Phosphonate‐terminated poly(vinyl acetate) synthesized by RAFT/MADIX polymerization

Four different xanthates containing either phosphonate or bisphosphonate moieties were synthesized with high degree of purity. These xanthates were used as chain transfer agents (CTA) in the RAFT/MADIX polymerization of vinyl acetate (VAc) to prepare end‐capped poly(VAc). The rate of VAc polymerization in the presence of these new CTAs was shown to be similar to that obtained with conventional xanthate, that is, (methyl ethoxycarbonothioyl) sulfanyl acetate. Good control of VAc polymerization was also obtained since the molecular weight increased linearly with monomer conversion for each phosphonate‐containing xanthate. Low‐PDI values were obtained, ascribed to efficient exchange during RAFT/MADIX polymerization. C_ex value was therefore calculated to about 25, based on RAFT/MADIX of VAc in the presence of rhodixan A1/VAc adduct. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Investigation of the influence of the architectures of poly(vinyl pyrrolidone) polymers made via the reversible addition–fragmentation chain transfer/macromolecular design via the interchange of xanthates mechanism on the stabilization of suspension polymerizations

Linear, star, and block copolymers based on poly(vinyl pyrrolidone) (PVP) were synthesized with the macromolecular design via the interchange of xanthates (MADIX) process for use as potential stabilizers in suspension polymerization. The design of the leaving group of the dithioxanthate‐based transfer agent was shown to be key to the successful preparation of well‐defined PVP architectures. A linear correlation of the monomer conversion and molecular weight was found in the synthesis of star polymers, whereas the molecular weight distribution remained narrow (polydispersity index < 1.3). Significant side reactions, which typically broaden the molecular weight distribution when R‐designed MADIX agents are used, were absent. The living behavior of the PVP polymerization was furthermore confirmed via chain extension with vinyl acetate, which resulted in the formation of PVP–PVAc block copolymers [where PVAc is poly(vinyl acetate)]. The prepared polymers were used as stabilizers in suspension polymerization to prepare crosslinked poly(vinyl neodecanoate)/ethylene glycol dimethacrylate microspheres. The ratio of the interfacial tension of the aqueous and monomer phases and the overall viscosity were found to have an effect on the diameter of the particles, with PVP star polymers as stabilizers resulting in smaller particles. A smaller interfacial tension, measured when star polymers and block copolymers were used, resulted in the appearance of smaller particles, probably because of more breakup events of the monomer droplets and the enhanced stabilization of the particle surface area. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4372–4383, 2006     

Synthesis of diblock copolymers containing poly(N‐vinylcarbazole) by reversible addition‐fragmentation chain transfer polymerization

The reversible addition‐fragmentation chain transfer (RAFT) polymerization of N‐vinylcarbazole (NVK) mediated by macromolecular xanthates was used to prepare three types of block copolymers containing poly(N‐vinylcarbazole) (PVK). Using a poly(ethylene glycol) monomethyl ether based xanthate ( PEG‐X ), the RAFT polymerization of NVK proceeded in a controlled way to afford a series of PEG‐b‐PVK with different PVK chain lengths. Successive RAFT polymerization of NVK and vinyl acetate (VAc) with a small molecule xanthate ( X1 ) as the chain transfer agent was tested to prepare PVK‐b‐PVAc. Though both monomers can be homopolymerized in a controlled manner with this xanthate, only by polymerizing NVK first could give well‐defined block copolymers. The xanthate groups in the end of PVK could be removed by radical‐induced reduction using tributylstannane, and PVK‐b‐PVA was obtained by further hydrolysis of PVK‐b‐PVAc under basic conditions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characters of hyperbranched poly(vinyl acetate) by RAFT polymeraztion

Reversible addition-fragmentation chain transfer (RAFT) polymerization of VAc in the presence of ECTVA, which capable of both reversible chain transferable through a xanthate moiety and propagation via a vinyl group, led to highly branched copolymers by a method analogous to self-condensing vinyl polymerization (SCVP). The ECTVA acted as a vinyl acetate AB^∗ inimer. It was copolymerized with vinyl acetate (VAc) in ratios selected to tune the distribution and length of branches of resulting hyperbranched poly(vinyl acetate). The degree of branching increased with chain ECTVA concentration, as confirmed by NMR spectroscopy. The polymer structure was characterized via MALDI–TOF. Retention of the xanthate compound during the polymerization was evidenced by successful chain extension of a branched (PVAc) macroCTA by RAFT polymerization. The branched PVAc led to better dissolution as compared to linear PVAc, an effect attributed primarily to an increased contribution of end groups.     

