大功率GaN基发光二极管等效串联电阻的功率耗散及其对发光效率的影响

由于自加热效应的存在，大功率GaN基发光二极管(LED)的芯片温度有可能高出环境温度很多，实验中，芯片温度超出环境高达147 K.从实验测量的大功率LED电流电压特性曲线中，将p-n结和等效串联电阻上的电压降落分离出来，得到了大功率LED等效串联电阻随芯片温度的变化情况.在输入电功率自加热效应的影响下，大功率GaN基LED等效串联电阻呈现出剧烈的变化，其阻值由低输入功率时的1.2 Ω降低到0.9 Ω,然后再升高到1.9 Ω，等效串联电阻的功率耗散在输入功率中所占的比例也随着输入功率的增加迅速增加，最高时接     

电极结构优化对大功率GaN基发光二极管性能的影响

在台面结构的GaN基发光二极管(LED)里，电流要侧向传输，当尺寸与电流密度加大之后，由于n型GaN层和下限制层的横向电阻不能忽略，造成了横向电流分布不均匀.通过优化电极结构，以减小电流横向传输距离，制作出两种不同电极结构的大功率GaN基倒装LED.通过比较这两种不同电极结构的GaN基倒装大功率LED的电、光性能，发现在350mA正向电流下，插指电极结构的倒装大功率GaN基LED的正向电压为3.35V，比环形插指电极结构的倒装大功率GaN基LED高0.15V.尽管环形插指电极结构GaN基LED的发光面积略小于插指电极结构GaN基LED，但在大电流下，环形插指电极结构倒装GaN基LED的光输出功率比插指电极结构的倒装大功率LED的光输出功率大.并且在大电流下，环形插指电极结构的倒装大功率LED光输出功率饱和速度慢，而插指电极结构的倒装大功率LED光输出功率饱和明显.这说明优化电极结构能提高电流扩展均匀性，减小焦耳热的产生，改善GaN基LED的性能.     

GaN基蓝光LED中光子晶体对提取效率及发光偏振态的影响

为了提高氮化镓基蓝光发光二极管的发光提取效率,在其电流扩展层上生长光子晶体.讨论了光子晶体结构周期、刻蚀深度和占空比参数与提取效率的关系,并采用时域有限差分法进行模拟计算.结果表明在晶格周期为300nm、占空比为60%和刻蚀深度为200nm的条件下,生长光子晶体结构后,氮化镓基蓝光发光二极管的提取效率提升了27.93%.研究了激励源在光子晶体晶格周期内位置变化对提取效率的影响,拟合得到更符合实际物理意义的氮化镓基蓝光发光二极管发光提取效率函数.利用等效折射率理论和法布里-珀罗薄膜干涉模型解释了氮化镓基蓝光发光二极管中TE模和TM模偏振之间提取效率的差异,数值仿真得到最大差异值为1.442倍,从而获得高偏振对比度光源.用该结构参数制备的发光二极管器件应用于液晶显示背光源,可提高液晶显示的能耗效率.     

四端星-网电阻网络的等效变换及其应用

导出了四端星-网(全网)电阻网络的等效变换式,并应用它求出几例特殊复杂电阻网络(非串非并电路)的等效电阻.     

人体模式静电放电对GaN基大功率发光二极管特性的影响

对GaN基大功率蓝光发光二极管(LED)分别施加了-200,-400,-600,-800,-1100和-1500V的反向人体模式静电打击,每次静电打击后,测量样品电学参数和光学参数的变化,研究了静电对LED可靠性的影响,并从理论上分析了相关衰减机理.结果表明,在-200,-400,-600和-800V的打击后,有明显的...     

