Relative hydrophobicity of equilibrium phases in biphasic systems (ionic liquid + water)

Partition coefficients for a series of dinitrophenylated (DNP) amino acids in biphasic systems composed of hydrophobic ionic liquids and water were experimentally determined. The ionic liquids used were three 1-alkyl-3-methylimidazolium tetrafluoroborates, [C_nmim][BF₄], with alkyl chain substituents hexyl, octyl, and decyl. The liquid–liquid phase diagram for the system ([C₁₀mim][BF₄] + water) was experimentally determined. DNP amino acids distribute preferentially to the IL-rich phase and ([C₁₀mim][BF₄] + water) was found to be the system with the lowest partition coefficients for the solutes studied. The experimental partition coefficients decrease as the size of the alkyl side chain in the ionic liquids increases. The free energy of transfer of a methylene group between phases was calculated through the partition coefficients, which provides a measure of the relative hydrophobicity of the equilibrium phases. It was found that the system ([C₁₀mim][BF₄] + water) presents a lower free energy (and thus a lower relative hydrophobicity) than the system ([C₈mim][BF₄] + water). In order to better understand this result, the micellar behavior of the three ionic liquids was studied. Electrical conductivities of several aqueous solutions of the ionic liquids were measured to determine the critical micelle concentration (CMC) and the degree of micelle ionization, α, of the three ionic liquids. From these two properties it was possible to obtain the free energy of micellization, ΔG_mic, for the ionic liquids.     

ARGET ATRP of acrylonitrile with ionic liquid as reaction media and 1,1,4,7,7‐pentamethyldiethylenetriamine as both ligand and reducing agent in the presence of air

[C₁₂mim][BF₄], [C₈mim][BF₄], and [C₄mim][BF₄] were first applied as reaction media for atom transfer radical polymerization using activators regenerated by electron transfer (ARGET ATRP) of acrylonitrile (AN) with 1,1,4,7,7‐pentamethyldiethylenetriamine (PMDETA) as both ligand and reducing agent in the presence of air. The rate of polymerization in [C₁₂mim][BF₄] was considerably faster than in [C₈mim][BF₄] and [C₄mim][BF₄]. ARGET ATRP of AN in [C₁₂mim][BF₄] were better controlled than in [C₈mim][BF₄] and [C₄mim][BF₄] under the same experimental conditions. With an increase in the content of PMDETA, the polymerization provided an accelerated reaction rate and a broader polymer molecular weight distribution. A slow polymerization rate and a broad polydispersity index were observed using TMEDA instead of PMDETA as both ligand and reducing agent. There was an obvious induction period with CuCl₂ instead of CuBr₂ as catalyst. Well‐defined PAN‐b‐PMMA with higher molecular weight at 104,560 and relatively broader distribution at 1.35 was successfully prepared with PAN as macroinitiator via ARGET ATRP in [C₁₂mim][BF₄] in the presence of air. The resultant fibers were obtained with the fineness at 1.17dtex and the tenacity at 6.03cN · dtex^?1. Copyright © 2010 John Wiley & Sons, Ltd.     

Reverse ATRP process of acrylonitrile in the presence of ionic liquids

An ionic liquid, 1‐butyl‐3‐methylimidazolium tetrafluoroborate ([C₄mim] [BF₄]), was first used as the solvent in azobisisobutyronitrile (AIBN)‐initiated reverse atom transfer radical polymerization (RATRP) of acrylonitrile with FeCl₃/succinic acid (SA) as the catalyst system. The polymerization in [C₄mim][BF₄] proceeded in a well‐controlled manner as evidenced by kinetic studies. Compared with the polymerization in bulk, the polymerization in [C₄mim][BF₄] not only showed the best control of molecular weight and its distribution but also provided rather rapid reaction rate with the ratio of [C₄mim][BF₄] at 200:1:2:4. The polymerization apparent activation energies in [C₄mim][BF₄] and bulk were calculated to be 48.2 and 55.7 kJ mol^?1, respectively. Polyacrylonitrile obtained was successfully used as a macroinitiator to proceed the chain extension polymerization in [C₄mim][BF₄] via a conventional ATRP process. [C₄mim][BF₄] and the catalyst system could be easily recycled and reused after simple purification and had no effect on the living nature of polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2701–2707, 2008     

