Simultaneous determination of dopamine and serotonin by use of covalent modification of 5-hydroxytryptophan on glassy carbon electrode

An electrochemical biosensor was fabricated by covalent modification of 5-hydroxytryptophan (5-HTP) on the surface of glassy carbon electrode (GCE). The electrode, denoted as 5-HTP/GCE, was characterized by X-ray photoelectron spectroscopy, cyclic voltammetry and differential pulse voltammetry. For comparison, tryptophan modified GCE (TRP/GCE) and serotonin modified GCE (5-HT/GCE) were prepared by the same method. It was found that electrocatalytic ability of these electrodes was in the order of 5-HTP/GCE?>?TRP/GCE?>?5-HT/GCE for the oxidation of dopamine (DA) and 5-HT. The sensor was effective to simultaneously determine DA and 5-HT in a mixture. It can resolve the overlapping anodic peaks into two well-defined voltammetric peaks at 0.24 and 0.39 V (versus SCE). The linear response is in the range of 5.0?×?10^?7–3.5?×?10^?5 mol L^?1 with a detection limit of 3.1?×?10^?7 mol L^?1 for DA, and in the range of 5.0?×?10^?6–3.5?×?10^?5 mol L^?1 with a detection limit of 1.7?×?10^?6 mol L^?1 for 5-HT (s/n?=?3), respectively.     

The electrochemistry of uric acid at a gold electrode modified with L-cysteine, and its application to sensing uric urine

The electrochemistry of uric acid at a gold electrode modified with a self-assembled film of L-cysteine was studied by cyclic voltammetry and differential pulse voltammetry. Compared to the bare gold electrode, uric acid showed better electrochemical response in that the anodic peak current is stronger and the peak potential is negatively shifted by about 100 mV. The effects of experimental conditions on the oxidation of uric acid were tested and a calibration plot was established. The differential pulse response to uric acid is linear in the concentration range from 1.0?×?10^?6 to ~?1.0?×?10^?4 mol?L^?1 (r?=?0.9995) and from 1.0?×?10^?4 to ~?5.0?×?10^?4 mol?L^?1 (r?=?0.9990), the detection limit being 1.0?×?10^?7 mol?L^?1 (at S/N?=?3). The high sensitivity and good selectivity of the electrode was demonstrated by its practical application to the determination of uric acid in urine samples.

Detection of Trace Phenol Based on Mesoporous Silica Derived Tyrosinase‐Peroxidase Biosensor

A novel electrochemical biosensor for phenol based on immobilization of tyrosinase‐peroxidase on mesoporous silica is described. The enhanced sensitivity of the tyrosinase‐horseradish peroxidase based biosensor to phenol was observed on comparing with tyrosinase or horseradish peroxidase monoenzyme modified electrodes. Two enzymes retained their enzymatic activities for phenol determination without any mediator. The preparation conditions of the biosensor are discussed. Optimization of the experimental parameters was performed with regard to pH and operating potential. The phenol sensor exhibited a fast response of less than 10 seconds. The sensitivity of the biosensor for phenol was 14 μA μM^?1 cm^?2 with a linear range from 2×10^?7 to 2.3×10^?4 M and a detection limit of 4.1×10^?9 M. The biosensor showed a good stability and reproducibility.     

One-step construction of an electrode modified with electrodeposited Au/SiO2 nanoparticles, and its application to the determination of NADH and ethanol

A new electrode was developed by one-step potentiostatic electrodeposition (at ?2.0 V for 20 s) of Au/SiO₂ nanoparticles on a glassy carbon electrode. The resulting electrode (nano-Au/SiO₂/GCE) was characterized by scanning electronic microscopy, X-ray photoelectron spectroscopy and electrochemical techniques. The electrochemical behavior of dihydronicotinamide adenine dinucleotide (NADH) at the nano-Au/SiO₂/GCE were thoroughly investigated. Compared to the unmodified electrode, the overpotential decreased by about 300 mV, and the current response significantly increased. These changes indicated that the modified electrode showed excellent catalytic activity in the oxidation of NADH. A linear relationship was obtained in the NADH concentration range from 1.0?×?10^?6 to 1.0?×?10^?4 mol?L^?1. In addition, amperometric sensing of ethanol at the nano-Au/SiO₂/GCE in combination with alcohol dehydrogenase and nicotinamide adenine dinucleotide was successfully demonstrated. A wide linear response was also found for ethanol in the range from 5.0?×?10^?5 to 1.0?×?10^?3 mol?L^?1 and 1.0?×?10^?3 to 1.0?×?10^?2 mol?L^?1, respectively. The method was successfully applied to determine ethanol in beer and biological samples.     