功率效应对功率LED热阻的影响

分析比较了在不同输入功率条件下1 W GaN基LED样品的热学特性,得出了有效热阻随加载功率的变化规律。基于瞬态热测试方法,讨论了结-环境热阻与输入功率之间的关系。加载电流为100~500 mA的区域随着电功率增加,有效热阻明显降低;当电流增至500 mA以上时,有效热阻减小幅度越来越小;而当加载电流为900~1 650 mA时,结-环境的热阻随着电功率的增加而缓慢升高。随着注入电功率的增加,在不同电流区域同一个样品的热阻变化趋势却是相反的,这个现象归因于串联电阻热耦合随输入功率的变化。该结果对分析功率型LED热特性具有一定参考价值。     

非平衡纯电阻电桥等效电阻的一种特殊计算

用分割电阻法构造出非平衡电阻电桥的特殊串联与并联组合的混联电路后,应用串、并联电路的电流特点和电压特点,巧妙导出了非平衡电阻电桥(非串联又非并联电阻组成的复杂电路)的等效电阻.     

无序光子晶体提高GaN基蓝光发光二极管光提取效率的研究

亚波长尺度光子晶体结构可有效提升发光二极管(LED)的光提取效率(LEE),然而在制造过程中会存在缺陷或无序.利用时域有限差分法对理想方形光子晶体结构进行了优化,在此基础上对三种无序光子晶体结构进行了仿真,研究了光子晶体结构参数的无序变化对GaN基蓝光LED LEE的影响.结果表明,光子晶体空气孔位置和半径的无序变化使优化的80 nm光子晶体LED的LEE下降,而可使非优化的60nm光子晶体LED的LEE增加;当光子晶体空气孔位置和半径的无序变化量从0到士20 nm之间变化时,LEE最大会产生53.8％的浮动;光子晶体刻蚀深度的无序变化对LEE影响较小,一般可以忽略,研究结果为高性能蓝光光子晶体LED的设计制作提供了重要的理论参考.     

固定关断时间控制Buck变换器输出电容等效串联电阻的稳定性分析

通过专用电力电子仿真软件进行电路仿真, 定性分析了固定关断时间(fixed off-time, FOT)控制Buck变换器输出电压相位滞后于电感电流相位的原因及其引发脉冲簇发现象的机理, 探讨了如何调整输出电容等效串联电阻(equivalent series resistance, ESR)的大小来消除这些复杂非线性现象, 并定量给出了FOT控制Buck变换器处于稳定工作状态时的ESR临界值.结果表明, 输出电容ESR对FOT控制Buck变换器工作状态的影响较大, 当ESR小于临界值时, 输出电压相位滞后于电感电流相位, 发生脉冲簇发现象;而当ESR大于临界值时, 输出电压与电感电流的变化保持同步, 脉冲簇发现象消失.通过描述函数法建立了参考电压至输出电压的传递函数, 由Routh-Hurwitz判据说明了ESR临界值是FOT控制Buck变换器的失稳条件.     

基于缺陷光子晶体结构的GaN基发光二极管光提取效率的有关研究

现有的研究表明,利用光子晶体可以有效提高发光二极管的光提取效率.由于在制造时光子晶体中可能会存在缺陷和错位,本文基于时域有限差分法对光子晶体中的缺陷和错位对发光二极管发光效率的影响进行了研究.数值仿真结果表明,光子晶体中少量缺陷或者微小错位并不会降低发光二极管的光提取效率,其中某些缺陷反而能增强光子晶体发光二极管的光提取效率.本文对其物理机理给出了详细的理论分析,并设计了一种具有缺陷的光于晶体,在未刻蚀到有源层(离有源层20 nm)的情况下,其光提取效率达到了完美光子晶体的1.6倍.通过对这种缺陷光子晶体的空间频谱分析可知,可以通过设计具有特殊空间频谱分布的光子晶体来提高发光二极管的发光效率,这对设计高光提取效率的光子晶体结构和制造高效率的发光二极管有指导意义.     