Synthesis of high-molecular-weight poly(vinyl alcohol) with high yield by novel one-batch suspension polymerization of vinyl acetate and saponification

Generally, owing to tautomerism of vinyl alcohol monomer, poly(vinyl alcohol) (PVA) cannot be obtained by direct polymerization but it can be obtained by the saponification of poly(vinyl ester) precursors such as poly(vinyl acetate) (PVAc). In this study, to obtain high-molecular-weight (HMW) PVA with high yield through a one-batch method, we tried continuous saponification of PVAc prepared by suspension polymerization of vinyl acetate (VAc). We controlled various polymerization conditions, such as polymerization temperature, initiator concentration, suspending agent concentration, agitation speed, and VAc/water ratio, and obtained PVAc with a maximum conversion of VAc into PVAc of over 95-98%. PVA beads having various molecular parameters were prepared by continuous saponification of PVAc microspheres. Despite our employing a one-batch process, a maximum degree of saponification of 99.9% could be obtained. Continuous heterogeneous saponification of prepared PVAc yielded HMW PVA having a number-average degree of polymerization of 2,500-5,500, a syndiotactic diad content of 51-52%, and degree of saponification of 85.0-99.9%.     

Synthesis and Characterization of Poly(N-isopropylacrylamide) and Poly(vinyl acetate) Diblock Copolymers via MADIX Process

The synthesis of diblock copolymers of poly(N-isopropylacrylamide) (PNIPAM) and poly(vinyl acetate) (PVAc) was performed by macromolecular design via interchange of xanthates (MADIX) process. Following the preparation of methyl (isopropoxycarbonothioyl) sulfanyl acetate (MIPCTSA) as chain transfer agent, it was reacted with vinyl acetate to obtain PVAc macro-chain transfer agent. Then, block copolymerization was completed by successive addition of N-isopropylacrylamide (NIPAM). ¹H NMR spectroscopy confirmed the presence of both blocks in the copolymer structure, with the expected composition based on the feed ratio. Size Exclusion Chromatography (SEC) was used to investigate the relative values of molecular characteristics. Only 20% of PVAc was converted to block copolymer. The resultant block copolymer structures were further examined in terms of their morphologies as well as critical micelle concentration (CMC) by using ESEM and Fluorescence Excitation Spectroscopic techniques, respectively. Morphological characterization confirmed amphiphilic block copolymer formation with the existence of mainly ca. 100 nm well distributed micelles. The thermo responsive amphiphilic behavior of the block copolymer solutions were followed by Dynamic Light Scattering (DLS) technique.     

Synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers by combining ATRP and RAFT polymerizations

The synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers using a combination of two living radical polymerization techniques, atom transfer radical polymerization (ATRP) and reversible addition‐fragmentation chain transfer (RAFT) polymerization, is reported. The use of two methods is due to the disparity in reactivity of the two monomers, viz. vinyl acetate is difficult to polymerize via ATRP, and a suitable RAFT agent that can control the polymerization of vinyl acetate is typically unable to control the polymerization of tert‐butyl acrylate. Thus, ATRP was performed to make poly(tert‐butyl acrylate) containing a bromine end group. This end group was subsequently substituted with a xanthate moiety. Various spectroscopic methods were used to confirm the substitution. The poly(tert‐butyl acrylate) macro‐RAFT agent was then used to produce (tert‐butyl acrylate‐block‐vinyl acetate). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7200–7206, 2008     

Low temperature suspension polymerization of vinyl acetate using 2,2′-azobis(2,4-dimethylvaleronitrile) for the preparation of high molecular weight poly(vinyl alcohol) with high yield

