铜,钾助剂对铁基催化剂吸附—脱附性能的影响

气-固相催化反应活性很大程度上依赖于反应组分在催化剂表面上的吸附与脱附行为,因此,研究反应组分在催化剂表面的吸附与脱附性质对了解催化剂表面活性部位分布、催化活性、反应机理等具有重要意义。本文用程序升温脱附(TPD)及稳态化学吸附研究了具有良好催化活性的F-T合成铁基催化剂对CO和H_2的吸附、脱附特性,并讨论了Cu、K助剂的影响。     

还原温度对Fe-Mo催化剂性质及F-T合成性能的影响

研究了还原温度对Fe-Mo催化剂性质及费托(F-T)合成性能的影响。采用N₂物理吸附、X射线衍射、穆斯堡尔谱和H₂程序升温脱附技术对催化剂进行了表征。结果表明,随还原温度升高,金属铁晶粒粒径增大,金属铁上的H₂吸附量先升后降;催化剂还原度提高,反应态催化剂碳化铁含量递增。催化剂F-T合成性能在280 ℃、1.5 MPa、2 000 h^-1、合成气H₂/CO比为2.0条件下在固定床反应器中测试。反应结果表明,随还原温度提高,催化剂接近稳态时的活性和重质烃选择性(C₅⁺)先升后降,而甲烷选择性则先降后升。350 ℃还原催化剂具有最佳F-T合成反应性能。     

Mn和Zr助剂对介孔碳负载钴基催化剂费托合成反应性能的影响

采用浸渍法制备了Mn和Zr改性的介孔碳负载钴基催化剂,采用X射线衍射（XRD）、比表面积测定、H₂程序升温还原（H₂-TPR）、H₂/CO程序升温脱附（TPD）及X射线光电子能谱（XPS）等手段对催化剂的物化性质进行了表征,采用固定床反应器对其F-T反应性能进行了研究。结果表明,Mn或Zr助剂的添加均降低了CH₄的选择性。其中,Mn助剂的添加提高了C_2-4的选择性,提高了烯烷比,而Zr的添加提高了钴物种的分散度,增加了反应活性位点,显著提高了钴基催化剂的F-T反应活性和C₅₊选择性。     

钴基费-托合成催化剂上CO、H2的吸附行为

采用程序升温脱附及FT IR技术考察了CO、H2在钴基催化剂上的吸附行为.H2 TPD表明,Co/SiO2催化剂有两类脱附氢,引入锆助剂后,低温脱附氢量明显增加,高温吸附氢量下降.CO TPD及吸附态CO的红外光谱表明锆助剂使CO在钴催化剂上的吸附强度减弱,但其吸附量增大.钴基催化剂的费 托合成反应性能可以用吸附态物种的变化来解释.     

CuO-WO3-ZrO2的结构和性质对苯甲醛加氢反应催化性能的影响

采用共沉淀法制备了不同CuO和WO₃含量的CuO-WO₃-ZrO₂催化剂. 利用X射线衍射(XRD)、 扫描电子显微镜(SEM)、 X射线荧光光谱(XRF)、 N₂气物理吸附、 氢气程序升温还原(H₂-TPR)、 X射线光电子能谱(XPS)及程序升温脱附(TPD)等手段对催化剂的结构和表面性质进行了表征. 结果表明, WO₃的引入可以调变ZrO₂的晶型, 从而使催化剂的比表面积和孔径发生变化, 促进CuO在催化剂表面的分散, 并影响催化剂的酸碱性. 在苯甲醛加氢制备苯甲醇反应中, 以CuO质量分数为18%, WO₃质量分数为10%的CuO-WO₃-ZrO₂为催化剂时苯甲醛单程转化率达到92.03%, 产物苯甲醇的选择性为94.76%.     

Ru添加对Co/SiO2费托合成催化剂性能的影响

用初湿含浸法制备了不同Ru添加量的Co/SiO₂模型催化剂,然后进行N₂物理吸附、XRD、H₂-TPD、DRIFTS等表征和微分固定床费托(F-T)反应评价。F-T反应结果表明,催化剂中添加Ru后,CO转化率显著提高,TOF值增大,CO₂和CH₄选择性降低,烯/烷比(O/P)降低。FT-IR表征说明,催化剂添加Ru后Co-O键的强度减弱,相对应的H₂-TPR也表明,催化剂的还原度得到显著提高。还原后的催化剂XRD结果进一步证实,加入Ru后,催化剂无钴氧化物被检出,并且当Ru添加量为0.5%(质量分数)时催化剂中金属钴主要以六方密堆(hcp)形式存在。CO-DRIFTS结果显示,Ru的加入使CO的吸收峰发生红移,即Ru促进了CO的解离。H₂-TPD结果则表明,随着Ru添加量的增加,催化剂表面CO_ads/Co_s和CO^*/Co_s增大,这是CH₄选择性降低的主要原因。     

