纳米碳纤维的表面性质和微结构对氧还原催化活性的影响

采用超声处理的方法分别对管式纳米碳纤维(t-CNF)和鱼骨式纳米碳纤维(f-CNF)进行了表面化学处理. XPS结果表明, 在混酸(浓硫酸+浓硝酸)和氨水中进行超声化学处理可以在CNF表面分别引入含氧官能团和含氮官能团. 电化学测试结果表明, 2种不同微结构CNF的氧还原催化活性都遵循相同的趋势, 即CNF-P相似文献   

硝酸改性活性炭上氧/氮官能团对脱汞性能的促进作用

采用硝酸氧化手段对活性炭进行了表面处理, 并在固定床反应器上测试了其脱除单质汞的性能. 研究表明, 在模拟烟气中硝酸改性活性炭能有效脱除单质汞. 采用元素分析、Brunauer-Emmett-Teller (BET)比表面积、扫描电子显微镜(SEM)、拉曼(Raman)光谱、Boehm滴定、程序升温脱附(TPD)和X射线光电子能谱(XPS)等手段研究了活性炭表面官能团对其脱汞性能的影响. 结果表明: 硝酸氧化处理能同时增加活性炭表面含氧官能团和含氮官能团的含量. 与改性活性炭的物理性质相比, 其化学性质对脱汞性能的影响更大, 单质汞主要被改性活性炭氧化为HgO而去除. 在脱汞反应中, 羰基、酯基和酸酐等含氧官能团可能是活性吸附位点, 反应后这些官能团被还原为羟基或者醚基; 而吡咯等含氮官能团可能是活性催化位点. 此外, 基于上述表征结果提出了硝酸改性活性炭表面官能团的脱汞机制.     

木材表面改性的XPS分析

利用微波等离子体对木材表面进行处理，并诱导引发接枝甲基丙烯酸甲酯；达到表面改性的效果以提高木质材料的性能，利用X射线光电子能谱(XPS)对木材表面改性前后的表面化学结构进行分析；结果表明：木材经微波等离子体处理，表面氧与碳的原子浓度比(no／nc)增加，产生大量的含氧官能团或过氧化物，从而引发木材与甲基丙烯甲酯单体产生接枝共聚反应。     

表面改性炭材料在微生物燃料电池中的应用(英)

研究了在空气阴极微生物燃料电池中修饰方法如硝酸处理和硝酸-氨水酸碱等对XC-72R作为阴极氧还原催化剂催化活性的影响,并且使用傅里叶变换红外光谱(FTIR)、Boehm滴定法和X射线光电子能谱(谱(XPS)等手段对催化剂进行了表征.FTIR测试证明硝酸处理可引入含氧基团氨水处理可引入含氮基团.另外,还测试了含有不同表面官能团的XC-72R对氧还原的活性,并将其作为阴极催化剂用在MFC中,测试了电池性能.实验表明,经酸碱修饰的XC-72R作为空气阴极MFC的催化剂具有很好的应用前景.     

聚甲基戊烯膜式氧合器表面碳酸酐酶的固定化及性能研究

聚甲基戊烯(PMP)膜式氧合器表面先用水等离子体改性,以引入羟基官能团;再以溴化氰为偶联剂,将碳酸酐酶(CA)偶联至其表面.改性后用X射线光电子能谱(XPS)、表面接触角及酶活性测定等方法研究PMP表面性能变化.结果表明,等离子体处理后,在PMP表面引入了大量的含氧官能团,与水的表面接触角从103.37°降低至50.01°.再将CA引入PMP表面后,与水的表面接触角进一步降低至39.23°;XPS的C1谱图中出现蛋白质的特征峰;以对硝基苯酚乙酸酯为底物,测得表面接枝CA的活性达到理论单分子层接枝活性的73%.改性后PMP表面物理化学性质的变化证明本文方法确实能成功地将羟基官能团、CA引入其表面.本方法有望应用在膜式氧合器上以提高其清除血液中CO2的能力.     

