Monitoring of the <Superscript>14</Superscript>C concentration in the stack air of the nuclear power plant VVER Jaslovske Bohunice

¹⁴C releases in the stack air of the NPPs V1 and V2, Jaslovske Bohunice was determined during the year 2004–2010. Radioactivity concentration of ¹⁴C in the stack air was determined in the forms of inorganic ¹⁴CO₂ and ¹⁴C _n H _m . The annual average activity concentration in the stacks air samples varies between 12 and 121 Bq m⁻³. NPP V1, starting with 45 Bq m⁻³ in 2005 is decreasing due to the shutting down of the reactors (the first reactor was shut down in December 2006 and the second reactor in December 2008). The average value of radioactivity concentration for power unit V2 was 32 Bq m⁻³ in 2004 and reached the value of 102 Bq m⁻³ in the first-quarter of the 2010. The average normalized yearly discharge rates were between 0.39 and 0.64 TBq GW_e⁻¹ year⁻¹ (2005–2008), NPP V1 and 0.19–0.61 TBq GW_e⁻¹ year⁻¹ (2004–first-quarter 2010) for NPP V2, Jaslovske Bohunice. Most of the discharged ¹⁴C is in a hydrocarbon form, (95% for Jaslovske Bohunice NPP V2), but the CO₂ fraction may reach 37% in the air stack for Jaslovske Bohunice V1.     

<Superscript>63</Superscript>Ni schottky barrier nuclear battery of 4H-SiC

The design, fabrication, and testing of a 4H-SiC Schottky betavoltaic nuclear battery based on MEMS fabrication technology are presented in this paper. It uses a Schottky diode with an active area of 3.14 mm² to collect the charge from a 4 mCi/cm^{2 63}Ni source. Some of the critical steps in process integration for fabricating silicon carbide-based Schottky diode were addressed. A prototype of this battery was fabricated and tested under the illumination of the ⁶³Ni source with an activity of 0.12 mCi. An open circuit voltage (V _OC) of 0.27 V and a short circuit current density (J _SC) of 25.57 nA/cm² are measured. The maximum output power density (P _max) of 4.08 nW/cm² and power conversion efficiency (η) of 1.01% is obtained. The performance of this battery is expected to be significantly improved by using larger activity and optimizing the design and processing technology of the battery. By achieving comparable performance with previously constructed p–n or p–i–n junction energy conversion structures, the Schottky barrier diode proves to be a feasible approach to achieve practical betavoltaics.     

Production of <Superscript>122</Superscript>Sb for the study of environmental pollution

This article presents, ¹²²Sb (T _1/2 = 2.723 days, I _β- = 97.59%) was produced via the ^natSn(p,xn) nuclear process at the AMIRS (Cyclone-30, IBA, Belgium). The electrodeposition experiments were carried out by potassium stannate trihydrate (K₂Sn(OH)₆) and potassium hydroxide. The optimum conditions of the electrodeposition of tin were as follows: 40 g/L ^natSn, 20 g/L KOH, 115 g/L K₂Sn(OH)₆, DC current density of 5 A/dm² with a bath temperature of 75 °C. The electroplated Tin-target was irradiated with 26.5 MeV protons at current of 180 μA for 20 min. Solvent extraction of no-carrier-added ¹²²Sb from irradiated Tin-natural target hydrochloric solution was investigated using di-n-butyl ether (C₈H₁₈O). Yields of about 3.61 MBq/μAh were experimentally obtained.     

Preparation of <Superscript>99m</Superscript>Tc-PQQ and preliminary biological evaluation for the NMDA receptor

