Fractionation of glycoforms of recombinant human erythropoietin by preparative capillary isotachophoresis

This feasibility study deals with the use of preparative capillary isotachophoresis (CITP), operating in a discontinuous fractionation mode, to the separations and isolations of glycoforms of recombinant human erythropoietin (rhEPO). The preparative CITP separations were monitored by capillary zone electrophoresis (CZE) with a hydrodynamically closed separation unit. Such a CZE system, suppressing fluctuations of the migration data linked with fluctuations of EOF and hydrodynamic flow, made possible to evaluate and compare the preparative CITP separations performed within a longer time frame. Preparative CITP, carried out in the separation unit with coupled columns of enhanced sample loadability, separating 100 microg of rhEPO in a run lasting ca. 30 min, gave the production rate higher than 55 ng/s for the rhEPO glycoforms. The preparative separations included valve isolations of the glycoforms from the ITP stack into four or six fractions. Such numbers of the fractions corresponded to typical numbers of the major glycoform peaks as resolved in CZE of rhEPO. With respect to close effective mobilities of the glycoforms and a multicomponent nature of rhEPO, the fractions contained mixtures of glycoforms with the dominant glycoforms enriched 10-100-fold, relative to the original rhEPO sample.     

Some possibilities of an analysis of complex samples by a mass spectrometry with a sample pretreatment by an offline coupled preparative capillary isotachophoresis

This work deals with an analysis of biologically important compounds in complex matrices using preparative isotachophoresis (pITP) in column coupling configuration as a sample pretreatment technique followed by a direct infusion mass spectrometry with nano‐electrospray ionization (DI‐nESI‐MS). Busereline was chosen as a model analyte, and urine was chosen as an example of complex matrix. In pITP experiments, sodium cation (10 mmol/L concentration) was used as a leading ion and β‐alanine as terminating ion (20 mmol/L concentration). The fractions, obtained by pITP pre‐separation with the assistance of the mixture of discrete spacers, were finally analyzed by DI‐nESI‐MS. It was shown that pITP performed before DI‐nESI‐MS analysis can significantly simplify complex matrix, and, due to its concentration power, pITP can consequently decrease the concentration limit of detection. The concentration of buserelin in the urine samples analyzed by pITP‐DI‐nESI‐MS was 10 μg/L (reflecting at a 8.10^?9 mol/L concentration) in our work but from the ion intensities obtained in MS as well as MS/MS analyses, it is clear that this concentration level could be several orders of magnitude lower for reliable detection and identification of buserelin in urine analyzed using pITP with DI‐nESI‐MS detection.     

Analysis of isoflavones in soy drink by capillary zone electrophoresis coupled with electrospray ionization mass spectrometry

Capillary zone electrophoresis coupled with electrospray ionization mass spectrometry (CZE–ESI-MS) has been applied for the first time for the separation and quantification of isoflavones in soy products. The proposed method was successfully applied to the determination of seven isoflavones, including aglycones and glucosides, in soy drink. The target compounds were the glucosides daidzin and genistin, and the aglycones daidzein, genistein, formononetin, biochanin A and glycitein. During CE separation in positive mode, the analytes were present as anions, and MS detection was carried out in ESI positive-ion mode. To prevent the frequent drops in current and to improve the resolution in the separation of analytes in anionic form, a programmed nebulizing gas pressure (PNP) was applied along the analysis.     

Determination of egg white lysozyme by on-line coupled capillary isotachophoresis with capillary zone electrophoresis

An on-line coupled capillary isotachophoresis - capillary zone electrophoresis method for the determination of lysozyme in selected food products is described. The optimized electrolyte system consisted of 10 mM NH(4)OH + 20 mM acetic acid (leading electrolyte), 5 mM epsilon -aminocaproic acid +5 mM acetic acid (terminating electrolyte), and 20 mM epsilon -aminocaproic acid +5 mM acetic acid +0.1% m/v hydroxypropylmethylcellulose (background electrolyte). A clear separation of lysozyme from other components of acidic sample extract was achieved within 15 min. Method characteristics, i.e., linearity (0-50 micrograms/mL), accuracy (recovery 96+/-5%), intra-assay (3.8%), quantification limit (1 microgram/ml), and detection limit (0.25 microgram/mL) were determined. Low laboriousness, sufficient sensitivity and low running costs are important attributes of this method. The developed method is suitable for the quantification of the egg content in egg pasta.     

