Highly selective determination of ascorbic acid,epinephrine, and uric acid by differential pulse voltammetry using poly(Adizol Black B)-modified glassy carbon electrode

A polymerized film of Adizol Black B (ABB) on the surface of glassy carbon (GC) electrode was prepared for the simultaneous determination of ascorbic acid (AA), epinephrine (EP), and uric acid (UA). This new electrode presented an excellent electrocatalytic activity towards the oxidation of AA, EP, and UA by differential pulse voltammetry method. The oxidation peaks of the three compounds were well defined and had the enhanced peak currents. The separation of the oxidation peak potentials for AA–EP and EP–UA were about 180 and 130 mV, respectively. The calibration curves obtained for AA, EP, and UA were in the ranges of 2.0–1,970.0, 0.1–64.0, and 0.1–1,700.0 μmol L^–1, respectively. The detection limits (S/N?=?3) were 0.01, 0.007, and 0.02 μmol L^–1 for AA, EP, and UA, respectively. The diffusion coefficient and the catalytic rate constant for the oxidation reaction of EP at poly(ABB) film-coated GC electrode were calculated as 1.54(±0.10)?×?10^?4 cm² s^?1 and 4.5?×?10³ mol^?1 L s^?1, respectively. The present method was applied to the determination of EP in pharmaceutical, AA in commercially available vitamin C tablet, and UA in urine samples.     

Poly(m-ferrocenylaniline) modified carbon nanotubes-paste electrode encapsulated in nafion film for selective and sensitive determination of dopamine and uric acid in the presence of ascorbic acid

A nafion covered carbon nanotubes-paste electrode modified with poly(m-ferrocenylaniline), (Nf/p(FcAni)-CNTsPE), provides a novel voltammetric sensor for the selective determination of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid (AA). We studied the electrochemical activity of Nf/p(FcAni)-CNTsPE toward DA, UA, and AA by differential pulse voltammetry (DPV). DA and UA anodic peaks appear at 0.30 and 0.45 V, respectively while an anodic peak for AA was not observed. DPV oxidation peak values are linearly dependent on DA concentration over the range 1–150 μM (r² = 0.992), and on UA concentration over the range 5–250 μM (r² = 0.997). DA and UA detection limits are estimated to be 0.21 and 0.58 μM, respectively. The modified electrode shows both good selectivity and reproducibility for the selective determination of DA and UA in real samples. Finally, the modified electrode was successfully applied for the determination of DA and UA in pharmaceutical or biological sample fluids.     

Micelle-encapsulated multi-wall carbon nanotubes with photosensitive copolymer and its application in the detection of dopamine

Photosensitive copolymer P(St-alt-MAn)-co-P(VM-alt-MAn) was synthesized and employed to disperse multi-wall carbon nanotubes (MWCNTs). It was found that copolymer could form micelles in aqueous solution and adsorb onto the surface of MWCNTs to produce micelle-encapsulated MWCNTs (e-MWCNTs) by in situ photo crosslinking after irradiation with ultraviolet light and a stable suspension of e-MWCNTs in aqueous solution was obtained. When deposited onto polyaniline (PANI)-modified glassy carbon electrodes, a thin film of e-MWCNTs composite was obtained and the performance of the e-MWCNTs/PANI electrode toward dopamine was then evaluated. The experimental results suggest that the hybrid film modified electrode exhibits a dramatic electrocatalytic effect on the oxidation of dopamine (DA), as evidenced by a marked enhancement of the current response. A series of CVs was obtained by modified glassy-carbon electrodes with different size of micelles was also researched. The result shows that the peak current increased with the increasing size of micelles. A linear calibration plot was obtained in a wide range of 1.0?×?10^?7–1.0?×?10^?3 M and the detection limit was 5.0?×?10^?8 M. In addition, the interference from ascorbic acid (AA) was effectively suppressed due to the presence of the negatively charged carboxylate groups of copolymer on the outside of MWCNTs which repels AA anions and provides a transport channel only for DA cations.     

A thin poly(acridine orange) film containing reduced graphene oxide for voltammetric simultaneous sensing of ascorbic acid and uric acid

We have fabricated, in a single step, carbon ceramic electrodes modified with a poly(acridine orange) film containing reduced graphene oxide. They display electrocatalytic activity to ascorbic acid (AA) and uric acid (UA) at pH 4.5. The anodic peak potentials of AA and UA are separated by 276 mV so that they can be well resolved in cyclic voltammetry. UA and AA were simultaneously determined in a mixture at working potentials of 170 and 400 mV, respectively. Under optimized conditions, the calibration curves for AA and UA cover the 0.8–5,000 μM and 0.6–900 μM concentration range, respectively, while detection limits are 0.3 μM and 0.2 μM. The electrode was applied to determine AA and UA in urine samples.

