首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007  相似文献   

2.
The crystallization behavior of the blends of isotactic polypropylene (iPP) and poly(ethylene-co-octene) (PEOc) under quiescent condition and shear flow were studied by differential scanning calorimetry (DSC) and rheology, respectively. The DSC curves of the iPP phase in the blends showed similar crystallization exothermic peaks to that of pure iPP itself, indicating that the addition of PEOc up to a percentage of 30 in weight almost had no influence on the crystallization behavior of iPP at quiescent condition. The rheological results of isothermal flow-induced crystallization (FIC) of iPP in the blends showed that the crystallization kinetics of iPP was enhanced with the increase of shear rate, similar to that of pure iPP, but the presence of PEOc enhanced the effect of shear on the crystallization kinetics of iPP significantly in the cases of shear rates larger than 0.2 s−1, which was due to that PEOc played an important role to promote the nucleation of iPP. The rheological results also implied that the characteristic relaxation times of blends were longer than that of pure iPP during the FIC process, indicating a different relaxation mechanism which might be related to the occurrence of interface relaxation and chain relaxation of the PEOc phase in the blends.  相似文献   

3.
Morphology development during isothermal crystallization in equal molecular weight isotactic polypropylene (iPP), syndiotactic polypropylene (sPP), and iPP/sPP blends was studied with time‐resolved simultaneous small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) with synchrotron radiation. The sPP melting point is 15–20 °C below that of the iPP component, and sPP multiple melting is not affected by blending for 50–100 wt % sPP compositions. SAXS and WAXD (at 115 and 137.5 °C) show that sPP crystallizes more slowly than iPP. The sPP long spacing is larger than that of iPP at both crystallization temperatures, exhibits a broader distribution, and changes to a greater extent during crystallization. Differential scanning calorimetry (DSC) cooling and SAXS/WAXD measurements show iPP crystallizing first and nearly to completion before sPP in a 50:50 iPP/sPP blend. At 115 °C, iPP crystals nucleate sPP in a 50:50 blend and modify the sPP lamellar spacing. The nucleation does not overcome the large difference in the iPP and sPP rates at 137.5 °C. Before sPP crystallization in a 50:50 blend (115 °C), the iPP long spacing is not affected by molten sPP. The iPP long spacing is slightly expanded by molten sPP, and the WAXD induction time is delayed at 137.5 °C. The observed iPP long spacing in the presence of molten sPP is consistent with previously reported results for iPP/atactic polypropylene (aPP) blends of similar molecular weight. Quantitative differences between the two types of blends are consistent with previously reported thermodynamic rankings. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1876–1888, 2001  相似文献   

4.
The macromorphology of isotactic/atactic (iPP/aPP) and isotactic/syndiotactic (iPP/sPP) polypropylene mixtures is examined by optical microscopy. The spherulitic macrostructure of equimolecular weight [weight‐average molecular weight (Mw) = 200k] iPP/aPP blends is volume‐filling to very high aPP concentrations when the crystallization temperature is 130 °C. Similar spherulitic macrostructures (spherulite size and volume‐filling nature) are observed for iPP homopolymer and a 50/50 iPP/aPP blend at low crystallization temperatures (115–135 °C). At higher crystallization temperatures (140–145 °C), a equimolecular weight (Mw = 200k) 50/50 iPP/aPP blend exhibits nodular texture that blurs the spherulitic boundaries. Double temperature jump experiments show that the nodular texture is due to melt phase separation that develops prior to crystallization. The upper critical solution temperature (UCST) of a 50/50 iPP/aPP blend (Mw = 200k) lies below 155 °C, and the blend is miscible at conventional melt processing temperatures. The UCST behavior is controlled by the blend molecular weight and aPP microstructure. aPP microstructures containing increased isospecific sequencing (although still noncrystalline) exhibit a reduced tendency for phase separation in 50/50 mixtures (Mw = 200k) and the absence of nodular texture at low undercoolings (140–145 °C). Equimolecular weight (Mw = 200k) 50/50 iPP/sPP mixtures exhibit phase‐separated texture at all crystallization temperatures. The size scale of the phase‐separated texture decreases with decreasing crystallization temperature because of a competition between crystallization and phase separation from a melt initially well mixed from the initial solution blending process. Extended melt annealing experiments show that the 50/50 iPP/sPP mixture (Mw = 200k) is immiscible in the melt at conventional melt processing temperatures. The iPP/sPP pair shows a much stronger tendency for phase separation than the iPP/aPP polymer pair. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1947–1964, 2000  相似文献   