离子液体型表面活性剂研究

以1-甲基咪唑为原料, 制备了6个常规离子液体: 1-正丁基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[bmim][BF₄]及[bmim][PF₆])、1-正己基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[hmim][BF₄]及[hmim][PF₆])、1-正十六烷基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[C₁₆mim][BF₄]及[C₁₆mim][PF₆])和4个功能化离子液体: 1-(2-羟乙基)-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[2-hemim][BF₄]及[2-hemim][PF₆])、1-乙氧羰基甲基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[eocmmim][BF₄]及[eocmmim][PF₆]). 研究了这两类离子液体的一些物理性能, 旨在挖掘离子液体在香料香精化妆品工业中的应用价值. 分别检测了它们与一般溶剂的互溶性, 并测定了它们的表面张力和发泡性能, 实验结果表明, 仅[C₁₆mim][BF₄]和[C₁₆mim][PF₆]具有发泡性能, 发泡力分别为68和120 mm.     

LLE for (water + ionic liquid) binary systems using [Cxmim][BF4] (x = 6, 8) ionic liquids

Liquid–liquid equilibrium diagrams were determined for (IL + water) systems using the family of ILs 1-alkyl-3-methylimidazolium tetrafluoroborates, where the alkyl groups are hexyl and octyl ([C_xmim][BF₄] with x = 6 and 8). The gravimetric method was used to determine the equilibrium compositions at temperatures ranging from 278.15 to 340.15 K. Both systems present an upper critical solution temperature (UCST), which increases from [C₆mim][BF₄] to [C₈mim][BF₄]. The experimental data were correlated using the NRTL and eNRTL models. The binary interaction parameters were calculated for each system and model, and good agreement between experimental and calculated equilibrium compositions was obtained. Finally, the apparent Gibbs energy, enthalpy and entropy of water solution in the ILs were calculated using a modified van’t Hoff equation. The three thermodynamic functions were found to be positive for both ILs.     

Tunning CO2 Separation Performance of Ionic Liquids through Asymmetric Anions

This work aims to explore the gas permeation performance of two newly-designed ionic liquids, [C₂mim][CF₃BF₃] and [C₂mim][CF₃SO₂C(CN)₂], in supported ionic liquid membranes (SILM) configuration, as another effort to provide an overall insight on the gas permeation performance of functionalized-ionic liquids with the [C₂mim]⁺ cation. [C₂mim][CF₃BF₃] and [C₂mim][CF₃SO₂C(CN)₂] single gas separation performance towards CO₂, N₂, and CH₄ at T = 293 K and T = 308 K were measured using the time-lag method. Assessing the CO₂ permeation results, [C₂mim][CF₃BF₃] showed an undermined value of 710 Barrer at 293.15 K and 1 bar of feed pressure when compared to [C₂mim][BF₄], whereas for the [C₂mim][CF₃SO₂C(CN)₂] IL an unexpected CO₂ permeability of 1095 Barrer was attained at the same experimental conditions, overcoming the results for the remaining ILs used for comparison. The prepared membranes exhibited diverse permselectivities, varying from 16.9 to 22.2 for CO₂/CH₄ and 37.0 to 44.4 for CO₂/N₂ gas pairs. The thermophysical properties of the [C₂mim][CF₃BF₃] and [C₂mim][CF₃SO₂C(CN)₂] ILs were also determined in the range of T = 293.15 K up to T = 353.15 K at atmospheric pressure and compared with those for other ILs with the same cation and anion’s with similar chemical moieties.     

Effect of addition of hydrophilic ionic liquid 3-methyl-1-pentylimidazolium tetrafluoroborate ([C5mim][BF4]) on an aqueous solution of triton X-100

The effect of addition of 3-methyl-1-pentylimidazolium tetrafluoroborate ([C₅mim][BF₄]) on the micellization of a nonionic surfactant, Triton X-100 (TX-100), has been investigated. The techniques employed to study the aggregation behavior are fluoremetry, dynamic light scattering (DLS), and transmission electron microscopy (TEM) and the concentration range covered is 0–2?wt% [C₅mim][BF₄]. The probes, viz. pyrene and pyrene-1-carboxaldehyde (PyCHO), have been used for fluorescence analysis. According to the findings, the addition of pentyl-chained ionic liquid (IL) to aqueous TX-100 results in a dramatic increase in critical micelle concentration (cmc) decrease in micellar size, and aggregation number pointing toward an overall “unfavorable” aggregation process.     