Determination of Ascorbic Acid in the Presence of Uric Acid and Folic Acid by a Nanostructured Electrochemical Sensor Based on a TiO2 Nanoparticle Carbon Paste Electrode

A carbon paste electrode (CPE), modified with novel hydroquinone/TiO₂ nanoparticles, was designed and used for simultaneous determination of ascorbic acid (AA), uric acid (UA) and folic acid (FA). The magnitude of the peak current for modified TiO₂-nanoparticle CPE (MTNCPE) increased sharply in the presence of ascorbic acid and was proportional to its concentration. A dynamic range of 1.0–1400.0 μM, with the detection limit of 6.4 × 10^?7 M for AA, was obtained using the DPV technique (pH = 7.0). The prepared electrode was successfully applied for the determination of AA, UA, and FA in real samples.     

Graphene ceramic composite as a new kind of surface-renewable electrode: application to the electroanalysis of ascorbic acid

This study introduces a new surface-renewable electrode based on a sol–gel derived graphene ceramic composite. The electrode was prepared by dispersing graphene nanosheets into a solution of the sol–gel precursors containing methyl triethoxysilane in methanol and hydrochloric acid. During hydrolysis of methyl triethoxysilane, the graphene nanosheets are trapped in the gel. After moulding and drying the composite, it can be used as a surface-renewable electrode to which we refer as a graphene ceramic composite electrode (GCCE). Cyclic voltammograms of the hexacyanoferrate(II/III) model redox system at the GCCE were compared to those obtained with a conventional carbon ceramic electrode and showed a highly improved electron transfer rate at the GCCE. The electrocatalytic oxidation of ascorbic acid as a model analyte was then studied at working potential of 50 mV and over the 3–84 μM concentration range. It revealed a sensitivity of 6.06 μA μM^?1 cm^?2 and a detection limit of 0.82 μM. The GCCE was successfully applied to the determination of ascorbic acid in orange juice and urine samples. Advantages such as good mechanical and chemical stability, ease of fabrication, and reproducible preparation make the GCCE a potentially useful and widely applicable renewable electrode for use in routine analysis. Fig. 1

(Left) FESEM image and photograph of the graphene ceramic composite electrode (GCCE); (right) the cyclic voltammogram of the renewable GCCE in 5 mM K₃[Fe(CN)₆] solution containing 0.1 M KNO₃ at scan rate of 100 mV s^?1      

Electrochemical application of titanium dioxide nanoparticle/gold nanoparticle/multiwalled carbon nanotube nanocomposites for nonenzymatic detection of ascorbic acid

Titanium dioxide nanoparticle/gold nanoparticle/carbon nanotube (TiO₂/Au/CNT) nanocomposites were synthesized, and then characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDX). A TiO₂/Au/CNT nanocomposite-modified glassy carbon (GC) electrode was prepared using the drop coating method and was investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), differential pulse voltammetry (DPV), and amperometric current–time response (I-T). The modified material is redox-active. The nonenzymatically detected amount of ascorbic acid (AA) on the TiO₂/Au/CNT electrode showed a linear relationship with the AA concentration, for concentrations from 0.01 to 0.08 μM; the sensitivity was 117,776.36 μA?·?cm^?2?·?(mM)^?1, and the detection limit was 0.01 μM (S/N?=?3). The results indicated that the TiO₂/Au/CNT nanocomposite-modified GC electrode exhibited high electrocatalytic activity toward AA. This paper describes materials consisting of a network of TiO₂, Au, and MWCNTs, and the investigation of their synergistic effects in the detection of AA.     

Sensitive voltammetric determination of rutin at a carbon nanotubes-ionic liquid composite electrode

A new composite electrode of multiwall carbon nanotubes (MWNTs) and 1-dodecyl-3-methylimidazolium hexafluorophosphate (DDMIMPF₆) was fabricated to determine rutin. This electrode showed very attractive electrochemical performances compared to other kinds of ionic liquid modified electrodes and notably improved sensitivity and stability. Electrochemical behavior of rutin at the composite electrode had been investigated in pH 2.09 Britton–Robinson buffer solution by cyclic voltammetry and square wave voltammetry. The experimental results suggested that the composite electrode exhibited an electrocatalytic activity toward the redox of rutin. The electrochemical parameters of rutin were calculated with the results of the charge transfer coefficient (α) and the standard rate constant (k _s) as 0.48 and 2.09 s^?1. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 0.03–1.5 μM, with a detection limit of 0.01 μM (S/N?=?3). The relative standard deviation for six times successive determination of 1 μM rutin was 1.6 %. The method was successfully applied to the determination of rutin in tablets and urine samples without the influence of the coexisting substances. In addition, the MWNTs/DDMIMPF₆ composite electrode exhibits a distinct advantage of simple preparation, surface renewal, good reproducibility, and stability.     