In-Co二元金属氧化物上CO2催化加氢反应的选择性转变:催化反应的机理和构效关系

采用催化加氢的方式将CO₂转化为甲醇,既可以减少CO₂排放,又制备了化学品,该反应具有重要的研究意义.氧化铟(In₂O₃)作为CO2加氢制甲醇催化剂,由于其较高的CO₂活化能力和甲醇选择性,被科研工作者广泛研究.其中,将具有良好解离H2能力的过渡金属元素引入In₂O₃(M/In₂O₃)是有效提高催化剂性能的策略之一,然而,M/In₂O₃体系催化CO₂加氢反应机理及活性位点仍不清楚.本文引入Co制备了In-Co二元金属氧化物催化剂应用于CO2加氢制甲醇,结果表明,相较于In₂O₃,In-Co催化剂性能有很大提升,其中In1-Co₄催化剂上甲醇时空产率(9.7 mmol·g_cat^-1 h^-1)是In₂O₃(2.2 mmol·g_cat^-1 h^-1)的近5倍(反应条件:P=4.0 MPa,T=300℃,GHSV=24000 cm³ _STP g_cat^-1 h^-1,H2/CO₂=3).值得注意的是,尽管Co是金属元素的主体,In-Co催化剂中Co催化CO₂甲烷化的活性受到明显抑制.本文还通过多种技术系统研究了催化剂结构与反应选择性转变间的关系.采用电感耦合等离子体发射光谱、粉末X射线衍射、拉曼光谱、X射线光电子能谱和透射电子显微镜等对催化剂结构以及表面性质进行了表征.结果表明,在H₂还原气氛诱导下,In-Co催化剂表面发生重构,形成以CoO为核,以In₂O₃为壳的核壳结构,其在高压反应后仍能保持稳定;更重要的是,该核壳结构可以显著增强In-Co催化剂吸附及活化CO₂的能力.CO₂加氢反应动力学研究表明,Co催化剂上H₂分压对CO₂加氢为零级反应,而H₂分压在In-Co上的反应级数为正数;In-Co催化剂上,CO₂分压的反应级数接近于零,表明CO₂及其衍生物在In-Co的表面吸附饱和,但在纯Co上,则不会发生这种饱和吸附.通过原位DRIFTS研究了催化反应路径和关键中间物种的吸附及反应行为,发现CO₂加氢在纯Co和In-Co上的催化机理均遵循甲酸盐路径.在该催化路径中,CO₂首先加氢为甲酸盐(*HCOO)物种,随后加氢为甲氧基(*CH₃O).*CH₃O在Co催化剂上进一步加氢生成CH₄,而*CH₃O在In-Co催化剂上则会脱附生成CH₃OH.根据表征结果,本文认为,在还原性气氛下,In-Co发生了重构并生成表面富In₂O₃的核壳状结构,显著提高了催化剂对CO₂和含碳物种的吸附能力.Co和In-Co催化剂对CO₂加氢反应选择性的差异归因于催化剂对CO₂和对*HCOO等含碳中间物种的吸附稳定性不同.CO₂及其衍生的含碳中间物种在In-Co催化剂上的吸附能力比在Co催化剂上强,形成了较合适的催化剂表面C/H比,从而使*CH₃O能够脱附为CH₃OH,而不是进一步加氢为CH₄.综上,本文研究为高活性In-Co催化剂体系在CO₂加氢反应中的催化机理及行为提供了解释,为金属-氧化铟(M-In₂O₃)催化剂体系的设计提供了参考.     

焙烧温度对K改性Ag-Fe/ZnO-ZrO2催化剂结构和CO加氢合成低碳混合醇醚性能的影响

采用并流共沉淀法在不同焙烧温度下制备K改性Ag-Fe/ZnO-ZrO₂催化剂,考察不同焙烧温度对催化剂CO加氢合成低碳混合醇醚反应性能的影响。通过N₂物理吸附(N₂-adsorption)、X射线衍射(XRD)、氢气程序升温还原(H₂-TPR)、一氧化碳程序升温脱附(CO-TPD)等手段对催化剂进行表征。结果表明,250 ℃焙烧的催化剂,由于焙烧温度较低,表面尚未形成足够多的活性位,未能达到最佳的催化性能;300 ℃焙烧的催化剂,其CO转化率最高、醇醚选择性较高,醇醚时空产率达到最大值。随着焙烧温度进一步升高,CO转化率逐渐降低,醇选择性先降低后增大,二甲醚(DME)选择性逐渐增大,醇醚时空产率逐渐降低。催化剂性能主要与其比表面积、还原性能、所含银铁复合物分散度及CO吸脱附性能有关,即比表面积较大、易于被还原、银铁复合物分散度较高以及较多的CO吸脱附活性位,有利于催化剂CO加氢转化。催化剂表面活性位对CO的非解离吸附强度降低,有利于醇醚产物的生成;而对CO的解离吸附强度增强,则不利于烃类产物的生成。     