Pyrroloquinoline quinone (PQQ), an essential nutrient, antioxidant, redox modulator and nerve growth factor found in a class of enzymes called quinoproteins, was labeled with ^99mTc by using stannous fluoride (SnF₂) method. Radiolabeling qualification, quality control and characterization of ^99mTc-PQQ and its biodistribution studies in mice were performed and discussed. Effects of pH values, temperature, time and reducing agents concentration on the radiolabeling yield were investigated. The quality control procedure of ^99mTc-PQQ was determined by thin layer chromatography (TLC), radio high-performance liquid chromatography (RHPLC) and paper electrophoresis methods. The average radiolabeling yield was 94 ± 1% under optimum conditions of 0.99 mg of PQQ, 30 μg of SnF₂, 0.5 mg of ethylenediaminetetraacetic acid disodium salt (EDTA-2Na) and 18.5 MBq of Na^99mTcO₄ at pH 6 and 25 °C with a response volume of 1 ± 0.1 mL. ^99mTc-PQQ was stable and anionic. Lipid–water partition coefficient of ^99mTc-PQQ was −1.49 ± 0.16. The pharmacokinetics parameters of ^99mTc-PQQ were t _1/2α = 18.16 min, t _1/2β = 100.45 min, K ₁₂ = 0.013 min⁻¹, K ₂₁ = 0.017 min⁻¹, K _e = 0.016 min⁻¹, AUC (area under the curve) = 1040.78 ID% g⁻¹ min and CL (plasma clearance) = 0.096 mL min⁻¹. The dual-exponential equation was Y = 10.88e^−0.038t  + 5.21e^−0.0069t . The biodistribution of ^99mTc-PQQ was studied in ICR (Institute for Cancer Research 7701 Burhelme Are., Fox Chase, Philadelphia, PA 1911 USA) mice. In vitro autoradiographic studies clearly showed that the ^99mTc-PQQ radioactivity accumulated predominantly in the hippocampus and cortex, which had a high density of N-methyl-d-aspartate Receptor (NMDAR). The enrichment can be blocked by NMDAR redox modulatory site antagonists-ebselen (EB) and ^99mTc-PQQ is therefore a promising candidate for the molecular imaging of NMDAR. To date, however, there have been no studies characterizing ^99mTc-PQQ.     

Stabilization of <Emphasis Type="Italic">Luciola mingrelica</Emphasis> firefly luciferase by genetic engineering methods

The results of Luciola mingrelica firefly luciferase stabilization by genetic engineering methods are reviewed. The Cys62, Cys146, and Cys164 to Ser mutant enzymes with an enhanced thermostability and lower sensitivity to dithiothreitol were obtained by site-directed mutagenesis. The double mutant G216N, A217L was obtained, which displayed a higher thermostability and resistance to DMSO in comparison with WT luciferase. Random mutagenesis of the gene region encoding residues 1–225 and subsequent screening of the mutants resulted in the production of the mutant MT8 with a higher thermostability, as well as mutants MT3 and MT4 with higher resistance to dimethyl sulfoxide. The mutant 4TS was obtained by the method of directed evolution of the gene site encoding residues 130–390, which was shown to contain eight replacements after four cycles of mutagenesis and had two-fold higher specific activity, eight-fold lower K _m value for ATP, and stability at 42°C, which was 65-fold higher that of WT luciferase. The stabilization mechanism of this mutant is discussed.     

Cage Structure Formation of Singly Doped Aluminum Cluster Cations Al<Subscript><Emphasis Type="BoldItalic">n</Emphasis></Subscript><Emphasis Type="BoldItalic">TM</Emphasis><Superscript>+</Superscript> (<Emphasis Type="BoldItalic">TM</Emphasis> = Ti,V, Cr)

Structural information on free transition metal doped aluminum clusters, Al _n TM ⁺ (TM = Ti, V, Cr), was obtained by studying their ability for argon physisorption. Systematic size (n = 5 – 35) and temperature (T = 145 – 300 K) dependent investigations reveal that bare Al _n ⁺ clusters are inert toward argon, while Al _n TM ⁺ clusters attach one argon atom up to a critical cluster size. This size is interpreted as the geometrical transition from surface-located dopant atoms to endohedrally doped aluminum clusters with the transition metal atom residing in an aluminum cage. The critical size, n _crit , is found to be surprisingly large, namely n _crit = 16 and n _crit = 19 – 21 for TM = V, Cr, and TM = Ti, respectively. Experimental cluster–argon bond dissociation energies have been derived as function of cluster size from equilibrium mass spectra and are in the 0.1–0.3 eV range.     