 To obtain high molecular weight (HMW) poly(vinyl acetate) (PVAc) with high conversion and high linearity for a precursor of HMW poly(vinyl alcohol) (PVA), vinyl acetate (VAc) was suspension-poly-merized using a low-temperature initiator, 2,2′-azobis (2,4-dimethyl-valeronitrile) (ADMVN), and the effects of polymerization conditions on the polymerization behavior and molecular structures of PVAc and PVA prepared by saponifying PVAc were investigated. On the whole, the experimental results well corres-ponded to the theoretically predicted tendencies. Suspension polymerization was slightly inferior to bulk polymerization in increasing molecular weight of PVA. In contrast, the former was absolutely superior to the latter in increasing conversion of the polymer, which indicated that the suspension polymerization rate of VAc was faster than the bulk one. These effects could be explained by a kinetic order of ADMVN concentration calculated by initial-rate method and an activation energy difference of polymerization obtained from the Arrhenius plot. Suspension polymerization at 30 °C by adopting ADMVN proved to be successful in obtaining PVA of HMW (number-average degree of polymerization (P _n)): (4200–5800) and of high yield (ultimate conversion of VAc into PVAc: 85–95%) with diminishing heat generated during polymerization. In the case of bulk polymerization of VAc at the same conditions, maximum P _n and conversion of 5200–6200 and 20–30% was obtained, respectively. The P _n, lightness, and syndiotacticity were higher with PVA prepared from PVAc polymerized at lower temperatures. Received: 10 February 1998 Accepted: 15 April 1998     

Preparation of a xanthate‐terminated dextran by click chemistry: Application to the synthesis of polysaccharide‐coated nanoparticles via surfactant‐free ab initio emulsion polymerization of vinyl acetate

Stable monodisperse poly(vinyl acetate) (PVAc) submicronic latex particles were synthesized by ab initio batch emulsion polymerization using a dextran derivative from renewable resource as an efficient steric stabilizer. The dextranend‐functionalized by a xanthate moiety was synthesized by Huisgen's 1,3‐dipolar cycloaddition (click chemistry). It was applied as a macromolecular RAFT (reversible addition fragmentation chain transfer) agent in surfactant‐free emulsion polymerization of vinyl acetate to form in situ an amphiphilic block copolymer able to efficiently stabilize the latex particles. The method afforded the preparation of high solids content (27%) latices coated by dextran. Both the kinetic study and the molar mass analyses confirmed the involvement of the dithiocarbonate group in the emulsion polymerization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2845–2857, 2008     

Synthesis of poly(vinyl acetate) with fluorescence via a combination of RAFT/MADIX and “click” chemistry

A novel ω-azido-functionalized RAFT reagent, O-(2-azido-ethyl) S-benzyl dithiocarbonate (AEBDC), was synthesized and subsequently employed to mediate the reversible addition-fragmentation chain transfer (RAFT) polymerization of vinyl acetate (VAc) to prepare end-functionalized polymers. The polymerization results showed that the RAFT polymerizations of VAc could be well controlled using AEBDC as the RAFT agent. Number-average molecular weights (M_n GPC) increased linearly with monomer conversion, and molecular weight distributions were relatively narrow. ¹H NMR spectrum of the poly(vinyl acetate) (PVAc) confirmed the existence of functional azido group at the end of the polymers chains. The ω-azido-terminated polymers were coupled by “click” chemistry with a fluorescent alkyne, 7-propinyloxy coumarin, to prepare fluorescent PVAc. The fluorescence properties of the PVAc homopolymers before and after coupling with 7-propinyloxy coumarin in CH₂Cl₂ solution were investigated.     

致孔剂对HP（MA—VAc—MMA）载体孔结构的影响

以二乙烯苯和双丙烯酸多缩乙二醇酯为交联剂、聚醋酸乙烯酯（ＰＶＡｃ）或它与醋酸丁酯（ＢＡＣ）的混合物为致孔剂、ＢＰＯ为引发剂，用悬浮聚合随后水解的方法制得了部分水解聚（丙烯酸甲酯－醋酸乙烯酯－甲基丙烯酸甲酯）［ＨＰ（ＭＡ－ＶＡｃ－ＭＭＡ）］多孔载体，研究了ＰＶＡｃ及（ＰＶＡｃ＋ＢＡＣ）用量、分子量及混合比对ＨＰ（ＭＡ－ＶＡｃ－ＭＭＡ）孔结构的影响。结果表明，当ＰＶＡｃ的Ｍ＞２．５×１０５，ＰＶＡｃ／ＢＡＣ为２．３，用量为１０～２０％时，可制得孔隙率较高，孔径分布较窄，孔表面积较大的多孔载体。这种载体适用于微生物固定化。     