On-line column coupled isotachophoresis-capillary zone electrophoresis hyphenated with tandem mass spectrometry in drug analysis: Varenicline and its metabolite in human urine

A new highly advanced analytical approach, based on two-dimensional column coupled CE (ITP-CZE) hyphenated with tandem mass spectrometry (MS/MS, here triple quadrupole, QqQ) was developed, evaluated and applied in biomedical field in the present work. Capillary isotachophoresis (ITP) coupled on-line with capillary zone electrophoresis (CZE) used in hydrodynamically closed separation system was favorable for increasing the sample load capacity, increasing the analyte concentration, and removing the deteriorative highly conductive major matrix constituents. These factors considerably reduced the concentration limits of detection (cLOD) and external sample preparation (comparing to single column CZE), and, by that, provided favorable conditions for the mass spectrometry (enhanced signal to noise ratio, reproducibility of measurements, working life of MS). Here, the CZE–ESI combination provided more effective interfacing than ITP–ESI resulting in both a higher obtainable intensity of MS detection signal of the analyte as well as reproducibility of measurements of the analyte’s peak area. The optimized ITP-CZE–ESI-QqQ method was successfully evaluated as for its performance parameters (LOD, LOQ, linearity, precision, recovery/accuracy) and applied for the direct identification and ultratrace (pg mL⁻¹) determination of varenicline and, in addition, identification of its targeted metabolite, 2-hydroxy-varenicline, in unpretreated/diluted human urine. This application example demonstrated the real analytical potential of this new analytical approach and, at the same time, served as currently the most effective routine clinical method for varenicline.     

Analysis of enantiomers in biological matrices by charged cyclodextrin-mediated capillary zone electrophoresis in column-coupling arrangement with capillary isotachophoresis

The possibility to apply charged chiral selector as buffer additive in capillary zone electrophoresis (CZE) on-line coupled with capillary isotachophoresis (CITP) was studied. Enantioseparations and determinations of trace (ng/ml) antihistaminic drugs [pheniramine (PHM), dimethindene (DIM), dioxopromethazine (DIO)] present in samples of complex ionic matrices (urine) served as model examples. A negatively charged carboxyethyl-β-cyclodextrin (CE-β-CD) was used as a chiral selector in analytical CZE stage following upon a sample pretreatment by CITP (preconcentration of the analytes from 5 to 20-times diluted urine samples, partial sample clean up removing macroconstituents from the sample matrices). A high recognition capability of the oppositely charged CE-β-CD was demonstrated by enantioselective retardation of the drugs in presence of micro-and semi-macroconstituents migrating in CZE stage and detectable by UV detector. In this way, enantiomers of the drugs could be easily separated and determined. Due to lack of interferences between the drugs and sample-matrix constituents in presence of charged CE-β-CD, demands on both spacers in CITP step and multiple column-switching were minimized. CITP-CZE method with charged selector appeared to be a useful analytical approach for the trace enantiomers in complex ionic matrices as it combined enhanced separation selectivity and sample loadabitlity with high separation efficiency and provided favorable performance parameters including sensitivity, linearity, precision, accuracy/recovery and robustness with minimal demands on sample preparation. Analysis of urine sample taken from a patient treated by PHM, showing concentration profile of PHM enantiomers and their metabolites, illustrated potentialities of the method in clinical research.     

Confirmation of vanadium complex formation using electrospray mass spectrometry and determination of vanadium speciation by sample stacking capillary electrophoresis

Capillary zone electrophoresis (CZE) with UV detection was used to determine vanadium species. Nitrilotriacetic acid (NTA), hydroxyethylethylenediaminetriacetic acid (HEDTA), ethylenediaminetetraacetic acid (EDTA), diethylenetriaminepentaacetic acid (DTPA), ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) and 2,6-pyridinedicarboxylic acid (PDCA) were investigated to determine whether these ligands formed stable anionic complexes with vanadium. Of all the ligands studied HEDTA was the most suitable ligand because it gave the largest UV response with reasonable migration time. Electrospray mass spectrometry (ES-MS) was used to confirm the formation of [VO₂(HEDTA)]²⁻ and [VO(HEDTA)]¹⁻ in solution. An electrolyte containing 25 mM phosphate, 0.25 mM tetradecyltrimethylammonium bromide (TTAB) at pH 5.5 was optimum for the separation of these anionic vanadium complexes. Sample stacking techniques, including large-volume sample stacking (LVSS) and field-amplified sample injection (FASI), were tested to improve the sensitivity. Best sensitivity was obtained using FASI, with detection limits of 0.001 μM, equivalent to 0.4 μg L⁻¹, for [VO₂(HEDTA)]²⁻ and 0.01 μM, equivalent to 3.4 μg L⁻¹ for [VO(HEDTA)]¹⁻. The utility of the method for the speciation of V(IV) and V(V) was demonstrated using ground water samples.     