Cyclotron production of <Superscript>169</Superscript>Yb: a potential radiolanthanide for brachytherapy

In the present study, ytterbium-169 was produced via the ¹⁶⁹Tm(p, n)¹⁶⁹Yb nuclear process at the AMIRS (Cyclone-30, IBA, Belgium) cyclotron, irradiating Tm₂O₃ with proton particles of 15 MeV primary energy and 20 μA current for 20 min. Deposition of Tm₂O₃ on Cu substrate was carried out via by the sedimentation method. The 543 mg of thulium(III)oxide with 108 mg of ethyl cellulose and 8 mL of acetone were used to prepare a Tm₂O₃ layer of 11.69 cm². Yields of about 0.643 MBq ¹⁶⁹Yb per μAh were experimentally obtained. ¹⁶⁹Yb was separated in 80 ± 5% radiochemical yield using liquid–liquid extraction. Solvent extraction of no-carrier-added ¹⁶⁹Yb from irradiated thulium(III)oxide target hydrochloric solution was investigated using di-(2-ethylhexyl)phosphoric acid (HDEHP).     

Kinetic studies on H<Superscript>+</Superscript>-catalysed aquation of chromium(III)-oxalato-asparaginato and chromium(III)-oxalato-histidinato complexes

Three chromium(III) complexes with asparagine (Asn) and histidine (His) of the [Cr(ox)₂(Aa)]²⁻ type, where Aa = N,O–Asn, N,O–His or N,N′–His, were obtained and characterized in solution. The complexes with N,O–Aa undergo acid-catalysed aquation to give a free amino acid and cis-[Cr(ox)₂(H₂O)₂]⁻, whereas the complex with N,N′–His undergoes parallel reaction paths: (1) isomerization to the N,O–His complex and (2) liberation of an oxalate ligand. Kinetics of the N,O–Aa complexes in HClO₄ media were studied spectrophotometrically under pseudo-first-order conditions. The absorbance changes were attributed to the chelate ring opening at the Cr–N bond. The linear dependence of rate constants on [H⁺] was established, and a mechanism for the chelate ring cleavage was postulated. The existence of a metastable intermediate with O-monodentate Aa ligand was proved experimentally. Effect of [Cr(ox)₂(Aa)]²⁻ on 3T3 fibroblasts proliferation was studied. The tests revealed low cytotoxicity of the complexes. Complexes with Ala, His and Cys are good candidates for biochromium sources.     

Synthesis,structure, and electrochemistry of <Emphasis Type="Italic">trans</Emphasis>-[Co<Superscript>III</Superscript>{(BA)<Subscript>2</Subscript>pn}(L)<Subscript>2</Subscript>]ClO<Subscript>4</Subscript> complexes

The structure, spectroscopic, and electrochemical properties of [Co{(BA)₂pn}(L)₂]ClO₄ complexes, where (BA)₂pn = N,N′-bis(benzoylacetone)-1,3-propylenediimine dianion and the two ancillary ligands (L) are pyridine, py (1), and 4-methylpyridine, 4-Mepy (2), have been investigated. These complexes have been characterized by elemental analyses, IR, UV–Vis and ¹H-NMR spectroscopy. The crystal structure of [Co{(BA)₂pn}(py)₂]ClO₄ (1) has been determined by X-ray diffraction. The coordination geometry around cobalt(III) is best described as a distorted octahedron. The electrochemical reduction of these complexes at a glassy carbon electrode in acetonitrile solution indicates that the first reduction process corresponding to Co^III–Co^II is electrochemically irreversible, which is accompanied by the dissociation of the axial N(py)–cobalt bonds. This process becomes quasi-reversible upon the addition of excess py ligands. The second reduction step of Co^II/I shows reversible behavior and is not influenced by the nature of the axial ligands. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Extraction of metal ions (Fe<Superscript>3+</Superscript>, Co<Superscript>2+</Superscript>, Ni<Superscript>2+</Superscript>, Cu<Superscript>2+</Superscript> and Zn<Superscript>2+</Superscript>) using immobilized-polysiloxane iminobis(n-2-aminophenylacetamide) ligand system

A new insoluble solid functionalized ligand system bearing chelating ligand group of the general formula P-(CH₂)₃-N[CH₂CONH(C₆H₄)NH₂]₂, where P represents [Si–O] _n polysiloxane network, was prepared by the reaction of the immobilized diethyliminodiacetate polysiloxane ligand system, P-(CH₂)₃N(CH₂CO₂Et)₂ with 1,2-diaminobenzene in toluene. ¹³C CP-MAS NMR, XPS and FTIR results showed that most ethylacetate groups (–COOEt) were converted into the amide groups (–N–C=O). The new functionalized ligand system exhibits high capacity for extraction and removal of the metal ions (Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺ and Zn²⁺) with efficiency of 95–97% after recovery from its primary metal complexes. This functionalized ligand system formed 1:1 metal to ligand complexes.     