Poly(vinyl alcohol) star polymers prepared via MADIX/RAFT polymerisation

Poly(vinyl acetate) stars were prepared using MADIX/RAFT polymerisation mediated by xanthates. The polymerisation shows living characteristics with molecular weight increasing with conversion. The subsequent hydrolysis of these three and four arm stars led to the formation of poly(vinyl alcohol) stars.     

Surface-initiated living radical polymerization from silica particles functionalized with poly(ethylene glycol)-carrying initiator

A novel yet versatile approach is described for surface-initiated living radical polymerization (SI-LRP) from silica particles (SiPs). Monodisperse SiPs were surface-modified with a newly designed surface-fixable initiator (BPEGE) having three components: a triethoxysilane moiety, a poly(ethylene glycol) (PEG) unit, and an initiation site for atom transfer radical polymerization (ATRP) in the form of a 2-bromoisobutyryl group. The surface-initiated ATRP of methyl methacrylate (MMA) mediated by a copper complex was carried out with the BPEGE-fixed SiPs. The polymerization proceeded in a living manner, producing SiPs coated with well-defined poly(MMA) of a target molecular weight with a graft density as high as 0.5 chains/nm². Thanks to the amphiphilic property of PEG, the system was successfully applied for SI-ATRP of PEG methacrylate and sodium p-styrenesulfonate in aqueous media in which the BPEGE-fixed SiPs were highly dispersed without causing any aggregations. The formation of colloidal crystals with the polymer brush-afforded SiPs demonstrated the high uniformity and perfect dispersibility of the hybrid particles.     

Radiation induced graft polymerization of multi-walled carbon nanotubes for superhydrophobic composite membrane preparation

Highly soluble multi-walled carbon nanotubes (MWNTs) were prepared by radiation-induced free radical graft polymerization of vinyl acetate (VAc) onto pristine MWNT surfaces. High resolution transmission electron microscopy (HR-TEM), Fourier transform infrared (FTIR) spectroscopy, and micro-Raman spectroscopy were used to confirm that poly(vinyl acetate) (PVAc) had been successfully grafted onto the surface of the MWNTs. The effects of experimental parameters on the degree of grafting (DG) of PVAc were also investigated, including adsorbed dose, dose rate, initial monomer concentration, and solvents. The grafted MWNTs (MWNTs-g-PVAc) exhibited good solubility in common organic solvents at high mass fraction. In addition, a superhydrophobic composite membrane could be readily fabricated by vacuum filtration of MWNTs-g-PVAc onto a supporting membrane, as was confirmed by water contact angle testing and visualization by scanning electron microscopy.     

Preparation and biodegradation of sugar-containing poly(vinyl acetate) emulsions

To accelerate the biodegradability of poly(vinyl acetate)-based emulsions, emulsion copolymerizations of vinyl sugars, including triacetylated N-acetyl-D-glucosamine (GlcNAc)-substituted 2-hydroxyethyl methacrylate (GlcNAc(Ac)3-substituted HEMA), glucose-substituted HEMA (GEMA) and 6-O-vinyladipoyl-D-glucose (6-O-VAG) with vinyl acetate (VAc), were carried out using poly(vinyl alcohol) as an emulsifying agent in the presence of poly[(butylene succinate)-co-(butylene adipate)] [poly(BS-co-BA)]. Copolymerization with GEMA produced a stable emulsion and that with 6-O-VAG also produced a homogeneous emulsion. Their biodegradation tests indicated that PVAc main chain scission was accelerated by copolymerization with vinyl sugars.     