Extraction and high performance liquid chromatographic determination of 3-indole butyric acid in pea plants by using imidazolium-based ionic liquids as extractant

In this paper, imidazolium-based ionic liquids [C₄mim][PF₆], [C₆mim][PF₆], [C₈mim][PF₆], [C₆mim][BF₄] and [C₈mim][BF₄] were tested as extracting solvents for removal of 3-indole butyric acid (IBA) from aqueous media with subsequent determination using HPLC. Percent extraction of IBA was strongly affected by pH of aqueous phases and the chemical structures of ionic liquids (ILs). Extraction of IBA was quantitative in the pH values lower than pK_a of IBA. Considering both extraction and stripping efficiencies of IBA, [C₄mim][PF₆] was found to act more efficient than other studied ILs. Capacity of [C₄mim][PF₆] was 17.6 × 10⁻⁴ mmol IBA per 1.0 mL of IL. Ionic strength of aqueous phase and temperature had shown no serious effects on extraction efficiency of IBA. A preconcentration factor of 100 and a relative standard deviation of 1.16% were obtained. It was found that ionic liquid phase was reusable almost five times for extraction/stripping purposes. 3-Indole acetic acid showed interferential effect in the extraction step. In order to assess the applicability of the method, extraction and stripping of IBA from pea plants and some other samples were studied.     

Ionic liquid assisted synthesis of flowerlike Cu2O micro-nanocrystals

Novel flowerlike Cu2O micro-nanocrystals were prepared by a greener reductive reaction of cupric acetate monohydrate with ethylene glycol in aqueous solutions of [C8mim]X (X = Cl , Br , BF4 , PF6 ) and [Cnmim][BF4] (n = 4, 6, 8). The obtained microstructures of Cu2O were characterized by Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and Fourier Transform Infrared (FT-IR). The effects of cations, anions and concentration of the ionic liquids on the morphology of Cu2O were examined in some details. The results suggest that the formation of flowerlike Cu2O was governed by a [C8mim][BF4] controlled reductive reaction mechanism. As one of their applications, the Cu2O nanoparticles were used for the photocatalytic degradation of methylene blue in aqueous solution, and high photocatalytic activity was observed.     

Study of the Alkyl Chain Length on Laccase Stability and Enzymatic Kinetic with Imidazolium Ionic Liquids

The activity and stability of laccase and their kinetic mechanisms in water soluble ionic liquids (ILs): 1-butyl-3-methyl imidazolium chloride [C₄mim][Cl], 1-octyl-3-methyl imidazolium chloride [C₈mim][Cl], and 1-decyl-3-methyl imidazolium chloride [C₁₀mim][Cl] were investigated. The results show that an IL concentration up to 10% is satisfactory for initial laccase activity at pH 9.0. The laccase stability was well maintained in [C₄mim][Cl] IL when compared to the control. The inactivation of laccase increases with the length of the alkyl chain in the IL: [C₁₀mim][Cl] > [C₈mim][Cl] > [C₄mim][Cl]. The kinetic studies in the presence of ABTS as substrate allowed calculating the Michaelis–Menten parameters. Among the ILs, [C₄mim][Cl] was the suitable choice attending to laccase activity and stability. Alkyl chains in the ions of ILs have a deactivating effect on laccase, which increases strongly with the length of the alkyl chain.     

PVT properties of imidazolium-, phosphonium-, pyridinium- and pyrrolidinium-based ionic liquids using critical point constants

Song and Mason equation of state (EOS) with a simple modification has been extended to modelling PVT properties of ionic liquids (ILs). The considered ILs are [C₁mim][MeSO4], [C₁mim][CH₃OC₂H₅SO₄], [C₁mim][(CH₃)₂PO₄], [C₂mim][MeSO4], [C₂mim][BF₄], [C₂mim][SCN], [C₂eim][NTf₂], [C₄mim][C(CN)₃], [C₄mim][CF₃SO₃], [C₄mim][SCN], [C₅mim][NTf₂], [C₈mim][NTf₂], [(C₆H₁₃)₃P(C₁₄H₂₉)][Cl], [(C₆H₁₃)₃P(C₁₄H₂₉)][NTf₂], [(C₆H₁₃)₃P(C₁₄H₂₉)][Ac], [C₃mpyr][NTf₂], [C₄mpyr][NTf₂] and [Py][C₂H₅OC₂H₄SO₄]. Three temperature-dependent parameters in the proposed EOS have been scaled as functions of reduced temperature with the use of the law of corresponding states. It is shown that the knowledge of just critical temperature and critical density is sufficient to predict the PVT properties of these ILs. The overall average absolute deviation of calculated densities from literature values for 1347 data points of 18 ILs was found to be 0.58%. The predicted density of ILs from proposed EOS has been compared with those obtained by other literature work. Moreover, we indicate that the Zeno line regularity can well be predicted by proposed model for ILs.     

