Efficient alternative of antimicrobial nanocomposites based on cellulose acetate/Cu-NPs

The current research presents an efficient, cheap, and safe antimicrobial material for widespread use based on copper nanoparticles (Cu-NPs) loaded on cellulose acetate (CA) matrix. A reduction process of CuSO₄·5H₂O has been performed to prepare Cu-NPs. The nanosized copper particles included oxidized Cu (15–20 nm). Two different loads of Cu-NPs were used in this study, 2% and 6% mol.%. The presence of Cu-NPs incorporated with CA films slightly affected the tensile index of the films, where low and high-loaded Cu-NPs enhanced the tensile index by small values ranged from 0.640 to 0.650 and 0.667, respectively. A study on the antibacterial activity of these nanocomposites was carried out for Staphylococcus aureus, Pseudomonas aeruginosa, and Candida albicans. It has been found that CA containing Cu-NPs (2%) exhibited the highest antimicrobial activity against all test microbes including S. aeureus (21 mm), P. aeruginosa (18 mm), C. albicans (19 mm), and Aspergillus niger (15 mm). Results also revealed that CA film with 6% exhibited lower activity than film with 2% Cu-NPs. The morphological properties of CA/Cu-NPs films were characterized by scanning electron microscopy and transmission electron microscope in addition to X-ray diffraction. Low-loaded Cu-NPs showed homogenous distribution through CA matrix while, the high-loaded Cu-NPs were agglomerated through CA matrix. Thermal properties illustrated the enhancement of thermal stability of the film with increasing the loaded Cu-NPs.     

The Micellization and Clouding of Nonionic Surfactant,Poly(Ethylene Glycol) t-Octylphenyl Ether (Triton X-100): Effect of Halide Ions of (Sodium Salt) Electrolytes

In this investigation, the micellization and the clouding phenomena of a nonionic surfactant, poly(ethylene glycol) t-octylphenyl ether (Triton X-100) in the absence and presence of halide ions (sodium salt) electrolytes has been reported. The critical micelle concentration (CMC) of Triton X-100 (in the absence and presence of electrolytes) was measured by surface tension measurements. A decreasing trend of CMC was found with increasing the temperature as well as the concentration of electrolyte. The effectiveness of the halide ions was found in the order: F^? > Cl^? > Br^? > I^?. The surface properties of Triton X-100 were evaluated. The thermodynamic parameters of the micellar systems of Triton X-100 were evaluated and from these thermodynamics data, it was found that in the presence of electrolyte the stability of the micellar system is more. The cloud points (CPs) of Triton X-100 were also measured in the absence and presence of halide ions of electrolytes. With the addition of halide ions of sodium salt (electrolyte), a decrease in CP values was observed and the order was found to be: F^? > Cl^? > Br^? > I^?.     

Formation and characterization of surfactant stabilized silver nanoparticles: a kinetic study

Kinetic data for the silver nitrate–ascorbic acid redox system in presence of three surfactants (cationic, anionic and nonionic) are reported. Conventional spectrophotometric method was used to monitor the formation of surfactant stabilized nanosize silver particles during the reduction of silver nitrate by ascorbic acid. The size of the particles was determined with the help of transmission electron microscope. It was found that formation of stable perfect transparent silver sol and size of the particles depend upon the nature of the head group of the surfactants, i.e., cetyltrimethylammonium bromide (CTAB), sodium dodecyl sulphate (SDS) and Triton X-100. The silver nanoparticles are spherical and of uniform particle size, and the average particle size is about 10 and 50 nm, respectively, for SDS and CTAB. For a certain reaction time, i.e., 30 min, the absorbance of reaction mixture first increased until it reached a maximum, then decreased with [ascorbic acid]. The reaction follows a fractional-order kinetics with respect to [ascorbic acid] in presence of CTAB. On the basis of various observations, the most plausible mechanism is proposed for the formation of silver nanoparticles.     