Self-assembly of ultra-small gold nanoparticles on an indium tin oxide electrode for the enzyme-free detection of hydrogen peroxide

A novel enzyme-free electrochemical sensor for H₂O₂ was fabricated by modifying an indium tin oxide (ITO) support with (3-aminopropyl) trimethoxysilane to yield an interface for the assembly of colloidal gold. Gold nanoparticles (AuNPs) were then immobilized on the substrate via self-assembly. Atomic force microscopy showed the presence of a monolayer of well-dispersed AuNPs with an average size of ~4 nm. The electrochemical behavior of the resultant AuNP/ITO-modified electrode and its response to hydrogen peroxide were studied by cyclic voltammetry. This non-enzymatic and mediator-free electrode exhibits a linear response in the range from 3.0?×?10^?5 M to 1.0?×?10^?3 M (M?=?mol?·?L^?1) with a correlation coefficient of 0.999. The limit of detection is as low as 10 nM (for S/N?=?3). The sensor is stable, gives well reproducible results, and is deemed to represent a promising tool for electrochemical sensing.

Amperometric Biosensor for the Determination of Phenols Using a Crude Extract of Sweet Potato (Ipomoea Batatas (L.) Lam.)

Abstract

An amperometric biosensor for the determination of phenols is proposed using a crude extract of sweet potato (Ipomoea batatas (L.) Lam.) as an enzymatic source of polyphenol oxidase (PPO; tyrosinase; catechol oxidase; EC 1.14.18.1). The biosensor is constructed by the immobilization of sweet potato crude extract with glutaraldehyde and bovine serum albumin onto an oxygen membrane. This biosensor provides a linear response for catechol, pyrogallol, phenol and p-cresol in the concentration ranges of 2.0×10^?5-4.3×10^?4mol L^?1, 2.0×10^?5-4.3×10^?4 mol L^?1, 2.0×10^?5-4.5×10^?4 mol L^?1 and 2.0×10^?5-4.5×10^?4mol L^?1, respectively. The response time was about 3–5 min for the useful response range, and the lifetime of this electrode was excellent for fifteen days (over 220 determinations for each enzymatic membrane). Application of this biosensor for the determination of phenols in industrial wastewaters is presented.     

Solid-state ion selective electrode based on polypyrrole conducting polymer nanofilm as a new potentiometric sensor for Zn2+ ion

A pencil graphite electrode (PGE) electrodeposited by a polypyrrole conducting polymer doped with tartrazine (termed as PGE/PPy/Tar) was prepared and used as a zinc (II) solid-state ion-selective electrode. For the preparation of the zinc sensor electrode, electrodeposition of a polypyrrole nanofilm was carried out potentiostatically (E _app?=?0.75 V vs SCE) in a solution containing 0.010 M pyrrole and 0.001 M tartrazine trisodium salt. A pencil graphite and Pt wire were used as working and auxiliary electrodes, respectively. The introduced electrode in the current paper can be fabricated simply and was found to possess high selectivity, exhibited wide working concentration range, sufficiently rapid response, potential stability, and very good sensitivity to Zn (II) ion. The sensor electrode showed a linear Nernstian response over the range of 1.0?×?10^?5 to 1.0?×?10^?1 M with a slope of 28.23 mV per decade change in zinc ion concentration. A detection limit of 8.0?×?10^?6 M was obtained. The optimum pH working of the electrode was found to be 5.0.     

Amperometric Tyrosinase Biosensor Based on Carbon Nanotube–Titania–Nafion Composite Film

A highly sensitive and stable amperometric tyrosinase biosensor has been developed based on multiwalled carbon nanotube (MWCNT) dispersed in mesoporous composite films of sol–gel‐derived titania and perfluorosulfonated ionomer (Nafion). Tyrosinase was immobilized within a thin film of MWCNT–titania–Nafion composite film coated on a glassy carbon electrode. Phenolic compounds were determined by the direct reduction of biocatalytically‐liberated quinone species at ?100 mV versus Ag/AgCl (3 M NaCl) without a mediator. The present tyrosinase biosensor showed good analytical performances in terms of response time, sensitivity, and stability compared to those obtained with other biosensors based on different sol–gel matrices. Due to the large pore size of the MWCNT–titania–Nafion composite, the present biosensor showed remarkably fast response time with less than 3 s. The present biosensor responds linearly to phenol from 1.0×10^?7 M to 5.0×10^?5 M with an excellent sensitivity of 417 mA/M and a detection limit of 9.5×10^?8 M (S/N=3). The enzyme electrode retained 89% of its initial activity after 2 weeks of storage in 50 mM phosphate buffer at pH 7.0.     