In-Co二元金属氧化物上CO2催化加氢反应的选择性转变:催化反应的机理和构效关系

采用催化加氢的方式将CO₂转化为甲醇,既可以减少CO₂排放,又制备了化学品,该反应具有重要的研究意义.氧化铟(In₂O₃)作为CO2加氢制甲醇催化剂,由于其较高的CO₂活化能力和甲醇选择性,被科研工作者广泛研究.其中,将具有良好解离H2能力的过渡金属元素引入In₂O₃(M/In₂O₃)是有效提高催化剂性能的策略之一,然而,M/In₂O₃体系催化CO₂加氢反应机理及活性位点仍不清楚.本文引入Co制备了In-Co二元金属氧化物催化剂应用于CO2加氢制甲醇,结果表明,相较于In₂O₃,In-Co催化剂性能有很大提升,其中In1-Co₄催化剂上甲醇时空产率(9.7 mmol·g_cat^-1 h^-1)是In₂O₃(2.2 mmol·g_cat^-1 h^-1)的近5倍(反应条件:P=4.0 MPa,T=300℃,GHSV=24000 cm³ _STP g_cat^-1 h^-1,H2/CO₂=3).值得注意的是,尽管Co是金属元素的主体,In-Co催化剂中Co催化CO₂甲烷化的活性受到明显抑制.本文还通过多种技术系统研究了催化剂结构与反应选择性转变间的关系.采用电感耦合等离子体发射光谱、粉末X射线衍射、拉曼光谱、X射线光电子能谱和透射电子显微镜等对催化剂结构以及表面性质进行了表征.结果表明,在H₂还原气氛诱导下,In-Co催化剂表面发生重构,形成以CoO为核,以In₂O₃为壳的核壳结构,其在高压反应后仍能保持稳定;更重要的是,该核壳结构可以显著增强In-Co催化剂吸附及活化CO₂的能力.CO₂加氢反应动力学研究表明,Co催化剂上H₂分压对CO₂加氢为零级反应,而H₂分压在In-Co上的反应级数为正数;In-Co催化剂上,CO₂分压的反应级数接近于零,表明CO₂及其衍生物在In-Co的表面吸附饱和,但在纯Co上,则不会发生这种饱和吸附.通过原位DRIFTS研究了催化反应路径和关键中间物种的吸附及反应行为,发现CO₂加氢在纯Co和In-Co上的催化机理均遵循甲酸盐路径.在该催化路径中,CO₂首先加氢为甲酸盐(*HCOO)物种,随后加氢为甲氧基(*CH₃O).*CH₃O在Co催化剂上进一步加氢生成CH₄,而*CH₃O在In-Co催化剂上则会脱附生成CH₃OH.根据表征结果,本文认为,在还原性气氛下,In-Co发生了重构并生成表面富In₂O₃的核壳状结构,显著提高了催化剂对CO₂和含碳物种的吸附能力.Co和In-Co催化剂对CO₂加氢反应选择性的差异归因于催化剂对CO₂和对*HCOO等含碳中间物种的吸附稳定性不同.CO₂及其衍生的含碳中间物种在In-Co催化剂上的吸附能力比在Co催化剂上强,形成了较合适的催化剂表面C/H比,从而使*CH₃O能够脱附为CH₃OH,而不是进一步加氢为CH₄.综上,本文研究为高活性In-Co催化剂体系在CO₂加氢反应中的催化机理及行为提供了解释,为金属-氧化铟(M-In₂O₃)催化剂体系的设计提供了参考.     

经PPh3修饰的Rh/SiO2催化剂的吸附-脱附性能

 应用程序升温技术研究了氢甲酰化反应物CO,H2和C2H4在经PPh3修饰的Rh/SiO2(PPh3-Rh/SiO2)催化剂上的吸附-脱附行为. CO-TPD结果显示, Rh/SiO2催化剂在348, 398和525 K处有3个脱附峰, PPh3-Rh/SiO2催化剂仅在368 K处出现脱附峰,表明催化剂的吸附性能发生了明显变化. 采用原位红外光谱研究了PPh3-Rh/SiO2催化剂上CO的吸附态. 结果表明, 2040 cm-1处吸收峰归属于PPh3修饰的Rh粒子上线式吸附的CO. 这种吸附态既不同于Rh/SiO2多相催化剂表面Rh粒子上的CO吸附态,也不同于相应均相催化剂中的羰基配位态. TPD和FT-IR结果表明,在低压下PPh3-Rh/SiO2催化剂对氢甲酰化反应已具有相当的催化性能.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.