Nitro—PAPS光度法测定发样中微量铜

为建立一种快速、简便、灵敏分光光度法测定发样中微量铜,在非离子型表面活性剂聚氧乙烯月桂醚(Brij-35)及聚氧乙烯异辛基苯基醚(TritonX-100)存在下,用水溶性试剂2-(5-硝基-2-吡啶偶氮)-5-[N-正丙基-N-(3-磺酸丙基)氨基]苯酚二钠(简称Nitro-PAPS)作显色剂,光度法测定了发样中微量铜。结果表明,该法显色络合物最大吸收波长为580 nm,线性范围为0~0.5μg/mL,表观摩尔吸光数为9.32×104L/(mol.cm),回收率为99.2%~102.5%。该法应用于人发样品微量铜分析,方法简便、快速,结果准确、满意。     

The Micellization and Clouding Phenomena of a Nonionic Surfactant,Poly(ethylene glycol) t-octylphenyl ether (Triton X-100): Effect of (Chloride Salt) Electrolytes

Herein, we report the micellization and the clouding of a nonionic surfactant, poly(ethylene glycol) t-octylphenyl ether (Triton X-100), in aqueous solutions in the absence and presence of (chloride salt) electrolytes. In the absence and presence of electrolytes, the critical micelle concentration (CMC) of Triton X-100 was measured by surface tension measurements. Upon increasing the temperature as well as the concentration of electrolytes, the CMCs decreased. The surface properties and the thermodynamic parameters of the micellar systems were evaluated. From these evaluated thermodynamic parameters, it was found that in the presence of an electrolyte, the stability of the micellar system is high. The cloud points (CPs) of Triton X-100 were also measured in the absence and presence of metallic ions of electrolytes. Upon the addition of metallic ions of chloride salts (electrolytes), the decrease in CP values was observed and the order was found to be: K⁺ > Na⁺ > Li⁺ > NH⁺₄.     

Influences of surfactant and nanoparticle assembly on effective interfacial tensions

We have studied assembly at air-water and liquid-liquid interfaces with an emphasis on systems containing both surfactants and nanoparticles. Anionic surfactants, sodium dodecyl sulfate (SDS) and non-ionic surfactants, Triton X-100 and tetraethylene glycol alkyl ethers (C(8)E(4), C(12)E(4) and C(14)E(4)), effectively decrease the surface tension of air-water interfaces. The inclusion of negatively charged hydrophilic silica nanoparticles (diameters of approximately 13 nm) increases the efficiency of the SDS molecules but does not alter the performance of the non-ionic surfactants. The former is likely due to the repulsive Coulomb interactions between the SDS molecules and nanoparticles which promote the surfactant adsorption at air-water interfaces. For systems involving trichloroethylene (TCE)-water interfaces, the SDS and Triton X-100 surfactants effectively decrease the interfacial tensions and the nanoparticle effects are similar compared to those involving air-water interfaces. Interestingly, the C(12)E(4) and C(14)E(4) molecules, with or without the presence of nanoparticles, fail to decrease the TCE-water interfacial tensions. Our molecular dynamics simulations have suggested that the tetraethylene glycol alkyl ether molecules tend to disperse in the TCE phase rather than adsorb at the TCE-water interfaces.     

Spectrophotometric study of colour reaction of vanadium(IV) with Chrome Azurol S in the presence of cationic and non-ionic surfactants

The optimum conditions for the formation of complexes of vanadium(IV) with Chrome Azurol S (CAS) in the presence of cationic (benzyldodecyldimethylammonium bromide (ST)) and non-ionic (Triton X-100, Tween 20 and Brij 35) surfactants have been determined. The complexes are formed in weakly acid solution (optimum pH: 4.6, 4.0 and 3.9) and show the absorption maxima at 603, 600 and 598 nm, respectively. The highest sensitivity was obtained for the method based on quaternary system V(IV)-CAS-ST-Triton X-100 due to the higher CAS: V(IV) molar ratio in this complex than in binary and ternary complexes: V(IV)-CAS) and V(IV)-CAS-ST. The molar absorptivity of this system is 8.08 × 10⁴ L/mol cm. The LOD and LOQ values are: 0.006 and 0.02 μg/mL, respectively. Beer’s law is obeyed in the range: 0.02–0.60 μg/mL of V. The precision (RSD = 0.51%) and accuracy (1.9%) are satisfactory. This method has been applied to the determination of vanadium in plant materials.     

