Ag/TiO2中空纳米纤维光催化材料的制备及表征

以棉花纤维为模板制备了银掺杂的TiO₂中空纳米纤维光催化材料, 利用热重分析(TG)、扫描电子显微镜(SEM)、X光电子能谱(XPS)、X射线衍射(XRD)、Zeta电位、紫外-可见光谱(UV-Vis)和傅立叶变换红外光谱(FT-IR)等技术对该材料的形貌、晶体结构、银的状态等特性进行了表征. 以亚甲基蓝(MB)的脱色降解为模型反应, 考察了银掺杂的样品Ag/TiO₂在不同光源下的光催化性能. 结果表明, 所制得的Ag/TiO₂材料保留了棉花纤维的形貌, 且表面带有大量的负电荷|该Ag/TiO₂材料在太阳光条件下的光催化性能显著高于同条件下TiO₂和同材料在紫外光条件下的, 如Ag/TiO₂在太阳光下1.5 h可使MB溶液的脱色降解率在95%以上, 在TiO₂上2.5 h时不足60%, 低于Ag/TiO₂上0.5 h的结果|在紫外光条件下Ag/TiO₂ 3 h时脱色降解率仅为35%. 连续重复使用5次时Ag/TiO₂仍能保证MB溶液的脱色降解率在90%以上|该纤维光催化材料易于离心分离去除、再利用. 因此, 以棉花为模板制备的Ag/TiO₂中空纳米纤维催化材料是一种无能耗、无污染、高活性的绿色环保型光催化材料.     

AgBr/TiO2复合催化剂:双注法制备及其可见光催化性能

以TiO₂为载体,采用双注法合成了AgBr/TiO₂复合光催化剂.利用X射线衍射仪(XRD)、紫外可见分光光度计(UV-Vis)和扫描电子显微镜(SEM)对AgBr/TiO₂的结构、光吸收、形貌进行了表征.研究了AgBr/TiO₂在可见光下对甲基橙和丁基罗丹明B的光催化活性.结果表明,与TiO₂相比,AgBr/TiO₂的光吸收范围拓展到400—600nm波段,并且随着AgBr负载量的增加,AgBr/TiO₂的可见光吸收强度增强;当AgBr与TiO₂的摩尔比为0.25时,AgBr/TiO₂具有最大催化活性;在相同条件下,AgBr/TiO₂对丁基罗丹明B的降解效果优于甲基橙.     

乙酸修饰Ag/TiO2复合光催化剂的制备及协同催化性能

利用光化学还原法制备了Ag/TiO₂,然后通过乙酸浸渍制备了HAc-Ag/TiO₂复合光催化剂.利用X射线衍射（XRD）、透射电子显微镜（TEM）、傅里叶变换红外光谱（FTIR）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）等手段表征了催化剂的性质.以降解水溶液中的甲基橙（MO）为探针反应,考察了催化剂在可见光下的光催化性能.结果表明,乙酸对TiO₂的修饰在TiO₂禁带中产生了"带尾",使TiO₂的禁带宽度发生了显著的缩减;Ag纳米粒子和乙酸共同修饰的HAc-Ag/TiO₂样品具有更窄的禁带宽度和更正的价带顶位置;Ag和乙酸的协同作用使HAc-Ag/TiO₂具有良好的可见光催化活性：可见光照射2 h后,甲基橙在HAc-Ag/TiO₂上的降解率接近100%.     

掺杂WO3的SiO2/TiO2的溶胶热液合成及光催化性能

采用溶胶-热液合成法制备了掺杂WO₃的SiO₂/TiO₂复合光催化剂,用X射线衍射、红外光谱、Zeta电位分析、BET和透射电镜对样品进行了表征,并以甲基橙降解评价了其光催化性能.结果表明:改性后的光催化剂表现出较高的光催化性能,WO₃和SiO₂不仅增加了锐钛矿TiO₂的稳定性,并阻止了TiO₂晶粒的聚集生长.     

在一种新的溶剂体系中通过静电纺丝制备TiO2纳米纤维

以钛酸四丁酯为前驱体, 醋酸纤维素为模板纤维, 丙酮/N,N-二甲基乙酰胺为溶剂, 通过静电纺丝, 水解和450 ℃煅烧制备了直径约为80 nm的锐钛矿型TiO₂纳米纤维. 通过扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)和N₂吸脱附法表征了TiO₂纳米纤维的形貌、直径大小、晶态、比表面积、孔结构及分布. 研究表明该纳米纤维由大小为9.2 nm的颗粒组成, 纤维内含有大量直径为1.7～21 nm的介孔. 它具有与直径为25 nm的商业化Degussa P25相似的高比表面积, 约为50 m²/g. 研究了TiO₂纳米纤维对有机小分子化合物罗丹明B (RhB)和苯酚的光催化降解. 结果表明: 以6 mg/L的RhB和10 mg/L的苯酚水溶液为母液, 以质量分数为0.05%的TiO₂纳米纤维膜为催化剂, 在500 W的紫外灯照射下, 2 h内约90%的RhB和75%的苯酚能被光催化降解.     

