用经过修正的流动性比率衡量市场流动性,并引入虚拟变量纳入回归模型,进一步研究夜盘交易对市场流动性的贡献;接下来,将每日收益率分解为隔夜收益率和日内收益率,通过建立EGARCH模型,分别考察夜盘交易对隔夜波动率和日内波动率长期与短期的影响;最后,通过建立VAR-BEKK-GARCH模型,从均值和方差两个层面研究了国内外贵金属期货市场间的联动性。研究发现:我国推出的夜盘交易制度显著提高了贵金属期货市场的流动性,降低了贵金属期货市场的波动性,尤其是降低了隔夜收益率的波动性,日内收益率的波动性并没有显著减弱;夜盘交易的推出同时增强了国内外期货市场之间的联动性,提升了我国贵金属期货市场对信息的吸收与传递效率。     

Effect of viscosity of a thermoplastic prepreg and matrix upon winding of rings

The problem of compression of a unidirectional layer and shear of a polymer interlayer during winding of rings is considered. The equations determining the dependence of the layer thickness and stresses on the parameters entering into the power flow law for a prepreg and polymer matrix and on the basic parameters of the winding process—the initial tension of the prepreg, its placement rate, and the radius of a mandrel—are derived. The ring thickness measurements obtained at various temperatures and initial tension forces of plies confirm the adequacy of the model offered. It is found that the viscous properties of the prepreg and matrix upon winding affect the relative change in the layer thickness to a greater extent than the stresses in these layers. With increase in temperature and tension force upon winding, the effect of viscous deformations of the prepreg and matrix increases. A decrease in viscosity and an increase in the tension force of the tape lead to a higher strength of the ring in tension and interlaminar shear; however, the growing percolation of the polymer melt leads to a greater inhomogeneity of the structure of the composite in the ring and to a lower reinforcing effect of the factors mentioned. Presented at the 11th International Conference on Mechanics of Composite Materials (Riga, June 11–15, 2000). Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 3, pp. 419–428, 2000.     

Creep of polymer concrete in the nonlinear region

Two polyester-based polymer concretes with various volume content of diabase as an extender and aggregate are tested in creep under compression at different stress levels. The phenomenological and structural approaches are both used to analyze the experimental data. Common features of changes in the instantaneous and creep compliances are clarified, and a phenomenological creep model which accounts for the changes in the instantaneous compliance and in the retardation spectrum depending on the stress level is developed. It is shown that the model can be used to describe the experimental results of stress relaxation and creep under repeated loading. Modeling of the composite structure and subsequent solution of the optimization problem confirm the possibility of the existence of an interphase layer more compliant than the binder. A direct correlation between the interphase volume content and the instantaneous compliance of the composite is revealed. It is found that the distinction in nonlinearity of the viscoelastic behavior of the two polymer concretes under investigation can be due to the difference in their porosity. Submitted to the 11th International Conference on Mechanics of Composite Materials (Riga, June 11–15, 2000.) Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 2, pp. 147–164, 2000.     

函数空间多体挠性结构系统动力学、稳定性与控制的研究

利用现代数学方法,在函数空间中研究了一类无穷维系统动力学、稳定性与控制问题.首先提出并建立了具有阻尼、陀螺部件和约束阻尼的多拓扑结构多挠体分布参数系统动力学控制模型;其次给出并论证了多体挠性结构特征、系统分析结果--可控可观性充要条件、稳定性理论和系统的渐近性质.研究的结果扩充和发展了本领域关于多挠体系统动力学与控制的理论成果,具有重要的工程意义.     

Influence of Multiple Micro Cracks on the Damage Behavior of a Macro-Crack Tip北大核心CSCD

The solution of an infinite plane containing a macro crack and a cluster of micro cracks under uniaxial tensile load was presented based on Muskhelishvili’s complex function method and the stepwise recursive method. The stress field and stress intensity factor K were obtained. Combined with the damage mechanics, damage parameter D of the macro-crack tip and the micro-crack tip under uniaxial tension was redefined, and the influence of different damage zone forms on the damage of the crack tip was analyzed. The results show that, both the chain-distribution and the reverse-chain-distribution micro cracks have an amplifying effect on the macro crack growth, and the damage parameter increases with the decrease of the inclination angle of the micro crack and the reduction of the distance between the macro crack and the micro cracks. For a relatively small inclination angle of the micro crack, the damage parameters of the macro crack and the micro crack heightens, and the damage parameter of the macro crack increases with the micro-crack length. For evenly distributed micro cracks in the continuous damage zone, the micro cracks have an amplifying effect on the macro-crack growth, and the damage parameter of the macro crack increases with the micro-crack number. © 2022 Editorial Office of Applied Mathematics and Mechanics. All rights reserved.     