Microwave-Assisted Synthesis and Characterization of Triton X 100 Capped Silver Nanospheres

In this article, we report the synthesis of silver nanospheres (Ag NS) by a simple microwave irradiation method using Triton X 100 (TX 100) as a capping agent. TX 100 was also observed to act as a reducing agent in the presence of microwave radiation. From the ultraviolet-visible spectrum, the formation of Ag NS was confirmed by observing surface plasmon resonance band at 414 nm. The emission band of Ag NS was observed at 482 nm from the photoluminescence (PL) spectrum. High-resolution transmission electron microscopy (HR TEM) was used to investigate the morphology of the synthesized sample. It shows that the synthesized sample has sphere-like morphology with an average diameter of 5 nm. Further, the elemental composition of the Ag NS was determined by energy dispersive x-ray analysis (EDX). Selected area electron diffraction (SAED) was used to find the crystalline nature of the Ag NS. The interaction between Ag NS and TX 100 was established by Raman spectroscopy. The electrochemical behaviour of the synthesized Ag NS was analyzed by cyclic voltammetry (CV).     

Radioanalytical separation and size-dependent ion exchange property of micelle-directed titanium phosphate nanocomposites

Nanocomposite titanium-phosphate (TiP) of different sizes was synthesized using Triton X-100 (polyethylene glycol-p-isooctylphenyl ether) surfactant. The materials were characterized by FTIR and powdered X-ray diffraction (XRD). The structural and morphological details of the material were obtained by scanning electron microscopy (SEM) and transmission electron microscopy. The SEM study was followed by energy dispersive spectroscopic analysis for elemental analysis of the sample. The important peaks of the XRD spectra were analyzed to determine the probable composition of the material. The average size distribution of the particles was determined by dynamic light scattering method. Ion exchange capacity was measured for different metal ions with sizes of the TiP nanocomposite and size-dependent ion exchange property of the material was investigated thoroughly. The nanomaterial of the smallest size of around 43 nm was employed to separate carrier-free ^137mBa from ¹³⁷Cs in column chromatographic technique using 1.0 M HNO₃ as eluting agent at pH 5.     

Effect of the Presence of Surfactants and Immobilization Conditions on Catalysts’ Properties of <Emphasis Type="Italic">Rhizomucor miehei</Emphasis> Lipase onto Chitosan

Lipase from Rhizomucor miehei (RML) was immobilized onto chitosan support in the presence of some surfactants added at low levels using two different strategies. In the first approach, the enzyme was immobilized in the presence of surfactants on chitosan supports previously functionalized with glutaraldehyde. In the second one, after prior enzyme adsorption on chitosan beads in the presence of surfactants, the complex chitosan beads-enzyme was then cross-linked with glutaraldehyde. The effects of surfactant concentrations on the activities of free and immobilized RML were evaluated. Hexadecyltrimethylammonium bromide (CTAB) promoted an inhibition of enzyme activity while the nonionic surfactant Triton X-100 caused a slight increase in the catalytic activity of the free enzyme and the derivatives produced in both methods of immobilization. The best derivatives were achieved when the lipase was firstly adsorbed on chitosan beads at 4 °C for 1 h, 220 rpm followed by cross-link the complex chitosan beads-enzyme with glutaraldehyde 0.6% v.v^?1 at pH 7. The derivatives obtained under these conditions showed high catalytic activity and excellent thermal stability at 60° and 37 °C. The best derivative was also evaluated in the synthesis of two flavor esters namely methyl and ethyl butyrate. At non-optimized conditions, the maximum conversion yield for methyl butyrate was 89%, and for ethyl butyrate, the esterification yield was 92%. The results for both esterifications were similar to those obtained when the commercial enzyme Lipozyme® and free enzyme were used in the same reaction conditions and higher than the one achieved in the absence of the selected surfactant.     

Anodic-stripping voltammetry of heavy metals in the presence of organic surfactants

The efficacy of fumed silica for removal of sorption interferences by organic surfactants in the anodic-stripping voltammetry of heavy metals is demonstrated. Appropriate addition of silica to the sample solution rapidly "purifies" it from interfering surfactants during the nitrogen purge step. Up to at least 6 ppm of gelatin, Triton X-100, albumin or Liqui-Nox then does not affect the stripping response of cadmium, lead and zinc at the hanging mercury drop electrode. A relative standard deviation of 5.5% is obtained for 20 successive measurements of 1 x 10(-7)M lead in the presence of 2 ppm Triton X-100. Analogous improvements are observed at the mercury film electrode (in the presence of up to 60 ppm of these surfactants). The use of silica thus possesses the advantages of speed, efficiency, simplicity and low cost compared to other schemes for dealing with surfactant interferences in anodic-stripping voltammetry.     

