Hydrogen storage over alkali metal hydride and alkali metal hydroxide composites

Alkali metal hydroxide and hydride composite systems contain both protic(H bonded with O) and hydridic hydrogen. The interaction of these two types of hydrides produces hydrogen. The enthalpy of dehydrogenation increased with the increase of atomic number of alkali metals,i.e.,-23 kJ/molH2 for LiOH-LiH, 55.34 kJ/molH2 for NaOH-NaH and 222 kJ/molH2 for KOH-KH. These thermodynamic calculation results were consistent with our experimental results. H2 was released from LiOH-LiH system during ball milling. The dehydrogenation temperature of NaOH-NaH system was about 150℃; whereas KOH and KH did not interact with each other during the heating process. Instead, KH decomposed by itself. In these three systems, NaOH-NaH was the only reversible hydrogen storage system, the enthalpy of dehydrogenation was about 55.65 kJ/molH2, and the corresponding entropy was ca. 101.23 J/(molH2 K), so the temperature for releasing 1.0 bar H2 was as high as 518℃, showing unfavorable thermodynamic properties. The activation energy for hydrogen desorption of NaOH-NaH was found to be57.87 kJ/mol, showing good kinetic properties.     

Controllable Hydrolysis Performance of MgLi Alloys and Their Hydrides

Theoretically, the hydrolysis of MgLi and MgH₂−LiH can produce 9.6 and 17.5 wt.% hydrogen (water is not included in the calculation), respectively. The ball-milling method is commonly used to refine the particle size and thus may improve hydrolysis kinetics. However, Mg and Li will be easily agglomerated, which means that direct ball-milling could not refine MgLi. In this work, we introduced 10 wt.% expanded graphite into the ball-milling process to synthesize refined MgLi alloy samples. Further studies showed that MgLi-10 wt.% expanded graphite can produce 966 mL/g hydrogen within 3 min in 0.5 M MgCl₂ solution. The MgLi hydrides were synthesized by reactive ball milling under 3 MPa H₂ and their hydrolysis performance was investigated. Moreover, the sawed powder was milled in 3 MPa H₂ for 6 h and then hydrogenated in 3 MPa H₂ at 380 °C; it can produce 1542 and 1773 mL/g (15.8 wt.%) hydrogen in 5 and 30 min with mild kinetics, respectively, and the activation energy of the hydrolysis reaction is 24.6 kJ/mol in 1 M MgCl₂ solution. The findings here open a new avenue to the development of refined MgLi alloys and hydrides for hydrogen generation through a controllable hydrolysis process.     

In situ Investigations on the Formation and Decomposition of KSiH3 and CsSiH3

The system KSi‐KSiH₃ stores 4.3 wt % of hydrogen and shows a very good reversibility at mild conditions of 0.1 MPa hydrogen pressure and 414 K. 1 We followed the reaction pathways of the hydrogenation reactions of KSi and its higher homologue CsSi by in situ methods in order to check for possible intermediate hydrides. In situ diffraction at temperatures up to 500 K and gas pressures up to 5.0 MPa hydrogen gas for X‐ray and deuterium gas for neutron reveal that both KSi and CsSi react in one step to the hydrides KSiH₃ and CsSiH₃ and the respective deuterides. Neither do the Zintl phases dissolve hydrogen (deuterium), nor do the hydrides (deuterides) show any signs for non‐stoichiometry, i.e. all phases involved in the formation are line phases. Heating to temperatures above 500 K shows that at 5.0 MPa hydrogen pressure only the reaction 2CsSi + 3H₂ = 2CsSiH₃ is reversible. Under these conditions, KSiH₃ decomposes to a clathrate and potassium hydride according to 46KSiH₃ = K₈Si₄₆ + 38KH + 50H₂.     

Nickel hydrogen gas batteries: From aerospace to grid-scale energy storage applications

The challenging requirements of high safety, low-cost, all-climate and long lifespan restrict most battery technologies for grid-scale energy storage. Historically, owing to stable electrode reactions and robust battery chemistry, aqueous nickel–hydrogen gas (Ni–H₂) batteries with outstanding durability and safety have been served in aerospace and satellite systems for over three decades ever since their first development in the 1970s. Despite their satisfactory performances, this technology has difficulty to be applied for grid-scale energy storage primarily because of their high cost resulting from the utilization of expensive platinum as anode hydrogen catalyst. In recent years, with the extensive exploration of inexpensive hydrogen evolution/oxidation reaction catalysts, advanced Ni–H₂ batteries have been revived as promising battery chemistry for grid-scale energy storage applications. This mini-review provides an overview of the development activities of Ni–H₂ batteries and highlights the recent advances in the application of advanced Ni–H₂ batteries for grid-scale energy storage. New cost-effective hydrogen evolution/oxidation reactions catalysts, novel cathode materials, and advanced Ni–H₂ battery designs toward further development of Ni–H₂ batteries are discussed. The renaissance of advanced Ni–H₂ battery technology is particularly attractive for future grid-scale energy storage applications.     