Determination of lead (II) ion by highly selective and sensitive lead (II) membrane electrode based on 2-(((E)-2-((E)-1-(2-hydroxyphenyl) methyliden)hydrazono)metyl)phenol

A PVC (poly vinyl chloride) membrane electrode for lead ion based on 2-(((E)-2-((E)-1-(2-hydroxyphenyl)methyliden)hydrazono)metyl)phenol (HMHMP) as a membrane carrier was prepared. This electrode exhibited linear response with Nernstian slope of 29.2?±?0.2?mV per decade within the concentration range of 2.0?×?10^?7–1.0?×?10^?1?M lead ion. The limit of detection, as determined from the intersection of the extrapolated linear segments of the calibration plot, was 8.0?×?10^?8 M. The electrode exhibited high selectivity for Pb (II). The response time of the electrode was about 5–10?s for different concentrations. The electrode is suitable for use in aqueous solutions in a pH range of 5.0–7.5. It was used as an indicator electrode in a titration of Pb (II) with chromate at constant pH. This electrode was used for the determination of lead in ore samples, and the results were in agreement with those obtained with an atomic absorption spectroscopy (AAS) method. Also lead selective electrode was used for monitoring of lead in spiked samples of the Zayanderud River and waste water by the potentiometry technique.     

Rapid voltammetric determination of maltol in some foods and beverages using a poly(methylene blue)/graphene-modified glassy carbon electrode

A novel poly(methylene blue)/graphene composite glassy carbon electrode was fabricated and the electrochemical behavior of maltol at the modified electrode was studied by cyclic voltammetry. In phosphate-buffered solution, the modified electrode exhibited excellent electrocatalytic activity towards the electrochemical oxidation of maltol. Under optimized conditions, the oxidation peak current showed a linear relationship with the concentrations of maltol in the ranges of 8.00?×?10^?7 to 4.00?×?10^?5 and 4.00?×?10^?5 to 5.40?×?10^?4 mol L^?1, with a detection limit of 6.50?×?10^?8 mol L^?1. The performance of the developed method was validated in terms of linearity (r?=?0.9981 and 0.9955), recovery (97.0?99.3 %), reproducibility (relative standard deviations?≤?3.1 %, n?=?6), and robustness. The method shows excellent sensitivity, selectivity, and reproducibility and has been successfully applied to analyzing maltol in a wide variety of food products.     

Bioelectrochemical evaluation of the total phenols content in olive oil mill wastewaters using a tyrosinase–colloidal gold–graphite–Teflon biosensor

The use of a robust tyrosinase biosensor, fabricated from graphite–Teflon rigid electrode matrices modified with gold nanoparticles, for the estimation of the total phenols content in olive oil mill wastewaters (OMW), is proposed. The performance of this bioelectrode using both continuous stirring and flow-injection amperometry was studied. A potential value of ?0.10?V was selected for the sensitive and stable detection of various phenolic compounds present in OMW samples: catechol, 3,4-dihydroxycinnamic acid (caffeic acid), 3,4-dihydroxyphenylacetic acid (DOPAC), 4-hydroxyphenylacetic acid, 4-hydroxyphenylethanol (tyrosol), and 4-hydroxyphenylpropionic acid. Using catechol as the target phenol, linear calibration graphs were obtained in the 1.0?×?10^?8???8.0?×?10^?6?mol?L^?1 (batch) and 1.0?×?10^?7???1.0?×?10^?5?mol?L^?1 (FI) concentration ranges, with slope values of 750?mA?L?mol^?1 and 103?mA?L?mol^?1, respectively. Batch amperometry was chosen for the analysis of real samples because of its higher sensitivity. For example, the limit of detection for caffeic acid was 80?nM. The ‘pool’ of phenolic compounds was estimated in OMW obtained from different extraction systems and containing phenols at diverse levels of concentration. A comparison of these results with those obtained by applying the Folin–Ciocalteau spectrophotometric reference method was carried out.     