Micellization of economically viable surfactants in CO(2)

Stability and aggregation structures of various economically viable surfactants for CO(2) are reported. The compounds are either commercially available octylphenol nonionics (Triton X-100, X-100 reduced, and X-45) or custom-made analogues of aerosol-OT (J. Am. Chem. Soc. 123 (2001) 988). These were selected to reveal the influence of chain terminal group structure, namely highly methylated t-butyl units, on solubility and aggregation in CO(2). In addition the mean ethylene oxide block length is varied for the Triton surfactants (X-100 approximately EO(10), X-45 approximately EO(8)). High-pressure small-angle neutron scattering (SANS) experiments revealed the presence of aggregates, consistent with spheroidal reverse micelles. The nonionics show a temperature and pressure dependence on solubility. These results confirm the special affinity of highly methyl-branched tails for CO(2). However, none of these systems were able to disperse significant amounts of water or brine; therefore hydrated reversed micelles or microemulsion droplets were not stabilized. Hence the utility of these cheap methyl-branched surfactants in CO(2) is limited, and so groups of greater CO(2)-philicity are needed to achieve the goal of water-hydrocarbon surfactant-CO(2) dispersions.     

Determination of Aluminium by Electrothermal Atomization Atomic Absorption Spectrometry in Serum to Characterize Hemodialysis Toxicity

A simple and cost-effective method is described for the determination of aluminum by electrothermal atomic absorption spectrometry (ET-AAS) in serum of hemodialysis patients and healthy subjects. The only preparative step required is the dissolution of the serum sample in 0.2% magnesium nitrate matrix modifier and separate diluents 0.01 M EDTA and 0.1% Triton X-100. The calibration curve was linear from 20 to 100 µg/L with correlation coefficients of 0.9993 and 0.9998 for EDTA and Triton X-100, respectively. The sensitivity of the method for aluminum at the 309.3 nm line was 74 pg. The instrumental and method limits of detection were 2.2 µg/L and 4.4 µg/L, respectively. The aluminum concentrations of forty serum samples from hemodialysis patients and healthy subjects were determined and the mean values were 170.9 ± 6.8 µg/L and 47.3 ± 9.3 µg/L, respectively, whereas the permissible limit for aluminum in blood serum is 10 µg/L. The high level of Al in serum was related to oral phosphate binding agents and dialysis treatment.     

Cd(II) determination in the presence of aqueous micellar solutions

The equilibrium constants and molar absorptivities for the fast formation of a 1:3 complex between cadmium(II) (Cd(II)) and dithizonate anion, in the presence of cationic and non-ionic surfactants, allowed a simple and fast spectrophotometric determination of total cadmium. Indeed, the molar absorptivities of the Cd(II)-dithizone (Dz) complex formed in the presence of the neutral Triton X-100 and cationic cetyltrimethylammonium bromide (CTAB) surfactants are almost twice the value observed in the standard method and the maxima of absorption are shifted by about 40 nm when compared with the standard method. Clearly, the use of neutral and cationic surfactants promotes a higher value of the molar absorptivities of the complex, resulting in an increase in the sensitivity of the method. Application of the method to the desorption of Cd(II) ions from clays is illustrated.     

A new and simple method for sulfur nanoparticles synthesis

Sulfur nanoparticles were successfully synthesized via novel water-in-oil microemulsion system. The microemulsion system contained cyclohexane as an oil phase, Triton X-100 as a surfactant, butanol as a co-surfactant and sodium polysulfide solution or hydrochloric acid solution as aqueous phase, respectively. The sulfur nanoparticles were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and Fourier transform infrared spectroscopy. The results showed that the as-prepared monoclinic sulfur nanoparticles exhibited high purity and spherical shape with an average size of about 22 nm.     