ChemInform Abstract: First‐Principles Screening of Complex Transition Metal Hydrides for High Temperature Applications.

Semi‐automated thermodynamic and phase diagram calculations based on DFT and grand canonical linear programming (GCLP) methods are used to screen 102 ternary and quaternary complex transition metal hydrides (CTMHs) and 26 ternary saline hydrides in a library of over 260 metals, intermetallics, binary, and higher hydrides to identify materials that release H₂ at higher temperatures than the associated binary hydrides and at elevated temperatures (T < 1000 K, 1 bar H₂ overpressure).     

Strategies for the Improvement of the Hydrogen Storage Properties of Metal Hydride Materials

Metal hydrides are an important family of materials that can potentially be used for safe, efficient and reversible on‐board hydrogen storage. Light‐weight metal hydrides in particular have attracted intense interest due to their high hydrogen density. However, most of these hydrides have rather slow absorption kinetics, relatively high thermal stability, and/or problems with the reversibility of hydrogen absorption/desorption cycling. This paper discusses a number of different approaches for the improvement of the hydrogen storage properties of these materials, with emphasis on recent research on tuning the ionic mobility in mixed hydrides. This concept opens a promising pathway to accelerate hydrogenation kinetics, reduce the activation energy for hydrogen release, and minimize deleterious possible by‐products often associated with complex hydride systems.     

An Analytical Bond Order Potential for Mg−H Systems

Magnesium-based materials provide some of the highest capacities for solid-state hydrogen storage. However, efforts to improve their performance rely on a comprehensive understanding of thermodynamic and kinetic limitations at various stages of (de)hydrogenation. Part of the complexity arises from the fact that unlike interstitial metal hydrides that retain the same crystal structures of the underlying metals, MgH₂ and other magnesium-based hydrides typically undergo dehydrogenation reactions that are coupled to a structural phase transformation. As a first step towards enabling molecular dynamics studies of thermodynamics, kinetics, and (de)hydrogenation mechanisms of Mg-based solid-state hydrogen storage materials with changing crystal structures, we have developed an analytical bond order potential for Mg−H systems. We demonstrate that our potential accurately reproduces property trends of a variety of elemental and compound configurations with different coordinations, including small clusters and bulk lattices. More importantly, we show that our potential captures the relevant (de)hydrogenation chemical reactions 2H (gas)→H₂ (gas) and 2H (gas)+Mg (hcp)→MgH₂ (rutile) within molecular dynamics simulations. This verifies that our potential correctly prescribes the lowest Gibbs free energies to the equilibrium H₂ and MgH₂ phases as compared to other configurations. It also indicates that our molecular dynamics methods can directly reveal atomic processes of (de)hydrogenation of the Mg−H systems.     

Boron Hydrogen Compounds: Hydrogen Storage and Battery Applications

About 25 years ago, Bogdanovic and Schwickardi (B. Bogdanovic, M. Schwickardi: J. Alloys Compd. 1–9, 253 (1997) discovered the catalyzed release of hydrogen from NaAlH₄. This discovery stimulated a vast research effort on light hydrides as hydrogen storage materials, in particular boron hydrogen compounds. Mg(BH₄)₂, with a hydrogen content of 14.9 wt %, has been extensively studied, and recent results shed new light on intermediate species formed during dehydrogenation. The chemistry of B₃H₈⁻, which is an important intermediate between BH₄⁻ and B₁₂H₁₂²⁻, is presented in detail. The discovery of high ionic conductivity in the high-temperature phases of LiBH₄ and Na₂B₁₂H₁₂ opened a new research direction. The high chemical and electrochemical stability of closo-hydroborates has stimulated new research for their applications in batteries. Very recently, an all-solid-state 4 V Na battery prototype using a Na₄(CB₁₁H₁₂)₂(B₁₂H₁₂) solid electrolyte has been demonstrated. In this review, we present the current knowledge of possible reaction pathways involved in the successive hydrogen release reactions from BH₄⁻ to B₁₂H₁₂²⁻, and a discussion of relevant necessary properties for high-ionic-conduction materials.     