Application of horseradish peroxidase/polyaniline/bis(2-aminoethyl) polyethylene glycol-functionalized carbon nanotube composite as a platform for hydrogen peroxide detection with high sensitivity at low potential

Polyaniline/O,O′-bis (2-aminoethyl) polyethylene glycol-functionalized multiwalled carbon nanotube (PANI/PEG–MWCNT) composite-modified electrode was successfully prepared by electropolymerization. The ionic transport in PANI/PEG–MWCNT film and its effects on the composite performance are presented. Both protonic and anionic participation in the charge compensation processes were calculated and they indicated that the presence of the PEG–MWCNT in the PANI film suppress the anionic transportation and improve the composite ability in fixing horseradish peroxidase enzyme. Finally, the adsorption between the negatively charged PANI/PEG–MWCNT nanocomposite and the positively charged Horseradish peroxidase resulted in a high sensitivity (1.01 μA L cm^?2 μmol^?1) to hydrogen peroxide. This sensor exhibited a good reproducibility and stability at an applied potential of ?100 mV vs Ag/AgCl.     

PANI–TiC nanocomposite film for the direct electron transfer of hemoglobin and its application for biosensing

A novel polyaniline and titanium carbide (PANI–TiC) nanocomposite was synthesized by an in situ chemical oxidative polymerization method, and a hydrogen peroxide (H₂O₂) biosensor was fabricated by PANI–TiC with hemoglobin (Hb)-modified glassy carbon electrode (GCE). Scanning electron microscope and energy dispersive X-ray spectroscopy showed the morphology and ingredient of PANI–TiC. Electrochemical investigation of the biosensor showed a pair of well-defined, quasi-reversible redox peaks with E _pa?=??0.318 V and E _pc?=??0.356 V (vs SCE) in 0.1 M, pH 7.0 sodium phosphate-buffered saline at the scan rate of 150 mV s^?1. Transfer rate constant (k _s) was 2.01 s^?1. The Hb/PANI–TiC/GCE showed a good electrochemical catalytic response for the reduction of H₂O₂ with the linear range from 0.5 to 285.5 μM and the detection limit of 0.2 μM (S/N?=?3). The apparent Michaelis–Menten constant (K _m) was estimated to be 1.21 μM. Therefore, the PANI–TiC as a novel matrix opened up a further possibility for study on the design of enzymatic biosensors with potential applications.     

In-situ decorated gold nanoparticles on polyaniline with enhanced electrocatalysis toward dopamine

Gold nanoparticles were in-situ decorated on top of a polyaniline film (GNPs–PANI) via the direct electroreduction of the adsorbed AuCl ₄ ^- ions on a glassy carbon electrode that previously was coated with PANI by electropolymerization. The GNPs–PANI composite and the performance of the resultant sensors were investigated in some detail. The sensor was applied to the oxidation of dopamine (DA) with improved catalytic activity. Its catalytic current showed wide linear response toward dopamine ranging from 3 to 115 μM, with a low detection limit of 0.8 μM (S/N=3). In addition, the sensor exhibits easy-operation, fast response to dopamine, as well as excellent reproducibility and stability.

Selective determination of L-dopa in the presence of ascorbic acid and uric acid using a 3D graphene foam

Three-dimensional interconnected network graphene foam (GF) was synthesized by chemical vapor deposition. The GF was transferred onto indium tin oxide glass, acting as an electrode for the selective determination of L-dopa in the presence of ascorbic and uric acid. Using differential pulse voltammetry (DPV) method, the oxidation peak current is well linear with L-dopa concentration in the range of 0.05–1 μM with a sensitivity of 2.64 μA μM^?1 and in the range of 1–40 μM with a sensitivity of 1.82 μA μM^?1. The detection limit of this electrode for L-dopa is about 20 nM. The proposed electrode can also effectively avoid the interference of ascorbic acid and uric acid, making the proposed sensor suitable for the accurate determination of L-dopa in human urine fluids. This electrode will have a wide range of potential application prospect in electrochemical detection.     