Comparison of hydrodynamically closed two‐dimensional capillary electrophoresis coupled with ultraviolet detection and hydrodynamically open capillary electrophoresis hyphenated with mass spectrometry in the bioanalysis of varenicline

Two capillary electrophoresis methods for monitoring renally excreted varenicline, a highly effective drug prescribed for smoking cessation, in human urine were developed and compared. A method combining capillary electrophoresis with mass spectrometry was proposed for the fast analysis of varenicline (analysis time up to 7 min). Here, mass spectrometry was a prerequisite for achieving high sensitivity and selectivity of the analysis suitable for the quantification of a 15 ng/mL level of varenicline in un‐pretreated urine matrices. An alternative approach, two‐dimensional (column‐coupled) capillary electrophoresis with enhanced sample load capacity and ultraviolet detection, was proposed as a low‐cost alternative to capillary electrophoresis with mass spectrometry. The isotachophoresis on‐line sample treatment included simple elimination of the major matrix constituents and stacking of the sample in a large volume so that threefold lower quantitation limits could be easily achieved in comparison to the capillary electrophoresis with mass spectrometry. On the other hand, longer analysis time (ca. 4.5‐fold) and more complex electrolyte system in the coupled zone electrophoresis step (including two additives enhancing separation selectivity, i.e. isopropanol and cyclodextrin) were prerequisites for the complete separation of varenicline from the sample matrix. Anyway, both the developed methods were validated according to the Food and Drug Administration guidelines showing favorable performance parameters, suitable for their routine biomedical use.     

Determination of quinine in beverages by online coupling capillary isotachophoresis to capillary zone electrophoresis with UV spectrophotometric detection

The present study illustrates the possibilities of capillary isotachophoresis (CITP) online coupled with capillary zone electrophoresis (CZE) and hyphenated with fiber-based spectrophotometric diode array detection (DAD) for the direct, highly reliable, and ultrasensitive determination of quinine (QUI) in real multicomponent ionic matrices (beverages). Here, the CITP provided an effective online sample pretreatment (preseparation and preconcentration) prior to the CZE separation. Due to the CITP sample preconcentration, a simple UV-visible absorbance spectrophotometric detection was sufficient for obtaining very low concentration limits of detection (~2.3 ng/mL). Enhanced separation selectivity due to the combination of different separation mechanisms (CITP vs. CZE) enabled to obtain a pure analyte zone, suitable for its detection and quantitation in the directly injected real samples. The spectrophotometric DAD, unlike single wavelength UV detection, enabled to characterize the purity (i.e. spectral homogeneity) of the analyte zone and preliminary data indicate structurally related compounds via characteristic spectra recorded in the interval of 200-600 nm. The proposed CITP-CZE-DAD method was characterized by favorable performance parameters (sensitivity, linearity, precision, recovery, accuracy, robustness, and selectivity) and successfully applied to the control of QUI and potential QUI impurities in commercial beverages. This method is proposed as a routine automatized method for the highly reliable quality food control.     

Analysis of 5-methyltetrahydrofolate in human blood, serum and urine by on-line coupling of capillary isotachophoresis and zone electrophoresis

The predominant circulating folate coenzyme in plasma/serum, 5‐methyltetrahydrofolate (5‐MTHF) was determined in human blood, serum and urine using a method based on the hyphenation of capillary ITP and zone electrophoresis. Measurements were done with a commercially available instrument for capillary isotachophoresis equipped with a column‐switching system. The choice of electrolytes was limited by the instability of 5‐MTHF and volatility of electrolytes for the potential coupling of the instrumentation with MS detector. To get an insight into the separability of individual sample components in an isotachophoretic analysis, we constructed zone existence diagrams for isotachophoretic electrolyte systems having a leading electrolyte composed of acetate and ammonium of pH 4.5 and 7.0, hydrocarbonate and ammonium, pH 7.8, chloride and ammonium, pH 5.6, and chloride and creatinine, pH 5.0, with hydroxide ion as the terminator. For isotachophoretic preseparation, the non‐volatile leading electrolyte with good buffering capacity composed of 1×10⁻² M HCl and 2.5×10⁻² M creatinine, pH 5.0, and terminating electrolyte composed of 1×10⁻² M MES was selected as the most suitable. The optimum BGE for CZE analysis from the standpoint of analyte stability, separability and volatility for MS coupling was 1×10⁻² M acetate with 3.5×10⁻² M ammonium, pH 4.5. Using this combination of electrolytes, LODs reached with optical detection at 220 nm were 1.6×10⁻⁷ M in human blood, 1.1×10⁻⁷ M in human serum and 4.7×10⁻⁶ M in human urine. Estimated content of 5‐MTHF in blood and serum samples of women following oral daily administration of 0.8 mg of folic acid was 1.2×10⁻⁵ and 5.8×10⁻⁶ M, respectively.     