铁脂质体/水分配系数测定及影响因素考察

基于PAF-301分子模型通过Li 掺杂或B取代等模式设计了几种新型多孔芳香骨架(PAFs)材料, 采用量子力学和分子力学方法对新材料的储氢性能进行研究. 由量子力学计算得到了不同分子片段与H₂之间的结合能, 并结合DDEC方法计算了各分子片段的原子电荷分布. 利用巨正则蒙特卡洛(GCMC)模拟方法计算了77和298 K下H₂在不同PAFs材料中的吸附平衡性质. 结果表明, H₂直接与苯环的结合能较低, 但掺杂Li 原子能够提高H₂与六元环的结合能, 同时Li 原子体现出较高的正电性质, B原子取代苯环中的两个C原子后, 使得原有C原子电负性增强; 77 K下PAF-301Li 具有最高的储氢性能, 而PAF-C₄B₂H₄-Li₂-Si 和PAF-C₄B₂H₄-Li₂-Ge体现出较好的常温储氢性能, 各种材料的常温储氢性能远低于其低温储氢性能. 通过77 K下H₂在PAFs材料中的等位能面分布和吸附平衡质心密度分布对H₂在PAFs 材料中的优先吸附位置进行分析, 发现在PAF-301 和PAF-301Li 骨架中, 由于中心能量较低的等位能区域范围较宽, H₂在其中存在四个明显的吸附高密度分布区域, 而其它三种PAFs晶胞中心能量较低的等位能区域范围较窄, 使得H₂在其中只存在两个明显的吸附高密度分布区域.     

H2S‐Mediated Thermal and Photochemical Methane Activation

Sustainable, low‐temperature methods for natural gas activation are critical in addressing current and foreseeable energy and hydrocarbon feedstock needs. Large portions of natural gas resources are still too expensive to process due to their high content of hydrogen sulfide gas (H₂S) mixed with methane, deemed altogether as sub‐quality or “sour” gas. We propose a unique method of activation to form a mixture of sulfur‐containing hydrocarbon intermediates, CH₃SH and CH₃SCH₃, and an energy carrier such as H₂. For this purpose, we investigated the H₂S‐mediated methane activation to form a reactive CH₃SH species by means of direct photolysis of sub‐quality natural gas. Photoexcitation of hydrogen sulfide in the CH₄+H₂S complex resulted in a barrierless relaxation by a conical intersection to form a ground‐state CH₃SH+H₂ complex. The resulting CH₃SH could further be coupled over acidic catalysts to form higher hydrocarbons, and the resulting H₂ used as a fuel. This process is very different from conventional thermal or radical‐based processes and can be driven photolytically at low temperatures, with enhanced control over the conditions currently used in industrial oxidative natural gas activation. Finally, the proposed process is CO₂ neutral, as opposed to the current industrial steam methane reforming (SMR).     

Complex surface analytical investigations on hydrogen absorption and desorption processes of a TiMn<Subscript>2</Subscript>-based alloy

Metal hydrides are one of the most promising technologies in the field of hydrogen storage due to their high volumetric storage density. Important reaction steps take place at the very surface of the solid during hydrogen absorption. Since these reaction steps are drastically influenced by the properties and potential contamination of the solid, it is very important to understand the characteristics of the surface, and a variety of analytical methods are required to achieve this. In this work, a TiMn₂-type metal hydride alloy is investigated by means of high-pressure activation measurements, X-ray photoelectron spectroscopy (XPS), secondary neutral mass spectrometry (SNMS) and thermal desorption mass spectrometry (TDMS). In particular, TDMS is an analytical tool that, in contrast to SIMS or SNMS, allows the hydrogen content in a metal to be quantified. Furthermore, it allows the activation energy for desorption to be determined from TDMS profiles; the method used to achieve this is presented here in detail. In the results section, it is shown that the oxide layer formed during manufacture and long-term storage prevents any hydrogen from being absorbed, and so an activation process is required. XPS measurements show the oxide states of the main alloy elements, and a layer 18 nm thick is determined via SNMS. Furthermore, defined oxide layers are produced and characterized in UHV using XPS. The influence of these thin oxide layers on the hydrogen sorption process is examined using TDMS. Finally, the activation energy of desorption is determined for the investigated alloy using the method presented here, and values of 46 kJ/mol for hydrogen sorbed in UHV and 103 kJ/mol for hydrogen originating from the manufacturing process are obtained.     