Hydridosilazanes hydrolysis-condensation reactions studied by <Superscript>1</Superscript>H and <Superscript>29</Superscript>Si liquid NMR spectroscopy

Hydridosilazane compounds containing Si–N and Si–H bonds can be used as precursors of SiO_x materials. The hydrolysis-condensation reactions of tetramethyldisilazane, as a polyhydridosilazane model compound, were investigated by ¹H and ²⁹Si liquid NMR spectroscopy. These reactions were carried out at room temperature for up to 120 min in presence of water. The identified products are short linear siloxane species (hydride terminated polydimethylsiloxanes M^HD_xM^H) and cyclosiloxanes. Silicon hydride persistence in the reactional mixture suggested that silazane group is more sensitive to hydrolysis reaction than silicon hydride group. Moreover, additional experiments evidenced that the low steric hindrance of the silicon hydride influences the silazane hydrolysis kinetic. Hence the presence of ammonia released during silazane hydrolysis reaction was demonstrated to be a catalyst of the silicon hydride hydrolysis reaction.     

Polymer-coated magnetic nanoparticles for rapid bioassay of <Superscript>90</Superscript>Sr in human urine samples

A rapid bioassay for ⁹⁰Sr was developed involving preconcentration of ⁹⁰Sr/⁹⁰Y from human urine samples with a cation exchange polymer (poly–acrylamido–methyl–propanesulfonic acid) coated onto magnetic nanoparticles, followed by selective elution of ⁹⁰Sr (over ⁹⁰Y) with phosphate for determination by liquid scintillation analysis. The minimum detectable activity for this method (4.9 ± 0.5 Bq/L) is lower than the required sensitivity of 19 Bq/L for ⁹⁰Sr in human urine samples, as defined in the requirements for radiation emergency bioassay techniques for the public and first responders based on the dose threshold for possible medical attention recommended by the International Commission on Radiological Protection. The relative bias was 9.2%, the relative precision was 3.2%, and the linear dynamic range covered 12–600 Bq/L. This simple and rapid bioassay method is found to be in compliance with the HPS ANSI N13.30 performance criteria for radiobioassay.     

Synthesis,Spectra and Electrochemistry of Dinitro-bis-{1-alkyl-2-(arylazo) imidazole} Ruthenium(II). Nitro-nitroso Derivatives and Reactivity of the Electrophilic {Ru-NO}<Superscript>6</Superscript>System

Ag⁺ assisted aquation of blue cis-trans-cis-RuCl₂(RaaiR′)₂ (4–6) leads to the synthesis of solvento species, blue-violet cis-trans-cis-[Ru(OH₂)₂(RaaiR′)₂](ClO₄)₂ [Raai R′=p-R-C₆H₄ N=N–C₃H₂–NN–1–R′, (1–3), abbreviated as N,N′-chelator, where N(imidazole) and N(azo) represent N and N′, respectively; R = H (a), OMe (b), NO₂ (c) and R′ = Me (1/4/7/10), CH₂CH₃ (2/5/8/11), CH₂Ph (3/6/9/12)] that have been reacted with NO₂⁻in warm EtOH resulting in violet dinitro complexes of the type, Ru(NO₂)₂(RaaiR′)₂ (7–9). The nitrite complexes are useful synthons of electrophilic nitrosyls, and on triturating the compounds, (7b–9b) with conc. HClO₄ nitro-nitrosyl derivatives, [Ru(NO₂)(NO)(OMeaaiR′)₂](ClO₄)₂ (10b–12b) are isolated. The solution structure and stereoretentive transformation in each step have been established from ¹H n.m.r. results. All the complexes exhibit strong MLCT transitions in the visible region. They are redox active and display one metal-centred oxidation and successive ligand-based reductions. The redox potentials of Ru(III)/Ru(II) (E_1/2^M) of (10b–12b) are anodically shifted by ∼ ∼0.2 V as compared to those of dinitro precursors, (7b–9b). The ν(NO) >1900 cm⁻¹ strongly suggests the presence of linear Ru–NO bonding. The electrophilic behaviour of metal bound nitrosyl has been proved in one case (12b) by reacting with a bicyclic ketone, camphor, containing an active methylene group and an arylhydrazone with an active methine group, and the heteroleptic tris chelates thus formed have been characterised.     