Arsenic speciation by coupling capillary zone electrophoresis with mass spectrometry

Summary Capillary zone electrophoresis (CZE) has been coupled with mass spectrometry to enable the identification of mineral and organometallic compounds of arsenic in speciation studies. The electrophoretic effluent was introduced through a concentric interface into the mass spectrometer. Make-up liquid was added to enable electric contact at the outlet of the separation capillary and to assist the electronebulization process. After ionization, the ions were analyzed and quantified with an ion-trap detector. Optimization of the coupling conditions (geometry of the concentric interface, composition and flow rate of the sheath liquid, electronebulization and detection conditions) is described. The results show that the geometry of the concentric interface and the positioning of the outlet of the separation capillary have a critical effect on stability and sensitivity. Programming the electronebulization and detection conditions throughout the analysis enabled identification and quantification of the seven arsenic compounds of interest (neutral, and positively or negatively charged species) in less than 20 min at the ppm level. Limits of detection ranged from 0.5 to 3.3 mg L⁻¹, corresponding to amounts injected ranging from 15 to 60 pg. The linear dependence of mass spectrometric response on arsenic concentration was verified for concentrations ranging from 5 to 200 mgL⁻¹. For the two positively charged species, arsenobetaine and arsenocholine, an on-line preconcentration technique (field-amplified sample injection) enabled reduction of the detection limits by approximately one order of magnitude to 110 and 160 μgL⁻¹, respectively.     

Twenty years of interface development for capillary electrophoresis-electrospray ionization-mass spectrometry

Capillary electrophoresis-electrospray ionization-mass spectrometry has the potential to become a preferred tool for the analysis of biological mixtures and other complex samples. The development of improved interfaces in the past twenty years has been critical in demonstrating the feasibility of this technique. However, a compromise still exists between interfaces that give optimal performance and those that are practical for commercial applications. The first section of this review focuses on the technological advances in CE-ESI-MS as they relate to the key interface features for both sheath-flow and sheathless systems: delivery of the sheath liquid, shaping of the emitter tip, formation of electrical contact, and practicality in terms of ease of use and lifetime. In the second section, we review the fundamental processes that affect interface performance. Because of the complex natures of both capillary electrophoresis and electrospray ionization, flow rate, arrangement of the electrical circuit, electrochemistry, tip geometry and location of electrical contact must all be carefully managed in the design of a successful interface.     

高效毛细管区带电泳法快速测定尿液中的肌酐

建立了一种快速测定尿中肌酐浓度的高效毛细管电泳方法。利用非涂层石英毛细管(64.5 cm×50μm i.d),以pH 2.5,0.1 mmol/L H3PO4作为电泳缓冲液,检测波长191 nm,用0.05 Pa压力进样4 s,在电压16 kV快速分离尿液中的肌酐,采用外标法定量。肌酐的迁移时间约为5.5 min,肌酐浓度在34.5~8840μmol/L范围内呈良好的线性(r2=0.999)。平均日内精密度为2.5%,日间精密度为3.0%。回收率94.1%~99.0%。与全自动生化分析仪碱性苦味酸速率法相比有良好的相关性(r=0.990,n=56)。高效毛细管电泳法测定尿肌酐可应用于临床样品的检测。     

Capillary electrophoresis-electrospray ionization mass spectrometry using uncoated fused-silica capillaries and alkaline buffer solution for the analysis of small carboxylic acids