Computational modeling of green hydrogen generation from photocatalytic H2S splitting: Overview and perspectives

Hydrogen plays an important role in developing a clean and sustainable future energy scenario. Substantial efforts to produce green hydrogen from water splitting, biomass and hydrogen sulfide (H₂S) have been made in recent years. H₂S, naturally occurring or generated in fuel gas processing and industrial wastewater treatment, can be split into hydrogen and sulfur via photocatalysis. Although it is not as widely used as water splitting for green hydrogen production, this process is considered to be an appropriate and sustainable way to meet the future energy demands, adding value to H₂S. Therefore, it is essential to understand how to improve the solar light utilization and splitting efficiency of H₂S based on the existing technology and materials. Along with that effort, molecular modeling and theoretical calculations are indispensable tools to provide guidance to effectively design photocatalysts for improving hydrogen generation efficiency. In this review, we summarize the published work on H₂S photocatalysis modeling and illustrate the use of different computational methods to gain more in-depth insight into the reaction mechanisms and processes. Moreover, an overview of quantum mechanical and molecular simulation approaches combined with other modeling techniques, relevant to material science and catalysis design and applicable to H₂S splitting is also presented. Challenges and future directions for developing H₂S splitting photocatalysts are highlighted in this contribution, which is intended to inspire further simulation developments and experiments for H₂S splitting, tailoring photocatalysts design towards highly efficient hydrogen production.     

孔性介质负载下的络合氢化物及其储氢特性*

络合氢化物具有较高的重量储氢密度,已成为国内外研究的热点。孔性介质由于高比表面积、孔径均匀可调以及良好热稳定性而备受关注。研究表明,实现孔性介质负载的络合氢化物可有效地改善其储氢性能。本文简述了孔性介质的结构特征和物化特性,着重阐述了孔性介质负载催化络合氢化物的制备方法、脱/加氢性能的影响及其催化机理的研究进展,并指出了需要研究的科学问题。     

Recent research progress of bimetallic phosphides-based nanomaterials as cocatalyst for photocatalytic hydrogen evolution

Hydrogen energy（H2） has been considered as the most possible consummate candidates for replacing the traditional fossil fuels because of its higher combustion heat value and lower environmental pollution.Photocatalytic hydrogen evolution（PHE） from water splitting based on semiconductors is a promising technology towards converting solar energy into sustainable H2fuel evolution. Developing high-activity and abundant source semiconductor materials is particularly important to realize highly effici...     

Calorimetric enthalpies of formation and decomposition of hydrides of ZrMn2, ZrCr2, and related systems

Integral enthalpies of absorption and desorption of hydrogen by hyperstoichiometric ZrMn₂T_0.8 (T = Mn, Fe, Co, Ni, and Cu) and stoichiometric ZrMn₂- and ZrCr₂-based alloys have been determined. The measured enthalpies range from ～24 to ～41 kJ/mole H₂. The ΔH values for hydrides formed by the series of metallic hosts ZrMn₂T_0.8 are smaller than that for ZrMn₂, accounting for the enhanced dissociation pressures of the ZrMn₂T_0.8 hydrides. In the series of ZrMn₂T_0.8 hydrides there is a pronounced minimum for hydride of ZrMn₂Co_0.8, accounting for the extraordinarily high decomposition pressure of this system. Site occupancies, provided by published neutron diffraction studies, were used to calculate configurational entropies of ZrCr₂ hydrides and related systems. Results obtained were in fair agreement with experiment.     

Hydrides of intermetallic compounds with a H/M ratio greater than unity obtained at high hydrogen pressures

Novel hydride phases with H/M > 1 based on Zr₂Pd, Hf₂Pd, and Hf₂Cu (structures of the MoSi₂, type) have been synthesized at high H₂ pressures. The X-ray diffraction investigations of the resulting hydrides have been carried out. Some factors determining the maximum hydrogen content in the hydrides of intermetallic compounds are discussed. A model structure of the hydrides obtained is proposed, which assumes the possibility of direct H-H interactions when the interatomic distances are less than 1 Å.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 843–845, May, 1993.     

Palladium electrodeposits: Dependence of structure and sorption properties on the deposition potential

A series of Pd electrodeposits (edPd) on Pt substrates is prepared at deposition potentials of -0.05 to 0.55 V with respect to a reversible hydrogen electrode in 0.5 M H₂SO₄. Their nanostructure is characterized by scanning tunneling microscopy. The size distribution of particles is estimated, and dependences of its maximum and half width on the deposition potential are determined. A comparative coulometric study of adsorption of copper and oxygen on edPd shows that real surface areas determined from these data substantially differ. The average size of particles for edPd, estimated within the model of equal-size spheres, is shown to be incorrect. The assumption that particles in the deposits essentially coalesce is substantiated. It is shown that the equilibrium hydrogen content in thea and β hydrides is anomalously high for the deposits whose growth was accompanied by deep hydrogenation of Pd. At a given effective pressure, for the α-phase, this value is always substantially higher as compared with less defective materials. In the β-phase, the hydrogen concentration can be either lower or higher     