Poly(vinyl acetate)/poly(vinyl alcohol)/montmorillonite nanocomposite microspheres prepared by suspension polymerization and saponification

Poly(vinyl acetate) (PVAc)–poly(vinyl alcohol)–montmorillonite (MMT) nanocomposite microspheres were prepared through suspension polymerization followed by the heterogeneous saponification. The effects of MMT on the polymerization rate and the saponification rate of PVAc were studied. It was found that the rate of polymerization decreased when MMT content was increased. However, the saponification rate of PVAc significantly increased in the presence of nanoclay particles. The XRD measurement illustrated that the clay particles are intercalated in the polymer matrix.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

Xanthates designed for the preparation of N‐Vinyl pyrrolidone‐based linear and star architectures via RAFT polymerization

Novel xanthate RAFT agents, RAFT1‐5, designed for the preparation of a range of novel N‐vinyl pyrrolidone‐based polymeric materials with linear and star architectures via RAFT polymerization are reported. Ethyl pyrrolidone moiety was included in the structures of the xanthates as a part of R (RAFT1‐3) or Z group (RAFT4) to evaluate their effect on the polymerization and to impart homogeneity in the resulting products. The xanthates were designed to fragment to give primary (RAFT1), secondary (RAFT2 and 4), and tertiary radicals (RAFT 3) allowing evaluation of their effect on polymerization. RAFT5 was designed to produce polymeric materials with four‐arm architectures. RAFT1 showed comparable characteristics as conventional radical polymerization. RAFT2 and RAFT4 exhibited living/controlled polymerizations, owing to the combination of stable secondary radical species and incorporation of ethyl pyrrolidone moiety as the R and Z group, respectively. RAFT2 and RAFT5 gave first examples of random copolymers of NVP and VAc with linear and four‐arm star architectures, all exhibiting monomodal distributions and narrow dispersity. The four‐arm PVAc star was used as a macroCTA to synthesize amphiphilic four‐arm star PVAc‐block‐PNVP. The TEM investigation showed the formation of spherical micelles with an average diameter of about 60 nm. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 775–786     

Aspects of Living Radical Polymerization Mediated by Cobalt Porphyrin Complexes

Living radical polymerization (LRP) of methyl acrylate (MA), acrylic acid (AA), and vinyl acetate (VAc) mediated by cobalt(II) porphyrin complexes ((TMP)Co^II·, (TMPS)Co^II·) are reported. The polymeric products with relatively low polydispersity and controlled number average molecular weight (M_n) based on one polymer chain per cobalt complex demonstrate the living characters of the polymerization process. The formation of block copolymers of poly(methyl acrylate)‐b‐poly(vinyl acetate) (PMA‐b‐PVAc) and poly(methyl acrylate)‐b‐poly(vinyl pyrrolidone) (PMA‐b‐PVP) demonstrate another important feature of LRP and extend the application of cobalt porphyrin mediated radical polymerization to a wider array of functionalized monomers. Kinetic studies using ¹H NMR to follow the formation of orGano‐cobalt complexes reveal that two mechanisms, reversible termination (RT) and degenerative transfer (DT), occur during the polymerization process. MA and VAc polymerization mediated by cobalt porphyrin complexes are used to illustrate the properties of these two LRP pathways and evaluate the kinetic and thermodynamic properties for several of the central reactions.     

Synthesis of Poly(Vinyl Alcohol) and/or Poly(Vinyl Acetate) Particles with Spherical Morphology and Core-Shell Structure and its Use in Vascular Embolization

Poly(vinyl alcohol), PVA, is the most frequently used material in embolization of tumors, aneurisms and arteriovenous malformations due to its low toxicity, good biocompatibility and desirable physical properties. It is well known that PVA particles cannot be prepared by direct polymerization of vinyl alcohol. Its synthesis is typically performed by the suspension polymerization of vinyl acetate to produce poly(vinyl acetate), PVAc, followed by the saponification of the PVAc particles. This work shows that, using the suspension polymerization technique, it is possible to obtain spherical particles with a core-shell structure of PVA/PVAc with regular morphology, instead of particles with irregular shapes and sizes, as usually found in many commercial embolization products. Therefore, this work presents the production of PVA/PVAc spherical particles that can be used to occlude blood vessels, eliminating the disadvantages of commercial PVA. In vivo clinical tests with white “New Zealand” rabbits undergoing kidney inflammation reaction have shown that these spherical particles are much more efficient for vascular embolization.