The electrochemistry of uric acid at a gold electrode modified with L-cysteine, and its application to sensing uric urine

The electrochemistry of uric acid at a gold electrode modified with a self-assembled film of L-cysteine was studied by cyclic voltammetry and differential pulse voltammetry. Compared to the bare gold electrode, uric acid showed better electrochemical response in that the anodic peak current is stronger and the peak potential is negatively shifted by about 100 mV. The effects of experimental conditions on the oxidation of uric acid were tested and a calibration plot was established. The differential pulse response to uric acid is linear in the concentration range from 1.0?×?10^?6 to ~?1.0?×?10^?4 mol?L^?1 (r?=?0.9995) and from 1.0?×?10^?4 to ~?5.0?×?10^?4 mol?L^?1 (r?=?0.9990), the detection limit being 1.0?×?10^?7 mol?L^?1 (at S/N?=?3). The high sensitivity and good selectivity of the electrode was demonstrated by its practical application to the determination of uric acid in urine samples.

Synergetic effect of Prussian blue film with gold nanoparticle graphite–wax composite electrode for the enzyme-free ultrasensitive hydrogen peroxide sensor

Enzyme-free amperometric ultrasensitive determination of hydrogen peroxide (H₂O₂) was investigated using a Prussian blue (PB) film-modified gold nanoparticles (AuNPs) graphite–wax composite electrode. A stable PB film was obtained on graphite surface through 2-aminoethanethiol (AET)-capped AuNPs by a simple approach. Field emission scanning electron microscope studies results in formation of PB nanoparticle in the size range of 60–80 nm. Surface modification of PB film on AET–AuNPs–GW composite electrode was confirmed by Fourier transform infrared attenuated total reflection (FTIR-ATR) spectroscopy studies. Highly sensitive determination of H₂O₂ at a peak potential of ?0.10 V (vs. SCE) in 0.1 M KCl PBS, pH?=?7.0) at a scan rate of 20 mVs^?1 with a sensitivity of 23.58 μA/mM was observed with the modified electrode using cyclic voltammetry. The synergetic effect of PB film with AuNPs has resulted in a linear range of 0.05 to 7,800 μM with a detection limit of 0.015 μM for H₂O₂ detection with the present electrode. Chronoamperometric studies recorded for the successive additions of H₂O₂ with the modified electrode showed an excellent linearity (R ²?=?0.9932) in the range of 4.8?×?10^?8 to 7.4?×?10^?8 M with a limit of detection of 1.4?×?10^?8 M. Selective determination of H₂O₂ in presence of various interferents was successfully demonstrated. Human urine samples and stain remover solutions were also investigated for H₂O₂ content.     

Amperometric sensor based on carbon nanotubes and electropolymerized vanillic acid for simultaneous determination of ascorbic acid,dopamine, and uric acid

This paper describes the development of a simple and efficient nanostructured platform based on multi-walled carbon nanotubes (MWCNT) functionalized with an in situ generated vanillic acid (VA) polymer. It was used as an analytical sensor for the simultaneous determination of ascorbic acid (AA), dopamine (DA), and uric acid (UA). The electropolymerization process of VA, performed on MWCNT-modified glassy carbon electrode, produces three redox systems based on quinone/hydroquinone functionality, as observed by cyclic voltammetry. The amperometric sensor has as figures of merit for the simultaneous determination of AA, DA, and UA the following values: for AA, a linear range of 5–120 μM and detection limit of 3.5 μM; for DA, a linear range of 5–120 μM and detection limit of 4.5 μM; and for UA, a linear range of 5–120 μM and a detection limit of 1.5 μM. From the obtained performance, the development of the platform based on MWCNT/poly-VA is justified for the simultaneous determination of AA, DA, and UA.     

Graphene ceramic composite as a new kind of surface-renewable electrode: application to the electroanalysis of ascorbic acid

This study introduces a new surface-renewable electrode based on a sol–gel derived graphene ceramic composite. The electrode was prepared by dispersing graphene nanosheets into a solution of the sol–gel precursors containing methyl triethoxysilane in methanol and hydrochloric acid. During hydrolysis of methyl triethoxysilane, the graphene nanosheets are trapped in the gel. After moulding and drying the composite, it can be used as a surface-renewable electrode to which we refer as a graphene ceramic composite electrode (GCCE). Cyclic voltammograms of the hexacyanoferrate(II/III) model redox system at the GCCE were compared to those obtained with a conventional carbon ceramic electrode and showed a highly improved electron transfer rate at the GCCE. The electrocatalytic oxidation of ascorbic acid as a model analyte was then studied at working potential of 50 mV and over the 3–84 μM concentration range. It revealed a sensitivity of 6.06 μA μM⁻¹ cm⁻² and a detection limit of 0.82 μM. The GCCE was successfully applied to the determination of ascorbic acid in orange juice and urine samples. Advantages such as good mechanical and chemical stability, ease of fabrication, and reproducible preparation make the GCCE a potentially useful and widely applicable renewable electrode for use in routine analysis.