高度有序的二氧化钛纳米管阵列的制备及其光催化活性的研究

采用电化学阳极氧化法在钛表面构筑了一种结构有序、微米级的TiO₂纳米管阵列膜层. 考察了制备电压、氧化时间、溶液搅拌等实验参数对TiO₂纳米管阵列形貌和尺寸的影响. 应用SEM和XRD对膜层的形貌和晶型进行了分析和表征, 并通过TiO₂纳米管阵列膜对甲基橙的光催化降解, 研究了TiO₂纳米管阵列膜层结构与光催化活性的关系. 结果表明: 阳极电压和溶液搅拌对制备TiO₂纳米管阵列的结构起到关键的作用. 控制20 V电压制备的TiO₂纳米管阵列膜, 管长达2.6～3.3 μm, 经500 ℃热处理后具有最高的光催化活性, 其光催化性能明显优于一般的TiO₂纳米颗粒膜.     

类蛋结构的可磁分离光催化剂纳米球的制备及催化性能

通过反胶束和静电自组装方法制备了一种类蛋结构的可磁分离光催化剂纳米材料SiO₂@NiFe₂O₄@TiO₂(TSN), 这种光催化剂对甲基橙废水有较好的降解效果, 并显示出了超顺磁性, 通过外加磁场方便地实现催化剂在水中的分离与回收. 该光催化剂纳米球的X射线衍射, TEM和FTIR结果表明, 铁酸镍纳米粒子被包裹在SiO₂内, 形成SiO₂@NiFe₂O₄(SN)纳米球载体, 纳米TiO₂颗粒组装在SN表面, 形成TiO₂光催化壳层. 利用甲基橙的降解考察了光催化剂纳米球的活性, 结果表明, 在NiFe₂O₄和TiO₂之间包覆一层无定形的SiO₂可以显著提高光催化剂纳米球TSN的催化活性.     

模拟太阳光下稀土Gd掺杂TiO2纳米晶的光催化性能研究

以甲基橙的光催化降解为探针反应,采用氙灯模拟自然条件下的太阳光,评价了通过酸催化的溶胶-凝胶法制备的稀土Gd掺杂改性TiO₂纳米晶的光催化活性及对甲基橙水溶液TOC的去除效果.运用XRD和UV-Vis DRS表征技术考察了Gd掺杂对纳米TiO₂的微晶尺寸、晶体结构与光学性能的影响.结果表明,Gd掺杂可以抑制TiO₂由锐钛矿相向金红石相的转变,阻碍TiO₂晶粒增长,使TiO₂的光吸收带边发生蓝移且有利于对可见光的吸收,从而使Gd掺杂TiO₂在模拟太阳光下光催化降解甲基橙的能力得到明显提高,但样品对甲基橙水溶液TOC的去除效果要滞后于其对色度的去除.     

(BiO)2CO3-Bi-TiO2复合纳米纤维制备及其光催化降解抗生素

以静电纺丝制备的TiO₂纳米纤维为基质,葡萄糖为还原剂,在不同的酸碱环境中,采用一步水热法可控合成了异质结型Bi-TiO₂、(BiO)₂CO₃-TiO₂和(BiO)₂CO₃-Bi-TiO₂复合纳米纤维光催化剂。通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和光致发光光谱(PL)等对样品进行表征。以洛美沙星、环丙沙星和诺氟沙星为目标污染物,研究了TiO₂及其复合纳米纤维的光催化降解性能,并探究其降解反应机理。结果表明,(BiO)₂CO₃-Bi-TiO₂光催化活性最高,模拟太阳光照60 min,对诺氟沙星、洛美沙星和环丙沙星的降解率分别达到93.2%、97.5%和100%。     

一步火焰辅助热解法制备Fe掺杂嵌碳TiO2及其光催化性能

以钛酸四丁酯、无水乙醇和无水氯化铁为前驱体,通过一步火焰辅助热解法制备了Fe掺杂嵌碳TiO₂,并研究了样品的光催化活性. 利用扫描电子显微镜及能谱、X射线光电子能谱、X射线粉末衍射和紫外-可见漫反射吸收光谱等对样品的形貌、组分、晶型和光吸收进行了表征,并研究了样品在紫外和可见光下的光催化活性. 结果表明,无需后续热处理可直接得到主要是锐钛矿相TiO₂的样品,Fe³⁺以替位掺杂形式进入TiO₂晶格,随掺杂量增加,样品在可见光区域的吸光度提高,吸收带边红移. Fe掺杂量（摩尔分数）小于0.2%可改善样品的光催化活性,当Fe掺杂量为0.1%时,样品在可见光和紫外-可见光照射下均显示出最高的降解亚甲基蓝速率.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.