Nucleophilic aromatic substitution by [<Superscript>18</Superscript>F]fluoride at substituted 2-nitropyridines

For the radiofluorination of benzenes and benzene derivatives, the electrophilic reaction with [¹⁸F]F₂ is a very common route. Yet, aromatic nucleophilic substitution (S_NAr) by n.c.a [¹⁸F]fluoride, which can be produced efficiently in high amounts, has been considered to be very desirable. However, to facilitate ¹⁸F-labelling via S_NAr at an electron rich aromatic system, an appropriate leaving group must be present together with an auxiliary group in ortho or para position to the leaving group. An interesting alternative for the auxiliary group is the heteroatom of a heteroaromatic system, for which pyridine is a leading example. Dolci et al. (J Label Compd Radiopharm 42:975–985, 1999) have evaluated the scope of the nucleophilic aromatic fluorination of 2-substituted pyridine rings using the activated K [¹⁸F]F-K₂₂₂ complex. As methyl and methoxy groups are known to enhance the electron density of an aromatic system by the +I and the +M effect, respectively, S_NAr is unlikely to occur. Until now, the effect of these substituents has not been studied towards the ¹⁸F-radiofluorination of substituted 2-nitropyridines by use of [¹⁸F]fluoride. Therefore, we have investigated the effect of methoxy and methyl groups in 2-nitropyridines. The results showed that 3-methoxy-2-nitropyridine and 3-methyl-2-nitropyridine can efficiently be substituted by [¹⁸F]fluoride with high RCY’s (70–89%) in short reaction times (1–30 min) at a reaction temperature of 140 °C. Moreover, 3-methoxy-6-methyl-2-[¹⁸F]fluoropyridine was obtained from the corresponding nitro-precursor in a high yield of 81 ± 1% after 30 min at 140 °C. In case of 2-nitropyridines data indicates the effect of methyl and methoxy groups on S_NAr to be of minor importance.     

Sorption behavior of Am<Superscript>3+</Superscript> on suspended pyrite

Sorption behavior of ²⁴¹Am (~10⁻⁹ M) on naturally occurring mineral pyrite (particle size: ≤70 μm) has been studied under varying conditions of pH (2–11), and ionic strength (0.01–1.0 M (NaClO₄)). The effects of humic acid (2 mg/L), other complexing anions (1 × 10⁻⁴ M CO₃ ²⁻, SO₄ ²⁻, C₂O₄ ²⁻ and PO₄ ³⁻), di- and trivalent metal ions (1 × 10⁻³ M Mg²⁺, Ca²⁺ and Nd³⁺) on sorption behavior of Am³⁺ at a fixed ionic strength (I = 0.10 M (NaClO₄)) have been studied. The sorption of ²⁴¹Am on pyrite increased with pH from 2.8 (84%) to 8.1 (97%). The sorption of ²⁴¹Am decreased with ionic strength at low pH values (2 ≤ pH ≤ 4), but was insensitive in the pH range of 4–10, suggesting the formation of outer-sphere complexes on pyrite surface at lower pH, and inner-sphere complexes at higher pH values. The sorption of ²⁴¹Am increased in the presence of (i) humic acid (5 < pH < 7.5), and (ii) C₂O₄ ²⁻ (2 < pH < 3). By contrast, other complexing anions such as (carbonate, phosphate, and sulphate) showed negligible influence on ²⁴¹Am sorption. The presence of Mg²⁺, Ca²⁺ ions showed marginal effect on the sorption profile of ²⁴¹Am; while the presence of Nd³⁺ ion suppressed its sorption significantly under the conditions of present study. The sorption of ²⁴¹Am on pyrite decreased with increased temperature indicating an exothermic process.     