Study on the Conductivities of Pure and Aqueous Bromide-Based Ionic Liquids at Different Temperatures

Electrical conductivities were measured for the pure ionic liquids [C₆mim][Br] (1-hexyl-3-methylimidazolium bromide) and [C₈mim][Br] (1-octyl-3-methylimidazolium bromide) at 0.1 MPa from 293.15 to 333.15 K. Conductivity measurements were also made for the binary water + [C₆mim][Br] and water + [C₈mim][Br] systems and their ternary water + [C₆mim][Br] + [C₈mim][Br] system at 0.1 MPa and 293.15, 298.15, and 303.15 K. The conductivity data of the pure ionic liquids were correlated by the VFT (Vogel-Tamman-Fulcher) equation, and the fitting parameters and mean absolute deviations were determined. New explanations are presented for the molality-dependent behavior of the conductivity of the binary water + [C₆mim][Br] and water + [C₈mim][Br] systems. The generalized Young’s rule and the semi-ideal solution theory for conductivity were used to predict the conductivities of the ternary water + [C₆mim][Br] + [C₈mim][Br] system from the conductivities of its corresponding binary water + [C₆mim][Br] and water + [C₈mim][Br] subsystems. The predictions are in good agreement with the measured values.     

Influence of 1-alkyl-3-methylimidazolium tetrafluoroborate on the lamellar liquid crystal formed by tetraethylene glycol lauryl ether and water

Lyotropic liquid crystals (LLCs) formed in tetraethylene glycol lauryl ether–water system by the addition of 1-alkyl-3-methylimidazolium tetrafluoroborate ([C _n Mim][BF₄], n?=?2, 4, 6, 8, 10) are characterised by polarised optical microscopy and small-angle X-ray scattering techniques. A small number of [C _n Mim][BF₄] molecules can be solubilised in the liquid crystal without changing the lamellar type. These imidazolium salts are considered as an ideal kind of modifiers for the ordered structure. With different lengths of alkyl chains, [C _n Mim][BF₄] molecules appear in various domains of ordered assemblies: in the water layer for [C₂Mim][BF₄], in the water layer as well as in the polar domain for [C₄Mim][BF₄] and in the apolar domain for the other imidazolium salts with long alkyl chains. Diverse distributions of [C _n Mim][BF₄] molecules in the inner structure bring about their specific influence on the lamellar phase. These results enlighten the use of diverse alkyl-substituted imidazolium salts in modulating LLC and other assemblies and also enrich the aggregation behaviour of these assemblies.     

Theoretical study of interactions between 1-alkyl-3-methyimidazolium tetrafluoroborate and dibenzothiophene: DFT,NBO, and AIM analysis

Density functional theory is employed to study the interaction energies between dibenzothiophene (DBT) and 1-alkyl-3-methylimidazolium tetrafluoroborate ([C _n mim]⁺[BF₄]^?). The structures of DBT, 1-ethyl-3-methylimidazolium tetrafluoroborate ([C₂mim]⁺[BF₄]^?), 1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim]+[BF₄]?), 1-hexyl-3-methylimidazolium tetrafluoroborate ([C₆mim]⁺[BF₄]^?), 1-octyl-3-methylimidazolium tetrafluoroborate ([C₈mim]⁺[BF₄]^?), [C₂mim]⁺[BF₄]^?–DBT, [C₄mim]⁺[BF₄]^?–DBT, [C₆mim]⁺[BF₄]^?–DBT and [C₈mim]⁺[BF₄]^?–DBT systems are optimized systematically at the B3LYP/6-31G(d,p) level, and the most stable geometries are obtained by NBO and AIM analyses. The results indicate that DBT and imidazolium rings of ionic liquids are parallel to each other. It is found that the [BF₄]^? anion prefers to be located close to a C1–H9 proton ring in the vicinity of the imidazolium ring and the most stable gas-phase structure of [C _n mim]⁺[BF₄]^? has four hydrogen bonds between [C _n mim]+ and [BF₄]?. There are hydrogen bonding interactions, π–π and C–H–π interactions between [C₈mim]⁺[BF₄]^? and DBT, which is confirmed by NBO and AIM analyses. The calculated interaction energies for the studied ionic liquids can be used to interpret a better extracting ability of [C₈mim]⁺[BF₄]^? to remove DBT, due to stronger interactions between [C₈mim]⁺[BF₄]^? and DBT, in agreement with the experimental results of dibenzothiophene extraction by [C _n mim]⁺[BF₄]^?.     