High power efficiency in single layer blue phosphorescent organic light-emitting diodes

High efficiency single layer blue phosphorescent organic light-emitting diodes (PHOLEDs) without any charge transport layer were developed. A mixed host of spirobifluorene based phosphine oxide (SPPO13) and 1, 1-bis[(di-4-tolylamino)phenyl]cyclohexane (TAPC) was used as the host in the emitting layer. A high maximum external quantum efficiency of 15.8% and a quantum efficiency of 8.6% at 1000 cd/m² were achieved in the single-layer blue PHOLEDs without any charge transport layer. The maximum power efficiency and power efficiency at 1000 cd/m² were 31.4 and 16.9 lm/W, respectively.     

Ligand effect on the performance of organic light-emitting diodes based on europium complexes

A series of europium complexes were synthesized and their electroluminescent (EL) characteristics were studied. It was found by comparison that the different substituted groups, such as methyl, chlorine, and nitryl, on ligand 1,10-phenanthroline affect significantly the EL performance of devices based on these complexes. The more methyl-substituted groups on ligand 1,10-phenanthroline led to higher device efficiency. A chlorine-substituted group showed the approximate EL performance as two methyl-substituted groups, whereas a nitryl substituent reduced significantly the EL luminous efficiency. However, β-diketonate ligand TTA and DBM exhibited similar EL performance. The improved EL luminous efficiency by proper substituted groups on the 1,10-phenanthroline was attributed to the reduction of the energy loss caused by light hydrogen atom vibration, as well as concentration quenching caused by intermolecular interaction, and the match of energy level between the ligand and Eu³⁺.     

GaN/In_xGa_(1-x)N型最后一个量子势垒对发光二极管内量子效率的影响

GaN/In_xGa_(1-x)N型最后一个量子势垒结构能有效提高发光二极管(LED)器件内量子效率,缓解LED效率随输入电流增大而衰减的问题.本文综述了该结构及其结构变化——In组分梯度递增以及渐变、GaN/In_xGa_(1-x)N界面极化率改变等对改善LED器件性能的影响及优势,归纳总结了不同结构的GaN/In_xGa_(1-x)N型最后一个量子垒的工作机理,阐明极化反转是该结构提高LED性能的根本原因.在综述该结构发展的基础之上,通过APSYS仿真计算,进一步探索和深入分析了该结构中In_xGa_(1-x)N层的In组分及其厚度变化对LED内量子效率的影响.结果表明:In组分的增加有助于在GaN/In_xGa_(1-x)N界面产生更多的极化负电荷,增加GaN以及电子阻挡层处导带势垒高度,减少电子泄漏,从而提高LED的内量子效率;但GaN/In_xGa_(1-x)N型最后一个量子势垒中In_xGa_(1-x)N及GaN层厚度的变化由于会同时引起势垒高度和隧穿效应的改变,因而In_xGa_(1-x)N和GaN层的厚度存在一个最佳比值以实现最大化的减小漏电子,提高内量子效率.     

白光有机电致发光器件的载流子传输与复合特性

基于一种将具有电荷传输性的双极性主体材料与蓝、黄光客体材料共蒸的单层结构的同质结结构,制备了色温可调的白光有机电致发光器件(OLED)。由于不存在激子阻挡层,单层结构容易发生漏电流现象,致使OLED器件具有较高的工作电压和较低的电流/功率效率。在空穴/电子传输层进行p/n型掺杂的同质结结构则大大改善了器件性能。研究表明: 该种器件结构获得了相对较低的起压5.6 V,较高的电流效率2.64 cd/A和低效率滚降,其色坐标则随着亮度的增加沿着普朗克轨迹变化,产生类似于太阳光的发光特性。另外,对主体材料和共蒸层的电荷载流子的传输特性和复合机制也进行了一系列分析研究。     

White organic light-emitting diodes based on electroplex from polyvinyl carbazole and carbazole oligomers blends

White organic light-emitting diodes with a blue emitting material fluorene-centred ethylene-liked carbazole oligomer (Cz6F) doped into polyvinyl carbazole (PVK) as the single light-emitting layer are reported. The optical properties of Cz6F, PVK, and PVK:Cz6F blends are studied. Single and double layer devices are fabricated by using PVK: Cz6F blends, and the device with the configuration of indium tin oxide (ITO)/PVK:Cz6F/ tris(8-hydroxyquinolinate)aluminium (Alq₃)/LiF/Al exhibits white light emission with Commission Internationale de l'éclairage chromaticity coordinates of (0.30, 0.33) and a brightness of 402~cd/m². The investigation reveals that the white light is composed of a blue--green emission originating from the excimer of Cz6F molecules and a red emission from an electroplex from the PVK:Cz6F blend films.     