New Copper(II) Ion-Selective Membrane Electrode Based on Erythromycin Ethyl Succinate as a Neutral Ionophore

Abstract

The potentiometric response characteristics of a new copper(II) ion-selective PVC membrane electrode based on erythromycin ethyl succinate (EES) as ionophore were investigated. The electrode exhibited a Nernstian response to Cu²⁺ ions over the activity range of 1.5 × 10^?2 to 2.0 × 10^?6 mol L^?1 with a limit of detection of 6.3 × 10^?7 mol L^?1. Stable potentials were obtained in the pH range of 5.5–6.5. The potentiometric selectivity coefficients were calculated by using fixed interference method and revealed no important interferences except for Ag⁺. This electrode was successfully applied as an indicator electrode in determination of copper ions in real water samples.     

Direct electrochemical behavior of cytochrome c, and its determination on phytic acid modified electrode

Phytic acid (PA) with its unique structure was attached to a glassy carbon electrode (GCE) to form PA/GCE modified electrode which was characterized by electrochemical impedance. The electrochemical behavior of cytochrome c (Cyt c) on the PA/GCE modified electrode was explored by cyclic voltammetry and differential pulse voltammetry. The Cyt c displayed a quasi-reversible redox process on PA modified electrode pH 7.0 phosphate buffer solution with a formal potential (E ^0′) of 57 mV (versus Ag/AgCl). The peak currents were linearly related to the square root of the scan rate in the range of 20–120 mV·s^?1. The electron transfer rate constant was determined to be 12.5 s^?1. The PA/GCE modified electrode was applied to the determination of Cyt c, in the range of 5?×?10^?6 to 3?×?10^?4 M, the currents increase linearly to the Cyt c concentration with a correlation coefficient 0.9981. The detection limit was 1?×?10^?6 M (signal/noise?=?3).     

Palladium metal electrode and its analytical application to precipitation and acid–base analysis in aqueous and non-aqueous media

Electrochemical characterization of palladium electrode has been reported. The investigated electrode showed a linear dynamic response for p-toluensulfonic acid and iodide ions in the concentrations range between 5?×?10^?1 and 1?×?10^?5 mol L^?1 with a Nernstian slope of 55 mV for p-toluensulfonic acid and 63 mV per decade for iodide ions in water, as well as 53 mV for p-toluensulfonic acid and 51 mV per decade for iodide ions in dioxane. The response time of the electrodes was less than 10 s in the used solvents. Some potential analytical applications of the sensors have been pointed. Palladium electrode for the potentiometric titrations of acids (citric, barbituric, and p-toluensulfonic acid), bases (N,N’-diphenylguanidine, tributylamine, and 2,2'–bipyridine), halides, and some real samples in aqueous and non-aqueous solutions were studied. Тetrabutylammonium hydroxide, perchloric acid, and silver nitrate proved to be very suitable titrating agents for these titrations. The standard deviation of the determination of the investigated compounds was less than 0.9 % from those obtained with a glass electrode, i.e., silver electrode.     

Carbon electrode modified with ionic liquid and multi-walled carbon nanotubes for voltammetric sensing of adenine

A voltammetric sensor was fabricated by applying a Nafion and multi-walled carbon nanotubes (MWCNTs) composite film on the surface of a carbon ionic liquid electrode (CILE), which was prepared by mixing 1-butyl-3-methylimidazolium hexafluorophosphate with graphite powder. The electrochemical behavior of adenine on the Nafion-MWCNTs/CILE was investigated in pH 5.5 buffer solution. Adenine showed an irreversible adsorption-controlled oxidation reaction with enhanced electrochemical response, which was due to the presence of high conductive MWCNTs on the CILE surface. The electrochemical parameters of adenine electro-oxidation were determined, and the experimental conditions were optimized. Under the optimal conditions, the oxidation peak current was linear to the adenine concentration over the range of 1.0?×?10^?7 to 7.0?×?10^?5 mol L^?1 with a detection limit of 3.3?×?10^?8 mol L^?1 (signal/noise?=?3). The electrode showed good stability and selectivity, and was further applied to milk powder samples with satisfactory results.     