5.
Morphology development during isothermal crystallization in equal molecular weight isotactic polypropylene (iPP) and atactic polypropylene (aPP) blends was studied with time‐resolved simultaneous small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray scattering methods with synchrotron radiation. The final long period obtained after crystallization at 115 °C was nearly independent of blend composition up to 50 wt % aPP but showed an increase in the 80 wt % aPP blend. At a high crystallization temperature (137.5 °C), the increase in the final long period with aPP content was significant, and the evolution of iPP crystallinity was also affected. However, at low crystallization temperatures, the additive decrease of the crystallinity and the constant melting point with increasing aPP content suggest that the crystallizability and crystal morphology of iPP is not a strong function of aPP. The iPP/aPP blends showed a strong low‐angle SAXS upturn as a function of composition, which suggests the segregation of aPP on size scales larger than the lamellar spacing. A detailed analysis of the SAXS patterns indicates that aPP disrupts the ordering within the lamellar stacking. The results are generally consistent with predominantly interfibrillar incorporation of the aPP diluent within the microstructure, with only modest interlamellar incorporation dependent on the crystallization temperature. The findings can be attributed to the partial miscibility/mixing of the aPP and iPP components in the blend before crystallization, depending on the crystallization undercooling. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2580–2590, 2000  相似文献   

6.
The compatibilization of incompatible polypropylene (PP)/poly(ethylene oxide) (PEO) blends was studied. The experimental results showed that the graft copolymer [(PP-MA)-g-PEO] of maleated PP(PP-MA) and mono-hydroxyl PEO (PEO-OH) was a good compatibilizer for the PP/PEO blends in which PP-MA also had some compatibilization. The crystallization of the blends was affected by the compatibility between PP and PEO. The interfacial behavior of the compatibilizers had an important effect on crystallization behavior of the PP/PEO blends. PEO showed fractionated crystallization in the PP/PEO blends. This behavior was studied from the view point of the theory of fractionated crystallization. © 1994 John Wiley & Sons, Inc.  相似文献   

7.
Non-isothermal crystallization and crystalline structure Of PP/POE blends   总被引:4,自引:0,他引:4  
Polypropylene (PP) /ethylene-octene copolymer (POE) blends with different content of POE were prepared by mixing chamber of a Haake torque rheometer. The crystallization behaviors and crystal structure of PP/POE blends were systematically investigated by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and polarized optical microscopy (POM). The results showed that PP spherulites became defective and the crystallization behavior was influenced intensely with the introduction of POE. At the low content of POE, the addition of POE decreases the apparent incubation period (Δt i) and the apparent total crystallization period (Δt c) of PP in blends due to the heterogeneous nucleation of POE, and small amount of β-form PP crystals form because of the existence of POE. However, at high content of POE, the addition of POE decreases the mobility of PP segments due to their strong intermolecular interaction and chain entanglements, resulting in retarding the crystallization of PP, decreasing in the amount of β-form PP crystals, and increasing in Δt i and Δt c of PP in blends.  相似文献   

8.
于建 《高分子科学》2011,29(3):308-317
An aryl dicarboxylic acid amide compound TMB-5 is an efficientβ-form nucleating agent for isotactic polypropylene(iPP).Because of the solubility of TMB-5,superstructure and morphology of iPP crystals changed with melting conditions.Effects of final heating temperature(T_f)on heterogeneous nucleation of iPP/TMB-5 were investigated.It was discovered that the crystallization temperature increased with decreasing T_f value.The optical microscopic images indicated that when TMB-5 partially dissolved in iPP melt,the remaining(non-dissolved)TMB-5 facilitated the recrystallization of dissolved nucleating agent from the melt,which promoted crystallization.Complete solubility of nucleating agent caused the decreasing efficiency.TMB-5 recrystallized in the form of tiny needles,whose aggregates induced dendritic iPP crystals.  相似文献   