Influence of Defects on the Stability and Hydrogen-Sorption Behavior of Mg-Based Hydrides

This review deals with the destabilization methods for improvement of storage properties of metal hydrides. Both theoretical and experimental approaches were used to point out the influence of various types of defects on structure and stability of hydrides. As a case study, Mg, and Ni based hydrides has been investigated. Theoretical studies, mainly carried out within various implementations of DFT, are a powerful tool to study mostly MgH₂ based materials. By providing an insight on metal-hydrogen bonding that governs both thermodynamics and hydrogen kinetics, they allow us to describe phenomena to which experimental methods have a limited access or do not have it at all: to follow the hydrogen sorption reaction on a specific metal surface and hydrogen induced phase transformations, to describe structure of phase boundaries or to explain the impact of defects or various additives on MgH₂ stability and hydrogen sorption kinetics. In several cases theoretical calculations reveal themselves as being able to predict new properties of materials, including the ways to modify Mg or MgH₂ that would lead to better characteristics in terms of hydrogen storage. The influence of ion irradiation and mechanical milling with and without additives has been discussed. Ion irradiation is the way to introduce a well-defined concentration of defects (Frankel pairs) at the surface and sub-surface layers of a material. Defects at the surface play the main role in sorption reaction since they enhance the dissociation of hydrogen. On the other hand, ball-milling introduce defects through the entire sample volume, refine the structure and thus decrease the path for hydrogen diffusion. Two Severe Plastic Deformation techniques were used to better understand the hydrogenation/dehydrogenation kinetics of Mg- and Mg₂Ni-based alloys: Equal-Angular-Channel-Pressing and Fast-Forging. Successive ECAP passes leads to refinement of the microstructure of AZ31 ingots and to instalment therein of high densities of defects. Depending on mode, number and temperature of ECAP passes, the H-sorption kinetics have been improved satisfactorily without any additive for mass H-storage applications considering the relative speed of the shaping procedure. A qualitative understanding of the kinetic advanced principles has been built. Fast-Forging was used for a “quasi-instantaneous” synthesis of Mg/Mg₂Ni-based composites. Hydrogenation of the as-received almost bi-phased materials remains rather slow as generally observed elsewhere, whatever are multiple and different techniques used to deliver the composite alloys. However, our preliminary results suggest that a synergic hydrogenation / dehydrogenation process should assist hydrogen transfers from Mg/Mg₂Ni on one side to MgH₂/Mg₂NiH₄ on the other side via the rather stable a-Mg₂NiH_0.3, acting as in-situ catalyser.     

Computational design of tetrahedral silsesquioxane-based porous frameworks with diamond-like structure as hydrogen storage materials

A novel type of three-dimensional (3D) tetrahedral silsesquioxane-based porous frameworks (TSFs) with diamond-like structure was computationally designed using the density functional theory (DFT) and classical molecular mechanics (MM) calculations. The hydrogen adsorption and diffusion properties of these TSFs were evaluated by the methods of grand canonical Monte Carlo (GCMC) and molecular dynamics (MD) simulations. The results reveal that all designed materials possess extremely high porosity (87–93 %) and large H₂ accessible surface areas (5,268–6,544 m² g^?1). Impressively, the GCMC simulation results demonstrate that at 77 K and 100 bar, TSF-2 has the highest gravimetric H₂ capacity of 29.80 wt%, while TSF-1 has the highest volumetric H₂ uptake of 65.32 g L^?1. At the same time, the gravimetric H₂ uptake of TSF-2 can reach up to 4.28 wt% at the room temperature. The extraordinary performances of these TSF materials in hydrogen storage made them enter the rank of the top hydrogen storage materials so far.     

氢分子与超氧阴离子自由基反应的微观机理

为了认识氢气生物学效应的分子机制,采用量子化学的M06-2X/6-311+G(d,p)和CCSD(t)/aug-cc-pVTZ方法模拟了人体条件(310K、液相)下氢分子与超氧阴离子自由基的反应机理。研究表明,反应的吉布斯自由能变化值为117.2kJ·mol~(-1),活化自由能垒为156.2kJ·mol~(-1),从热力学及动力学角度该反应都不容易进行。然后从电子结构和轨道作用层面对反应的微观机制进行了探讨,发现从反应物变为过渡态过程中,复合物轨道的组成和轨道能级发生显著变化(尤其是第8号轨道能级升高最多,达到2.73eV),O~-_2片段向H_2片段的电子转移数增加了0.1760个,并且转移的电子主要集居于第8号轨道,这削弱了H_2片段两个H原子间的化学键,也是反应活化能的主要来源。