Preparation and preliminary evaluation of [<Superscript>67</Superscript>Ga]-tetra phenyl porphyrin complexes as possible imaging agents

[⁶⁷Ga]labeled tetraphenyl porphyrin ([⁶⁷Ga]-TPP) was prepared using freshly prepared [⁶⁷Ga]GaCl₃ and tetraphenyl porphyrin (TPPH₂) for 30–60 min at 25 °C (radiochemical purity: >97 ± 1% ITLC, >98 ± 0.5% HPLC, specific activity: 13–14 GBq/mmol). Stability of the complex was checked in final formulation and human serum for 24 h. The partition coefficient was calculated for the compound (log P 1.89). The biodistribution of the labeled compound in vital organs of wild-type rats was studied using scarification studies and SPECT imaging up to 24 h. A detailed comparative pharmacokinetic study performed for ⁶⁷Ga cation and [⁶⁷Ga]-TPP. The complex is mostly washed out from the circulation through kidneys and can be an interesting tumor imaging/targeting agent due to low liver uptake and rapid excretion through the urinary tract.     

Reactions of [Cp*Ru(H<Subscript>2</Subscript>O)(NBD)]<Superscript>+</Superscript> with diynes

Abstract  Formal [2 + 2 + 2] addition reaction of [Cp*Ru(H₂O)(NBD)][BF₄] (NBD = norbornadiene) with 4,4′-Diethynylbiphenyl generates [C₉H₉-η⁶-C₆H₄(RuCp*)–C₆H₄(RuCp*)-η⁶-C₉H₉][BF₄]₂. The reaction of [Cp*Ru(H₂O)(NBD)][BF₄] with 1,4-diphenylbutadiyne generates the unusual [2 + 2 + 2] additional organic compound Ph–C≡C–C₉H₈–Ph in addition to the organometallic compound [Cp*Ru(η⁶-C₆H₅–C≡C–C≡C–Ph)][BF₄]. [C₉H₉-η⁶-C₆H₄(RuCp*)–C₆H₄(RuCp*)-η⁶-C₉H₉][BPh₄]₂ is generated after the reaction of compound [C₉H₉-η⁶-C₆H₄(RuCp*)–C₆H₄(RuCp*)-η⁶-C₉H₉][BF₄]₂ with Na[BPh₄]. The structure of this compound was confirmed by X-ray diffraction. A possible approach to form Ph–C≡C–C₉H₈–Ph and [Cp*Ru(η⁶-C₆H₅–C≡C–C≡C–Ph)][BF₄] is suggested. Graphical Abstract  Formal [2 + 2 + 2] addition reaction of [Cp*Ru(H₂O)(NBD)]BF₄ (NBD = norbornadiene) with 4,4′-Diethynylbiphenyl generates [C₉H₉-η⁶-C₆H₄(RuCp*)–C₆H₄(RuCp*)-η⁶-C₉H₉][BF₄]₂. The reaction of [Cp*Ru(H₂O)(NBD)][BF₄] with 1,4-diphenylbutadiyne simply generates unusual [2 + 2 + 2] additional organic compound Ph–C≡C–C₉H₈–Ph in addition to the organometallic compound [Cp*Ru(η⁶-C₆H₅–C≡C–C≡C–Ph)][BF₄]. [C₉H₉-η⁶-C₆H₄(RuCp*)–C₆H₄(RuCp*)-η⁶-C₉H₉][BPh₄]₂ is generated after the reaction of compound [C₉H₉-η⁶-C₆H₄(RuCp*)–C₆H₄(RuCp*)-η⁶-C₉H₉][BF₄]₂ with Na[BPh₄]. The structure of this compound was confirmed by X-ray diffraction. And the possible approach to form Ph–C≡C–C₉H₈–Ph and [Cp*Ru(η⁶-C₆H₅–C≡C–C≡C–Ph)][BF₄] was suggested. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Mixed ligand complexes of Fe<Superscript>III</Superscript> containing pseudohalides,nitrosyl and some mannich bases