Determination of the series resistance under the Schottky contacts of AlGaN/AlN/GaN Schottky barrier diodes

Rectangular AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) were fabricated, and the gate and the source of the HFETs consisted of AlGaN/AlN/GaN Schottky barrier diodes (SBDs). Based on the measured forward current-voltage and the capacitance-voltage characteristics of the AlGaN/AlN/GaN SBDs, the series resistance under the Schottky contacts (R_S) was calculated using the method of power consumption, which has been proved to be valid. Finally, the method of power consumption for calculating R_S was successfully used to study the two-dimensional electron gas electron mobility for a series of circular AlGaN/AlN/GaN SBDs. It is shown that the series resistance under the Schottky contacts cannot be neglected and is important for analysing and characterizing the AlGaN/AlN/GaN SBDs and the AlGaN/AlN/GaN HFETs.     

渐变型量子阱垒层厚度对GaN基双波长发光二极管发光特性调控的研究

采用软件理论分析的方法对渐变型量子阱垒层厚度的InGaN双波长发光二极(LED)的载流子浓度分布、 能带结构、自发发射谱、内量子效率、发光功率及溢出电子流等进行研究.分析结果表明, 增大量子阱垒层厚度会影响空穴在各量子阱的注入情况, 对双波长LED各量子阱中空穴浓度分布的 均衡性及双波长发光光谱的调控起到一定作用,但会导致内量子效率严重下降; 而当以特定的方式从n电极到p电极方向递减渐变量子阱垒层厚度时, 活性层量子阱的溢出电子流 得到有效的控制, 双发光峰强度达到基本一致, 同时芯片的内量子效率下降得到了有效控制, 且具备大驱动电流下较好的发光特性.     

Theoretical and experimental analysis of the effects of the series resistance on luminous efficacy in GaN-based light emitting diodes

In this paper, a new equivalent circuit model of GaN-based light emitting diodes （LEDs） is established. The impact of the series resistance to luminous efficacy is simulated using the MATLAB software. GaN-based LEDs with different n- contact electrode materials （LEDs with Ni/Au and LEDs with Cr/Au） are fabricated. By comparing and analyzing the results of performances, we concluded that both the series resistance and the carrier loss could affect the luminous efficacy severely. LEDs with lower series resistance have higher luminous efficacy and its efficiency droop is alleviated simultaneously. To improve luminous efficacy, the fabrication process should be optimized for lower series resistance.     

The effect of alkaline metal chlorides on the properties of organic light-emitting diodes

The multilayer organic light-emitting diodes (OLEDs) have been fabricated with a thin alkaline metal chloride layer inserted inside an electron transport layer (ETL), tris (8-hydroxyquinoline) aluminum (Alq₃). The alkaline metal chloride layer was inserted inside 60 nm Alq₃ at d=0, 10, 20 and 30 nm positions (d is the distance of the interlayer away from the Al cathode). The devices, with alkaline metal chlorides inserted at the Alq₃/Al interface, showed electron injection and electroluminescence (EL) intensity improvements. When the alkaline metal chlorides were inserted inside the Alq₃ layer at 10, 20 or 30 nm position apart from the Al cathode, both EL intensity and efficiency were enhanced for the devices with a thin potassium chloride (KCl) or rubidium chloride (RbCl) layer. On the contrary, the improvements were not observed for the OLEDs with a thin sodium chloride (NaCl) layer. A proposed insulator buffer layer model is employed to explain these characteristics of the devices.