活性炭电极材料的表面改性和性能

以硝酸、双氧水、氨水三种化学试剂分别对活性炭进行表面改性, 用N2吸附法和FTIR表征炭材料改性前后孔结构和表面官能团的变化. 制备了以改性活性炭为电极材料, KOH溶液为电解质的模拟双电层电容器. 用恒流充放电、循环伏安、交流阻抗等方法考察了双电层电容器的电化学性能. 结果表明, 改性活性炭比表面积和平均孔径有所降低, 并且在炭材料表面引入了含氧或含氮官能团, 如—OH、>CO、—NH2等, 使炭材料的润湿性增强、电阻减小、电化学性能显著提高. 用65%硝酸改性后炭材料的比容量最高达到250 F·g-1, 比原样炭提高了72.4%; 实验电容器的漏电流急剧下降, 只有3-18 μA, 为原来电容器的漏电流(371 μA)的0.8%-4.9%.     

锂离子电池负极碳材料的表面改性与修饰：Ⅰ.表面的氧化,还原处理对碳…

通过各种氧化／还原体系对碳材料进行表面氧化，还原处理，研究了碳材料表面的痕量有机含氧官能团对以碳材料作为锂离子电池负极的电池性能的影响。结果表明，碳材料表面大量有机含氧官能团的存在将引起电池性能的严重恶化；相应地如对电极表面进行一定的还原处理，以减少碳表面有机官能团的含量及其氧化程度则可提高电极的容量及首次循环效率。     

炭载体改性对炭载Pd催化剂电催化性能的影响

研究了硝酸和氨水改性处理对活性炭表面基团、炭载Pd纳米粒子的形态及其对甲酸氧化电催化性能的影响.傅里叶变换红外(FT-IR)光谱、X射线光电子能谱(XPS)及Boehm滴定结果表明,硝酸和氨水处理分别增加了活性炭表面含氧基团和含氮基团的含量.透射电镜(TEM)及电化学测试显示,活性炭经硝酸处理后,表面负载的Pd粒子粒径降低,催化剂对甲酸氧化活性和稳定性提高.进一步用氨水处理后,Pd粒子的粒径没有明显变化,但催化剂中Pd0的含量增加,催化剂性能进一步提高.     

碳毡电极的表面改性——Ⅱ.碳毡表面HNO_3化学改性对电极性能影响

对碳毡表面HNO_3化学改性引起电极性能的变化进行较详细研究。物理分析数据表明,由于HNO_3氧化处理,碳毡表面亲水性含氧官能团含量增加及HNO_3分子易嵌入并吸引高温碳毡石墨层状结构中的电子使空穴增多,电极表面浸润性和导电性明显提高。碳毡比表面也因HNO_3腐蚀作用有所增加。另外,循环伏安分析结果指出,在表面改性电极上Cr~(3+)/Cr~(2+)及Fe~(3+)/Fe~(2+)反应电化学活性增强,不仅峰值电流I_(pa)、I_(pa)随HNO_3氧化时间增长明显加大,而且峰电位差△Ep(=E_(pa)-E_(pc))变小,反应更趋可逆。还因为催化剂Pb沉积量增加而提高了其催化活性,经HNO_3氧化处理后的碳毡表面更利于Cr~(3+)/Cr_(2+)反应进行,其I_(pa)、I_(pc)值的增加明显高于Fe~(3+)/Fe~(2+)反应。     

酸处理活性炭催化水合肼还原硝基苯(英文)

以水合肼为还原剂,采用硝酸、盐酸、硫酸及氮气或氢气氛处理的活性炭为催化剂,考察了其催化硝基苯还原反应性能.结果表明,经化学处理后,活性炭表面形成了各种含氧官能团,它们可引发水合肼分解,并影响硝基苯的吸附.活性炭表面形成的含氧官能团越多,其催化硝基苯还原速率越快.其中经盐酸处理的活性炭表面形成的含氧官能团最多,因而表现出最高的硝基苯还原活性.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。