A simple and cost-effective capillary electrophoresis/mass spectrometric (CE/MS) method for the analysis of small carboxylic acids including succinate, malate, tartarate, maleinate and citrate, is described. All CE/MS experiments were performed with uncoated fused-silica capillaries and with alkaline volatile buffer solution (ammonium formate buffer, pH 10). Since sheath liquids have significant effects on the sensitivity in typical CE/MS applications, the effects of type and flow rate of the sheath liquids on the sensitivity of carboxylic acids were investigated. As the result, the best sensitivity was obtained with the alkaline sheath liquid (5 mM ammonium hydroxide in water/methanol (50/50, v/v) solution) at 6 μl min⁻¹. With the alkaline volatile buffer solution, sufficient electroosmotic flow (EOF) to carry all small carboxylic acids toward the cathode (MS side) was obtained, although all analytes had different electrophoretic mobilities toward the anode (the CE inlet). Taking advantage of the relatively higher EOF velocity, several carboxylic acids could be detected by MS in ESI-negative mode with a short analysis time. The R.S.D. values (n=5) for the migration time and the peak area of the carboxylic acids tested were less than 0.6 and 4.2%, respectively. The method was applied to the CE/MS analysis of carboxylic acids in apple juice to demonstrate the applicability to real samples.     

Determination of brominated phenols in water samples by on-line coupled isotachophoresis with capillary zone electrophoresis

A method for determination of nine brominated phenols as environmental risk compounds was developed by on-line coupled capillary isotachophoresis and capillary zone electrophoresis (ITP–CZE). For ITP step, 1 × 10⁻² mol L⁻¹ hydrochloric acid with 3 × 10⁻² mol L⁻¹ ammediol pH 9.1 was used as the leading electrolyte, and 3 × 10⁻² mol L⁻¹ β-alanine with 2 × 10⁻² mol L⁻¹ sodium hydroxide pH 10.05 was used as the terminating electrolyte. As the background electrolyte for CZE separation, 2.5 × 10⁻² mol L⁻¹ β-alanine with 2.5 × 10⁻² mol L⁻¹ lysine pH 9.6 was used. All electrolytes contained 0.05% or 0.1% (m/v) hydroxyethylcellulose to suppress the electroosmotic flow. UV detection at wavelength 220 nm was used. Detection limits in order of tens of nmol L⁻¹ were achieved. Good repeatability of migration times (less than 0.33% RSD) and good repeatability of peak areas (less than 7.19% RSD) at concentration level 5 × 10⁻⁸ mol L⁻¹ were observed. Developed ITP–CZE method was applied to determination of brominated phenols in spiked tap and river water samples.     

Micelle to solvent stacking of organic cations in capillary zone electrophoresis with electrospray ionization mass spectrometry

The direction of the effective electrophoretic mobility of small organic cations in micellar electrokinetic chromatography using sodium dodecyl sulphate in a low-pH electrolyte can be reversed in the presence of organic solvent. This effective electrophoretic mobility change is presented here as a new dimension for on-line sample preconcentration of cations in capillary zone electrophoresis (CZE) using a background solution (BGS) modified by an organic solvent. The sample is prepared in a micellar solution without organic solvent. The focusing effect relies on the reversal in the effective electrophoretic mobility at the boundary zone between the micellar matrix and the BGS modified with organic solvent. This on-line sample preconcentration technique, called micelle to solvent stacking (MSS) afforded more than an order of magnitude improvement in concentration sensitivity compared to typical CZE-UV or CZE-electrospray ionization (ESI) MS analysis. The calculated limit of detection (S/N = 3) for pindolol and metoprolol analysed by MSS-CZE-ESI-MS was found to be 0.03 and 0.01 μg/mL, respectively.     

Evaluation of the electrophoretic behaviour of opioid peptides Separation by capillary electrophoresis-electrospray ionization mass spectrometry

A general equation established in a previous study was used to model the electrophoretic mobility of a series of opioid peptides as a function of pH of the separation electrolyte. The concordance between the predicted and the experimental electrophoretic mobilities was excellent and the optimum pH for the separation of the modelled compounds could be predicted from a limited amount of experimental data. The equations were also useful for the accurate determination of the ionization constants of the polyprotic analytes. It was also demonstrated that if ionization constant values are known, the CE separations of the studied peptides can easily be predicted taking into account the classical semiempirical relationships between electrophoretic mobility and charge-to-mass ratio (m_e versus q/M^α). The separations simulated considering the accurate charge-to-mass ratios of each peptide at a certain pH value were in good agreement with the experimental results.Once an optimum separation pH value and a running buffer compatible with electrospray mass spectrometry (ESI) detection were selected, a method for the separation and characterization of this series of analytes by capillary electrophoresis-electrospray ionization mass spectrometry (CE-ESI-MS) was established using a commercial sheath-flow interface. Method validation was performed in order to prove the suitability of the proposed method for quantitative analysis. Thus, quality parameters, such as repeatability, reproducibility, limits of detection and linearity were determined.     