9.
马桂秋 《高分子科学》2012,30(3):423-435
The surface of polypropylene(iPP) is modified with glow discharge plasma of Ar,so that the modified surfaces of iPP films are obtained.The studies of scanning electron microscopy(SEM) show the surface etching pattern of iPP films. The chemical structures of iPP films are confirmed by X-ray photoelectron spectroscopy(XPS) and Fourier transform infrared(FTIR) spectroscopy.The wetting properties of modified surfaces of iPP films are characterized by contact angle, and the free energy of surfaces is calculated.The free radical of modification surfaces of iPP is measured by chemical method.The surfaces of iPP are achieved with Ar plasma treatment followed by grafting copolymerization with styrene(St) in St.The grafting polymer of St onto iPP is characterized by FTIR.The grafting rate is dependent on plasma exposure time and discharge voltage.The studies show that homopolymerization of St is undergone at the same time during the grafting-copolymerization of St onto iPP.  相似文献   

10.
Temperature‐modulated differential scanning calorimetry (TMDSC) and broadband dielectric spectroscopy (BDS) were employed to study the glass transition, size of the cooperative rearranging regions (CRRs), crystallization kinetics, and dielectric relaxation response of nanocomposites constituted by chain‐extended poly(L‐lactide) (PLLA) and carboxylated carbon nanotubes (f‐CNTs). The CRR size and the number of relaxing structural units decreased in the presence of crystals during isothermal crystallization. All samples displayed both a primary (α) and secondary (β) relaxation in BDS spectra. The relaxation dynamics of PLLA chains was barely affected by the presence of the f‐CNT. Constrained polymer chains and thickness of interphase (t i) were measured using dielectric spectra in tan δ representation. t i values were found to be 46 and 24 nm for sample containing 0.2 and 0.5% weight fraction of f‐CNT, respectively. All samples underwent partial crystallization (with roughly 30% of final crystalline fraction) some 15 or 20° above their glass‐transition temperature (T g). Crystallization leads to a fragile‐to‐strong transition in the temperature dependence of the cooperative α relaxation and to the increased visibility of a Maxwell–Wagner–Sillars (MWS) interfacial relaxation, which appears to be present in all samples. The heterogeneity of the polymeric samples was quantified in terms of a new parameter, the heterogeneity index (H). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 222–233  相似文献   

11.
The isothermal melt crystallization and the corresponding segmental dynamics, of a high molecular weight poly(ethylene oxide) (PEO) confined by Li7La3Zr2O12 (LLZO) particles in solid electrolyte composites, were monitored by differential scanning calorimetry (DSC) and dielectric relaxation spectroscopy (DRS), respectively. Our results show that the overall crystallinity is positively correlated with the surface area of LLZO particles. The primary and secondary crystallization processes are identified by a modified Avrami equation, while two dynamic modes, the α relaxation and α′ relaxation, were in the DRS measurements. The results reveal an unambiguous correlation between the primary crystallization and the α relaxation, while a correlation between the second crystallization and the α′ relaxation concurrently exist in the electrolyte composites. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 466–477  相似文献   

12.
13.
Highly exfoliated isotactic‐polypropylene/alkyl‐imidazolium modified montmorillonite (PP/IMMT) nanocomposites have been prepared via in situ intercalative polymerization. TEM and XRD results indicated that the obtained composites were highly exfoliated PP/IMMT nanocomposites and the average thickness of IMMT in PP matrix was less than 10 nm, and the distance between adjacent IMMT particles was in the range of 20–200 nm. The isothermal crystallization kinetics of highly exfoliated PP/IMMT nanocomposites were investigated by using differential scanning calorimeter(DSC) and polarized optical microscope (POM). The crystallization half‐time t1/2, crystallization peak time tmax, and the Avrami crystallization rate constant Kn showed that the nanosilicate layers accelerate the overall crystallization rate greatly due to the nucleation effect, and the crystallization rate was increased with the increase in MMT content. Meanwhile, the crystallinity of PP in nanocomposites decreased with the increase in clay content which indicated the PP chains were confined by the nanosilicate layers during the crystallization process. Although the well‐dispersed silicate layers did not have much influence on spherulites growth rate, the nucleation rate and the nuclei density increased significantly. Accordingly, the spherulite size decreased with the increase in MMT content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2215–2225, 2009  相似文献   