Spectrophotometric and Thermodynamic Studies of Micellar Interaction of Surfactants with p-Nitrophenol

Interaction of p-nitrophenol (NPH) with various surfactants, viz., cetylpyridinium chloride (cationic), sodium dodecylsulphate (anionic) and Triton X-100 (nonionic) are studied spectrophotometrically, in aqueous-micellar medium. The interactions are of electrostatic as well as hydrophobic nature. The strength of interaction is represented in terms of the equilibrium constants and other thermodynamic quantities of formation of the p-nitrophenol-micelle donor-acceptor complexes in addition to a shift in the acid-base equilibrium of NPH. The interaction between NPH and CPC is much stronger that with Triton X-100 whereas the interaction with SDS is very weak. Formation of 1:1 charge transfer (or electron donor-acceptor) complex is evidenced from the results. The interaction of NPH is enthalpy driven with CPC and entropy driven with Triton X-100.     

Clouding and phase behavior of nonionic surfactants in hydrophobically modified hydroxyethyl cellulose solutions

Clouding phenomena and phase behaviors of two nonionic surfactants, Triton X-114 and Triton X-100, in the presence of either hydroxyethyl cellulose (HEC) or its hydrophobically modified counterpart (HMHEC) were experimentally studied. Compared with HEC, HMHEC was found to have a stronger effect on lowering the cloud point temperature of a nonionic surfactant at low concentrations. The difference in clouding behavior can be attributed to different kinds of molecular interactions. Depletion flocculation is the underlying mechanism in the case of HEC, while the chain-bridging effect is responsible for the large decrease of cloud point for HMHEC. Composition analyses for the formed macroscopic phases were carried out to provide support for associative phase separation for the case of HMHEC, in contrast to segregative phase separation for HEC. An interesting three-phase-separation phenomenon was reported in some HMHEC/Triton X-100 mixtures at high surfactant concentrations.     

Influence of Nonionic Surfactant on Alkaline Hydrolysis of Methyl Violet Catalyzed by Cetyltrimethylammonium Bromide

The alkaline hydrolysis of methyl violet (MV) was studied by spectrophotometric method under pseudo-first-order conditions at 298 K. Cationic surfactant cetyltrimethylammonium bromide (CTAB) catalyzed the reaction. Addition of nonionic surfactant Triton X-100 (TX-100) exhibited significant influence on the CTAB catalyzed reaction by lowering the extent of catalysis. The kinetic data were analyzed by Piszkiewicz model of positive cooperativity. Linear Hill-type plots were generated with indices of cooperativity values greater than unity. The effect of counterions on the reaction rates was also studied in the presence of cationic surfactant (CTAB) and cationic–nonionic mixed surfactants (CTAB/TX-100).     

Spectrophotometric determination of iron as phenylfluorone complex sensitized with Triton X-100

Summary The effect of some surfactants and protective colloids on the absorbance of the iron(III)-phenylfluorone complex has been investigated. The binary complex formed at pH 9.0 show a molar absorptivity of 7.5×10⁴ l · mol^–1 · cm^–1 at 530 nm. In the presence of 2% Triton X-100, at the same pH, the molar absorptivity of the sensitized complex was 1.19×10⁵ l · mo^–1 · cm^–1 at 555 nm. Full colour development of the sensitized complex occurred within 25 min and Beer's law was followed up to 0.53 ppm of iron. The molar ratio and continuous variation methods indicated a 13 metal-ligand ratio for the sensitized complex. The effect of various amounts of different ions has been studied under the experimental conditions and some masking agents were recommended. The method has been applied to the determination of iron in copper and nickel metals and some non-ferrous alloys.

---

Spektralphotometrische Bestimmung von Eisen als Phenylfluoronkomplex sensibilisiert mit Triton X-100

     

PHOTOPHYSICAL AND PHOTOCHEMICAL PROPERTIES OF TRITON X-165 IN AQUEOUS AND METHANOLIC SOLUTIONS

Abstract Laser flash photolysis of the nonionic surfactant Triton X-165 was carried out at 248 nm in methanolic and aqueous solutions at different pHs. Cation radical, triplet, phenoxy radical and solvated electron were observed as the transient absorbing species. Various characteristics of these transient species and their decay constants are reported. Photoionization was found to be a major process and it was monophotonic. The results obtained are compared with the photolysis of a small molecule p -methoxytoluene (PMT). Fluorescence and phosphorescence properties of the surfactants Triton X-100, Triton X-165 and PMT are also studied. A suitable reaction scheme is proposed to account for the observed results.