Facile synthesis of calcium carbonate with an absolutely pure crystal form using 1-butyl-3-methylimidazolium dodecyl sulfate as the modifier

Calcium carbonate (CaCO₃) nanocrystals with controllable polymorph and morphology have been successfully synthesized with the aid of an effective control agent, a halogen-free, low-cost ionic liquid surfactant, 1-butyl-3-methylimidazolium dodecylsulfate ([C₄mim][C₁₂SO₄]) in a supersaturated aqueous solution. For the first time, facile preparation of pure lens-like vaterite, sheet-like calcite, and peanut-like aragonite was all achieved in the [C₄mim][C₁₂SO₄] aqueous solution through changing the concentration, temperature, and initial pH value and adding magnesium ions. Washed by water and ethanol, all the aggregates were free of [C₄mim][C₁₂SO₄] and can be stable at least 1 month in air. The crystal form of the aggregates changed from pure calcite to pure vaterite at room temperature only through increasing [C₄mim][C₁₂SO₄] concentration. Formation of the ordered CaCO₃ structures is mainly ascribed to the aggregation of the primary nanoparticles whose formation mechanism is related to the change of supersaturation. This study can provide a facile and environment-friendly method to fabricate CaCO₃ crystal aggregates with various morphologies and polymorphs and can be used for large-scale industrial production and biomimetic synthesis.     

1‐Octanol/Water Partition Coefficients of 1Alkyl‐3‐methylimidazolium Chloride

The solubilities of 1alkyl‐3‐methylimidazolium chloride, [C_nmim][Cl], where n=4, 8, 10, and 12, in 1octanol and water have been measured by a dynamic method in the temperature range from 270 to 370 K. The solubility data was used to calculate the 1octanol/water partition coefficients as a function of temperature and alkyl substituent. The melting point, enthalpies of fusion, and enthalpies of solid–solid phase transitions were determined by differential scanning calorimetry, DSC. The solubility of [C_nmim][Cl], where n=10 or 12 in 1octanol is comparable and higher than that of [C₄mim][Cl] in 1octanol. Liquid 1n‐octyl‐3‐methylimidazolium chloride, [C₈mim][Cl], is not miscible with 1octanol and water, consequently, the liquid–liquid equilibrium, LLE was measured in this system. The differences between the solubilities in water for n=4 and 12 are shown only in α₁ and γ₁ solid crystalline phases. Additionally, the immiscibility region was observed for the higher concentration of [C₁₀mim][Cl] in water. The intermolecular solute–solvent interaction of 1butyl‐3‐methylimidazolium chloride with water is higher than for other 1alkyl‐3‐methylimidazolium chlorides. The data was correlated by means of the UNIQUAC ASM and two modified NRTL equations utilizing parameters derived from the solid–liquid equilibrium, SLE. The root‐mean‐square deviations of the solubility temperatures for all calculated data are from 1.8 to 7 K and depend on the particular equation used. In the calculations, the existence of two solid–solid first‐order phase transitions in [C₁₂mim][Cl] has also been taken into consideration. Experimental partition coefficients (log P) are negative at three temperatures; this is evidence for the possible use of these ionic liquids as green solvents.     