14.
The crystallization and melting behavior of a series of poly(glycerol adipate) (PGA) based graft copolymers with either poly(ε‐caprolactone) (PCL), poly(ethylene oxide) (PEO), or PCL‐b‐PEO diblock copolymer side chains (i.e., PGA‐g‐PCL, PGA‐g‐PEO, and PGA‐g‐(PCL‐b‐PEO)) was studied using polarized light optical microscopy (POM), differential scanning calorimetry (DSC), small‐angle X‐ray scattering (SAXS), and wide‐angle X‐ray diffraction (WAXD). These results were compared with the behavior of the corresponding linear analogs (PEO, PCL, and PCL‐b‐PEO). POM revealed that spherulitic morphology was retained after grafting. However, spherulite radius as well as radial growth rate was significantly smaller in the graft copolymers. Evaluation of isothermal crystallization kinetics by means of the Avrami theory revealed that the nucleation density was much higher in the graft copolymers. The DSC results indicated that the degree of crystallinity decreased strongly upon grafting while the melting temperatures of PGA‐g‐PCL and PGA‐g‐PEO were found to be close to the values of neat PCL and PEO, respectively. This was attributed to the absence of specific thermodynamic interactions, and, additionally, to lamella thicknesses being similar to those of the homopolymers. The latter point was confirmed by SAXS measurements. In case of PCL‐b‐PEO diblock copolymers and PGA‐g‐(PCL‐b‐PEO) graft copolymers, the crystallization behavior and thus the resulting lamellar morphology is more complex, and a suitable model was developed based on a combination of DSC, WAXD, and SAXS data. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1581–1591  相似文献   

15.
蒋世春 《高分子科学》2017,35(5):672-680
The crystalline structures and crystallization behaviors of iPP containing β nucleation agent TMB-5 (iPP/TMB-5) were investigated by synchrotron radiation wide angel X-ray diffraction (SR-WAXD), differential scanning calorimeter (DSC) and polarized light microscope (PLM). It was found that α-crystallization lagged behind β-crystallization at normal temperatures, but the discrepancy reduced with increasing temperature. TMB-5 could not induce β-iPP when the nucleation agent is wrapped up with α-crystal that crystallized at high temperatures. The polymorphic composition of iPP/TMB-5 was susceptible to the introductory moment of shear. New crystallization process of β-nucleated iPP was proposed to understand the experimental phenomena which could not be explained by those reported in the literature. It was supposed that polymer crystallization initiated from mesophase, and the formations of iPP crystals involved the organization of helical conformation ordering within mesophase. It was proposed that the iPP melt contained mesophases with stereocomplex-type ordering of right-handed and left-handed helical chains which could be disturbed by shear or TMB-5, leading to different polymorphic structures.  相似文献   

16.
The crystallization kinetics of Cu55Zr45 (at%) glassy alloy is studied under isothermal condition using differential scanning calorimetry (DSC). The plot of correlation between the crystallized volume fraction α and annealing time t shows a sigmoid-type curve, which is steeper with higher annealing temperature. Furthermore, in isothermal crystallization condition, local activation energy Eα values, determined using the Arrhenius equation, range from 181.1 to 187.8 kJ/mol, which is nearly a constant. The local Avrami exponent n(α) values, obtained by the Johnson-Mehl-Avrami equation, which range from 2.2 to 4.0 at different annealing temeperatures, which indicates that the crystallization mechanism is diffusion-controlled transformation. Moreover, n(α) becomes greater with increasing annealing temperature, which indicates that annealing temperature can affect nucleation rate and growth type.  相似文献   

17.
The crystals of N, N′-dicyclohexyl-2,6-naphthalenedicarboxamide (DC26NDCA) and N,N′-dicyclohexyl-1,4-naphthalenedicarboxamide (DC14NDCA) were selected as nucleating agents to induce the crystallization of isotactic polypropylene (i-PP). The influence of the crystal structures of the nucleating agents on the crystallization behaviors and morphologies was studied by means of differential scanning calorimeter, wide-angle X-ray diffraction, polarized light microscopy, and atomic force microscopy (AFM). The results show that DC26NDCA is a selective β-nucleating agent for the i-PP crystallization, while DC14NDCA only has a very weak α-nucleating effect for the i-PP crystallization. The dynamic growth processes reveal that i-PP crystals grow with different crystallization behaviors in the presence of the nucleating agents. The i-PP lamellar structures on the crystal surfaces of the nucleating agents were observed by AFM in details, which suggested that the nucleating agents induced the epitaxial growth of the i-PP lamellae.  相似文献   