Optimal enlistment age: A cost–benefit analysis and some simulations

Enlistment at the earliest viable age maximizes the country’s wartime army size and thereby the country’s attack-deterrence capacity. Injuries and death generate a loss of quantity and quality of life that reduces the benefit from early-age enlistment. The benefit from any age of recruitment is also affected by the rise and decline of the individual’s military performance and civilian productivity and by the changes in the individual’s adjustment costs over his lifecycle. The simulations of an optimization model incorporating these cost and benefit elements suggest that if the intensity of the rise and decline of the individual’s military performance is sufficiently larger than the intensity of the rise and decline of his civilian productivity, there exists an interior optimal enlistment age that is greater than the commonly practiced 18. In such a case, most of the simulation results are closely scattered around 21 despite large parameter changes.     

持股策略下随机需求低碳供应链融资决策均衡

随机市场需求且受制造商减排水平影响,考虑碳限额与交易机制,研究制造商进行单纯银行借贷和供应商投资持股的组合融资时的最优决策和利润情况,分析消费者低碳偏好、碳交易价格和供应商的投资持股比例对供应链的最优决策变量和利润的影响。研究发现:无资金约束、单纯银行借贷和组合融资下,消费者低碳偏好、碳交易价格和持股比例与制造商的减排水平和利润以及供应链系统的利润正相关,而供应商的批发价格和制造商的生产量与消费者低碳偏好正相关,与碳交易价格负相关,而持股比例与供应商的批发价格负相关,与制造商的生产量和减排水平正相关;持股策略下制造商的减排水平和生产量最大,无资金约束时次之,单纯银行借贷时最小;而无资金约束时供应商的批发价格最高,单纯银行借贷时次之,持股策略时最低;在持股比例满足一定条件下,供应商和制造商的利润优于单纯银行借贷时的利润,并且可以优于无资金约束时的利润,提高了供应链的竞争力和效率。     

The generalized hierarchical product of graphs

A generalization of both the hierarchical product and the Cartesian product of graphs is introduced and some of its properties are studied. We call it the generalized hierarchical product. In fact, the obtained graphs turn out to be subgraphs of the Cartesian product of the corresponding factors. Thus, some well-known properties of this product, such as a good connectivity, reduced mean distance, radius and diameter, simple routing algorithms and some optimal communication protocols, are inherited by the generalized hierarchical product. Besides some of these properties, in this paper we study the spectrum, the existence of Hamiltonian cycles, the chromatic number and index, and the connectivity of the generalized hierarchical product.     

Organizational implications of systems thinking: Multidimensional modular design

Despite a well recognized systemic principle that parts of an organization are interdependent and the nature of their interaction defines the behavior of the whole, we have stubbornly held to the illusion that each function is more or less self-contained and can be treated independently. For a majority of managers the unidimensional mode of organization based on structurally defined tasks, segmentation and hierarchical coordination of functions seems to be the only acceptable way of organizing the work. A predominant management culture continues to value narrow specialization very dearly and considers any forms of redundancy in the organizational structure as wasteful and inefficient. However, the ability to adapt requires some forms of flexibility and responsiveness, which in turn demands that some degree of redundancy be built into the system.The required level of interaction and flexibility in an organization can be achieved by creating a modular structure embedded in a multidimensional scheme. The resulting mode of organization is capable of redesigning its structure and redefining its functions, so that it can exhibit different behaviors and produce different outcomes in the same or different environments.     

Dynamics of coupled systems

A survey in the form of a review of the author’s research results in the area of dynamics of coupled rotations and coupled systems is presented. The theorem on the existence of a trigger of the coupled singularities and the separatrix in the form of the number eight is presented with a few examples of coupled rotations of the simple systems with debalances. Also, a survey of models and dynamics of coupled systems composed of a number of deformable bodies (plates, beams or belts) with different properties of materials and discrete layer properties is presented and mathematically described. The constitutive stress–strain relations for materials of the coupled sandwich structure elements are presented for different properties: elastic, viscoelastic and creeping. The characteristic modes of the coupled system vibrations are obtained and analyzed for different kinds of materials and structure composition. The visualization of the characteristic numbers and modes and eigenamplitude forms are presented. Structural analysis of sandwich structure vibrations is done.     

不确定需求下页岩气开发项目投资时机与钻井数量选择研究

基于工程化实现视角,结合规划产能与实际产出的不一致性和产量递减性,构建市场需求不确定情境下页岩气开发项目的投资时机与钻井数量决策模型,给出最佳投资时机和最优钻井数量的解析解,并探讨了不确定性、产量递减率、钻井成功率以及钻井成本变动对最佳投资时机和最优钻井数量的影响。结果表明最佳投资时机受单位有效钻井成本影响却与最优钻井数量多少无关,最优钻井数量受市场需求的期望增长率和波动影响而与市场需求量大小无关;不确定性、产量递减率或钻井成本的增大,将引起投资延迟和钻井数量增加,而钻井成功率的增大则会起到相反的作用;并发现投资阈值与最优钻井数量呈同向变动规律。