Effect of imidazolium-based ionic liquids on the aggregation behavior of twin-tailed cationic gemini surfactant in aqueous solution

Micellization behavior of the twin-tailed surfactants can be modulated by the addition of various modifiers. Ionic liquids (ILs) are one of them and are documented here. The beauty of these environmentally benign neoteric molecules lies in their structural versatility. Here, we have investigated the effect of three ILs: 1-butyl-3-methylimidazolium bromide ([C₄mim][Br]), 1-hexyl-3-methylimidazolium bromide ([C₆mim][Br]), and 1-octyl-3-methylimidazolium bromide ([C₈mim][Br]) on the aggregation and surface adsorption behavior of cationic gemini surfactant, bis(hexadecyldimethyl ammonium)propane dibromide (16-3-16) through experimentally measured electrical conductivities, surface tensions, and by spectral methods (UV-vis absorbance and fluorescence measurements). The main focus of the study is to observe the effect of added ILs on the critical micelle concentration (cmc), various surface parameters, aggregation number, and size of the aggregates of gemini surfactant. The results show that the more hydrophobic ILs, that is, [C₆mim][Br] and [C₈mim][Br] behave as electrolyte at lower concentration and cosurfactant at higher concentration, whereas moderately hydrophobic IL [C₄mim][Br] acts as an electrolyte at all concentration ranges studied. The modulating effects of ILs were also compared with conventional electrolyte (NaBr) at similar conditions.     

Thermomorphic Behavior of the Ionic Liquids [C4mim][FeCl4] and [C12mim][FeCl4]

The iron‐containing ionic liquids 1‐butyl‐3‐methylimidazolium tetrachloroferrate(III) [C₄mim][FeCl₄] and 1‐dodecyl‐3‐methylimidazolium tetrachloroferrate(III) [C₁₂mim][FeCl₄] exhibit a thermally induced demixing with water (thermomorphism). The phase separation temperature varies with IL weight fraction in water and can be tuned between 100 °C and room temperature. The reversible lower critical solution temperature (LCST) is only observed at IL weight fractions below ca. 35 % in water. UV/Vis, IR, and Raman spectroscopy along with elemental analysis prove that the yellow‐brown liquid phase recovered after phase separation is the starting IL [C₄mim][FeCl₄] and [C₁₂mim][FeCl₄], respectively. Photometry and ICP‐OES show that about 40 % of iron remains in the water phase upon phase separation. Although the process is thus not very efficient at the moment, the current approach is the first example of an LCST behavior of a metal‐containing IL and therefore, although still inefficient, a prototype for catalyst removal or metal extraction.     

Room temperature ionic liquid as a novel medium for liquid/liquid extraction of metal ions

Room temperature ionic liquids (RTILs) have been used as novel solvents to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. The hydrophobic character and water immiscibility of certain ionic liquids allow their use in solvent extraction of hydrophobic compounds. In this work, a typical room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent to study liquid/liquid extraction of heavy metal ions. Dithizone was employed as a metal chelator to form neutral metal-dithizone complexes with heavy metal ions to extract metal ions from aqueous solution into [C₄mim][PF₆]. This extraction is possible due to the high distribution ratios of the metal complexes between [C₄mim][PF₆] and aqueous phase. Since the distribution ratios of metal dithiozonates between [C₄mim][PF₆] and aqueous phase are strongly pH dependent, the extraction efficiencies of metal complexes can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation, and preconcentraction of heavy metal ions with the biphasic system of [C₄mim][PF₆] and aqueous phase can be achieved by controlling the pH value of the extraction system. Preliminary results indicate that the use of [C₄mim][PF₆] as an alternate solvent to replace traditional organic solvents in liquid/liquid extraction of heavy metal ions is very promising.     

Direct electrochemical response of cytochrome c on a room temperature ionic liquid,N-butylpyridinium tetrafluoroborate,modified electrode

Cytochrome c (Cyt c) and a room temperature ionic liquid (RTIL), 2-methyl-N-butylpyridinium tetrafluoroborate ([2-MBPy][BF₄]), were immobilized on the surface of a basal plane graphite (BPG) electrode. Direct electron transfer from Cyt c to BPG electrode was clearly observed. A pair of well-defined and reversible redox peaks could be obtained in a 0.13 M [2-MBPy][BF₄] aqueous solution. The anodic and cathodic peak potentials of Cyt c were at −0.064 and −0.020 V (vs. Ag/AgCl), respectively. The results showed that [2-MBPy][BF₄] promoted the direct electron transfer between Cyt c and the BPG electrode. Cyt c immobilized on BPGE can catalyze the reduction of hydrogen peroxide. Based on this, a biosensor can be constructed to detect quantitatively hydrogen peroxide.