Feasibility of nonvolatile buffers in capillary electrophoresis-electrospray ionization-mass spectrometry of proteins

The combination of capillary electrophoresis (CE) and electrospray ionization-mass spectrometry (ESI-MS) via a triaxial interface was studied as a potential means for the characterization of intact proteins. To evaluate the possibility to use a nonvolatile electrolyte for CE, the effect of sodium phosphate and ammonium borate on the MS signal of the proteins insulin, myoglobin, and bovine serum albumin (BSA) was investigated by employing infusion experiments, and compared to the effect of ammonium formate and formic acid. The study shows that with formic acid (50 mM, pH 2.4) the most intense protein signals were obtained, while the use of sodium phosphate buffer (5 and 10 mM, pH 7.5) almost completely diminished the MS response. Ammonium formate and ammonium borate (up to 100 mM, pH 8.5) also caused protein ion suppression, but especially with the borate buffer significant MS intensity remained. MS analysis of myoglobin revealed the loss of the heme group when an acidic CE electrolyte was used. Using a background electrolyte containing 25 mM ammonium borate (pH 8.5), it is demonstrated that a CE separation of a protein test mixture can be monitored with ESI-MS without degrading the MS performance allowing molecular weight determinations of the separated compounds. In the presence of borate, detection limits were estimated to be 5-10 microM (ca. 100 fmol injected). The usefulness of the CE-MS system employing a borate buffer is indicated by the analysis of a stored sample of BSA revealing several degradation products. A sample of placental alkaline phosphatase (PLAP), a potential therapeutic agent, was also analyzed by CE-MS indicating the presence of a protein impurity. Probably due to insufficient ionization of the PLAP (a complex glycoprotein), no MS signals of the intact protein were observed.     

Determination of effective charges and ionic mobilities of polycationic antimicrobial peptides by capillary isotachophoresis and capillary zone electrophoresis

Capillary ITP (CITP) and CZE were applied to the determination of effective charges and ionic mobilities of polycationic antimicrobial peptides (AMPs). Twelve AMPs (deca‐ to hexadecapeptides) containing three to seven basic amino acid residues (His, Lys, Arg) at variable positions of peptide chain were investigated. Effective charges of the AMPs were determined from the lengths of their ITP zones, ionic mobilities, and molar concentrations, and from the same parameters of the reference compounds. Lengths of the ITP zones of AMPs and reference compounds were obtained from their CITP analyses in cationic mode using leading electrolyte (LE) composed of 10 mM NH₄OH, 40 mM AcOH (acetic acid), pH 4.1, and terminating electrolyte (TE) containing 40 mM AcOH, pH 3.2. Ionic mobilities of AMPs and singly charged reference compounds (ammediol or arginine) were determined by their CZE analyses in the BGE of the same composition as the LE. The effective charges numbers of AMPs were found to be in the range 1.65–5.04, i.e. significantly reduced as compared to the theoretical charge numbers (2.86–6.99) calculated from the acidity constants of the analyzed AMPs. This reduction of effective charge due to tightly bound acetate counterions (counterion condensation) was in the range 17–47% depending on the number and type of the basic amino acid residues in the AMPs molecules. Ionic mobilities of AMPs achieved values (26.5‐38.6) × 10⁻⁹ m²V⁻¹s⁻¹ and in most cases were in a good agreement with the ratio of their effective charges and relative molecular masses.     

Determination of some heavy metal cations in molten snow by transient isotachophoresis/ capillary zone electrophoresis

Online combination of transient ITP and CZE is employed for the determination of Cd(II), Pb(II), Cu(II), Ni(II), and Zn(II). Acetic acid is used for creating the transient isotachophoretic state. alpha-Hydroxyisobutyric acid and 4-aminopyridine are used as BGEs for the separation and indirect UV detection. At optimum conditions, the method allows to determine the metals at levels of 40-120 microg/L, about 50 times more sensitive than conventional CZE. In combination with a 20-fold evaporative concentration, the method is suitable for environmental monitoring of the heavy metals in snow samples.