Detection of rutin at DNA modified carbon paste electrode based on a mixture of ionic liquid and paraffin oil as a binder

A DNA-modified carbon paste electrode (DNA-CPIE) was designed by using a mixture of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate and paraffin oil as the binder. The electrochemistry of rutin at the DNA-CPIE was investigated by cyclic voltammetry and differential pulse voltammetry. Rutin exhibits a pair of reversible redox peaks in buffer solutions of pH 3.0, and respective electrochemical parameters are established. Under the optimal conditions, the oxidative peak current is linear with the concentration of rutin in the range from 8?×?10^?9 to 1?×?10^?5 mol L^?1, and the detection limit is 1.3?×?10^?9 mol L^?1 (at S/N?=?3). The electrode exhibits higher sensitivity compared to DNA modified carbon paste electrode without ionic liquid and better selectivity comparing with electrodes without DNA. It also showed good performance, stability, and therefore represents a viable method for the determination of rutin.     

Electroanalytical Characteristics of Lercanidipine and its Voltammetric Determination in Pharmaceuticals and Human Serum on Boron-Doped Diamond Electrode

The electrooxidative behavior and determination of lercanidipine (LRC) were investigated in aqueous acetonitrile medium at a boron-doped diamond electrode using voltammetric techniques. The LRC in selected supporting electrolyte presents a well-defined anodic response at 0.944 V, studied by the proposed method. The linear response was obtained in the ranges of 4 × 10^?6 to 2 × 10^?4 mmol L^?1 range in 0.5 mmol L^?1 sulfuric acid supporting electrolyte and 1 × 10^?5 to 8 × 10^?5 mmol L^?1 range in spiked serum sample for square wave voltammetric technique. No electroactive interferences from the excipients and endogenous substances were found in the pharmaceutical dosage form and in the biological sample, respectively.     

Fast detection of catechin in tea beverage using a poly-aspartic acid film based sensor

A fast and convenient analytical method is presented for the determination of catechin. The electrochemical response of catechin in pH 6.8 phosphate buffer solution is significantly enhanced by immobilization of a film of poly-aspartic acid on the surface of the glassy carbon electrode. The enhancement mechanism and effect factors such as pH value, accumulation time and scan rate, were explored. Under optimum conditions, the differential pulse voltammetry peak current of catechin is proportional to the concentration in the range from 2.5?×?10^?7 to 3.0?×?10^?5 molL^?1, with the detection limit of 7.2?×?10^?8 molL^?1. This method was also applied to the determination of catechin in tea beverage samples, and the recoveries were from 97.1% to 102.7%.     

A method based on electrodeposition of reduced graphene oxide on glassy carbon electrode for sensitive detection of theophylline

Graphene nanosheets were directly electrodeposited onto a glassy carbon electrode (GCE) from the electrolyte solution containing graphene oxide (GO); the resulting electrode (ED-GO/GCE) was characterized with scanning electron microscopy. A simple and rapid electrochemical method was developed for the determination of theophylline (TP), based on the excellent properties of ED-GO film. The result indicated that ED-GO film-modified GCE exhibited efficient electrocatalytic oxidation for TP with relatively high sensitivity and stability. The electrochemical behavior of TP at ED-GO/GCE was investigated in detail. Under the optimized conditions, the oxidation peak current was proportional to the TP concentration in the range of 8.0?×?10^?7 to 6.0?×?10^?5 mol?L^?1 with the detection limit of 1.0?×?10^?7 mol?L^?1 (S/N?=?3). The proposed method was successfully applied to green tea samples with satisfactory results.     

Determination of lead(II) in aqueous solution using carbon nanotubes paste electrodes modified with Amberlite IR-120

A new composite electrode is described for anodic stripping voltammetry determination of Pb(II) at trace level in aqueous solution. The electrode is based on the use of multiwalled carbon nanotubes and Amberlite IR-120. The anodic stripping voltammograms depend, to a large extent, on the composition of the modified electrode and the preconcentration conditions. Under optimum conditions, the anodic peak current at around ?0.57 V is linearly related to the concentration of Pb(II) in the range from 9.6?×?10^?8 to 1.7?×?10^?6 mol L^?1 (R?=?0.998). The detection limit is 2.1?×?10^?8 mol L^?1, and the relative standard deviation (RSD) at 0.24?×?10^?6 mol L^?1 is 1.7% (n?=?6). The modified electrode was applied to the determination of Pb(II) using the standard addition method; the results showed average relative recoveries of 95% for the samples analysed.