Reactions of Pentapseudohalonitrosyl ferrate(II) with Morpholinobenzyl benzamide(MBB) and Piperidinobenzyl benzamide(PBB) formed complexes of the type, [Fe(X)₃(NO)(L–L)] where X = CN⁻, NCO⁻ and N ₃ ⁻ and L–L = Morpholinobenzyl benzamide(MBB) and Piperidinobenzyl benzamide(PBB). These compounds have been characterized by various physico-chemical techniques such as elemental analysis, molar conductance, magnetic susceptibility measurements, i.r., electronic spectra, thermal gravimetric analysis. The molecular modeling Studies have been carried out for structural analysis for some of the complexes have been carried out using Hyperchem release 7.52 professional version.     

A Combined Experimental and Theoretical Study on the Complexation of Ag<Superscript>+</Superscript> with a Hexaarylbenzene-Based Receptor

From extraction experiments and γ-activity measurements, the exchange extraction constant corresponding to the equilibrium Ag⁺(aq) + 1⋅Cs⁺(nb) ⇆ 1⋅Ag⁺(nb) + Cs⁺(aq) taking part in the two-phase water–nitrobenzene system (where 1 = hexaarylbenzene-based receptor; aq = aqueous phase, nb = nitrobenzene phase) was evaluated to be log ₁₀ K _ex(Ag⁺, 1⋅Cs⁺) = −1.0±0.1. Further, the stability constant of the hexaarylbenzene-based receptor⋅Ag⁺ complex (abbreviation 1⋅Ag⁺) in nitrobenzene saturated with water, was calculated at a temperature of 25 °C: log ₁₀ β _nb(1⋅Ag⁺) = 5.5±0.2. By using quantum mechanical DFT calculations, the most probable structure of the 1⋅Ag⁺ complex species was solved. In this complex having C₃ symmetry, the cation Ag⁺ synergistically interacts with the polar ethereal oxygen fence and with the central hydrophobic benzene ring via cation–π interaction.     

Targetry and specification of <Superscript>167</Superscript>Tm production parameters by different reactions

In recent years, there has been a rapid expansion in the use of radio nuclides for therapeutic purposes. Thulium–167 is an important radionuclide (T _1/2 = 9.25 d) due to it could be used for tumor and bone studies in nuclear medicine. ¹⁶⁷Tm complexed with hydroxy ethylene diamine tetra-acetic acid (HEDTA) could be used with the aim of bone imaging. ¹⁶⁷Tm emits a prominent γ ray of 208 keV energy and low energy electrons. This study describes calculations on the excitation functions of ¹⁶⁵Ho(α,2n)¹⁶⁷Tm, ¹⁶⁷Er(p,n)¹⁶⁷Tm, ^natEr(d,xn)¹⁶⁷Tm and ^natEr(p,xn)¹⁶⁷Tm reactions by ALICE/ASH (hybrid and GDH models) and TALYS-1.0 codes. In addition, calculated data by codes were compared to experimental data that earlier were published and TENDL-2010 database. Moreover, optimal thickness of the targets and physical yield were obtained by SRIM (stopping and range of ions in matter) code for each reaction. According to the results, the ¹⁶⁷Er(p,n)¹⁶⁷Tm and ¹⁶⁵Ho(α,2n)¹⁶⁷Tm reactions are suggested as the best method to produce ¹⁶⁷Tm owing to minimum impurities. The TALYS-1.0 code, predict the maximum cross-section of about 382 mb at 11 MeV and 849 mb at 26 MeV for ¹⁶⁷Er(p,n)¹⁶⁷Tm and ¹⁶⁵Ho(α,2n)¹⁶⁷Tm reactions, respectively. Finally, deposition of ^natEr₂O₃ on Cu substrate was carried out via the sedimentation method. The 516 mg of erbium(III)oxide with 103.2 mg of ethyl cellulose and 8 mL of acetone were used to prepare a ^natEr₂O₃ layer of 11.69 cm². ¹⁶⁷Tm was produced via the ^natEr(p,n)¹⁶⁷Tm nuclear process at 20 μA current and 15 → 7 MeV protons beam (1 h). Yield of about 3.2 MBq ¹⁶⁷Tm per μA h were experimentally obtained.