(Left) FESEM image and photograph of the graphene ceramic composite electrode (GCCE); (right) the cyclic voltammogram of the renewable GCCE in 5 mM K₃[Fe(CN)₆] solution containing 0.1 M KNO₃ at scan rate of 100 mV s⁻¹

     

Differential pulse voltammetric simultaneous determination of ascorbic acid,dopamine and uric acid on a glassy carbon electrode modified with electroreduced graphene oxide and imidazolium groups

A glassy carbon electrode (GCE) was anodically oxidized by cyclic voltammetry (CV) in 0.05 M sulfuric acid to introduce hydroxy groups on its surface (GCE_ox). Next, an imidazolium alkoxysilane (ImAS) is covalently tethered to the surface of the GCE_ox via silane chemistry. This electrode is further modified with graphene oxide (GO) which, dispersed in water, spontaneously assembles on the electrode surface through electrostatic interaction and π-interaction to give an electrode of type GO/ImAS/GCE. Electroreduction of GO and GCE_ox by CV yields electroreduced GO (erGO) and an electrode of the type erGO/ImAS/GCE. This electrode displays excellent electrocatalytic activity for the oxidation of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Three fully resolved anodic peaks (at ?50 mV, 150 mV and 280 mV vs. Ag/AgCl) are observed during differential pulse voltammetry (DPV). Under optimized conditions, the linear detection ranges are from 30 to 2000 μM for AA, from 20 to 490 μM for UA, and from 0.1 to 5 μM and from 5 μM to 200 μM (two linear ranges) for DA. The respective limits of detection (for an S/N of 3) are 10 μM, 5 μM and 0.03 μM. The GCE modified with erGO and ImAS performs better than a bare GCE or a GCE modified with ImAS only, and also outperforms many other reported electrodes for the three analytes. The method was successfully applied to simultaneous analysis of AA, DA and UA in spiked human urine.

Open image in new window

Graphical abstract Differential pulse voltammetric simultaneous determination of ascorbic acid, dopamine and uric acid is achieved on a glassy carbon electrode modified with electroreduced graphene oxide and imidazolium groups, through anodic treatment of glassy carbon and silane chemistry.

     

Polymer-modified glassy carbon electrode for the electrochemical detection of quinine in human urine and pharmaceutical formulations

Glassy carbon electrode was modified by electropolymerization of 4-amino-3-hydroxynaphthalene sulfonic acid. Cyclic voltammetric study of quinine showed higher current response at the modified electrode compared to the bare and activated glassy carbon electrodes in pH 7.0 phosphate buffer solution. Under optimized conditions, a calibration curve was obtained by square wave voltammetry at the modified electrode. The linear relationship between the peak current and the concentration of quinine in the range of 1.0?×?10^?7 to 1.0?×?10^?5 M was I _pa (in microamperes)?=?6.26C (in micromolars)?+?0.2997 (R ²?=?0.999). The detection limit calculated (S/N?=?3) was 1.42?×?10^?8 M, which is much lower than similar reports. The method was successfully applied for the determination of quinine in spiked human urine, and pharmaceutical formulations and recovery values >90 % were obtained.     

Ultra-sensitive voltammetric simultaneous determination of dopamine,uric acid and ascorbic acid based on a graphene-coated alumina electrode

The authors describe the fabrication of an interconnected edge-exposed graphene nanostructure via chemical vapor deposition (CVD) of foliated graphene onto a network of alumina nanofibers. The fibers such obtained are shown to enable ultra-sensitive voltammetric determination of dopamine (DA), uric acid (UA) and ascorbic acid (AA). The electrode displays powerful and persistent electro oxidative behavior and excellent electron transport properties. Cyclic voltammetry and differential pulse voltammetry demonstrate excellent selectively and sensitivity for AA, DA and UA, with typical peaks at ?0.08 V, +0.19 V, and +0.34 V (vs. SCE), respectively. Under optimum conditions, the calibration plots are linear in the 1–80 μM range for DA, in the 1–60 μM range for UA, and in the 0.5–60 μM range for UA, with detection limits of 0.47 μM, 0.28 μM and 0.59 μM, respectively. The sensor was successfully applied to the simultaneous determination of DA and UA in the presence of AA in spiked urine sample.

Open image in new window

Graphical abstract Material with high density of graphene foliates grown over highly aligned nano-dimensional ceramic fibers is used as electrode for simultaneous highly sensitive electrochemical determination of DA in the presence of UA and AA with a considerably low limit of detection.