18.
The effect of aging on the fractional crystallization of the poly(ethylene oxide) (PEO) component in the PEO/poly(3‐hydroxybutyrate) (PHB) blend has been investigated. The partial miscibility of the PEO/PHB blends with high PEO molecular weight (Mv = 2.0 × 105 g/mol) was confirmed by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis. The fractional crystallization behavior of the PEO component in the PEO/PHB blends with low PEO content (not more than 30 wt% of PEO), before and after aging under vacuum at 25 °C for 6 months, were compared by DSC, fourier transform infrared microscopic spectroscopy, small angle X‐ray diffraction, and scanning electron microscopy. It was confirmed that nearly all the PEO components remain trapped within interlamellar regions of PHB for the PEO/PHB blends before aging. Under this condition, the crystallization of PEO is basically induced by much less active heterogeneities or homogeneous nucleation at high supercoolings. While, after the same PEO/PHB samples were stored at 25 °C in vacuum for 6 months, a part of the PEO component was expelled from the interlamellar region of PHB. Under this condition, the expelled PEO forms many separate domains with bigger size and crystallizes at low supercoolings by active heterogeneous nucleation, whereas the crystallization of PEO in the interlamellar region is still mainly induced by less active heterogeneities or homogeneous nucleation at extreme supercoolings. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2665–2676, 2005  相似文献   

19.
The crystallization behaviors and morphology of asymmetric crystalline–crystalline diblock copolymers poly(ethylene oxide‐lactide) (PEO‐b‐PLLA) were investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and microscopic techniques (polarized optical microscopy (POM) and atomic force microscopy (AFM)). Both blocks of PEO5b‐PLLA16 can be crystallized, which was confirmed by WAXD, while PEO block in PEO5b‐PLLA30 is difficult to crystallize because of the confinement induced by the high glass transition temperature and crystallization of PLLA block with the microphase separation of the block copolymer. Comparing with the crystallization and morphology of PLLA homopolymer and differences between the two copolymers, we studied the influence of PEO block and microphase separation on the crystallization and morphology of PLLA block. The boundary temperature (Tb) was observed, which distinguishes the crystallization into high‐ and low‐temperature ranges, the growth rate and morphology were quite different between the ranges. Crystalline morphologies including banded spherulite, dendritic crystal, and dense branching in PEO5b‐PLLA16 copolymer were formed. The typical morphology of dendritic crystals including two different sectors were observed in PEO5b‐PLLA30 copolymer, which can be explained by secondary nucleation, chain growth direction, and phase separation between the two blocks during the crystallization process. Lozenge‐shaped crystals of PLLA with screw dislocation were also observed employing AFM, but the crystalline morphology of PEO block was not observed using microscopy techniques because of its small size. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1400–1411, 2008  相似文献   

20.
The impact propylene copolymer(IPC)and isotactic polypropylene(iPP)were separately selected to prepare laminates with high density polyethylene(HDPE)by hot press.The peel forces of IPC/HDPE and i’PP/HDPE laminates were examined,and it was found that the welded joint strength in IPC/HDPE laminate was dramatically higher than that of iPP/HDPE laminate.According to the special microstructure of IPC,the co-crystallization of the ethylene segments in ethylene-propylene block copolymer(EbP)component of IPC and the PE chain in HDPE was proposed to explain the high-strength welding.The DSC results indicated that there indeed existed some interaction between IPC and HDPE,and the crystallizable PE component in IPC could affect the crystallization of HDPE.The scanning electron microscope(SEM) observations of IPC/HDPE blends demonstrated that HDPE tended to stay with the PE-rich EbP chains to form the dispersed phase,indicating the good miscibility between HDPE and EbP components of IPC.According to the above results,the effect of co-crystallization of the PE components of the IPC and HDPE on the high weld strength of IPC/HDPE laminate was confirmed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号